※It is inexpensive because there are many scratches and there are no second-tier metal fittings at all. The horizontal rack can be used for a wide range of purposes, such as for AV on televisions, etc., and for audio. Compatible with a total load capacity of up to 300 kg. There is a feeling of use such as scratches. ※Shipping costs will be estimated separately (Daiki Goto)
Accessories: none
Main specifications: load capacity: top plate 150 kg or less, shelf board 50 kg or less, bottom plate 50 kg or less W1,165 x H492 x D580 mm weight 62 kg
Oyaide record stabilizer. The vibration mode is optimized with a hybrid configuration of aluminum, brass, and texalum. Unnecessary vibrations associated with platter rotation are attenuated, and sound groove tracing is dramatically improved. It can also be used as an EP stabilizer by reversing it up and down (Daiki Goto)
Accessories: original box, instruction manual
Main specifications: 200g (no weight) to 440g (full weight attached) *Weight can be changed in 40g increments, diameter 70mm, H35mm
*This is a custom-made product that is 90mm wider than SAP-1863. Since it does not come with a stand, it does not stand on its own. Sound Hunter's sound panel using cherry wood. Sound quality can be easily adjusted simply by installing it in a room. The balance between reflection and sound absorption is good, and it creates a natural spread of sound. There are tape marks on the exterior (Mizusaki Ryo)
Accessories: none
Main specifications: W720 x D50 x H1800 mm weight 13.4 kg (actual measurement)
*This is a custom-made product that is 90mm wider than SAP-1863. Since it does not come with a stand, it does not stand on its own. Sound Hunter's sound panel using cherry wood. Sound quality can be easily adjusted simply by installing it in a room. The balance between reflection and sound absorption is good, and it creates a natural spread of sound. There are tape marks on the exterior and scratches on the back (Mizusaki Ryo)
Accessories: none
Main specifications: W720 x D50 x H1800 mm weight 13.4 kg (actual measurement)
Based on the CS-1000, it is a model that promotes high sound quality and weight reduction. The duralumin machined body and Diamond Like Carbon treatment achieve both a sense of luxury and rigidity (Daiki Goto)
Maintenance information: 2024.6.5 continuity confirmed
Accessories: original box, instruction manual, screws
Main specifications: dead weight 13.7 g
SAEC ceramic shell A beryllium copper washer and a three-point crimping system are used at the arm joint. The overhang can be adjusted by means of a slide plate on the top. There is a cloudy part (Daiki Goto)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: sintered aluminum oxide body, 3-point crimping type, weight 18 g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Mizusaki Ryo)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g
*Currently sold, this is a limited edition model commemorating the 15th anniversary of the famous DL-103 cartridge. It is a step-up transformer that was sold as a set as the DL-103 T2 at the time, and it has a solid framework and a thick sound. The exterior is dull and dirty. The bottom has been replaced with felt from rubber feet (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: frequency band 20 Hz to 70 kHz 40 ohms crosstalk 60 dB or more W92 x H55 x D145 mm 720g
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. There are dirt and stain marks on the exterior (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
※It is inexpensive because it has cracks. An acoustic lens mounted on JBL monitor speakers such as the 4343 series. By wearing it, the sound of the horn, which is too strong, is moderately diffused and calmed down. There is dirt and dust on the exterior (Tamura Eiji)
Accessories: none
MC boost transformer loaded with transformers developed in collaboration with Tamura, for high impedance. Adopts a completely independent structure for the left and right, including the earth system. It matches Denon's DL-103, etc. The exterior has minor paint peeling and bumps. Serial 298 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: primary impedance 40 ohms secondary impedance 4 kΩ boost ratio 10 times W174 x H125 x D121 mm 2.5 kg
Line transformer from Uesugi Laboratory. By sandwiching it between the digital device and the amplifier, the characteristic digital noise that causes listening fatigue is removed. You can expect a change in sound quality that is familiar to the ear. It is possible to switch between 3 types of input impedances. There are scratches on the exterior. Serial 057 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: impedance compatible with 3 RCA input systems 200 ohms: 200 ohms 500 ohms: 500 ohms W175 ✕ H150 ✕ D115mm 2.5 kg
A cutting-edge unit installed in the high-end model K2 S9800. The unit alone is also highly evaluated, and it stretches flat to a very high range, and it is a dynamic sound. The exterior is good with no conspicuous scratches. Serial 01502, 010030 (Yonejima Satoshi)
Maintenance information: 2024.6.6 sweep test is good
Accessories: No accessories
Main specifications: 15inch pure pulp cone woofer with Alnico 5DG magnet 8Ω 400W playback frequency band 20Hz to 2kHz minimum resonance frequency 26 Hz 94 dB recommended crossover frequency 800 Hz outer diameter 387 mm x depth 235 mm 18 kg
LUXMAN's classic line selector. It is an easy-to-use and convenient model that outputs from 1 input system to 4 systems, and conversely, outputs from 4 input systems to 1 system. The exterior has been changed to dullness and rubber feet. Serial 20220398 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: 1 system, 4 systems input/output W160 x H65 x D95 mm, 530 g
JBL's exponential horn. Since it is a longhorn, it can be used at low crossover frequencies. Together with an acoustic lens, it is possible to create a monitor sound with high directivity. There is light rust on the mounting surface. Serial 6754/3758 (Murakoshi Yoichi)
Accessories: none
Main specifications: crossover frequency 800 Hz sound pressure level 108 dB (using 2308 lenses) throat diameter 2.5 cm diameter 156 x D 293 mm weight 1 kg/book
Maintenance has been completed, such as edge softening treatment and exterior repairs. The successor to the DS-505 with a DUD boron dome in the high range. It is a model set to be the standard for the CD era, and the sound connection between each unit is smooth, and the sense of stability in the mid to low range is attractive. You can see a feeling of use, such as appearance, dullness, corrosion, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.4 maintenance (edge softening treatment, exterior repair/cleaning)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system 6 ohms playback frequency band 30 Hz to 40,000 Hz output sound pressure level 90 dB W390 x H720 x D377 mm 33 kg
A model that inherits the lineage of 4312. The sense of speed and range has been improved with a completely renewed unit, and it has been transformed into a high-fidelity speaker that can play all kinds of sources with a clean sound with good damping. There is a light thread on the top of the exterior. Serial 13466 13432 (Murakoshi Yoichi)
Maintenance information: 2024.6.6 sound output confirmed
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex impedance 6 ohms playback frequency band 45 Hz to 35 kHz output sound pressure level 93 dB size W362 x H597 x D299 mm weight 17 kg
It was maintained in 2019. A special edition of the PM-80. A popular Marantz model from the 90s that has both luster and strength. This is a geeky model where you can enjoy the difference in tone by switching between A grade and AB grade. There is a feeling of use, dullness, and small scratches. Serial MZ009046030013 (Murakoshi Yoichi)
Maintenance information: 2019.7.11 maintenance completed (speaker relay replacement, source/TAPE switch push button SW6 wear replacement, other MM/MC switching SW/INPUT selector switch SW disassembly contact polishing cleaning, idling CLASS A · B confirmation adjustment, confirmation of solder cracks on each board, partial repair, confirmation of sound output for each input/output connection)
Accessories: instruction manual (copy)
Main specifications: AB class 100W+100W (8Ω) A grade 20W+20W (8Ω) size W454 x H165 x D380 mm weight 17.5 kg
Celestion's classic bookshelf speaker. Compared to current bookshelf speakers, the range is slightly narrower, but the mild tone with a core in the mid-range is excellent. It intensely entertains me with music. Exterior, saran net peeling, writing, dullness, scuffs, etc. can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: saran net, spike, spike receiver, instruction manual
Main specifications: 2 way 2 speakers sealed bookshelf impedance 8 ohms output sound pressure level W200 × H370 × D255 mm 8.8 kg
This is DENON's mid-range model, and is a staple machine with an excellent sense of stability, with firm bass and delicate high frequencies. In addition to the bass energy from conventional models, you can enjoy well-balanced sound that takes into account the high mid to high frequencies with a high sense of transparency. The exterior has small scratches on the top surface, back angles, etc. Serial 5061500510 (Murakoshi Yoichi)
Maintenance information: 2024.6.6 sound output confirmed
Accessories: power cord, instruction manual (copy)
Main specifications: rated output 80W+80W (8Ω) PHONO1 system (MM/MC switching) dimensions W434 x H181 x D480 mm weight 24.0 kg
Maintained! Comes with a remote control! This is a limited edition model that appeared as a gold version of the CD-94. The sound that can be heard by the combination of the CDM-1 mechanism and the TDA1541 multi-bit DAC makes me feel the high level of analog-like musicality while having a diverse amount of information. As for the exterior, there are noticeable stains and scratches on the top plate, and there are many signs of use such as dullness and scratches over time. Serial MZ02816260168 (Yamato Yuki)
Maintenance information: 2024.6.6 maintained (tray slide motor belt, CD standby motor belt, wire belt fall off replacement, repair, aging 2 days)
Accessories: remote control
Main specifications: 1 analog output, 1 digital output, 1 optical and coaxial systems, dimensions W462 x H104 x D355 mm, weight 12 kg