Both the interior and exterior have been maintained and brushed up! The OLYMPUS S8R representing JBL has arrived. The combination of thick, dry low frequencies, the sound of a driver that seems to blow fire, and the 075, which leaves a gritty feeling of realism, is impressive. Please enjoy the real thrill of vintage audio. The exterior is also beautifully finished (Yonejima Satoshi)
Maintenance information: 2024.5.11 Maintained (network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/screw replacement, exterior cleaning. Woofer maintenance: edge replacement, cone paper coating, passive cone paper coating. Exterior repair/polishing/oil finish, front and rear baffle/hakama repair/painting. Lattice repair/polishing/painting, lining replacement. (Detaching the unit, repairing the diffuser)
Accessories: saran net
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1,020 x H670 x D510 mm weight 82 kg
Maintained! Original Model 7 You can enjoy a glossy mid to high range sound with a high sense of transparency and a thick, exquisite balance. It's a model that has been over half a century since it went on sale for analog fans, but it's still one they admire. The lustrous, indescribable tone is an appeal that cannot be enjoyed on modern devices. You can see a feeling of use, such as appearance, dullness, small scratches, etc. Serial 7-14836 (Kobayashi Hitoshi)
Maintenance information: 2023.5.20 maintained (balance volume B curve → MN curve replaced, block capacitor, 50 μF x 3, oil capacitor, 0.1 μF, other deterioration replacement, 8 electrolytic capacitors, 200 μF deterioration replacement, 2 vacuum tubes, 12AX7 deterioration replacement, 2 shield case replacement, high pressure selenium deterioration countermeasures → diode addition, side pad deterioration exchange, vacuum tube socket and RCA jack caulking repair, etc. Operation has been checked with AC 100 to 117 V)
Accessories: none
Main specifications: tubular control amplifier, vacuum tube, ECC83/12AX7, 3-stage NF equalizer, NF type step switching control, W453 x H185 x D267 mm, weight 7.5 kg
Maintained! An original C22, a famous machine admired by enthusiasts. The thick, soft, and strongly extruded tone is a pleasant tone that can only be experienced with an old McKinn. It has a rich tone centered around the middle range with a high concentration, and it sounds with plenty of realism. The exterior has a feeling of use such as dullness and small scratches. Serial 44A12 (Hiroki Aso)
Maintenance information: 2024.5.19 maintained (main volume A curve replaced with the original vacuum tube 12AX7 noise replacement oil capacitor 0.01 μF domestically manufactured in the USA) replacement block capacitor 40/20/20/1000 μF other defective and deterioration replacement electrolytic capacitor 1000 μF additional electrolytic capacitor 40 μF other deterioration replacement switching noise reduction measures 1/4 W additional resistance 1/2 W deterioration replacement short (Additional pin vacuum tube socket, RCA jack caulk repair, and other operation checked with AC 100 to 117 V)
Accessories: A copy of the English instruction manual
Main specifications: 117 V specification, 4 input systems, 2 phono systems, frequency characteristics, 20 Hz to 20 kHz (± 0.5 dB), signal-to-noise ratio, 85 dB (high level), 62.5 dB (low level), distortion ratio 0.2%, W406 x H138 x D330 mm, 7.3 kg
Maintenance has been completed, such as replacing capacitors and replacing deteriorated parts! It is a famous machine with a velvet transformer, and you can enjoy rich sound with stable operation. The fresh, glossy tone in the mid-high range has a different appeal from the MC275. The exterior has a feeling of use over time, such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.19 Maintained (volume curing improvement treatment for TWIN, 2W oil capacitor replaced with 0.01μF, 3W oil capacitor replaced with 0.5 μF, missing thermistor, replacement, 250μF, domestic CE replacement, block capacitor 100/30 μF defective replacement, oil capacitor 0.22 μF defective replacement electrolytic capacitor 20μF, etc. Deterioration replacement resistor 2W deterioration replacement Vacuum tube socket and RCA jack caulking repairs ※ Other operation checks have been performed (measured at 41 to 58 W with rated output AC 100 to 117 V, SP: 8 Ω) ※ The power transformer groans a little, but there is no problem with performance)
Accessories: A copy of the English instruction manual
Main specifications: 40W+40W 6L6GCPP vacuum tube 6L6GC × 4 12AX7 × 3 12AU7x2 12BH7 × 2 frequency characteristics 16 to 40,000 Hz dimensions W400 × D265 × H195 mm weight 25 kg
The price has been drastically reduced. 2024/5/10 sales price 498,000 yen Both inside and outside have been maintained! Crescendo is a speaker system developed by Electri and sold with Altech's approval. This time it's an original original box specification with the 605B mounted on it. You can enjoy the tasteful design unique to vintage speakers and the crisp American sound with good texture and momentum. The exterior is also beautifully finished due to maintenance, but there are repair marks on the net (Sasaki Shota)
Maintenance information: 2024.5.10 Maintained (exterior cleaning/touch repair. Network assembly) 2023.9.3 maintained (exterior repair/polishing/clear finish front and rear baffle repair/paint saran net simple cleaning
Unit maintenance (low range side: viscoid adjustment/center adjustment, high frequency side: lead disconnection repair, magnetic circuit rust removal/gap cleaning/center adjustment, terminal contact cleaning) network maintenance (characteristic check, terminal cleaning) unit detachment)
Accessories: none
Main specifications: frequency characteristics 20 to 20,000 Hz, use unit 38 cm, 605B (coaxial type with built-in horn), maximum input 50 W, output sound pressure level 97 dB, crossover frequency 1.6 kHz, impedance 16 Ω
W690×H1018×D485mm
The price has been drastically reduced. 2024/5/10 sales price 468,000 yen Maintained! By installing a double 10-inch (25cm) diameter woofer while equipped with a traditional JBL horn and compression driver, a slim tall boy style is achieved with sufficient low frequency energy. It is an excellent speaker that combines low frequencies with instantaneous power typical of JBL and sharp mid-high frequencies. The exterior is good with no noticeable scratches (Shota Sasaki)
Maintenance information: 2024.5.10 Maintained (magnetic fluid removal/cleaning/center adjustment in the single-sided driver magnetic circuit gap)
Accessories: none
Main specifications: 3-way 4-speaker woofer 100FE-12 scoker 175Nd-3 tweeter 139 Nd playback frequency band 33 Hz to 40 kHz crossover frequency 850 Hz/12 kHz impedance 6 Ω output sound pressure level 92 dB allowable input 250W (RMS) W370 x H1,007 x D368 mm 39 kg
The price has been drastically reduced. 2024/4/25 sales price 448,000 yen Maintenance is being carried out in 2020. It's a famous machine you can't miss when talking about Marantz sounds of yesteryear. It has a good mid-range fat transfer, and its pleasant sound is an appeal that cannot be obtained anywhere else. You can enjoy the Marantz sounds of the good times. There is some rust and small scratches on the exterior. Serial 8-4160 (Murakoshi Yoichi)
Maintenance information: 2020.11.18 maintained (AC code deterioration replacement, 40/40/20 μF and other deterioration replacement, 3 external paint, 20 μF x 2 deterioration replacement, selenium deterioration countermeasures → diode addition · vacuum tube 6BH6 noise exchange · vacuum tube socket and RCA jack caulking repair ※ other operation checked (measured at 32 to 41 W SP: 8 Ω with rated output AC 100 to 117 V) *A2 The EL34 vacuum tube guide pin is broken, but there is no problem with performance. (Part of the SP terminal on the right channel is missing.)
Accessories: instruction manual (for replicas, Japanese copy)
Main specifications: 35W+35W vacuum tube 6CG7/6BH6/EL34 W348 × H191 × D273mm 22.5 kg
The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its rich sound. The extrusion is strong and goes great with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. There are scratches, dullness, and discoloration in places (Kojima Yosuke)
Maintenance information: Maintained on 2020.8.26 (2 input volumes, 4 semi-fixed volumes, 2 RCA plugs, 12 lamps, 8 electrolytic capacitors, replacement input mode switch disassembly cleaning, card edge cleaning, soldering, bias and offset check, output sound check)
(*The interior and exterior have been cleaned.)
Accessories: power cable
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
Both inside and outside have been maintained! This is an ultra-rare speaker Allegro equipped with Monitor Gold. This bookshelf is almost the same size as a 3LZ. It is an attractive speaker with a beautiful sound unique to Monitor Gold and a mid-low range resolution that is a bit different from 3LZ. It lets me listen to quality that is compatible with everything. Serial SG1515/SG1517 (Yonejima Satoshi)
Maintenance information: 2024.5.12 maintained (saran net reinstallation/resonance prevention measures, unit maintenance: magnetic circuit gap cleaning/center adjustment for both low and high frequencies, network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning, 4-pin direct connection modification repair. Exterior repair/polishing/oil finishing, rear baffle repair/painting)
Accessories: No accessories
Main specifications: unit using a coaxial 2-way bass reflex speaker system 12 inch MONITOR GOLD coaxial 2-way playback frequency band 25 Hz to 20 kHz maximum input 15 W input impedance 8 Ω crossover frequency 1 kHz dimensions W380 x H583 x D 240 mm weight 16.2 kg (actual measurement)
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/7 sales price 398,000 yen Exterior maintenance completed! Replace network capacitors with SOLEN film capacitors. The unit is DENTECH Tune HDP385, and the enclosure is made by Shinkosha. The unit is attached by removing the back plate, and the net does not come off the front. Classical music also goes well with symphonies. The exterior is generally beautifully finished due to maintenance. Serial AYT71012 AYT71012 (Tomonori Asaine)
Maintenance information: 2024.3.7 Maintained (exterior repair/cleaning
Rear baffle paint saran net replacement unit maintenance (exterior cleaning, low range center adjustment, screw tightening, high frequency magnetic circuit slit cleaning/center adjustment) ATT cleaning/knob adjustment unit detachment)
2015.5.14 Maintained (network capacitors replaced with SOLEN. Unit edge replacement. Magnetic circuit overhaul and operation adjustment. Saran net partial cleaning net tear repair, complementary color correction)
Accessories: none
Main specifications: used unit HPD385 frequency characteristics 20Hz to 20kHz allowable input 85W 92dB 8Ω W600 x H1075 x D380 mm approx. 42 kg/bottle
Both the interior and exterior have been fully restored and refreshed! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. It is beautiful due to exterior repairs (Sasaki Shota)
Maintenance information: 2024.5.10 Maintained (exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting. Saran net replacement/frame repair/reinforcement. Unit maintenance: low range/edge exchange, magnetic circuit gap cleaning/center adjustment, high pass/magnetic circuit rust removal/gap cleaning/center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, faston terminal replacement, terminal cleaning)
Accessories: none
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
The disposal price has been reduced (member prices are not applicable). 2024/2/16 sales price 378,000 yen ※The power supply part has been newly created. Other internally deteriorated parts have been restored! 2-way 100Hz specification An electric crossover coveted by Mark Levinson fans. You can see how well the early Levinson was built can be seen from the feel of the knobs that seem to make you addicted. You can listen closely to Levinson's unique sounds even on Divider. The exterior has scratches on the front top plate and other threads (Mizusaki Ryo)
Maintenance information: 2024.2.16 Maintained (*Since there is no power source, new power supply and connection cable were manufactured, noise appears in the LChLow output, transistor defects in the low pass module were replaced, re-encapsulated, readjusted due to left and right level differences, 4 volume contacts were cleaned, specs were inspected, and blocking characteristics were inspected. The crossover is 100Hz)
Accessories: Power supply unit (newly created, non-genuine), power cable, copy of instruction manual
Main specifications: 2 way (100 Hz specification) closed module type RCA Remo input/output size (main unit) W483 x H51 x D156 mm 2.8 kg size (power supply part) W101 x H101 x D256 mm 2.2 kg
Refresh yourself with internal and external maintenance! This is an attractive mid-size model with the large 38cm HPD385 unit pressed into a compact enclosure. It has good phase characteristics and plays classical music and vocals in a pleasant tone with a high texture and a good, moist tone (Mizusaki Ryo)
Maintenance information: 2024.5.11 Maintained (exterior repair/cleaning
unit assembly)
2019.12.30 Maintained (input terminal rust removal (pickling) treatment, cleaning. Internal connection terminal (faston) replaced with a new one. Output terminal polish cleaning. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Exterior repair/polishing/oil finish. Front and rear baffle/hakama paint Saran net replacement. Unit maintenance (low range side: edge exchange, magnetic circuit gap cleaning center adjustment, high range side: magnetic circuit gap cleaning center adjustment) unit detachment)
Accessories: none
Main specifications: coaxial 2-way speaker, front bass reflex system, 8Ω, 91 dB, W540 x H840 x D310 mm, 32 kg
The price has been drastically reduced! 2024/4/27 sales price 298,000 yen Interior and exterior maintenance completed! English studio monitor with TANNOY HPD385 installed. It's deep and you can feel that the scale is wide, and the size is clean, so the room's layout will expand. The exterior has been beautifully finished due to maintenance (Tomoho Asaine)
Maintenance information: 2024.4.27 Maintained (exterior cleaning/repair
Saran net replacement unit maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, fastener polishing) unit detachment network maintenance frequency characteristic check ATT cleaning high range capacitor replacement (3.3 uf, 4.8 uf) 4 pin terminal contact cleaning)
Accessories: none
Main specifications: size W510xH769xD380mm weight 32.2 kg (actual measurement)
2018 fully restored item. This model omits the MC step-up transformer. The rear speaker terminal has also been changed to one compatible with banana plugs to match modern usability. Although it is a model from the 60s, there is no sense of a faded sound, and it feels like the flat, thick lackstone has been revived energetically. The sound without getting tired even after listening to it for a long time makes me fully experience the luster and warmth of stringed instruments. There are stains all over the exterior, and there are line scratches, fading, etc. on the cabinet (Sasaki Shota)
Maintenance information: 2018.8.25 Maintained (9P socket, SP terminal, RCA terminal, block capacitor, volume/BAL/TCVR, semi-fixed resistor, coupling capacitor, AC cord, resistor replacement. Power SW contact deterioration prevention relay added. SW/VR disassembly, cleaning, solder correction. (Internal and external cleaning, circuit readjustment, waveform check, input/output check, load test, sound output test)
Accessories: copy of the manual
Main specifications: output 10W+10W input terminal AUX1 · 2 Phono 1 · 2 (mm) W470 x H175 x D275 mm weight 14 kg
Full maintenance, such as internal and external maintenance, was carried out, and the finish was beautiful! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. Serial 55553L, 55553R (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (exterior repair/repaint) 2017.4.25 Maintained (exterior polishing/all coated woofer cone paper/unit frame paint chip putty repair grill dent correction/paint tweeter distortion and maintenance (edge deformation repair, magnetic circuit slit maintenance complete) unit detachment terminal replacement (banana plug compatible product) ATT cleaning capacitor replacement*Some capacitors before replacement Since it is difficult to remove, remove the wiring to check the remaining input/output waveform and balance, sound output check, frequency characteristic measurement check (~ 42 kHz)
Accessories: No accessories
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
Internally and externally maintained! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. There is a very slight dent in the tweeter grill, and there are repair marks on the side (Murakoshi Yoichi)
Maintenance information: 2024.3.4 maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network frequency characteristic check, ATT cleaning, terminal replacement)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
The disposal price has been reduced! Member prices are not applicable. 2024/4/6 sales price 218,000 yen ※The exterior is in poor condition, so it's cheap. Maintained! 100V specification genuine Baes product. A control amplifier representing the golden age of Macintosh. Compared to the C28, this model has a wider range and more subtlety. The rich, glossy, and thick tone is alive and well, especially with vintage speakers. The exterior has rust spots, paint deterioration, and unevenness on the front. Serial JBZ7419 (Fujisawa Yukishi)
Maintenance information: 2024.4.6 maintained (TONE, MODE, INPUT, BAL etc. disassembly contact polishing grease applied. All push switch contacts are coated with abrasive grease. Mode switch, volume, balance volume contact cleaning. Electrolytic capacitor replacement. Panel lamp replacement Panel peeling correction. ※Since the panel color is burnt, there is color unevenness with the correction part. (Check the operation of each input/output)
Accessories: No accessories
Main specifications: frequency characteristics 20 Hz to 20 kHz input terminals PHONO 1 · 2, AUX, TUNER, TAPE 1 · 2 W406 × H138 × D330 mm 8.6 kg
Maintained in 2023. After all, the warm, and glossy sound quality is excellent for stringed instruments. It has a soft and vivid sound not found in transistors, making it perfect for listening for long periods of time. In addition to noticeable scuffs and paint peeling on the exterior and transformer area, dullness and a feeling of use can be seen. Serial F0800283 (Murakoshi Yoichi)
Maintenance information: 2023.7.23 maintained (vacuum tube socket block capacitor electrolytic capacitor oil capacitor SP and RCA terminal semi-fixed VR fuse holder replacement load test (8Ω load 1kHz 25W+25W) input/output waveform confirmation sound output check performed gain VOL NFB switching SW disassembly contact refinement to prevent oxidation and sulfation grease coating input/output waveform confirmation distortion load test (1 kHz (25W+25W at sine wave 8Ω load) sound output test)
Accessories: copy of instruction manual
Main specifications: 50CA10 push-pull output 30W+30W W410 x H183 x H160 mm 13.8 kg
The A2500 is a tube type power amplifier kit that has been replaced with speaker terminals that are easy to use even for beginners. 6AQ8 for the first stage and 12AU7 for the phase reversal stage both use triodes. Since triodes are used across all stages, the sound is taut and bright, with excellent nude characteristics. The exterior has dullness over time, rust, and small scratches. Serial 560561 (Miura Kimiya)
Maintenance information: 2018.4.28 Maintained (printed circuit board resistor replaced. (Adjustment characteristics check OK) 2014.11.21 maintenance completed (input VR, vacuum tube socket, coupling capacitor, SP terminal, BIAS DC BAL, semi-VR, each deterioration exchange, adjustment, characteristic check OK)
Accessories: instruction manual
Main specifications: 6 RA8 push-pull 6 RA8 x 4/12 AU7 x 2/6AQ8 10W+10W W410 x H145 (with hood) x D190 mm 9.6 kg
Fully maintained! The main part of the SQ38F is an independent power amplifier, the famous MQ60. The natural, smooth sound quality with a high sense of transparency is attractive. You can relax and enjoy classical music and vocals in a natural way. The deep sound quality that cannot be expressed with the latest vacuum tube amplifiers is exceptional. The exterior has dullness, small scratches, and paint peeling. Serial 473753 (Hiroki Aso)
Maintenance information: 2024.5.19 maintained (vacuum tube socket block capacitor electrolytic capacitor oil capacitor SP and RCA terminal semi-fixed VR fuse holder replacement load test (8Ω load 1kHz 30W/30W) input/output waveform confirmation sound output check performed impedance switching SW gain VOL disassembly contact refinement oxidation and sulfidation prevention grease coating input/output waveform confirmation load test (1 kHz) (Sine wave at 8Ω load: 30W+30W) sound output test)
Accessories: copy of instruction manual
Main specifications: output 30W+30W dimensions W410 x H160 x D205 mm weight 13.8 kg
The A3500 vacuum tube power amplifier has been refreshed by thorough maintenance down to the smallest details, such as volume disassembly and polishing. The warm, fresh tone, filled with the appeal of a vacuum tube type, is still appealing enough today. You can enjoy music with a rich, thick tone that contrasts with the clicking tones of recent vacuum tube amplifiers. As for the exterior, paint deterioration and peeling can be seen on the transformer on one side, and there is a feeling of use such as dullness, small scratches, etc., and there is a dent in the hood. ※3-pole tube connection specification. 20W+20W (actual measurement) is output as specified by the manufacturer (Takasaki Atsushi)
Maintenance information: 2023.2.3 maintained (main tube (6CA7) replacement vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, complete disassembly of semi-fixed VR replacement power input gain volume, contact polishing, anti-oxidation/sulfation grease coating load test (8Ω load 1kHz 20W+20W) input/output waveform confirmation sound output check performed)
Accessories: copy of the manual
Main specifications: 20W+20W (8Ω) vacuum tube 6CA7×4/6AQ8×3 W465×H168×D206mm 16kg
*The arm base is convenient, and the mounting position of the arm is slightly close to the shaft side. Since the arm is long, please remove the dust cover for playback. Comes with SAEC arm stabilizer AS-500! A record player that is highly regarded for its smooth rotation and the effectiveness of the insulator's suspension. The WE-308 arm features a double knife edge for sharp sound and accurate sound image localization. It is a combination of LUX's smooth and quiet motor and SAEC arms that cut sharply into the sound source, so you can fully enjoy the fun and depth of analog. Additional rubber feet have been attached to the legs to prevent the AS-500E. The exterior is dull and has small scratches. Serial G8903281 (Murakoshi Yoichi)
Maintenance Information: 2020.6.2 Maintained (created with strobe circuit LED. diode installation. Electrolytic capacitor replacement. Power circuit film capacitor replacement. (Inside Force cancellation weight exchange)
Accessories: phono cable
Main specifications: PD-131 direct drive system 8 pole 24 slot brushless DC servo motor W472 x H160 x D372 mm weight 12 kg WE-308 double knife edge static balance universal type total length 329 mm effective length 240 mm overhang 5 mm needle pressure 0 to 2 g cartridge weight range: 5.5 to 12.5 g
The disposal price has been reduced. Member discounts are not applicable. 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg
Maintained! Micro belt drive middle class player. Coupled with a 3.2 kg heavyweight platter, the tone is extremely quiet and smooth. The cabinet is also highly rigid, leading to a thick, analog-like sound quality that comes out well. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 21120262 (Jun Tamai)
Maintenance information: 2024.5.19 Maintained (motor bearing oil replacement deteriorated parts (electrolytic capacitor semi-fixed resistance rectifier diode) replacement tone arm disassembly/shaft bearing replacement lifter disassembly/grease up speed switching SW rotation fine adjustment volume disassembly/contact polish since the insulator has deteriorated, replaced with a replacement product turntable rotation speed confirmation arm operation needle pressure confirmation exterior cleaning sound output test (Other operation confirmation dust cover newly created)
Accessories: instruction manual overhang gauge
Main specifications: belt drive type static balance type tone arm needle pressure variable range 0 g to 3 g compatible cartridge dead weight 11.5 g to 21 g (including shell) W510 x H155 x D400 mm 13 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg
Maintained! A popular DENON control amplifier for its excellent phono equalizer. MC head amplifiers are famous for their quality, and they fully draw out the amount of information in the cartridge. It's a neat sound typical of a domestic amplifier with clear yet solid mid-range sound. In addition to the exterior, noticeable scuffs on the top plate, scratches on the VOL dial, and stains on the back of the front flap, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.2.16 Maintained (main volume, balance volume internal contact cleaning, cleaning. All input terminals are polished and cleaned, electrolytic capacitor replaced, PHONO2 impedance changeover switch disassembly, contact polishing, cleaning, and grease is applied. (Check the operation of each input/output)
Accessories: instruction manual (copy)
Main specifications: CR equalizer with 3 PHONO inputs MC head amplifier W455 x H132 x D357 mm 10.5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/15 sales price 128,000 yen LINN network audio player with an integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1234701 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/15 sales price 128,000 yen LINN network audio player with an integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1220444 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
The price has been drastically reduced. 2024/4/16 Sales price 118,000 yen Manufacturer maintained! Marantz pre-main made as an amplifier compatible with super audio. The sound, which makes you feel more relaxed and warm than recent models from the company, which have sharp looks, is attractive. The phono is also MM/MC compatible, so there are no omissions. Dullness, there is a small scratch on the top plate (Sasaki Shota)
Maintenance information: 2024.4.16 manufacturer maintained (SP relay defect replacement, front VR main relay nuclear circuit Iida defect correction implementation, other operation inspections)
Accessories: manual, power cable, remote control
Main specifications: 100W+100W (8Ω) Playback frequency band: 5Hz to 100kHz Analog input: 7 systems Analog output: 2 systems Dimensions W458 x H166 x D464 mm Weight 23.0 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/2/10 sales price 198,000 yen Maintained! According to the 117V specification of the tubular mono FM tuner, reception is unstable at 100V. The Japanese band has been changed, and reception sensitivity is good. It is a tuner that strongly shows the characteristics of Mackin's sound, which is thick, soft, and glossy. There is corrosion and rust throughout the exterior. Serial 292099 (Tomoho Asaine)
Maintenance information: 2024.2.10 Maintained (meter readjustment with coil and right side volume, left side lamp off replacement, IF/RF/MPX readjusted)
2018.2.22 Maintained (VT12AT7 replacement/MPX section transistor replacement/RF/IF/MPX re-adjustment)
2016.1.25 Maintained (6 additional VT shortages. 2 VT replacements 4 additional ceramic C for BAND EX Ceramic C replacement. Chemical C exchange. Front lamp repair, block.C50uf x 4 replacement Step up transformer 100V ⇒ 117V added)
Accessories: 117V step up transformer
Main specifications: FM dedicated tuner W400 x H130 x D300 mm 8.6 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/3/22 sales price 128,000 yen Maintained! Quad power amplifier Despite its compact body, you can enjoy a smooth, thick sound. It really goes well with speakers made in England, and makes you listen to 70s analog sound with a sense of dynamism. The exterior has a feeling of use such as dullness. Serial 41000 (Tomoho Asaine)
Maintenance Information: 2024.3.22 Maintained! (Internal check DC cut C, gain setting C, etc., exchange Tr, etc. check operation check, DIN4P-RCA female cable creation)
Accessories: power cable
Main specifications: 100W+100W frequency characteristics 20 to 20 kHz dimensions W341 x H115 x D195 mm weight 9 kg
The price has been reduced! 2024/5/16 sales price 99,800 yen Maintained! A speaker that allows you to enjoy the powerful sound of JBL. A vertical twin that uses bi-radial horns for the tweeter and is developed with upper and lower 20cm woofers. Sound pressure, which is characteristic of horns, is uniformly distributed within the area, and you can experience a wide service area. The exterior has been beautifully finished due to maintenance. Serial 5340-015070 5340-015071 (Asaine Tomoho)
Maintenance information: 2024.5.16 Maintained (exterior cleaning/touch-up saran net cleaning/frame repair/paint tweeter maintenance (magnetic fluid removal/cleaning/center adjustment in the magnetic circuit gap, left and right sound pressure difference adjustment, internal urethane replacement) woofer maintenance (edge replacement, gasket preparation and installation) unit detachment)
Accessories: saran net
Main specifications: output sound pressure level 92 dB frequency characteristics 35 Hz to 20 kHz W318 x H965 x D413 mm weight 34 kg
The price has been drastically reduced. 2024/1/20 sales price 99,800 yen ※The output terminals have been remodeled and 1 system has been added. This D/A converter has an impressive natural and supple texture. Another DAC board has been added to lock up to 48kHz. Equipped with a TOS optical input terminal, it is equipped with an Analog Devices 20-bit resolution DAC chip. It contributes to a rich amount of information. Soft and warm sound (Sasaki Shota)
Maintenance information: 2024.1.20 Operation confirmed
Accessories: power cord, BNC conversion plug
Main specifications: 20 bit 8 times oversampling 32 kHz, 44.1 kHz, 48 kHz digital input = BNC3 system, optical 1 system digital output = BNC1 system, TOS optical 1 system analog output = RCA1 system size W483 x H65 x D312 mm 5.5 kg
The disposal price has been reduced. Member prices are not applicable. 2023/12/30 sales price 100,000 yen Maintained! D/A converter incorporating a 20 bit DAC chip manufactured by Barbrown. The mellow tone is attractive. It adds an analog-like nuance to the sound of the CD. The exterior is dull and has small scratches (Oikawa Tetsuji)
Maintenance information: 2023.12.30 Maintained (replacement solder and pattern correction board electrolyte cleaning due to loss of exchange resistance due to electrolyte condenser fluid leakage, input/output voice check for each FS)
Accessories: none
Main Specifications: Barb Brown 20-bit heavyweight toroidal power transformer W430 × H70 × D280 mm 7.5 kg
The price has been reduced! 2024/4/19 sales price 79,800 yen ※1 unit only. Maintained! It is originally a professional mono amplifier, but there is only 1 unit. You can feel the strong power of the sound quality even with just one unit. It seems to be useful for mono and center speakers. There are scratches and paint peeling on the exterior. Serial Q001769 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (XLR speaker cable created (3 meters)). Electrolytic capacitor replacement. ATT cleaning. Solder correction. Rubber feet added. Bias offset check. Output audio check. Input ① GND ② HOT ③ GND (unbalanced) output ① not used ② is set to plus ③ minus 8 Ω load. (Also, a pop sound is made when the power is on and off, but this is a specification)
Accessories: speaker cable, power cable
Main specifications: 8 ohms W482.6 x H88 x D320 mm weight 13 kg
Speaker cable, 1.5 m pair by wire specification, EQB8, Y lug specification at both ends, 7N-OCC Copper conductor top model, high CP cable with sound quality close to Eclipse 8 while keeping the price low. This cable is excellent for SN and has just the right amount of softness for sound (Kojima Yosuke)
Accessories: special case
A network adapter that converts USB 3.0 to SFP (only compatible with 1 Gbps) SFP ports can be added to Windows PCs or laptops without wired LAN ports. There is a line scratch on the bottom. *SFP module and 5V power adapter are sold separately. (FUJISAWA KOSHI)
Accessories: original box
Key specs: https://www.oliospec.com/shop/shopdetail.html?brandcode=000000010613&search=USB-SFP&sort =
M/MC compatible A tubular phono equalizer developed with the aim of better analog reproduction. You can enjoy a warm, natural sound using a vacuum tube non-feedback amplifier and a CR-type equalizer. The impedance can be switched according to the cartridge. Externally, there are line scratches on the top plate. Serial 00180 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: power cable
Main specifications: MM/MC compatible 12AX7 (ECC83) x 2 W300 x H100 x D260 mm 4.8 kg
MC cartridge compatible with EMT arms by attaching the SPU body and Audiocraft adapter OF-3A to the modified headshell. You can enjoy the gorgeous and expansive sound typical of an orthophone with the EMT arm. The cantilever is moving very slightly to the right (Murakoshi Yoichi)
Maintenance information: 2024.5.10 sound output confirmed
Accessories: none
Main specifications: MC type output 0.2 mV for EMT arms, proper needle pressure 4 g, internal impedance 2 ohms, dead weight 24 g
The price has been drastically reduced. 2023/11/8 sales price 49,800 yen ※The display panel moves when the volume etc. switch is pressed, but this is a specification. Maintained! MICROMEGA D/A CONVERTER It's a well-balanced European tune, and you can listen to chamber music and vocals smoothly. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.9.3 Maintained (replacement of tantalum electrolytic capacitors, replacement of other capacitance electrolyzed capacitors. Various digital signal demodulation tests confirm normal operation. (Rubber foot replacement)
Accessories: none
Main specifications: 1-bit input sampling frequency 32kHz,44.1kHz,48kHz W220×H55×D110mm 1.5kg
The price has been reduced. 2024/5/10 sales price 42,800 yen This 2-way bookshelf with monitor audio will be introduced for the first time at Hi-Fi. The C-CAM unit introduced in the Bronze Series pursues sound quality. The high cost performance and sound typical of the company are attractive (Murakoshi Yoichi)
Maintenance information: 2024.5.10 sound output confirmed
Accessories: instruction manual, saran net, bass reflex sponge, jumper, rubber feet, original box
Key Specifications: 2 Way 8Ω 85dB Crossover 2,500Hz W166 × H281 × D268 mm 5.0 kg
The stylus is good, but since the cantilever is curved, it is inexpensive. A mono-only cartridge with a traditional 33 series body. Play mono records clearly with a pick-up that is only horizontally oriented. It has vertical compliance and is optimized for recurrent mono editions in the stereoca era. The range is wider than Denon's DL-102 and you can feel the expansion (Fujisawa Yukishi)
Maintenance information: 2023.8.29 Operation confirmed
Accessories: needle cover
Main specifications: MC type needle pressure 2.3 to 2.7 g (2.5 g standard) Muku round needle high hardness duralumin cantilever PCOCC coil anti-vibration rubber “honeynight” impedance 10 ohms 6.9 g
Mono exclusive MC cartridge. It's not flashy, but it stretches and makes a gentle sound that is pleasant. There is a feeling of use such as dullness (Daiki Goto)
Maintenance information: 2024.5.13 operation confirmed
Accessories: original box, instruction manual
Main specifications: MC type 0.5 mV needle pressure 2.5 to 4.5 g dead weight 5 g
DENON's classic MC cartridge. The balance of localization and sound is excellent, and all music genres can be played without difficulty. I can recommend this cartridge to a variety of people, from analog beginners to experts (Murakoshi Yoichi)
Maintenance information: 2024.5.8 sound output confirmed
Accessories: needle cover, case
Main specifications: MC type output voltage 0.3 mV playback frequency 20 Hz to 45 kHz electrical impedance 40 ohms needle tip 16.5 microns round needle pressure 2.2 to 2.8 g dead weight 8.5 g
Pair tube, 6L6GC compatible ball, high reliability tube, made in America lot: 8526/8526 measured value 44/42 (rejected value 25) with replacement box ※ pair is determined based on GM values measured with test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
GT SONIC's compact ultrasonic cleaner for commercial use. It's not for audio only, but it seems that it can be used for quite a variety of purposes. I think the size is good too. If you've been looking for one, take this opportunity. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: power cord, original box
Main specifications: ultrasonic power consumption 150 W power supply AC 100-120 V 50/60 Hz ultrasonic frequency 40,000 Hz cleaning tank size: W155 x H150 x D300 mm body size: 180 x 310 x 330 mm 5.9 kg
Balance cable, 0.7 m pair, PC-Triple C conductor, conductor with stable electrical characteristics such as ultra-low distortion ratio and high conductivity, and double shielding for perfect noise countermeasures. It has an edgy, well-cut sound using a gold plated plug made by Neutrik. The lettering is frayed and thinned. (FUJISAWA KOSHI)
Maintenance information: 2024.5.12 continuity confirmed
Accessories: No accessories