※1 bottle only. A full range unit that combines an aluminum alloy HR diaphragm and a pure magnesium ridge dome diaphragm. Compared to conventional paper units, it has a slightly better transparency and microwave feel. The exterior is stained with corn paper, paint marks and scratches on the frame (Satoshi Yonejima)
Maintenance information: 2024.5.6 sweep test is good
Accessories: original box
Main specifications: impedance 4 ohms minimum resonance frequency 72 Hz playback frequency band F0 to 10 kHz output sound pressure level 85.5 dB
※1 bottle only. Fostex 1dB step transformer attenuator. It uses a large single-turn transformer and a highly reliable rotary switch with low contact resistance. The input/output terminals are tight-fitting. The exterior has oxidation, dullness, etc. (Tamura Eiji)
Maintenance information: 2024.5.8 operation confirmed
Accessories: none
Main specifications: 8Ω allowable input 100W (when using a network) attenuation 0 to 12 dB size W88 x H90 x D170 mm approx. 970 g
※1 bottle only. Super tweeter using an aluminum alloy thick cylindrical horn and an ultra-lightweight ring diaphragm. It expands the well-stretched, clean high frequency range. There are small scratches and dullness on the exterior. (YONEJIMA Satoshi)
Maintenance information: 2024.5.8 oscillator check is good
Accessories: pedestal, instruction manual
Main specifications: Alnico magnet, 8Ω, playback frequency band, 5kHz to 35kHz, output sound pressure level, 106dB, recommended crossover, 7kHz or higher, input 50W, 800g/book
Comes with a magazine! A full-range unit from Stereo magazine's 2016/8 appendix. Uses Fostex's first aluminum cone diaphragm and center cap. It features good sounding and sharpness. (FUJISAWA KOSHI)
Maintenance information: 2024.5.2 operation confirmed
Accessories: gasket, magazine (original box)
Main specifications: 8cm full range unit impedance 8 ohms minimum resonance frequency 105 Hz sound pressure level 82.5 dB
Flat speaker with 600 neodymium magnets. It is built into a self-made enclosure. It is an audio speaker that is mainly used outdoors for station announcements and as a large digital signage product for outdoor use. As for the exterior, there are screw holes in the top plate, and there are dullness and small scratches all over (Yonejima Satoshi)
Maintenance information: 2024.5.18 sweep test good
Accessories: No accessories
Main specifications: MCMA multi-cell flat speaker impedance 8Ω frequency specification 90Hz to 10kHz W270 x H375 x D205 mm 5.2 kg [actual measurement)
It is a USB-connected bus-powered D/D converter that uses the C-Media “CM6642” as the digital audio control IC and is compatible with high-resolution sound sources (maximum 24 bit/192 kHz) (Tamura Eiji)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, original box
Main specifications: digital input: USB TypeB terminal USB 1.1/2.0 compatible, USBAudioClass 1.0/2.0 compatible digital output: coaxial digital audio output (COAXIAL) optical digital audio input (square) compatible format: PCM maximum 24 bit 192 kHz W40 x H25 x 81 mm 90 g
The price has been reduced! 2023/5/9 sales price 39,800 yen This speaker is equipped with the AXIOM10 vintage unit. Early model with 16 ohms. You can enjoy bright vocals with a tasteful tone unique to vintage speakers. Please try playing it on a record. The exterior has dullness, small scratches, etc. (Satoshi Yonejima)
Maintenance information: 2024.5.9 sweep test is good
Accessories: No accessories
Main specifications: 25cm double cone type full range unit 20W 15/16Ω W453 x H800 x D318 17.7 kg (actual measurement)
This is a high quality line cord that takes advantage of the characteristics of 4266, a 1.0m pair of RCA cables with a four-core shield structure (Tamura Eiji)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Power cable 1.8 m PSE standard 5-core power cable using PCUHD and 4N-OFC. The plug is a 2P type that uses brass+rhodium plating. Thick, orthodox sound. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Power cable 1.8 m PSE standard 5-core power cable using PCUHD and 4N-OFC. The plug is a 2P type that uses brass+rhodium plating. Thick, orthodox sound. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Power cable 1.8 m PSE standard 5-core power cable using PCUHD and 4N-OFC. The plug is a 2P type that uses brass+rhodium plating. Thick, orthodox sound. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
The disposal price has been reduced! (Member prices are not applicable) 2024/4/28 sales price 99,800 yen D/A converter with a dual monaural configuration equipped with 2 “ES9038PRO” units. Using 3 Talema toroidal transformers, you can feel the creator's commitment. More natural sound can be reproduced. On the exterior, there are noticeable line marks on the top plate (Tamura Eiji)
Maintenance information: 2024.4.28 Operation confirmed
Accessories: power cable
Main Specifications: Coaxial/BNC/AES/Optical: PCM44.1k to 192 K/16 to 24 bit, DOP64 I2S Input: RJ45/HDMI PCM44.1K to 768K 24/32 bit DSD64 to DSD1024 DOP64 to 256 W430 x H80 x D335 mm Weight 5.4 kg
A low-cost clock generator that emits a high-performance master clock. It is recommended for those looking for expressive power with a precise amount of spatial information. By inputting a high-accuracy 10 MHz reference output obtained from a high-precision transmitter for measurement or military transmitters (using rubidium, cesium, GPS) not manufactured as an audio device to the external clock input terminal, it is possible to transmit an even more accurate master clock. The exterior is dull. (YONEJIMA Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: power cord
Main specifications: 2 clock outputs (BNC) 44.1 kHz/48 kHz magnification x 1/2/4 (maximum 44.1 to 192 kHz), 1 10MHz clock input system (BNC), size W190 x H56 x D220 mm 810 g
Disposal prices have been reduced! (Member discounts are not applicable) 2022/5/18 sales price 2,000 yen When used between an S-terminal AV noise filter device and a display, unnecessary noise is removed without deteriorating the amount of information or high frequency characteristics of the video signal at all, and the video signal is organized. The exterior is dull and dirty, and there are floating marks on the label. (TAMURA Eiji)
Maintenance Information: 2022.5.18 Continuity Confirmed
Accessories: There are no accessories
Set of 4 Use ICP damping spacers and IDS composites together as tuning goods to counteract speaker vibrations. *Cannot be used as a receiver for metal spikes. There are scratches and threads on the exterior (Yonejima Satoshi)
Accessories: No accessories
Main specifications: diameter 35 mm x 3 mm (thickness)
The price has been reduced! 2024/3/4 sales price 59,800 yen ※The diaphragm has been replaced with a genuine JBL D8R2425. Maintained! Representative of JBL's 1-inch driver units. The playback band is wide, so you can enjoy changing the network cross freely. The toughness, sound pressure, and full-bodied mid-high sound are appealing, which is unbelievable for some input. Scratch marks and paint peeling can be seen. Serial 62206, 62240 (Fujisawa Yukishi)
Maintenance information: 2024.3.4 maintained (diaphragm installation adjustment (diaphragm comes with D8R2425) genuine JBL product. (The pad dampener has been replaced.)
Accessories: No accessories
Main specifications: 1 inch driver, 500 to 20,000 Hz, 8 ohms, W145 x D97 mm, 5.1 kg/bottle
Both the interior and exterior have been maintained and brushed up! The OLYMPUS S8R representing JBL has arrived. The combination of thick, dry low frequencies, the sound of a driver that seems to blow fire, and the 075, which leaves a gritty feeling of realism, is impressive. Please enjoy the real thrill of vintage audio. The exterior is also beautifully finished (Yonejima Satoshi)
Maintenance information: 2024.5.11 Maintained (network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/screw replacement, exterior cleaning. Woofer maintenance: edge replacement, cone paper coating, passive cone paper coating. Exterior repair/polishing/oil finish, front and rear baffle/hakama repair/painting. Lattice repair/polishing/painting, lining replacement. (Detaching the unit, repairing the diffuser)
Accessories: saran net
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1,020 x H670 x D510 mm weight 82 kg
The price has been drastically reduced! 2024/5/5 sales price 218,000 yen A special edition model commemorating the 70th anniversary of JBL's founding. The latest version that has been refined over the traditional 4312 series. A 12-inch diameter woofer unit equipped with the advanced 4429 is used. It is an all-round speaker with a sense of energy and good range extension. The exterior is dull. Serial 3072/3073 (Yonejima Satoshi)
Maintenance information: 2024.5.5 sweep test is good
Accessories: saran net
Main specifications: 3-way bass reflex type 300mm woofer 125mm mid-range 25mm tweeter impedance 6Ω output sound pressure level 90dB frequency characteristics 44Hz to 40kHz W362 x H597 x D298 mm 25.2 kg
※Chips and oxidation are conspicuous in the horn part, so it is inexpensive. A tweeter representing JBL. It gives an expression with a greater sense of depth and breadth than 075. It has a punchy, dynamic sound quality, and is a model unique to this era that excelled in characteristics such as a sense of attack and horsepower. The exterior has dullness, rust, and scratches due to aging. Serial 33996/33998 (Yonejima Satoshi)
Maintenance information: 2024.5.13 good oscillator test
Accessories: No accessories
Main specifications: horn type ferrite magnet playback frequency band 2,500 to 15,000 Hz impedance 8 ohms output sound pressure level 110 dB diameter 119 x depth 94 mm weight 2.4 kg
※1 bottle only. Shorthorn used in the 43 series. It can also be built into an enclosure, but it makes you hear good sound even when attaching a driver and placing it on top of the enclosure. There are paint peeling and scratches on the exterior (Yonejima Satoshi)
Accessories: No accessories
Main specifications: 80 degrees horizontal orientation for 1-inch drivers, 45 degrees vertical, recommended crossover 1.2 kHz, baffle opening diameter 108 mm, depth 216 mm
※It is inexpensive because it is in poor condition such as chips or cracks. An acoustic lens mounted on JBL monitor speakers such as the 4343 series. By wearing it, the sound of the horn, which is too strong, is moderately diffused and calmed down. The exterior has dirt, cracks, chips, holes, etc. (Tamura Eiji)
Accessories: none
The price has been reduced. 2023/10/6 sales price 29,800 yen ※Since it is only 1 bottle, it is cheap. JBL professional 2" screwdriver. It is an item that continues to be used in large horn systems, etc. The quality unique to titanium diaphragms, the breathing of the vocals, and the high hat on the drums are all appealing, and the outstanding realism is appealing. The exterior has dullness, dirt, and scratches. Serial 31316 (Tamura Eiji)
Maintenance Information: 2023.10.6 Oscillator Test Good
Accessories: no accessories
Main specifications: slot diameter 5 cm, allowable input 100 W, sound pressure level 111 dB/W/m, frequency characteristics, 500 Hz to 20 kHz, crossover frequency, 500 Hz or more, 16 ohms, diameter 235 x depth 132 mm, 13.6 kg/1
Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. Serial 60878/74750 (Tamura Eiji)
Maintenance information: 2024.5.18 Maintained (diaphragm installation adjustment. Pad dampener, mounting screw rust replacement Wiring terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning, internal wiring cable replacement. DCR (74750/6Ω diaphragm no scratch) DCR (60878/5.7Ω diaphragm no scratch))
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Maintained in October 2022! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, paint is bald and oxidized (Yonejima Satoshi)
Maintenance Information: 2022.10.7 Maintained (Terminal rust removal, acid cleaning, insulation bushing & mounting screw replacement. ATT replacement A frequency characteristic measurement check (~ approx. 42 kHz) was performed, and the original capacitor was continuously used for good results. Input/output waveform and balance check, sound output check.)
Accessories: no accessories
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
Maintained on 2015.6.11. The graininess of the sound has been clarified, and the smoothness of the connection has also been improved. It is a crossover 1200 Hz network ideal for the combination of a 38 cm woofer and 1 inch driver. The exterior has paint peeling and stains. Serial 9858/9958 (Miura Kimiya)
Maintenance Information: 2015.6.11 Maintained (terminal polishing, cleaning, insulation bush mounting screw replacement. ATT cleaning. Input/output waveform and balance check, sound output check. (Frequency characteristic measurement check)
Accessories: no accessories
Key Specifications: Crossover 1200Hz 8Ω 3-Position Switch with Level Control
The price has been drastically reduced! 2024/4/27 sales price 39,800 yen Center speaker using the same unit as the LS60. The luxurious 3-way specification helps build a theater system. On the exterior, there is a feeling of use, such as small scratches scattered on the top plate. There are small scratches on the exterior. Serial FY00030004240 (Fujisawa Yukishi)
Maintenance information: 2024.4.27 Operation confirmed
Accessories: spike, spike base
Main specifications: 16.5cm double woofer 3-way 4-speaker impedance 6Ω playback frequency band 50-40kHz allowable input 150W dimensions W672 x H217 x D235 mm weight 14.4 kg
※1 bottle only. Maintained! This is a rare blue frame (above) model LX5. The impedance is 8 ohms, and the cross is 500 Hz, so be sure to use a 175 or 375 driver that uses 8 ohms! There are spots, rust spots, and small scratches. (Honda Maki)
Maintenance information: 2021.12.21 Conductivity confirmed 2019.4.4 Maintained (re-fix the internal coil with silicone agent. Remove rust from terminals and mounting screws, clean, and tighten. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: No accessories
Key Specifications: Crossover Frequency: 500 Hz Level Control: 3 Position Switch Input Impedance: 16 ohms 159 x 153 x 120 mm 2.3 kg
The uncompromising construction is excellent, with an aircraft-grade machined aluminum block chassis. I am amazed at its compactness and beauty. I'm only particular about the expressive power of the silent part, and the way the faint sound disappears is as clear as if you take your breath away. It's true that it makes me lament the warmth of human skin. Serial SE0950 (Fujisawa Yukishi)
Maintenance information: 2024.5.12 operation confirmed
Accessories: remote control, instruction manual, power cord
Main Specifications: Input Terminal Unbalance (RCA) 2 Systems/Balance (XLR) 2 Systems/Bypass, Unbalanced (RCA) 1 System Output Terminal Unbalance (RCA) 1 System/Balance (XLR) 1 System Input Impedance/Unbalance 48kΩ/Balance 48kΩ Dimensions W348 x H75 x D191 mm (maximum dimensions) Weight 4.2 kg
*Genuine Oba Shoji product. Although it is a low-end model, the integrated chassis made from a newly selected 6061 aircraft-grade hard aluminum block has an excellent design. The view is good, and the expression of silence gives a sense of comfort. There is a scratch on the front of the exterior. Serial SD1019 (Yonejima Satoshi)
Maintenance information: 2024.5.12 Operation confirmed.
Accessories: instruction manual, power cord
Main Specifications: Continuous Effective Output: 100W x 2 (8Ω) Frequency Band: 5Hz-65kHz, 3dB Dynamic Range: 110dBA Damping Factor: 1000 @1kHz8Ω Gain: 26dB Input Impedance: 40kΩ Input: Balanced (XLR) 1 System Output: 1 System (using CARDAS binding posts) Dimensions: W348 x H75 x D186 (mm) Weight 3.4 kg
Mini plug to stereo standard plug conversion cable It is a model using OFC as a wire rod. (Eiji Tamura)
Maintenance information: 2022.1.5 continuity confirmed
Accessories: original box
※Operation has been confirmed, but since it is cheap, it will be handed over as is. This is a KENWOOD KA series amplifier. It has a compact and clean design, and can be placed horizontally or vertically. The sound quality is as clean as it looks, and it is recommended for those who want to enjoy music in a small space. Serial 61100061 (Sato Wataru)
Maintenance information: 2024.3.26 Operation confirmed
Accessories: No accessories
Main specifications: 3 input lines 12W+12W (8Ω) dimensions W171 x H67 x D207 mm weight 2 kg
All internal deteriorated capacitors and parts have been replaced! Furthermore, a new dust cover has also been created so you can use it comfortably. A masterpiece model of a semi-auto player. The torque and braking power of the motor are excellent, and the stability of operation is impressive. The sound quality, which is delicate and has an excellent sense of resolution, brings out the performance of the cartridge well. There are thin threads on the exterior. Serial 10700499 (Yonejima Satoshi)
Maintenance information: 2024.2.29 Maintained (new dust cover created, motor part removed, shaft and bearing cleaned and lubricated. The tact SW on the operation part and the electrolytic capacitor on the internal board were replaced with a new one. Resolder the board. Remove the area around the arm, clean each part after disassembly, replace the shaft bearing, inspect the internal lead wire, and reassemble. Dust cover hinge reinforcement bracket created. Exterior cleaning, cabinet scratch polishing, rotation speed check, operation test of each part, sound test)
Accessories: instruction manual, screws, EP adapter
Main Specifications: Quartz Lock DD Drive Auto Lift Up Static Balance Type Compatible Cartridge Weight 2 to 12 g Needle Pressure Range 0 to 3 g W490 x H182 x D410 mm 14.5 kg
A speaker stand with a height of about 20 cm. It is recommended for those who want to build a desktop or compact audio system. The exterior has dullness and small scratches (Tamura Eiji)
Accessories: No accessories
Main specifications: top plate 240 x 210 mm thickness 2.3 mm bottom plate 240 x 210 mm thickness 2.8 mm load capacity 12 kg size W210 x H206 x D 240 mm weight 2.2 kg
It is a headphone amplifier with separate power supply with a preamp function. Genuine Naspec. It is compatible with most commercially available headphones, and high sound quality playback is possible even with inner-earphones or authentic stereo headphones. There are small scratches and dullness on the exterior. Serial KRHQ1200069/KRHQP120069 (Yonejima Satoshi)
Maintenance information: 2024.5.16 Operation confirmed
Accessories: power cord, connection cord
Main Specifications: Dynamic Range 110dB SNR 115dB Output Impedance 8Ω Body: W185 x D175 x 53mm 1.0 kg Power Supply Unit: H185 x D150 x H53 mm 1.7 kg
The price has been reduced! 2023/5/15 sales price 19,800 yen A new-concept connected tap equipped with a surge absorber (lightning protection) and noise filter in one package. It has contributed greatly to further improvements in S/N and sharp sound quality that is transparent yet makes you feel dynamic. There are no noticeable scratches on the exterior. Serial 38600KK042 (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Main specifications: W56 x H35 x D233 mm (including connected outlets) 620 g
A ham eraser that can input 1000 VA with 2 inputs. It is mainly effective with front-end devices such as CD players and amplifiers. Delicate and highly transparent sound quality can be obtained due to improved SNR, and clear, high-definition images can be obtained in video systems. PSE standard product. There is dirt on the exterior (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: No accessories
Main specifications: 2 input outlets W130 x H94 x D267 mm (without protrusions) approx. 2.0 kg
The disposal price has been reduced! (Member price not applicable) 2024/4/12 sales price 70,000 yen B&W 805D series speaker stand. Equipped with a spike insulator “T-PROP”. It is a speaker stand with a completely new concept developed with the theme of eliminating speaker stress as much as possible by absorbing and releasing it in a natural way without putting a load on the diamond formation structure. The exterior has scratches, paint peeling, and bumps. (FUJISAWA KOSHI)
Accessories: insulator T-PROP, screws
Main specifications: top plate W227 x D306 mm B&W 805 Diamond, D3 specially designed bottom plate W280 x D360 mm height 500 mm approx. 15 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/23 sales price 99,800 yen, genuine Rin Japan product. A network audio player. It has a simple and modern European design, so you can enjoy a bright sound without getting tired of listening. Not only is it compatible with the LINN system, but it is also equipped with digital output and variable line level output functions not found in the KLIMAX DS and AKURATE DS. There is a thin scratch on the top plate. ※The display is slightly dark, but this is the current situation. Serial 1255165 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 Operation confirmed (Ver. 4.104.518)
Accessories: remote control, power cord
Main specifications: Compatible sampling frequencies 44.1K, 48K, 88.2K, 96K, 176.4K, 192K compatible bits 16-24 bits, output terminals RCA phono (fixed/variable line level output), RCA phono coaxial (digital output) W381 x D360 x H80 mm 4 kg
Maintained. It is a model equipped with the SME 3009R on the LINN LP12. Compatible with everything from lightweight types to heavyweight cartridges such as SPU. Please enjoy the good balance of the large number of sounds unique to analog, the separation of tones, and the profound thickness. There are scratches and dullness on the exterior (Tamura Eiji)
Maintenance information: 2024.5.8 Maintained (power circuit electrolytic capacitor replacement. Arm operation and voice check. (*33 rotations only)
Accessories: No accessories
Main specifications: 3009r/static balance type short type needle pressure 0 to 5g compatible cartridge weight 9.5 to 22 g LP12/W445 x H140 x D356 mm 10.5 kg
The price has been drastically reduced! 2024/5/15 sales price 128,000 yen LINN network audio player with integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1234701 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
Solid brass machined short pin for RCA terminals. Attach it to the input terminal of an audio device to stabilize the input circuit. The exterior has dullness and light threads (Satoshi Yonejima)
Accessories: original box
Main specifications: set of 8, solid machined brass, 24k gold plated, length 28.5 x diameter 12 mm, weight 12.5 g/piece
An affordable Lax interconnect cable with attention to detail, such as each core structure that makes the hot and cold of the 1.0 m RCA cable transmission line the same, and a core wire wrapped in Japanese paper. It is characterized by its moderate thickness and good S/N. (YONEJIMA Satoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: No accessories
※Since the terminal is broken in one place, it is inexpensive. Classic speaker selector. It is a convenient unit for outputting from 1 input system to 4 systems, or conversely, outputting 4 input systems to 1 system. There are scratches and dullness on the exterior. Serial 121-1 G1 (Satoshi Yonejima)
Maintenance information: 2024.5.18 continuity confirmed
Accessories: instruction manual
Main specifications: 1 system/4 system input/output W160 x H65 x D95 mm 530 g
Comes with original box! LUXMAN's classic line selector. It is an easy-to-use and convenient model that outputs from 1 input system to 4 systems, and conversely, outputs from 4 input systems to 1 system. Fairly good condition. Serial 2509-1G2 (Fujisawa Yukishi)
Maintenance information: 2024.5.18 continuity confirmed
Accessories: instruction manual, original box
Main specifications: 1 system, 4 systems input/output W160 x H65 x D95 mm, 530 g
※Since it is cheap, it will be handed over as is. Marantz 10cm full range speaker. There is no habit, and it makes a well-balanced sound from high to low frequencies. It doesn't take up much space, so you can set it up anywhere. The exterior has scratches, dirt, scratches, etc. Also, there is color peeling and partial deformation on saran. Serial MZ01748010115 (Fujisawa Yukishi)
Maintenance information: 2024.2.25 Operation confirmed
Accessories: saran net
Main specifications: 1 way, 1 speaker, bass reflex system, setting free type, rated input 35W, impedance 6Ω, playback frequency 50 Hz to 20 kHz, W230 x H150 x D150 mm
Comes with original box! This is an 8cm full range unit from MarkAudio's ALPair series. It is a self-made unit that is attracting attention because of its technical ability, which has been produced with high accuracy, and has advanced playback capabilities, such as precise and delicate high frequencies. (FUJISAWA KOSHI)
Maintenance information: 2024.5.2 operation confirmed
Accessories: original box
Main Specifications: 8cm full range speaker 4Ω 95-30,000 Hz 85.45dB 10W