The price has been drastically reduced! 2024/3/28 sales price 398,000 yen Electric has been maintained, including replacing a new windshield panel! A pre-main amplifier with a built-in McIntosh traditional output transformer. You can enjoy the rich and rich sound world typical of Macintosh. This is one that combines the appeal of the sounds of modern and old McKinn. The sense of power that makes you feel the strength is similar to that of a separate amplifier. The exterior is dull. Serial JLF1440 (Fujisawa Yukishi)
Maintenance information: 2024.4.24 Manufacturer maintained (various solder fixes on the driver board. windshield panel replacement Switch bezel fixing O ring replacement IC exchange. Capacitors were replaced at various other locations. Filter capacitor replacement. Other relays, transistors, etc. have been replaced, but please note that the pop noise of this unit is difficult to completely remove due to product specifications, so it can be heard slightly depending on when the power is turned on. Replace all front lamps. Lamp fixing grommet replacement There is a difference in meter runout when the volume is low, but when the output is raised by about 3/4, the difference is not very noticeable. Due to specifications due to individual differences in parts, improvements are difficult, so adjustments were made so that they fit at a position of approximately half a meter. Same confirmation and other inspections. *The VOL position is 05, which is the normal level of around 9 o'clock, but this is a specification. (If you are concerned, lower the CD level.)
Accessories: remote control, instruction manual
Main specifications: 150W+150W (8/4/2Ω) phono input MM dimensions W445 x H179 x D508 mm weight 30 kg
The price has been reduced! 2024/3/15 sales price 79,800 yen 2023/11 maintenance completed! The middle class of the Sansui α series. The strength of the bass and the sharpness of the mid to high notes are mixed in a well-balanced manner, so you can enjoy not only jazz, but also various genres such as rock and pop music. The exterior is dull and the top plate is damaged. Serial 637065630 (Tomonori Asaine)
Maintenance information: 2023.11.23 Maintained (disassembling and polishing grease applied to each switch (tone, turnover, loudness, muting, subsonic, power amplifier direct, MM/MC, reckout switch), each volume and switch clean output relay and headphone relay replacement main amplifier and power supply part solder repair, interior and exterior inspection, cleaning, side cover screw replacement operation confirmation when power is turned on It makes a popping sound, but it stabilizes in a few minutes)
Accessories: copy of instruction manual
Main specifications: effective output 160W+160W (6Ω) 130W+130W (8Ω) damping factor 100 (6Ω) W448 × H160 × D441 mm 20.3 kg
The price has been drastically reduced. 2024/4/22 sales price 128,000 yen Maintained! A famous machine 44 with an easy-to-handle RCA terminal added to the rear terminal of the Quad control amplifier. The British QUAD's small preamp is a perfect balance between the freshness and richness of character. You can enjoy a calm, high-quality sound when paired with the same speakers made in England (Murakoshi Yoichi)
Maintenance information: 2024.4.18 maintenance (internal all checks, power supply filter C ± B bypass C replacement, balance VOL cut off sound → cleaning, check each board)
Accessories: 2 DIN input cords, power cord, instruction manual (copy)
Main specifications: 2 LINE inputs, 2 TAPE2 systems (DIN input or more), 1 PHONO input system, Phono sensitivity 1m/3m/10mV switching W321 x H103 x D203 mm 4 kg
Maintenance is being carried out in 2020. It's a famous machine you can't miss when talking about Marantz sounds of yesteryear. It has a good mid-range fat transfer, and its pleasant tonal feel is an appeal that cannot be obtained anywhere else. You can enjoy the Marantz sounds of the good times. There is some rust and small scratches on the exterior. Serial 8-4160 (Murakoshi Yoichi)
Maintenance information: 2020.11.18 maintained (AC code deterioration exchange, 40/40/20 μF and other deterioration replacement, 3 external paint, 20 μF x 2 deterioration exchange, selenium deterioration countermeasures → diode addition · vacuum tube 6BH6 noise exchange · vacuum tube socket and RCA jack caulking repair ※ other operation checked (measured at 32 to 41 W SP: 8 Ω with rated output AC 100 to 117 V) *A2 The EL34 vacuum tube guide pin is broken, but there is no problem with performance. (Part of the SP terminal on the right channel is missing.)
Accessories: instruction manual (for replicas, Japanese copy)
Main specifications: 35W+35W vacuum tube 6CG7/6BH6/EL34 W348 × H191 × D273mm 22.5 kg
High output MC cartridge for mono LPs only. Plays deep sound that was not produced with stereo cartridges. It has the vividness unique to Technica, but the three-dimensional effect and intensity are an appeal unique to mono (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: needle cover
Main specifications: high output MC type output 1.2 mV needle pressure 2.0 g impedance 40 ohms dead weight 6.8 g
original needle. It combines the delicate expressive power unique to light needle pressure with an energetic, thick sound typical of Type 3. Recommended for those who listen to jazz and rock (Sasaki Shota)
Maintenance information: 2024.4.25 Sound output operation confirmed
Accessories: none
Main specifications: mm type frequency range 10 Hz to 25,000 Hz output voltage 3.5 mV needle pressure 0.75 g to 1.25 g weight 6 g
Comes with original box SPU synergy with the highest output in the SPU lineup. Using a G-shell containing neodymium magnets and zinc powder, it combines a modern, energetic sound with a rich sound typical of an orthophone. The stylus is good (Sasaki Shota)
Maintenance information: 2024.4.25 Sound output operation confirmed
Accessories: original box
Main specifications: MC type output voltage 0.5 mV diamond oval needle frequency characteristics 20 to 20,000 Hz needle pressure 3 g dead weight 30 g
This model commemorates the 250th anniversary of J.S. Bach's death. Uses a 6N silver wire coil. It is a cartridge that excels in even more delicate spatial expression while retaining the feel of an orthophone. The know-how of the masterpiece Jupiter has been fully introduced, and the high cost performance stands out. The cantilever is slightly to the right, and there is a small scratch and dullness on the body (Sasaki Shota)
Maintenance information: 2024.4.25 Sound output operation confirmed
Accessories: nothing
Main specifications: output voltage 0.45 mV frequency characteristics 20 Hz to 35 kHz internal resistance value 5 ohms, suitable elliptical needle pressure 2.5 g, dead weight 10 g
※The nail on the needle cover is broken, so it cannot be locked. This is BLUE from the 2M series. Ortofon's popular series with a wide range and vibrant sound. It makes you enjoy sharp sounds from popular to jazz (Hiroki Aso)
Maintenance information: 2024.4.25 storefront operation confirmed
Accessories: original box
※Since the cantilever is slightly raised, it is inexpensive. Mid-range models in the MC Star series, which come in 3 types. Both models have different sounds, and they are all unique, but 20W is a model that places particular emphasis on the mid-range. The sound is warm in tone, and has an extrusive, and comfortable sound that goes through the SPU. The wooden body made of Yamanaka lacquer, which is a traditional Japanese craft, is also beautiful.
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: MC type output voltage 0.5 mV suitable needle pressure 2.3 g recommended load impedance 10 to 200 ohms dead weight 10.5 g
A head shell with a round tip that matches the MC Jubilee and Kontrapunkt cartridge shapes. Its own weight is 14.6g, which is a bit heavy (Yasuhito Koshihama)
Main specifications: machined aluminum block, dead weight 14.6 g
Denon's classic shell. This is a genuine DA-305 shell. There is plenty of room around the lead wire, and various cartridges can be attached (Oikawa Tetsuji)
Accessories: none
Main specifications: dead weight 7g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Sasaki Shota)
Accessories: none
Main specifications: aluminum stamping dead weight 8g
It is a model designed to further enhance the results of the regular type, with the main focus on thoroughly eliminating sound quality deterioration factors such as mechanical vibration and electrical vibration. 4-tier rack for analog players with decoupler The exterior has dullness and scratches (Satoshi Yonejima)
Accessories: No accessories
Main specifications: shelf size/1st tier 160mm/ 2nd tier 180mm/ 3rd tier 60mm W600 ✕ H540 ✕ D475mm 8.8 kg
*Currently sold. This is an AUDIO PHYSIC superwoofer. You can enjoy very powerful bass. The crossover can also be switched between 32/46/61/80/105 Hz, which is convenient. As for the exterior, there are line scratches, saran net holes, dull stains, etc. on the top plate. Serial 573 (Yonejima Satoshi)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: spikes, saran net
Main specifications: W260 x H625 x D400 mm 26 kg
Technics machined aluminum EP adapter It's a convenient item to have for listening to singles. There is a feeling of use such as dullness (Hiroki Aso)
Accessories: none
The core model for Marantz SACD players. Although it is an entry model, it has a high S/N feel typical of the company's products, and the sound quality is excellent for listening for a long time. It is an attractive player with a sense of quality in the mid to high range with a fine particle feel. The exterior has a feeling of use such as dullness and small scratches. Serial 20000540002323 (Takahashi Nobuyuki)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: remote control instruction manual power cable
Main specifications: SACD/CD player, 1 analog output system (RCA), 2 digital output systems (coaxial x 1, optical x 1), digital filter, switch to 3 modes, W440 x H123 x D419 mm, 13.5 kg
The original appeal of Arden, where a simple, beautiful design and deep sound coexist with full internal and external maintenance utilizing original capacitors, has been revived. This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. The sense of scale of the orchestra and the smooth playback of stringed instruments are satisfying enough to listen to. There are repair marks on the edge of the cone paper on one side and the top surface on one side. The exterior has been beautifully finished due to exterior maintenance. Serial 0016190/0005927 (Murakoshi Yoichi)
Maintenance information: 2024.4.3 maintenance (exterior repair) 2022.5.30 maintained (output terminal contact cleaning. Chassis screw replacement. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (low range side: edge replacement, magnetic circuit rust removal/gap cleaning/center adjustment, high range side: magnetic circuit rust removal/gap cleaning/center adjustment. Exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement. (Detachable unit)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
※ Sub weight is missing. A long-selling player that Technics is proud of. It boasts a simple design that is easy to use, stable operation, and durability. Clear contours, high earthquake resistance, highly accurate tone arms, etc., all of these are attractive cars with a degree of perfection that exceeds the price. Exterior, slight small scratches, abrasions, etc. can be seen (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: dust cover
Main specifications: Quartz control direct drive system speed 33.45 rotation speed fine adjustment range ± 8% (continuously variable) W453 x H162 x D360 mm approx. 12.5 kg
The price has been drastically reduced! 2024/4/20 sales price 330,000 yen Maintained! 100V specification genuine Baes product. A power amplifier representing the McKinn Golden Age. It has a rich, gorgeous sound with a punch, and is still a popular model. Although it is a transistor amplifier, it is an amplifier that still has a strong tubular atmosphere. The rich, thick characters reproduce the music on a rich scale. Rust can be seen on the main body. Serial JCT1245 (Fujisawa Yukishi)
Maintenance Information: 2024.4.8 Maintained (Electrolytic Capacitor Replaced. Replace the meter and display lamp. Apply heat-resistant tape. Urethane sheet deterioration replacement. Clean switches and volumes. Card edge contact cleaning. Solder correction. Bias and offset checks. Output audio check)
Accessories: No accessories
Main specifications: 250W+250W (stereo 1/2/4/8Ω) 500W (mono 0.5/1/2/4/8/16Ω) input sensitivity (0.75V/2.5V) switchable W411 x H181 x D368 mm 37.2kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/15 sales price 118,000 yen Maintained! The thin preamp from the musical Fidelity has an English style taste where you can feel the elegance, and the perfect balance of high frequencies that don't insist too much on the thick, thick mid-low range unique to this era feels good. The tape/monitor switch has been repaired and replaced and is a non-genuine product. The exterior is dull overall, with small scratches and a lot of feeling of use (Asaine Tomoho)
Maintenance information: 2023.10.26 maintained (TAPE1 monitor switch defective → non-genuine silver knob replacement. Rear terminal screw idle rotation all replacement, operation check) 2023.10.12 maintained (main VOL noise → replacement. Treble distortion noise VOL replacement (original not available, replacement with replacement, no click on the midpoint position) IC, DC leak defect replacement, capacitor deterioration replacement, operation check.
(We will not be able to respond if the dedicated parts are defective in the future)
Accessories: none
Main specifications: external power supply system with PHNON (MM MC) CR type RIAA equalizer output 2 systems W482 x H57 x D166 cm 3.0 kg
Y lug plug set of 4 have mirror-polished terminal contact parts made of leadless brass material with excellent conductivity, and rhodium plating treatment has been applied to the surface to further improve conductivity and durability (Tamura Eiji)
Accessories: original box, instruction manual
The price has been drastically reduced! 2024/4/18 sales price 178,000 yen 2024/1 maintenance completed! It is a Harves speaker with increased appeal, such as the richness of the sound typical of an HL MONITOR. The Harves-like sound, which is characterized by a relaxed sound in addition to the mid-range density unique to those made in England, is attractive. Exterior maintenance has been carried out on the exterior, but in addition to scattering repair marks, there is a feeling of use over time, such as undulations on the woofer edge. *Saran net is not included. Serial 3349A 3349B (Tomonori Asaine)
Maintenance information: 2024.1.12 Maintained (exterior repair stain tinted front baffle repair polishing paint rear baffle cleaning
Woofer edge repair, protective agent application (with undulations), terminal replacement unit, detachable tweeter, corrosion, disconnection repair, diaphragm, dome coat treatment, 1 voice coil, bobbin deformation correction)
Accessories: none
Main specifications: 2 way 2 speakers, 22.5 cm cone woofer/2.5 cm soft dome tweeter impedance 8 Ω crossover 2,000 Hz sound pressure level 87 dB, W325 x H640 x D330 mm, 13.5 kg
The price has been reduced! 2024/4/21 sales price 12,000 yen DENON tonearm DA-401 exclusive headshell. They rarely appear separately, so if you are looking for one, please take this opportunity (Tomoho Asaine)
Maintenance information: 2024.4.21 continuity confirmed
Accessories: none
Main specifications: dead weight 4 g
The price has been drastically reduced. 2023/12/11 sales price 15,000 yen*There is no problem with operation, but since it is cheap, it is being delivered as is. Center speaker for the company's STAGE series. Please help build a theater system (Daiki Goto)
Maintenance information: 2023.12.11 operation confirmed
Accessories: instruction manual
Main specifications: 2-way dual 133mm woofer, 25mm aluminum treble unit impedance 6Ω efficiency 88dB W469 x H190 x D220 mm weight 7.95 kg
*Due to poor LOW volume, the specification has been changed so that only the low frequencies come out at full throttle. Other volumes can be used as normal. A pretty rare Yamaha channel divider. An electronic crossover network equipped with continuously variable crossover frequency, a 3-stage slope selector, and a Q control circuit. For 2 to 3 ways. The exterior has small scratches and dullness (Oikawa Tetsuji)
Maintenance information: 2024.4.24 Maintained (switches and volume contact repairs, LOW volume has passed circuitwise because parts cannot be obtained)
Accessories: none
Main specifications: crossover frequency Low-Mid: 50 Hz, 100 Hz, 200 Hz, 400 Hz, 800 Hz Mid-High: 800 Hz, 1.6 kHz, 3.2 kHz, 6.4 kHz, 12.8 kHz Low-Mid: 35 Hz to 1.13 kHz continuously adjustable by crossover fine adjustment knob, Mid-High: 565 Hz to 18.1 kHz continuously variable W435 × H72 × D349 mm 7.5 kg
Maintained! The successor to the PM-80. MOS-FET is used to create a unique world view with gloss in the mid-range. The plump, thick sound during Class A operation is unrivaled, and you can relax and immerse yourself in the music. On the exterior, there is a feeling of use such as seal marks, dullness, and small scratches on the top plate. Serial MZ009432260139 (Yasuhito Koshihama)
Maintenance information: 2024.2.17 Maintained (all main amplifier board soldering deterioration fixed. Bad output relay contact replacement. Disassemble and sharpen the input switch and apply contact cleaner. (Long time sound check)
Accessories: none
Main specifications: MOS-FET use, AB class switchable, Class A (20W+20W), Class AB (100W+100W) PHONO input (MC/MM switching), W454 x H165 x D380 mm 17.5 kg
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
Digital cable 1.5m DENON LINK cable This is a dedicated cable that maximizes the performance of the high-purity copper high definition digital audio interface DENON LINK. Stable high quality digital transmission without being affected by the surrounding environment has been achieved by thoroughly eliminating vibrations from the plug and shield (Tamura Eiji)
Accessories: original box, instruction manual
LAN cable 1.0m AIM audio LAN cable The amount of information is suitable for a high-end machine, and the high resolution and good freshness are attractive (Yonejima Satoshi)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
The 1.8 m PSE standard MK2 power cable is not only flexible and easy to use, but the sound quality has also been brushed up with fewer habits. You can get clear, sharp sound. There is a frayed sheath (Tamura Eiji)
Maintenance information: 2024.4.24 continuity confirmed
Accessories: none
The 1.8 m PSE standard MK2 power cable is not only flexible and easy to use, but the sound quality has also been brushed up with fewer habits. You can get clear, sharp sound. There is a frayed sheath (Tamura Eiji)
Maintenance information: 2024.4.24 continuity confirmed
Accessories: none
Maintained! DENON's vintage pre-main. It has a sense of transparency, three-dimensionality, and sound field that you wouldn't think of an amp from the 70s. Also, be sure to try out the deep and tasteful tuning that you can never enjoy with the company's current models. The cost performance is high! You can see a feeling of use such as appearance, dullness, stains, scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.24 maintenance completed (switch disassembly contact polishing, contact cleaner application) 2013.2.19 maintained (54 deteriorated transistors and capacitors replaced/use of nichikon MUSE, etc., RCA terminal replacement, speaker terminal replacement, input/output waveform confirmation, sound output test OK)
Accessories: copy of instruction manual
Main specifications: pre, main separable 32W+32W (8Ω) PHONO2 system (mm) W370 x H141 x D310 mm 8 kg
Vacuum tube CD players are rarely in stock. It looks like a product manufactured in Germany and the Netherlands based on the MarantzCD-4000 package, and you can comfortably listen to the mild sound quality unique to tube balls and the gorgeous high frequencies that pop out. This is a great item for those who want an accent to the sound. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.19 Operation confirmed
Accessories: instruction manual
Main specifications: W440 x H90 x D270 mm weight 3.82 kg
Pair tube military high reliability tube 6V6GT equivalent tube black base smoke measurement value 84/84 (rejected value 46), all but the printing on the top of the tube with white box has disappeared, but it was determined that it was CV511 based on the structure ※The pair was determined based on the gM value measured by the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Pair tube military high reliability tube 6V6GT equivalent tube tea base smoke code: 7220/7220 measured value 92/92 (rejected value 46) with original box*Pairs are judged based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: original box
Pair tube military high reliability tube 6V6GT equivalent tube tea base smoke code: 7220/7220 measured value 90/88 (rejected value 46) with original box*Pairs are judged based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: original box
The disposal price has been reduced! (Member prices are not applicable) 2024/4/14 sales price 198,000 yen This model takes the configuration of the flagship 7S1. The quality of the sound has improved compared to the predecessor, and in particular, the thickness of the sound has increased from low to medium, making it a well-balanced sound. The clear and clean spatial expression and smooth, gentle mid-high sound are attractive. There is a scratch on the top plate. Serial 20011208001208 (Fujisawa Yukishi)
Maintenance information: 2024.4.14 Operation confirmed
Accessories: remote control, instruction manual, power cord, connection cord
Main specifications: original mechanical module SACDM-1 1 bit DSD SEIKO NPC SM5866AS D/A converter with external clock terminal W440 x H127 x D413 mm 16.5 kg
The price has been drastically reduced. 2024/4/19 sales price 698,000 yen Maintained in 2023! Hammer tone BBC specification! Strobe platter included! This is a combination of GARRARD 301 and SME 3009S2, which has an attractive gripping, and gutsy sound. The high sensitivity short arm with high utility and the sound produced from the idler turntable is exhilarating and very comfortable. It is a record player system that allows you to experience the true essence of analog. Since the shaft on the back of the motor is long, an Audio-Technica insulator is included. *Currently, the pulley is 60 Hz, but the strobe platter is for 50 Hz (Murakoshi Yoichi)
Maintenance information: 2023.8.15 maintenance (motor disassembly/check, lubrication, assembly. Main bearing disassembly, cleaning, oil injection, oil sealant application, assembly. Overall cleaning. idler cleaning. Motor suspension spring rubber replacement. Transport plate fixing clip. Linguage distortion correction. Noise suppressor rebuild replacement. Mount rubber washer added. 50Hz pulley adjustment added. SME3009S2 cleaning. Mount grommet replacement Contact cleaning. (Running test)
Accessories: insulator (audio technica AT616)
Main specifications: 301: idler drive 33, 45, 78 rotations compatible 3009S2: short arm static balance type, total length 265 mm, overhang 15 mm, needle pressure (when 1 rider weight is attached) 1 memory 0.25 g step 0 g to maximum 2.5 g (when 2 rider weights are attached) 1 memory 0.5 step 0 g to maximum 5 g cartridge dead weight up to 28 g size W480 x D406 x H238 mm weight 12.5 kg
Pair tube direct heat triode tube, white base, made in Slovakia, measured value 76/70 (rejected value 58) with original box*Pairs are determined based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: original box
※Inexpensive because it is in poor condition. Self-made 2way/3way enclosure. The size of the hole is different at the top, with an opening diameter of about 315 mm on the top and about 360 mm on the bottom. There are many peeling veneer, corner pads, scratches, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: W450 x H1056 x D480 mm approx. 33 kg
※1 bottle only. Maintained! The classic model for professional 1" screwdrivers. It is a driver that is installed in many of the company's 43 series, etc., and is easy to balance with various woofers and tweeters (Daiki Goto)
Maintenance information: 2024.4.23 Maintained (diaphragm installation adjustment, replacement of the following parts. DCR (54871, 5.7 ohm diaphragm, no scratches)
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms (measured 10/12 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Fully maintained, including woofer edge replacement and exterior repairs! A rare model is in stock. British Spendall SP100 derived from the German national broadcast monitor. It goes great with classical music, from symphonies to chamber music, as well as European jazz. The elegant expression unique to European models is fascinating. Serial 3918, 3919 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 maintained (exterior repair/polishing/clear finish, saran net replacement, woofer edge replacement, mid edge replacement, all internal faston terminals replaced)
Accessories: saran net, jumper plate
Main specifications: 3-way bass reflex type 8Ω frequency characteristics 45 to 20 kHz 100W W370 x H700 x D430 mm 36 kg
Maintained by the manufacturer! The third generation of the Denon 2000 series. Frequency characteristics have been improved and low noise has been achieved by reviewing power parts, volume circuits, etc., while keeping the low frequency range with a sense of volume unique to the company and the high frequency range with elongation unchanged. Of course, it is a big hit model that is compatible with modern sauces, and doesn't make you feel that it's poor to listen to old sources. There is dullness and a feeling of use. Serial 1050502942 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 manufacturer maintained (main volume and selector switch disassembly contact cleaning. (Idle current adjustment and operation inspection carried out.)
Accessories: power cord
Main specifications: output 80W+80W (8Ω) PHONO (MM/MC) bi-wiring compatible dimensions W434 x H180 x D478 mm weight 22 kg
*Set of 3. A gradation cast iron insulator that firmly supports equipment with heavy construction. The excellent damping properties of cast iron and the vibration blocking effect of pinpoint support make the mid to low range blurring clear, and accurate sound images can be obtained. There is a feeling of use such as dullness and small scratches (Hiroki Aso)
Accessories: original box spike base
Main specifications: Gradation cast iron, matte black finish, diameter 60 x height 45 mm, weight 800 g/piece, plate diameter 35 x height 5 mm
with logo! This headshell is popular due to its combination with the Technics and SL-1200 series. It is made of aluminum die-cast with high rigidity, and brings out the characteristics of the cartridge (Hiroki Aso)
Maintenance information: 2024.4.17 continuity confirmed
Accessories: none
Main specifications: Die-cast aluminum, dead weight 10.2 g