Maintained! New Recutural York with HPD385 in the original box. All refreshed after network capacitor replacement, unit overhaul, and enclosure maintenance! The sound of the box is very rich. The piano overtones are pleasant! The golden cheek finish, which is typical of Tannoy's vintage, is reminiscent of an English sound. The balance between the 15-inch unit and enclosure volume is excellent, and there is no dubbing, yet it draws in a way that is scaled. The exterior has been beautifully finished due to maintenance
(ASAINE Tomonori)
Maintenance information: 2024.5.16 Maintained (exterior repair/polishing/clear finish, saran net cleaning/repasting, ATT frame plate painting
Unit maintenance (low frequency edge replacement, magnetic circuit rust removal/horn coating/gap cleaning/center adjustment, fastener polishing, high frequency side magnetic circuit rust removal/gap cleaning/center adjustment) Unit detachment network maintenance: frequency characteristic check, ATT cleaning, terminal/4 pin terminal cleaning)
Accessories: none
Main specifications: used unit HPD385 frequency characteristics 20Hz to 20kHz allowable input 85W 92dB 8Ω W600 x H1075 x D380 mm approx. 42 kg/bottle
Maintained! A speaker that allows you to enjoy the powerful sound of JBL. A vertical twin that uses bi-radial horns for the tweeter and is developed with upper and lower 20cm woofers. Sound pressure, which is characteristic of horns, is uniformly distributed within the area, and you can experience a wide service area. The exterior has been beautifully finished due to maintenance. Serial 5340-015070 5340-015071 (Asaine Tomoho)
Maintenance information: 2024.5.16 Maintained (exterior cleaning/touch-up saran net cleaning/frame repair/paint tweeter maintenance (magnetic fluid removal/cleaning/center adjustment in the magnetic circuit gap, left and right sound pressure difference adjustment, internal urethane replacement) woofer maintenance (edge replacement, gasket preparation and installation) unit detachment)
Accessories: saran net
Main specifications: output sound pressure level 92 dB frequency characteristics 35 Hz to 20 kHz W318 x H965 x D413 mm weight 34 kg
Maintained in September 2020! The highest-grade cassette deck equipped with dbx. The power supply unit and amplifier section have been thoroughly strengthened, and the sound quality as a cassette deck has been further enhanced. The impression is that the sound is clean without exaggerating too much. The exterior is dull and has a feeling of use. Serial 20415-07903 (Tomonori Asaine)
Maintenance information: 2020.9.28 maintenance implementation (capstan belt replacement and tape speed check, head base drive belt replacement, pinch roller detachment inspection cleaning and tape running check, operation key tact switch replacement x11, tape selector switch contact cleaning procedure, pattern correction and replacement due to C48/47 electrolytic capacitor installation problems, power cord replacement, and playback level adjustments are high (Since it is folded, it is readjusted to a normal value and the recording level is adjusted, the recording test using the music source is good, Dolby recording, and the DBX recording and playback operation is good)
*Reference value: W&F (WTD) for self-recording and playback: 0.05% is good, but depends on the tape used.
*You may hear a slight squeaking sound from near the panel of this unit. Please note that this is a driving sound caused by pulses for lighting generated from the display tube (FL tube), but it cannot be removed.
Accessories: none
Main specifications: 3 head frequency characteristics 20Hz to 21kHz W475 x H112 x D353 mm 7.3 kg
Both inside and outside have been maintained! This is an ultra-rare speaker Allegro equipped with Monitor Gold. This bookshelf is almost the same size as a 3LZ. It is an attractive speaker with a beautiful sound unique to Monitor Gold and a mid-low range resolution that is a bit different from 3LZ. It lets me listen to quality that is compatible with everything. Serial SG1515/SG1517 (Yonejima Satoshi)
Maintenance information: 2024.5.12 maintained (saran net reinstallation/resonance prevention measures, unit maintenance: magnetic circuit gap cleaning/center adjustment for both low and high frequencies, network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning, 4-pin direct connection modification repair. Exterior repair/polishing/oil finishing, rear baffle repair/painting)
Accessories: No accessories
Main specifications: unit using a coaxial 2-way bass reflex speaker system 12 inch MONITOR GOLD coaxial 2-way playback frequency band 25 Hz to 20 kHz maximum input 15 W input impedance 8 Ω crossover frequency 1 kHz dimensions W380 x H583 x D 240 mm weight 16.2 kg (actual measurement)
The price has been reduced! 2024/5/15 sales price 128,000 yen LINN network audio player with integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1220444 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed.
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
The price has been reduced! 2024/5/15 sales price 128,000 yen LINN network audio player with integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1234701 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
In January 2023, both the interior and exterior were maintained and brushed up! ORIGINAL LANSALOY EDGE! The OLYMPUS S8R representing JBL has arrived. The 075 tweeter is full of realism, with the sound of a driver blowing fire into the thick, dry low frequencies, and a sense of realism that leaves graininess. You can enjoy the real thrill of vintage audio. Outside of the exterior, the back plate on one side is missing, and the finish is beautiful due to maintenance (Kobayashi Hitoshi)
Maintenance information: 2023.1.10 maintenance (exterior repair, polishing, baffle/hakama repair before and after oil finishing, painting, lattice repair, polishing, painting, lining replacement. Woofer maintenance (edge softening treatment, corn paper coating, passive corn paper coating). Driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound-absorbing material replacement, terminal contact cleaning). Tweeter maintenance (horn disassembly/polishing, magnetic circuit rust removal/gap cleaning, terminal contact cleaning). Network maintenance (LX5: terminal rust removal, acid washing, insulation bush & mounting screw replacement. ATT (SW type) disassembly contact polishing and cleaning. Reinforced with silicone to prevent the coil from coming off A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. N7000 terminal rust removal, acid cleaning, insulation bush, and mounting screw replacement. ATT replacement with a brand new one. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check input/output waveform and balance, check sound output))
Accessories: saran net, diffuser, instruction manual
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1020 x H670 x D510 mm weight 82 kg
All internal deteriorated capacitors and parts have been replaced! Furthermore, a new dust cover has also been created so you can use it comfortably. A masterpiece model of a semi-auto player. The torque and braking power of the motor are excellent, and the stability of operation is impressive. The sound quality, which is delicate and has an excellent sense of resolution, brings out the performance of the cartridge well. There are thin threads on the exterior. Serial 10700499 (Yonejima Satoshi)
Maintenance information: 2024.2.29 Maintained (new dust cover created, motor part removed, shaft and bearing cleaned and lubricated. The tact SW on the operation part and the electrolytic capacitor on the internal board were replaced with a new one. Resolder the board. Remove the area around the arm, clean each part after disassembly, replace the shaft bearing, inspect the internal lead wire, and reassemble. Dust cover hinge reinforcement bracket created. Exterior cleaning, cabinet scratch polishing, rotation speed check, operation test of each part, sound test)
Accessories: instruction manual, screws, EP adapter
Main Specifications: Quartz Lock DD Drive Auto Lift Up Static Balance Type Compatible Cartridge Weight 2 to 12 g Needle Pressure Range 0 to 3 g W490 x H182 x D410 mm 14.5 kg
It's early plastic shell, but the interior has been replaced with a new one. The rich, rich SPU-like sound is attractive. The built-in transformer gives the impression that transparency and clarity have been improved. The exterior is broken into the plastic cover, and there is a feeling of use such as dullness. Serial 624056 (Murakoshi Yoichi)
Maintenance information: 2024.5.8 sound output confirmed
Accessories: original box
Main specifications: MC type with built-in transformer, output 10 mV, needle pressure 3 to 4.5 g, dead weight 32 g
M/MC compatible A tubular phono equalizer developed with the aim of better analog reproduction. You can enjoy a warm, natural sound using a vacuum tube non-feedback amplifier and a CR-type equalizer. The impedance can be switched according to the cartridge. Externally, there are line scratches on the top plate. Serial 00180 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: power cable
Main specifications: MM/MC compatible 12AX7 (ECC83) x 2 W300 x H100 x D260 mm 4.8 kg
Both the interior and exterior have been maintained and brushed up! The OLYMPUS S8R representing JBL has arrived. The combination of thick, dry low frequencies, the sound of a driver that seems to blow fire, and the 075, which leaves a gritty feeling of realism, is impressive. Please enjoy the real thrill of vintage audio. The exterior is also beautifully finished (Yonejima Satoshi)
Maintenance information: 2024.5.11 Maintained (network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/screw replacement, exterior cleaning. Woofer maintenance: edge replacement, cone paper coating, passive cone paper coating. Exterior repair/polishing/oil finish, front and rear baffle/hakama repair/painting. Lattice repair/polishing/painting, lining replacement. (Detaching the unit, repairing the diffuser)
Accessories: saran net
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1,020 x H670 x D510 mm weight 82 kg
※1 bottle only. By adopting a diaphragm with a weight of 0.03 g or less and a magnetic circuit with a strong magnet that makes use of the characteristics of the 1000m tweeter berylum material, we have achieved smooth frequency characteristics and excellent start-up even at the high end. The sharp, realistic sound quality is a fresh and transparent sound. The exterior has a feeling of use such as dullness and scratches (Jun Tamai)
Maintenance information: 2024.5.10 sound output confirmed
Accessories: none
Main specifications: size W115 x H45 x D115 mm 0.9 kg (actual measurement)
The price has been reduced. 2024/4/10 sales price 26,800 yen ※6 month warranty triode MM/MC compatible phono equalizer. You can easily enjoy records even with an amplifier that does not have a PHONO input. It's slightly dull (Daiki Goto)
Maintenance information: 2024.4.10 operation confirmed
Accessories: instruction manual, power cable
Main specifications: semiconductor circuit input impedance mm47kΩ/mc2Ω to 47Ω compatible gain mm36dB/mc55dB W90 x H100 x D230 mm 1.6 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/2/10 sales price 198,000 yen Maintained! According to the 117V specification of the tubular mono FM tuner, reception is unstable at 100V. The Japanese band has been changed, and reception sensitivity is good. It is a tuner that strongly shows the characteristics of Mackin's sound, which is thick, soft, and glossy. There is corrosion and rust throughout the exterior. Serial 292099 (Tomoho Asaine)
Maintenance information: 2024.2.10 Maintained (meter readjustment with coil and right side volume, left side lamp off replacement, IF/RF/MPX readjusted)
2018.2.22 Maintained (VT12AT7 replacement/MPX section transistor replacement/RF/IF/MPX re-adjustment)
2016.1.25 Maintained (6 additional VT shortages. 2 VT replacements 4 additional ceramic C for BAND EX Ceramic C replacement. Chemical C exchange. Front lamp repair, block.C50uf x 4 replacement Step up transformer 100V ⇒ 117V added)
Accessories: 117V step up transformer
Main specifications: FM dedicated tuner W400 x H130 x D300 mm 8.6 kg
The price has been drastically reduced. 2024/5/10 sales price 468,000 yen Maintained! By installing a double 10-inch (25cm) diameter woofer while equipped with a traditional JBL horn and compression driver, a slim tall boy style is achieved with sufficient low frequency energy. It is an excellent speaker that combines low frequencies with instantaneous power typical of JBL and sharp mid-high frequencies. The exterior is good with no noticeable scratches (Shota Sasaki)
Maintenance information: 2024.5.10 Maintained (magnetic fluid removal/cleaning/center adjustment in the single-sided driver magnetic circuit gap)
Accessories: none
Main specifications: 3-way 4-speaker woofer 100FE-12 scoker 175Nd-3 tweeter 139 Nd playback frequency band 33 Hz to 40 kHz crossover frequency 850 Hz/12 kHz impedance 6 Ω output sound pressure level 92 dB allowable input 250W (RMS) W370 x H1,007 x D368 mm 39 kg
The price has been reduced. 2024/5/10 sales price 42,800 yen This 2-way bookshelf with monitor audio will be introduced for the first time at Hi-Fi. The C-CAM unit introduced in the Bronze Series pursues sound quality. The high cost performance and sound typical of the company are attractive (Murakoshi Yoichi)
Maintenance information: 2024.5.10 sound output confirmed
Accessories: instruction manual, saran net, bass reflex sponge, jumper, rubber feet, original box
Key Specifications: 2 Way 8Ω 85dB Crossover 2,500Hz W166 × H281 × D268 mm 5.0 kg
The sound of the shell, which determines the rich sound of the SPU called the “core of the MC cartridge,” is enhanced by blending wood powder and resin. It is a modern SPU that combines the softness and intensity of the classic series sound. It's very slightly leaning to the left. Serial 730862 (Oikawa Tetsuji)
Maintenance information: 2024.5.12 operation confirmed
Accessories: original box, needle cover
Main specifications: MC type output voltage 0.2 mV impedance 2 ohms frequency characteristics 20 to 25,000 Hz internal resistance 6 ohms diamond needle nude elliptical (elliptical needle) suitable needle pressure 4 g dead weight 32 g
Mono exclusive MC cartridge. It's not flashy, but it stretches and makes a gentle sound that is pleasant. There is a feeling of use such as dullness (Daiki Goto)
Maintenance information: 2024.5.13 operation confirmed
Accessories: original box, instruction manual
Main specifications: MC type 0.5 mV needle pressure 2.5 to 4.5 g dead weight 5 g
A horn type tweeter that is an improved model of the JA-0506. Alnico magnets are used for the magnetic circuit, and hollow-out aluminum is used for the horn part. A hard duralumin V-shaped ring diaphragm is used for the diaphragm. The sound is bright and clear (Daiki Goto)
Maintenance information: 2024.5.13 (operation confirmed)
Accessories: original box
Main specifications: horn type tweeter unit Alnico magnet 0.23 kg impedance 8 ohms playback frequency band 3 kHz to 20 kHz recommended usage band 5 kHz or more rated input 1 W maximum input 2 W sound pressure level 109 dB
The disposal price has been reduced (member prices are not applicable). 2024/2/16 sales price 378,000 yen ※The power supply part has been newly created. Other internally deteriorated parts have been restored! 2-way 100Hz specification An electric crossover coveted by Mark Levinson fans. You can see how well the early Levinson was built can be seen from the feel of the knobs that seem to make you addicted. You can listen closely to Levinson's unique sounds even on Divider. The exterior has scratches on the front top plate and other threads (Mizusaki Ryo)
Maintenance information: 2024.2.16 Maintained (*Since there is no power source, new power supply and connection cable were manufactured, noise appears in the LChLow output, transistor defects in the low pass module were replaced, re-encapsulated, readjusted due to left and right level differences, 4 volume contacts were cleaned, specs were inspected, and blocking characteristics were inspected. The crossover is 100Hz)
Accessories: Power supply unit (newly created, non-genuine), power cable, copy of instruction manual
Main specifications: 2 way (100 Hz specification) closed module type RCA Remo input/output size (main unit) W483 x H51 x D156 mm 2.8 kg size (power supply part) W101 x H101 x D256 mm 2.2 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/7 sales price 398,000 yen Exterior maintenance completed! Replace network capacitors with SOLEN film capacitors. The unit is DENTECH Tune HDP385, and the enclosure is made by Shinkosha. The unit is attached by removing the back plate, and the net does not come off the front. Classical music also goes well with symphonies. The exterior is generally beautifully finished due to maintenance. Serial AYT71012 AYT71012 (Tomonori Asaine)
Maintenance information: 2024.3.7 Maintained (exterior repair/cleaning
Rear baffle paint saran net replacement unit maintenance (exterior cleaning, low range center adjustment, screw tightening, high frequency magnetic circuit slit cleaning/center adjustment) ATT cleaning/knob adjustment unit detachment)
2015.5.14 Maintained (network capacitors replaced with SOLEN. Unit edge replacement. Magnetic circuit overhaul and operation adjustment. Saran net partial cleaning net tear repair, complementary color correction)
Accessories: none
Main specifications: used unit HPD385 frequency characteristics 20Hz to 20kHz allowable input 85W 92dB 8Ω W600 x H1075 x D380 mm approx. 42 kg/bottle
The A3500 vacuum tube power amplifier has been refreshed by thorough maintenance down to the smallest details, such as volume disassembly and polishing. The warm, fresh tone, filled with the appeal of a vacuum tube type, is still appealing enough today. You can enjoy music with a rich, thick tone that contrasts with the clicking tones of recent vacuum tube amplifiers. As for the exterior, paint deterioration and peeling can be seen on the transformer on one side, and there is a feeling of use such as dullness, small scratches, etc., and there is a dent in the hood. ※3-pole tube connection specification. 20W+20W (actual measurement) is output as specified by the manufacturer (Takasaki Atsushi)
Maintenance information: 2023.2.3 maintained (main tube (6CA7) replacement vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, complete disassembly of semi-fixed VR replacement power input gain volume, contact polishing, anti-oxidation/sulfation grease coating load test (8Ω load 1kHz 20W+20W) input/output waveform confirmation sound output check performed)
Accessories: copy of the manual
Main specifications: 20W+20W (8Ω) vacuum tube 6CA7×4/6AQ8×3 W465×H168×D206mm 16kg
RCA cable, 1.0 m pair, 6N ultra-pure copper and 70 specially twisted hybrid structured conductors with OFC copper, an R resonator is attached as a damping function based on a new concept, and the plug is an original collect chuck. It's a natural, highly transparent sound quality with few habits typical of SAEC. There are scratches around the plug (Kojima Yosuke)
Accessories: none
Phono cable, 1.3 m, 5P-RCA specification, PCOCC conductor, the standard model of an easy phono cable, since it is a PCOCC conductor, the resolution is excellent. There is friction and dirt on the sheath (Kojima Yosuke)
Accessories: none
Balance cable, 0.7 m pair, PC-Triple C conductor, conductor with stable electrical characteristics such as ultra-low distortion ratio and high conductivity, and double shielding for perfect noise countermeasures. It has an edgy, well-cut sound using a gold plated plug made by Neutrik. The lettering is frayed and thinned. (FUJISAWA KOSHI)
Maintenance information: 2024.5.12 continuity confirmed
Accessories: No accessories
Maintained! It comes with a rare hood! A single stereo power amplifier using a 2A3 output tube that made the Sun Audio name popular. You can enjoy the aftertaste of sound and air unique to vacuum tubes. It expresses vocals and string music in a sweet and glamorous manner. It is an affordable and well-built car (Murakoshi Yoichi)
Maintenance information: 2024.5.12 maintenance completed (first stage vacuum tube replacement on the left channel, volume washer, spring replacement, electrolytic capacitor deformation replacement, missing screw installation, excessive abrasive removal, vacuum tube pin cleaning, solder correction, bias check, ham balance adjustment, output check approx. 4W confirmation (currently 8Ω load setting))
Accessories: power cable
Main specifications: rated output 3.5W+3.5W vacuum tube 2A3 x 2 6H8C x 2 5U4G x 1 W360 x D210 x H190 mm 16 kg
The latest cable technology has been introduced, such as a domestic high-purity PVC conductor (premium virgin oxygen-free copper) insulator, air-containing PE material (30% air content), and a 2-core twist structure for the 0.6 m pair conductor of the RCA cable. It has a clear and sharp AET sound (Jun Tamai)
Maintenance information: 2024.5.12 continuity confirmed
Accessories: original box
Maintained. It is a model equipped with the SME 3009R on the LINN LP12. Compatible with everything from lightweight types to heavyweight cartridges such as SPU. Please enjoy the good balance of the large number of sounds unique to analog, the separation of tones, and the profound thickness. There are scratches and dullness on the exterior (Tamura Eiji)
Maintenance information: 2024.5.8 Maintained (power circuit electrolytic capacitor replacement. Arm operation and voice check. (*33 rotations only)
Accessories: No accessories
Main specifications: 3009r/static balance type short type needle pressure 0 to 5g compatible cartridge weight 9.5 to 22 g LP12/W445 x H140 x D356 mm 10.5 kg
Maintained in 2023. After all, the warm, and glossy sound quality is excellent for stringed instruments. It has a soft and vivid sound not found in transistors, making it perfect for listening for long periods of time. In addition to noticeable scuffs and paint peeling on the exterior and transformer area, dullness and a feeling of use can be seen. Serial F0800283 (Murakoshi Yoichi)
Maintenance information: 2023.7.23 maintained (vacuum tube socket block capacitor electrolytic capacitor oil capacitor SP and RCA terminal semi-fixed VR fuse holder replacement load test (8Ω load 1kHz 25W+25W) input/output waveform confirmation sound output check performed gain VOL NFB switching SW disassembly contact refinement to prevent oxidation and sulfation grease coating input/output waveform confirmation distortion load test (1 kHz (25W+25W at sine wave 8Ω load) sound output test)
Accessories: copy of instruction manual
Main specifications: 50CA10 push-pull output 30W+30W W410 x H183 x H160 mm 13.8 kg
Internally and externally maintained! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. There is a very slight dent in the tweeter grill, and there are repair marks on the side (Murakoshi Yoichi)
Maintenance information: 2024.3.4 maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network frequency characteristic check, ATT cleaning, terminal replacement)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
Both the interior and exterior have been fully restored and refreshed! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. It is beautiful due to exterior repairs (Sasaki Shota)
Maintenance information: 2024.5.10 Maintained (exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting. Saran net replacement/frame repair/reinforcement. Unit maintenance: low range/edge exchange, magnetic circuit gap cleaning/center adjustment, high pass/magnetic circuit rust removal/gap cleaning/center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, faston terminal replacement, terminal cleaning)
Accessories: none
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Full maintenance, such as internal and external maintenance, was carried out, and the finish was beautiful! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. Serial 55553L, 55553R (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (exterior repair/repaint) 2017.4.25 Maintained (exterior polishing/all coated woofer cone paper/unit frame paint chip putty repair grill dent correction/paint tweeter distortion and maintenance (edge deformation repair, magnetic circuit slit maintenance complete) unit detachment terminal replacement (banana plug compatible product) ATT cleaning capacitor replacement*Some capacitors before replacement Since it is difficult to remove, remove the wiring to check the remaining input/output waveform and balance, sound output check, frequency characteristic measurement check (~ 42 kHz)
Accessories: No accessories
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
DENON's classic MC cartridge. The balance of localization and sound is excellent, and all music genres can be played without difficulty. I can recommend this cartridge to a variety of people, from analog beginners to experts (Murakoshi Yoichi)
Maintenance information: 2024.5.8 sound output confirmed
Accessories: needle cover, case
Main specifications: MC type output voltage 0.3 mV playback frequency 20 Hz to 45 kHz electrical impedance 40 ohms needle tip 16.5 microns round needle pressure 2.2 to 2.8 g dead weight 8.5 g
The disposal price has been reduced. Member prices are not applicable. 2024/3/21 sales price 128,000 yen Maintained! Quad power amplifier Despite its compact body, you can enjoy a smooth, thick sound. It really goes well with speakers made in England, and makes you listen to 70s analog sound with a sense of dynamism. The exterior has a feeling of use appropriate for the model year, such as line scratches on the top plate, rubber footprints, and overall dullness (Mizusaki Ryo)
Maintenance information: 2024.3.21 maintained (internal Tn, C, R check, Tn OK, gain setting C, DC cut C, etc. → replacement, DINININPUT connector replacement, cable creation ~ operation check)
Accessories: power cord, connection cord, copy of instruction manual
Main specifications: 100W+100W frequency characteristics 20 to 20 kHz dimensions W341 x H115 x D195 mm weight 9 kg
The disposal price has been reduced! Member prices are not applicable. 2024/4/6 sales price 218,000 yen ※The exterior is in poor condition, so it's cheap. Maintained! 100V specification genuine Baes product. A control amplifier representing the golden age of Macintosh. Compared to the C28, this model has a wider range and more subtlety. The rich, glossy, and thick tone is alive and well, especially with vintage speakers. The exterior has rust spots, paint deterioration, and unevenness on the front. Serial JBZ7419 (Fujisawa Yukishi)
Maintenance information: 2024.4.6 maintained (TONE, MODE, INPUT, BAL etc. disassembly contact polishing grease applied. All push switch contacts are coated with abrasive grease. Mode switch, volume, balance volume contact cleaning. Electrolytic capacitor replacement. Panel lamp replacement Panel peeling correction. ※Since the panel color is burnt, there is color unevenness with the correction part. (Check the operation of each input/output)
Accessories: No accessories
Main specifications: frequency characteristics 20 Hz to 20 kHz input terminals PHONO 1 · 2, AUX, TUNER, TAPE 1 · 2 W406 × H138 × D330 mm 8.6 kg
The price has been drastically reduced. 2024/4/25 sales price 448,000 yen Maintenance is being carried out in 2020. It's a famous machine you can't miss when talking about Marantz sounds of yesteryear. It has a good mid-range fat transfer, and its pleasant sound is an appeal that cannot be obtained anywhere else. You can enjoy the Marantz sounds of the good times. There is some rust and small scratches on the exterior. Serial 8-4160 (Murakoshi Yoichi)
Maintenance information: 2020.11.18 maintained (AC code deterioration replacement, 40/40/20 μF and other deterioration replacement, 3 external paint, 20 μF x 2 deterioration replacement, selenium deterioration countermeasures → diode addition · vacuum tube 6BH6 noise exchange · vacuum tube socket and RCA jack caulking repair ※ other operation checked (measured at 32 to 41 W SP: 8 Ω with rated output AC 100 to 117 V) *A2 The EL34 vacuum tube guide pin is broken, but there is no problem with performance. (Part of the SP terminal on the right channel is missing.)
Accessories: instruction manual (for replicas, Japanese copy)
Main specifications: 35W+35W vacuum tube 6CG7/6BH6/EL34 W348 × H191 × D273mm 22.5 kg
The disposal price has been reduced! (Member price not applicable) 2024/4/28 sales price 178,000 yen A power amplifier with a sense of speed and sharpness unique to Threshold. The sense of volume in the mid to low range is also sufficient, and it makes you enjoy music with dense sound throughout the entire range. There are small scratches and dullness on the exterior. H8010186 (Fujisawa Yukishi)
Maintenance information: Maintained on 2013.10.6 (electrolytic capacitor volume replacement, circuit protector replacement. Replace the rubber foot and replace the input RCA jack. Bias and offset checks, maximum output checks, interior and exterior cleaning)
Accessories: power cord
Main specifications: 100W+100W (8Ω) W480 × H192 × D342 mm 24 kg
MC cartridge using LC-OFC (linear crystal/oxygen-free copper) wire based on DL-103. Familiar sound with a wide range. The supple sound makes it comfortable to listen to. The exterior has a feeling of use, such as dullness on the body. Serial 4126 (Hiroki Aso)
Maintenance information: 2024.4.21 sound output confirmed
Accessories: none
Main specifications: MC type output 0.25 mV, proper needle pressure 2.2 to 2.8 g, internal impedance 13 ohms, own weight 8.5 g
Maintained! A popular DENON control amplifier for its excellent phono equalizer. MC head amplifiers are famous for their quality, and they fully draw out the amount of information in the cartridge. It's a neat sound typical of a domestic amplifier with clear yet solid mid-range sound. In addition to the exterior, noticeable scuffs on the top plate, scratches on the VOL dial, and stains on the back of the front flap, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.2.16 Maintained (main volume, balance volume internal contact cleaning, cleaning. All input terminals are polished and cleaned, electrolytic capacitor replaced, PHONO2 impedance changeover switch disassembly, contact polishing, cleaning, and grease is applied. (Check the operation of each input/output)
Accessories: instruction manual (copy)
Main specifications: CR equalizer with 3 PHONO inputs MC head amplifier W455 x H132 x D357 mm 10.5 kg
RCA cable uses 1.5 m pair of out-of-print conductors and single crystalline high-purity oxygen-free copper PCOCCC with theoretically zero crystal boundaries for all core wires, braided wires, and plug pins. The shield is rolled up on the plug attachment part, it is dull, and there is a feeling of use (Kanai Hidetsugu)
Maintenance information: 2024.5.3 continuity confirmed
Roadie's representative 2-way speaker system. A luxurious magnetic circuit was added, and a machined aluminum horn tweeter of unusual quality for this size was used. Along with its elegant look, you can easily enjoy the thick domestic vintage sound. There are small scratches, stains, and warps on the top surface and side angles (Murakoshi Yoichi)
Maintenance information: 2024.2.17 sound output confirmed
Accessories: saran net
Main specifications: 2 way, 2 speakers, dumped bass reflex system, bookshelf type impedance, 8 ohms, output, sound pressure level, 88 dB, dimensions W360 x H610 x D340 mm, weight 22 kg
The price has been drastically reduced. 2024/1/20 sales price 99,800 yen ※The output terminals have been remodeled and 1 system has been added. This D/A converter has an impressive natural and supple texture. Another DAC board has been added to lock up to 48kHz. Equipped with a TOS optical input terminal, it is equipped with an Analog Devices 20-bit resolution DAC chip. It contributes to a rich amount of information. Soft and warm sound (Sasaki Shota)
Maintenance information: 2024.1.20 Operation confirmed
Accessories: power cord, BNC conversion plug
Main specifications: 20 bit 8 times oversampling 32 kHz, 44.1 kHz, 48 kHz digital input = BNC3 system, optical 1 system digital output = BNC1 system, TOS optical 1 system analog output = RCA1 system size W483 x H65 x D312 mm 5.5 kg
The price has been reduced! 2024/4/19 sales price 79,800 yen ※1 unit only. Maintained! It is originally a professional mono amplifier, but there is only 1 unit. You can feel the strong power of the sound quality even with just one unit. It seems to be useful for mono and center speakers. There are scratches and paint peeling on the exterior. Serial Q001769 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (XLR speaker cable created (3 meters)). Electrolytic capacitor replacement. ATT cleaning. Solder correction. Rubber feet added. Bias offset check. Output audio check. Input ① GND ② HOT ③ GND (unbalanced) output ① not used ② is set to plus ③ minus 8 Ω load. (Also, a pop sound is made when the power is on and off, but this is a specification)
Accessories: speaker cable, power cable
Main specifications: 8 ohms W482.6 x H88 x D320 mm weight 13 kg
Video digital cable, 1.0m, RCA terminal, SP-LGC conductor, entry model for the company's digital cable. There is a big difference in sound just by replacing it with a general-purpose digital cable (Kojima Yosuke)
Accessories: original box
The price has been drastically reduced. 2024/4/16 Sales price 118,000 yen Manufacturer maintained! Marantz pre-main made as an amplifier compatible with super audio. The sound, which makes you feel more relaxed and warm than recent models from the company, which have sharp looks, is attractive. The phono is also MM/MC compatible, so there are no omissions. Dullness, there is a small scratch on the top plate (Sasaki Shota)
Maintenance information: 2024.4.16 manufacturer maintained (SP relay defect replacement, front VR main relay nuclear circuit Iida defect correction implementation, other operation inspections)
Accessories: manual, power cable, remote control
Main specifications: 100W+100W (8Ω) Playback frequency band: 5Hz to 100kHz Analog input: 7 systems Analog output: 2 systems Dimensions W458 x H166 x D464 mm Weight 23.0 kg
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
The disposal price has been reduced. Member discounts are not applicable. 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg