Replacement needle compatible with National EPS-19ST Operation has not been confirmed since there is no main unit (Hiura Katsuji)
Maintenance Information: Operation Unconfirmed
Accessories: original box
4530BK made by Shinkosha. Since there are many chips and scratches throughout, it is inexpensive. The D130 was mounted. Woofer with MA15 fastener! Powerful bass reproduction far exceeding size is possible with the rear loading horn type enclosure (Sasaki Shota)
Accessories: MA15
Main specifications: screw pitch 420 mm hole diameter 360 mm plate thickness 40 mm front baffle plate thickness 22 mm W600 x H1250 x D600 mm 56.3 kg (all measured)
Tannoy rectangular yoke type enclosure by Shinkosha, a popular domestic box manufacturer. It is attractive because it is made to sound good. A 30cm unit adapter (detachable) is attached to the baffle surface, and casters are attached to the bottom (Murakoshi Yoichi)
Accessories: none
Main specifications: W597 x H108 x D37 mm weight 30 kg
Self-made enclosure. The woofer opening is about 340 mm in diameter, the horn opening above it is 450 mm x 266 mm, the upper opening is 260 mm x 134 mm, and the tweeter part is about 60 mm in diameter. Shipping costs will be estimated separately (Oikawa Tetsuji)
Accessories: none
Main specifications: plate thickness 25 mm W800 x H960 x D580 mm 54.1 kg (actual measurement)
A 38cm double configuration enclosure that can be used as a center woofer or center speaker. The previous owner had an electro voice 38cm woofer installed. Comes with casters. There is a lot of feeling of use, such as uneven paint and bolt marks on the top plate. Please contact us for shipping (Murakoshi Yoichi)
Accessories: none
Main specifications: W1045 x H790 x D604 mm 52.2 kg
A self-made large record player cabinet where Victor's TT-101 was mounted. SAEC's WE-308SX was mounted on the arm. Shipping costs will be estimated separately (Sasaki Shota)
Accessories: none
Main specifications: W630 x H205 x D570 mm, arm hole diameter 43/29 mm, weight 26.2 kg
The disposal price has been reduced! Member prices are not applicable. 2022/7/16 selling price 100,000 yen wooden 46cm double woofer type. Baffle opening diameter 425mm Screw pitch 490mm Baffle and enclosure plate thickness 24mm Duct opening diameter 108mm Both the front and back plates cannot be removed. There is a difference in discoloration on the left and right in appearance, and there are corner chips, digging scratches, and dirt stains. (Yutaka Takimoto)
Accessories: none
Main specifications: W1600 × H950 × D850 mm (actual measurement) The weight has not been measured, but it seems that it is 100 kg or more.
A self-made record cleaner that imitates PAROSTATIK. The core inside is a vinyl sheet wrapped around it. Thanks to the soft core, it is exquisitely comfortable to use. The exterior has a frayed feeling of use (Katsuji Hiura)
Accessories: none
Main specifications: W105mm diameter 30mm weight 9g
A FOSTEX HA21 throat adapter is set on a self-made horn that is a size imitation of the FOSTEX H320. If you've been looking for this size, take this opportunity! You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: throat diameter 100 mm pitch 4 holes 60 mm 3 holes 50 mm overall W635 x H110 x D 455 mm kg (actual measurement)
The price has been reduced! 2023/10/7 This is a self-made MC step-up transformer with a sales price of 20,000 yen. According to the specifications, the boost ratio appears to be 1:10. Use it with high output cartridges such as the DL-103! (FUJISAWA KOSHI)
Maintenance information: 2023.10.7 operation confirmed
Accessories: none
Main specifications: MC boost transformer input/output 1 system boost ratio 1:10 W 110 x H45 x D145 mm (actual measurement)
Inexpensive because it is in poor condition. 38cm enclosure. Originally, the ALTEC 604-8G was included. There are many scratches, cracks and peeling on the decorative plate, and there is screw licking*Shipping is estimated separately (Oikawa Tetsuji)
Main specifications: W660 x H1005 x D465 mm 35.1 kg
Self-made enclosure. The previous owner attached a JBL 38cm unit with a 1" driver and used it in 2 ways. It comes with casters. There is a lot of feeling of use, such as uneven paint. Please contact us for shipping (Murakoshi Yoichi)
Accessories: none
Main specifications: W500×H790×D604mm 53.4 kg
Self-made 4ch power amplifier using 4 Flying Mall digital power amplifiers DAD-M1. The construction is solid, and the sound is high resolution, just like a flying mall. Recommended for those who want to save space and use it for multiple purposes. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.20 sound output confirmed
Accessories: power cable
Main specifications: DAD-M1 rated output 160W/4Ω 100W/8Ω frequency characteristics DC to 25kHz/4Ω DC to 50kHz/8Ω S/N ratio 120dB overall size W270 × H162 × D290 mm weight 6 kg (actual measurement)
The price has been reduced. 2020/4/17 Selling price 5,000 yen Unspecified wooden front baffle. If you are a self-made group, come on. There are scratches and stains scattered, uneven painting, corner chips, etc. (Takasaki Atsushi)
Accessories: none
Main specifications: opening diameter 280 mm bass reflex opening W292 × H80 mm W400 × H610 × D20 mm 1.8 kg/sheet
Self-made cabinet for GARRARD 301 with double arm specifications. The 3012 Series 2 and SMG-212 were mounted on the tone arm installation port. You can see the appearance, peeling veneer, abrasions, bruises, etc., and a feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: W760 x H265 x D520 mm 14.4 kg (actual measurement)
Unspecified 3-way enclosure It is a super bargain price with a considerable feeling of use. For experimentation or research, if you are a self-author with confidence in your arm, how about challenging it? (Yoichi Murakoshi)
Main Specifications: W648 x H967 × D457mm 36.8 Kg (Measurement) Woofer opening diameter 300 mm Scoker opening diameter 173mm tweeter opening diameter 102mm
1 pair of unspecified speaker stands Attention can also be seen, such as constructing a metal circular insulator. If you've been looking for this size, go for it. The exterior, paint unevenness, dullness, abrasions, etc. can be seen a lot of feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: W450 x H240 x D450 mm 12 kg (actual measurement)
The disposal price has been reduced. Member discounts are not applicable. 2024/2/22 sales price 8,000 yen. Self-made cabinet for DENON DP-3000. The arm was attached to the company's DA-305. When the four-square screw is removed, it is divided into 3 plates, making it easy to perform processing such as drilling. There are scratches, fading, stains on the main body, cracks, repairs, fading, stains, and adhesive tape marks on the dust cover (Kanai Hidetsugu)
Accessories: dust cover
Main specifications: W600 x H112 (H202 with dust cover) x D500 mm 12.6 kg (actual measurement, dust cover included)
Self-made 4ch power amplifier using 4 Flying Mall digital power amplifiers DAD-M1. The construction is solid, and the sound is high resolution, just like a flying mall. Recommended for those who want to save space and use it for multiple purposes. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.20 sound output confirmed
Accessories: power cable
Main specifications: DAD-M1 rated output 160W/4Ω 100W/8Ω frequency characteristics DC to 25kHz/4Ω DC to 50kHz/8Ω S/N ratio 120dB overall size W270 × H162 × D290 mm weight 6 kg (actual measurement)
Tokyo soundproof turntable seat using vibration-absorbing rubber. The vibration convergence time is overwhelmingly fast, and it effectively absorbs unwanted vibrations in the frequency band that is important for music playback. (FUJISAWA KOSHI)
Accessories: case
Main specifications: size 4 mm thick x 291 mm diameter weight 330 g
Variable Resistor Attenuator Bridge T Type 21 Steps Maximum Attenuation 50 dB Impedance 600 Ohms W45 x 64 mm 140 g with Volume Knob (Kojima Yosuke)
Accessories: volume knob (attached to the main unit)
One-piece rectifier tube, fishing rod type filament made in China, incorporates the structure of the original WE274 and is well-built. Measurement value 56 (rejected value 40) with replacement box ※ The measured value shows the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
TRIO N-39 compatible needle. This is a replacement needle for TRIO V-39. Operation not confirmed (Murakoshi Yoichi)
Maintenance information: operation unconfirmed
Accessories: original box
Set of 4, 32 mm diameter pinpoint base made of African ebony used for oboes, etc. Sound quality can be improved by itself or combined with the PB-10 and placed under a speaker or amplifier. The exterior has a feeling of use such as dullness and scratches (Jun Tamai)
Accessories: original box
Main specifications: load capacity 50 kg (4 pieces) body height 19 mm spike height 5 mm