Oyaide record stabilizer. The vibration mode is optimized with a hybrid configuration of aluminum, brass, and texalum. Unnecessary vibrations associated with platter rotation are attenuated, and sound groove tracing is dramatically improved. It can also be used as an EP stabilizer by reversing it up and down (Daiki Goto)
Accessories: original box, instruction manual
Main specifications: 200g (no weight) to 440g (full weight attached) *Weight can be changed in 40g increments, diameter 70mm, H35mm
*This is a custom-made product that is 90mm wider than SAP-1863. Since it does not come with a stand, it does not stand on its own. Sound Hunter's sound panel using cherry wood. Sound quality can be easily adjusted simply by installing it in a room. The balance between reflection and sound absorption is good, and it creates a natural spread of sound. There are tape marks on the exterior (Mizusaki Ryo)
Accessories: none
Main specifications: W720 x D50 x H1800 mm weight 13.4 kg (actual measurement)
*This is a custom-made product that is 90mm wider than SAP-1863. Since it does not come with a stand, it does not stand on its own. Sound Hunter's sound panel using cherry wood. Sound quality can be easily adjusted simply by installing it in a room. The balance between reflection and sound absorption is good, and it creates a natural spread of sound. There are tape marks on the exterior and scratches on the back (Mizusaki Ryo)
Accessories: none
Main specifications: W720 x D50 x H1800 mm weight 13.4 kg (actual measurement)
Based on the CS-1000, it is a model that promotes high sound quality and weight reduction. The duralumin machined body and Diamond Like Carbon treatment achieve both a sense of luxury and rigidity (Daiki Goto)
Maintenance information: 2024.6.5 continuity confirmed
Accessories: original box, instruction manual, screws
Main specifications: dead weight 13.7 g
SAEC ceramic shell A beryllium copper washer and a three-point crimping system are used at the arm joint. The overhang can be adjusted by means of a slide plate on the top. There is a cloudy part (Daiki Goto)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: sintered aluminum oxide body, 3-point crimping type, weight 18 g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Mizusaki Ryo)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g
*Currently sold, this is a limited edition model commemorating the 15th anniversary of the famous DL-103 cartridge. It is a step-up transformer that was sold as a set as the DL-103 T2 at the time, and it has a solid framework and a thick sound. The exterior is dull and dirty. The bottom has been replaced with felt from rubber feet (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: frequency band 20 Hz to 70 kHz 40 ohms crosstalk 60 dB or more W92 x H55 x D145 mm 720g
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. There are dirt and stain marks on the exterior (Tamura Eiji)
Maintenance information: 2024.6.6 operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
※It is inexpensive because it has cracks. An acoustic lens mounted on JBL monitor speakers such as the 4343 series. By wearing it, the sound of the horn, which is too strong, is moderately diffused and calmed down. There is dirt and dust on the exterior (Tamura Eiji)
Accessories: none