The price has been reduced. 2024/3/3 sales price 15,000 yen*Currently sold. Yamaha superwoofer equipped with a 20 cm x 2 double woofer. Equipped with active servo technology and a 150W high-power amplifier, it plays bass that is small yet full of volume. There is dirt, dirt and dullness on the exterior, and some floating on the bottom. Serial Z117079QS (Tamura Eiji)
Maintenance information: 2024.3.3 sweep test is good
Accessories: No accessories
Main specifications: used unit 20 cm cone type x 2 rated output 150 W (5 Ω) playback frequency band 20 Hz to 160 Hz high cut filter 40 Hz to 140 Hz, continuously variable W235 x H602 x D463 mm 20 kg
※Since it is inexpensive, it will be handed over as is. Tamban 10cm full range unit. An ultra-thin PP diaphragm with reinforced ribs is used. The sound is clear and crisp. A 6-8 liter bass reflex box is recommended (Tamura Eiji)
Maintenance information: 2023.10.1 sweep check OK
Accessories: none
Main Specifications: Rubber Edge Impedance 4 Ohms Sound Pressure Level 87 dB Frequency Band 63 to 17,000 Hz Maximum Input 40 W Baffle Aperture Diameter 94 mm Weight 380 g
Line transformer from Uesugi Laboratory. By sandwiching it between the digital device and the amplifier, the characteristic digital noise that causes listening fatigue is removed. You can expect a change in sound quality that is familiar to the ear. It is possible to switch between 3 types of input impedances. There are scratches on the exterior. Serial 057 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: impedance compatible with 3 RCA input systems 200 ohms: 200 ohms 500 ohms: 500 ohms W175 ✕ H150 ✕ D115mm 2.5 kg
MC boost transformer loaded with transformers developed in collaboration with Tamura, for high impedance. Adopts a completely independent structure for the left and right, including the earth system. It matches Denon's DL-103, etc. The exterior has minor paint peeling and bumps. Serial 298 (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: primary impedance 40 ohms secondary impedance 4 kΩ boost ratio 10 times W174 x H125 x D121 mm 2.5 kg
Hi-Fi's first Trilogue series subwoofer has arrived! Not only for those using the Trilogue speaker, it also demonstrates sufficient performance as a standalone unit. This one is not compatible with spikes. The exterior has dullness and scratches. Serial 30-07-00 (Tamura Eiji)
Maintenance information: 2024.5.30 Operation confirmed
Accessories: power cable, saran net, original box
Main specifications: built-in power amplifier, 2 speakers, bass reflex, built-in power amplifier output, 200W, high frequency cutoff frequency 40/50/60hz, W380 x H540 x D650 mm, weight 45 kg
Hi-Fi's first Trilogue series subwoofer has arrived! Not only for those using the Trilogue speaker, it also demonstrates sufficient performance as a standalone unit. This is a spike specification. There are wrinkles on the exterior like wrap marks. Serial 30-07-00 (Tamura Eiji)
Maintenance information: 2024.5.30 Operation confirmed
Accessories: power cable, saran net, original box
Main specifications: built-in power amplifier, 2 speakers, bass reflex, built-in power amplifier output, 200W, high frequency cutoff frequency 40/50/60hz, W380 x H540 x D650 mm, weight 45 kg
Line matching transformer sold 1 piece Primary: 600 Ω - CT Secondary: 600 ohms Output 10 dBm Frequency Range 50 to 10 kHz W44 x H65 mm 0.25 kg/piece There are bumps and paint peeling in places (Yosuke Kojima)
Accessories: none
* Since there are difficulties with the attachment part on both sides, it is inexpensive. Line matching transformer sold primary: 600 ohms, output 10 dBm, frequency range, 50 to 10 kHz, W44 x H65 mm, 0.25 kg/piece, the head of the mounting bolt on one side is flying off, and there is distortion in the screw hole on the other side (Kojima Yosuke)
Accessories: none
Line matching transformer sold 1 piece Primary: 600 Ω Secondary: 600 Ω Winding Ratio 1:1 Output 10 dBm Frequency Range 50 to 10 kHz W34 x H42 x D22 mm Approx. 0.1 kg (Yosuke Kojima)
Accessories: none
Wood cabinet for TD-124 of unknown manufacturer. It can be equipped with an SME long arm. The exterior has scratches, threads, chips, etc. (Tamura Eiji)
Accessories: no accessories
Main Specifications: W597 ✕ H160 ✕ D445mm Weight 3.9 kg
SAEC long-selling model with a 0.6 m digital cable. 6N ultra-high purity copper with excellent transmission characteristics is used as the conductor material, and transmission loss is reduced with accurate impedance matching (Tamura Eiji)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
※Since it is cheap, it will be handed over as is. Comes with a remote control. AM/FM stereo tuner with dual-gate MOS FET on the front end. The tone is bright and natural. There are dirt scratches and threads on the exterior. Serial MZ009520050055 (Tamura Eiji)
Maintenance information: 2024.6.5 operation confirmed
Accessories: remote control, instruction manual, AM antenna
Main specifications: AM/FM stereo synthesizer tuner dimensions W428 x H86 x D295 mm weight 3.2 kg
YAMAHA speaker stand The compact stand is made to feel stiff, and you can expect tight sound quality. It can be used for small speakers such as the NS-10M and medium speakers. There are line marks, threads, and tape marks on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: W270 x H494 x D350 mm top plate part W190 W x D175 mm 7 kg/unit
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
The 1.2m pair of unprocessed speaker cable has excellent balance from low to high frequencies, and has an energetic and warm tone. There are threads and disappearing characters on the exterior (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: No accessories
line harmonizer. Sound quality improvement item by using 10 ferrite cores in series. It has the effect of reducing noise and improving sound quality (Tamura Eiji)
Maintenance information: 2024.6.9 operation confirmed
Accessories: case, instruction manual
A record player equipped with a Bluetooth (R) function and a USB output terminal. It can be connected to a Bluetooth (R) compatible wireless speaker, etc., and is recommended for those who want to enjoy a record player casually. As for the exterior, there is a thread on the dust cover. Serial 1007740 (Tamura Eiji)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: AC adapter, EP adapter
Main specifications: W516 × H198 × D433m mass 5 kg
It's a small digital interface that fits in the palm of your hand. The input uses a Type-C USB interface. The output is I2S/optical/coaxial. The sampling rate is PCM32 bit/768 kHz compatible, DSD native, DOP64 compatible (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: original box, connection cable
Main specifications: W80 x H13 x D60 mm dead weight 120 g
Unused item! Power transformer primary: 90-100-110V secondary: 6.3V/3A x 2, 400-325-0-325-400V/230mA, 5V/3A W122 x H150 x D102 mm 5.4 kg (actual measurement) (Kojima Yosuke)
Accessories: none
* It seems to be an output transformer from the specifications; sold 1 piece, primary: 10 kΩ, secondary: 600 ohms, W76 x H71 x D43 mm, 0.6 kg (actual measurement, not including protrusions), there is paint peeling in places (Kojima Yosuke)
Accessories: none
Output transformer sold 1 piece Primary: 14 kPPΩ Secondary: 600 Ω WW76 × H71 × D43 mm 0.6 kg (actual measurement, protrusions not included) There are paint peeling and seal marks in places (Kojima Yosuke)
Accessories: none
※Since it is cheap, it will be handed over as is. A mixer with an effect loop that can mix 3 channel inputs (microphone or line) and 3 stereo line systems. The exterior has dullness and scratches. Serial M1007000864 (Tamura Eiji)
Maintenance information: 2024.5.19 simple check OK (details will not be checked)
Accessories: No accessories
Main specifications: W483 x H44.5 x D152 mm weight 2.8 kg
A speaker stand with a height of about 20 cm. It is recommended for those who want to build a desktop or compact audio system. The exterior has dullness and small scratches (Tamura Eiji)
Accessories: No accessories
Main specifications: top plate 240 x 210 mm thickness 2.3 mm bottom plate 240 x 210 mm thickness 2.8 mm load capacity 12 kg size W210 x H206 x D 240 mm weight 2.2 kg
The disposal price has been reduced! Member prices are not applicable. 2024/3/22 sales price 29,800 yen The tuning hole uniquely arranged on Oyaide's turntable plate thoroughly eliminates unnecessary vibrations that disrupt the record board's trace, and furthermore, when used in combination with a stabilizer, the warpage of the record board is corrected and appropriate traces can be expected. There are small scratches and dullness on the exterior (Tamura Eiji)
Accessories: instruction manual, original box
Main specifications: dimensions: 294 mm, thickest part: 5 mm, 670 g
※Since it is cheap, it will be handed over as is. 1 bottle only 25cm full range speaker made by RCA in the USA. The Alnico magnet responds well and the sound is easy to remove. There are repair marks on the edge (Tamura Eiji)
Maintenance information: 2024.3.22 sweep test good
Accessories: No accessories
Key Specifications: Unit Diameter 25cm 8Ω Fixed Edge
Line noise filters. An accessory that thoroughly eliminates transient distortion generated within line cables and improves overall signal-to-noise ratio. Sounds that could not be heard until now appear clearly, and it becomes a dynamic playback sound that stretches and stretches from low to high frequencies (Tamura Eiji)
Maintenance information: 2024.6.9 operation confirmed
Accessories: none
Main specifications: Input side: RCA jack Output side: RCA pin plug
Maintained! Comes with a remote control. A CD player developed to commemorate the 100th anniversary of Philips's founding. The sound is soft and relaxed, and the thickness of the analog-like mid-low range is particularly irresistible. A swing-arm CDM-4 mechanism is used for the mechanism part, and TDA1547 (DAC7) is used for the D/A conversion part to achieve advanced S/N improvements. As for the exterior, there are bald spots and stains on the SW area. MZ019204080075 (Tamura Eiji)
Maintenance information: 2024.6.9 Maintained (both tray slide belt and CD standby motor belt replaced. Other CD mechanisms, drive circuit check, reading check OK, remote control check OK)
Accessories: remote control, lock pin
Main specifications: CDM-4 mechanical DAC7 equipped analog output 2 systems (XLR/RCA) 2 digital output systems (optical/coaxial) W457 x H140 x D359 mm 16.7 kg
The HDMI cable is a 3.0 m high-grade connector, and a nylon mesh cable is used for the outer shell. It is possible to faithfully transmit high quality video and sound (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: none
It is a USB-connected bus-powered D/D converter that uses the C-Media “CM6642” as the digital audio control IC and is compatible with high-resolution sound sources (maximum 24 bit/192 kHz) (Tamura Eiji)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, original box
Main specifications: digital input: USB TypeB terminal USB 1.1/2.0 compatible, USBAudioClass 1.0/2.0 compatible digital output: coaxial digital audio output (COAXIAL) optical digital audio input (square) compatible format: PCM maximum 24 bit 192 kHz W40 x H25 x 81 mm 90 g
A rare FR dynamic balance type long arm, which has not arrived in a long time, has arrived! Dynamically balanced Roman arms. It uses a central mass concentration structure and a differential damping mechanism to produce precise and accurate sound. *Phono cable is missing. Serial 161934 (Tamura Eiji)
Maintenance information: 2024.5.29 continuity confirmed
Accessories: original box, instruction manual
Main specifications: Long arm dynamic balance needle pressure range 0 to 3 g total length 379 mm effective length 307 mm overhang 12 mm compatible cartridge 17 to 32 g arm height 36 to 72 mm
The disposal price has been reduced! (Member prices are not applicable) 2024/4/28 sales price 99,800 yen D/A converter with a dual monaural configuration equipped with 2 “ES9038PRO” units. Using 3 Talema toroidal transformers, you can feel the creator's commitment. More natural sound can be reproduced. On the exterior, there are noticeable line marks on the top plate (Tamura Eiji)
Maintenance information: 2024.4.28 Operation confirmed
Accessories: No accessories
Main Specifications: Coaxial/BNC/AES/Optical: PCM44.1k to 192 K/16 to 24 bit, DOP64 I2S Input: RJ45/HDMI PCM44.1K to 768K 24/32 bit DSD64 to DSD1024 DOP64 to 256 W430 x H80 x D335 mm Weight 5.4 kg
For the first time in about 8 years, Mysonic Labs ultra-low impedance mono MC cartridges have arrived! It is a cartridge designed to extract as much information as possible from mono LPs. Even though it's clear, you can feel the richness of the relaxed sound, and it makes me reaffirm the goodness of mono LPs. Serial A577 (Tamura Eiji)
Maintenance information: 2024.6.1 operation confirmed
Accessories: instruction manual, original box, needle cover, brush
Main specifications: Ultra low impedance MC cartridge frequency range 10 Hz to 50 kHz output voltage 0.4 mV impedance 1.2 Ω needle pressure 3 g
Dayton Audio's small power amplifier. Designed to be just the right size for a desktop, this is one that can be loud enough for a small speaker. It also has a headphone jack, so it can also be used as a headphone amplifier. The exterior is dull. Serial V200004300 (Tamura Eiji)
Maintenance information: 2024.5.30 Operation confirmed
Accessories: AC adapter
Main specifications: 60W+60W (4Ω) W117 x H44 x D79 mm dead weight 1.23 kg
Exclusive stand for the DS-77HR sold separately. Of course, it is also recommended for other medium speakers. The exterior has creases, floats, scratches, etc. (Tamura Eiji)
Accessories: No accessories
Main specifications: W410 x H264 x D330 mm weight 10 kg
The 0.5 m HDMI cable connector is made of high-grade aluminum material, and the outer skin of the cable uses a slim nylon mesh cable that can be wired neatly and is less burdensome when bending. Compatible with 4K2K (60P), it is possible to faithfully transmit high quality video and sound (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: case
The price has been reduced! 2024/5/16 The CD mechanism has been replaced with Denon at a sales price of 35,000 yen! Denon design series CD player. It is equipped with an inexpensive yet highly accurate D/A converter that is compatible with MP3 and WMA files. Since it can also be used vertically, it is attractive that it is easy to adjust where it is placed. The exterior is dull and has small scratches. Serial ADR 27190603014 (Tamura Eiji)
Maintenance information: 2024.5.16 manufacturer maintained
Accessories: remote control, power cable
Main specifications: analog output x 1, coaxial digital output x 1 size W200 x H86 x D 240 mm, weight 2.4 kg
The disposal price has been reduced! (Member price not applicable) 2024/5/24 sales price 128,000 yen A digital amplifier equipped with a Tripath class T PWM amplifier IC. It beautifully expresses the sense of energy and description. Gain can also be switched on the back, and it is compatible with a wide range of input sources. On the exterior, there are oxidation and scratches on the manufacturer logo. Serial 100210015 (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: instruction manual, power cable, spike
Main specifications: output 150W+150W (8Ω) 240W+240W (4Ω) W420 x H98 x D395 mm weight 13 kg
Mini plug to stereo standard plug conversion cable It is a model using OFC as a wire rod. (Eiji Tamura)
Maintenance information: 2022.1.5 continuity confirmed
Accessories: original box
The price has been drastically reduced! 2024/4/27 sales price 79,800 yen Maintained! This is the first AUDIO OF OREGON control amplifier to arrive in a long time. It is compatible with 117V specification American speakers such as ALTEC and JBL, etc., and although it is a transistor, it doesn't become too stiff and makes you enjoy the firm sound. The exterior has dullness and scratches. ※The plug has been changed. Genuine RF Serial 02117 (Tamura Eiji)
Maintenance information: 2024.4.27 Maintained (no running symptoms. The board vibration check connection was checked. (All pattern parts of the flat amplifier module unit have been added and soldered.) 2024.4.13 Maintained (Electrolytic capacitor replacement in amplifier module. Pattern contact defect correction. (Voice operation check)
Accessories: No accessories
Main specifications: All stages use pure class A operation circuit input phono (mm/47 kΩ) tuner, tape, aux dimensions W483 x H89 x D190 mm weight 4.5 kg
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. There are dirt and stain marks on the exterior (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
*Currently sold, this is a limited edition model commemorating the 15th anniversary of the famous DL-103 cartridge. It is a step-up transformer that was sold as a set as the DL-103 T2 at the time, and it has a solid framework and a thick sound. The exterior is dull and dirty. The bottom has been replaced with felt from rubber feet (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: frequency band 20 Hz to 70 kHz 40 ohms crosstalk 60 dB or more W92 x H55 x D145 mm 720g
Set of 4 Audio-Technica banana plug Insert the core wire of the cable that has been coated by about 5 mm beforehand, fold the tip back, tighten it back, and fix the cable firmly before use (Tamura Eiji)
Accessories: none
Set of 4 Technica's classic banana plug. Insert the core wire that has been stripped of the cable coating into the hole on the side of this product, tighten the product back and fix the cable (Tamura Eiji)
Accessories: none
Set of 4 Technica's classic banana plug. Insert the core wire that has been stripped of the cable coating into the hole on the side of this product, tighten the product back and fix the cable (Tamura Eiji)
Accessories: case
Set of 4 Technica's classic banana plug. Insert the core wire that has been stripped of the cable coating into the hole on the side of this product, tighten the product back and fix the cable (Tamura Eiji)
Accessories: case