Mark Levinson's masterpiece preamp representing the new generation. It is a sound with a high degree of perfection, good texture, and a sense of freshness. There is no lack of power seen in domestic machines, etc., and you can relax and immerse yourself in music with sound quality with intonation typical of high-end aircraft. There is a feeling of use, but there are no noticeable scratches etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 operation confirmed
Accessories: remote control, instruction manual, power cord
Main specifications: Line 7 system high precision discrete attenuator W451 × H74 × D357 mm 9.1 kg
In September 2023, the capacitor was replaced and full maintenance was completed, such as overhauling SW models! A tubular control amplifier representative of Lux. It is soft and produces good mid-range sounds. As you play, the sound becomes more familiar, so I want this amplifier to stay with for a long time. There are black clouds on the exterior (Kobayashi Hitoshi)
Maintenance information: 2023.9.16 Maintained (stepUP transformer socket, tantalum capacitor, block capacitor, electrolytic capacitor, film capacitor, rectifier diode, DIN terminal, power supply SW, headphone volume exchange, RCA terminal polishing, tone VR, lever SW type decomposition cleaning and oxidation and sulfidation prevention grease application, some vacuum tube 12AX7 replacement, cabinet exterior repair/polishing/oil finish, input/output waveform (Check, check the residual noise, check the sound output)
Accessories: none
Main specifications: vacuum tube 12AX7 x 6/12 AU7 x 1 using a tubular control amplifier Input: 2 phono system, line system, 3 system, tape system, 2 system output: 2 systems W476 x H190 x D275 mm 12 kg
The 1.5m pair of RCA cables have bright sound quality, but they don't interfere, and match any source regardless of genre. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.20 Continuity confirmed
Accessories: none
*Since the remote control does not work, it is cheap and is sold as is. Model without phono module. This is a simple, compact Italian premain amplifier. It plays music comfortably with thick sound quality similar to analog audio. It has an elegant appearance that is not irritating. There are no noticeable scratches on the exterior (Kobayashi Hitoshi)
Maintenance information: 2024.4.20 Operation confirmed
Accessories: remote control, instruction manual, original box
Main specifications: output 140W+140W (4Ω), 70W+70W (8Ω) input RCA5 system W210 x H75 x D380 mm 6.3 kg
The 2 shelves are missing and the dowels are missing and cannot be set. A horizontal AV rack designed with heat dissipation and wiring work in mind. Large TVs can be installed. Up to 6 amplifiers, devices, etc. can be stored. You can see the exterior, overall dullness, large abrasions, etc. (Kobayashi Hitoshi)
Accessories: 2 shelves (no missing dowels in the set)
Main specifications: W1202 x H732 x D582 mm load capacity/overall/top plate/shelf board/bottom plate 300/150/50/150 kg mass 83 kg
Jumper wire 18mm (High), 14mm (Low) pair end Y lug specification Caldas tri-wire jumper cable. The model number is unknown. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.20 Continuity confirmed
Accessories: none
Speaker Cable 3.5m Pair Terminal Untreated “M.C.CS 122 HYBRID” Exterior, Dullness, Deterioration, Scratches, etc., and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 continuity confirmed
Accessories: none
Please upgrade to an RCA cable, 1.0 m pair, or Monster Cable standard cable from the original one. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.20 Continuity confirmed
Accessories: none
Speaker cable 5.0 m pair M.C.CS 122 HYBRID is a Vandenhall speaker cable using a parallel multiple stranded wire structure. It is a character that carefully conveys musical expression, and brings depth to the expression of European speakers such as Tannoy, as well as domestic speakers. You can see a feeling of use, such as appearance, writing, dullness, deterioration, scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 continuity confirmed
Accessories: none
Speaker stand for the company's S-55twin. It is a size that is useful for other small and medium speakers. In addition to the exterior and veneer peeling on the side of the bottom, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Accessories: instruction manual
Main specifications: W310 x H498 x D350 mm weight 5.8 kg
Digital cable 1.0 m pure silver conductor uses high-foam polyethylene and Teflon as insulation materials. Heavyweight pin plugs made of machined copper alloy are used. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.21 continuity confirmed
Accessories: original box
Speaker cable, 1.5 meter pair, banana plug specification, is a staple professional cable. Oxygen-free copper (OFC/JIS-H3510) is used as the conductor, and the 4-core structure reduces radiation noise. Polyethylene, which has a low dielectric constant, is used as an insulator to ensure excellent frequency characteristics. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.20 Continuity confirmed
Accessories: none
*Since there is no manufacturer, it will be sold as is. PSE certified product. An isolation regulator that once rectifies AC to DC and creates 60 Hz. Noise removal capability has been greatly improved compared to all models, contributing to leveling up your system. Recommended for front-end devices such as CD players and preamps. Appearance, dullness, small scratches, and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 continuity confirmed
Accessories: power cable
Main specifications: 2 output outlets, output 100V/100W, output frequency 60 Hz, input voltage range 90 to 110 V, W158 x H166 x D365 mm, weight 4.0 kg
This is a 12 dB/oct passive type filter used when playing back SP records on an ELP laser turntable. Removes noise in the high and low frequencies of SP records. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 sound output confirmed
Accessories: instruction manual
Main specifications: cutoff frequency continuously variable low 300 Hz or less, high 2 kHz or more continuously variable W200 x H68 x D170 mm kg
Strong casters are used, making it convenient to move heavy equipment and large speakers. In addition to peeling veneer on the exterior and sides, a feeling of use can be seen such as dullness, scratches, and abrasions (Kobayashi Hitoshi)
Accessories: none
Main specifications: W626 x H126 x D570 mm 14 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/4/19 sales price 178,000 yen Maintained. Rare Fisher tube control amplifier. The 2 phono inputs are attractive. The high range is decent, but the round, rich, and powerful mid-range is unique to FISHER. The sound is light, bright and friendly. *Only CHANNEL A is valid for EQUALIZATION LP and 78 (Murakoshi Yoichi)
Maintenance information: 2024.4.17 maintenance (re-strengthening treatment for all selector knobs (*Please do not remove them as much as possible.) Volume disassembly grease up treatment for BASS, main volume disassembly, cleaning and repair (due to the structure, there are some gang errors and sound leaks when narrowed down to a minimum. (If you are concerned, only RIAA 1 and AUX1 can be adjusted with LEVEL SET on the top surface.) Electrolytic capacitor 1000 μF replacement, vacuum tube socket and RCA jack re-caulking repair. Operation check with AC 100 to 117 V) 2021.5.15 maintained (repair of poor contact with various parts, correction of lever deformation points, replacement of 30/30/10/10 μF defects, vacuum tube socket and RCA jack caulk repair ※ Since the main volume is a special type with a loudness terminal, some gang errors will occur after 12:00. AUX1 and PHONO can be fine-tuned with the LEVEL SET on the top. *Other operation checks have been made (4 vacuum tube shield cases are missing)
Accessories: Service Manual (English)
Main specifications: Vacuum tube 12AX7, 12AT7, 6V4 using PHONO2 system Dimensions W390 x H120 x D210 mm 6.6 kg
Maintained. with cabinet! A power amplifier representing the McKinn Golden Age. It has a rich, gorgeous sound with a punch, and is still a popular model. Although it is a transistor amplifier, it is an amplifier that still has a strong tubular atmosphere. The rich, thick characters reproduce the music on a rich scale. Exterior features include chips and bumps on the cabinet. Serial JCT 4858 (Murakoshi Yoichi)
Maintenance information: 2024.4.3 Maintained (electrolytic capacitors (large capacity capacitors use used products of the same type)), resistors, lamps, etc. have been replaced. Missing screws and rings added. panel paint. Solder correction. Pattern correction. Clean VR and SW connectors. Loosen the screws and tighten them. Bias and offset checks. Output audio check)
Accessories: instruction manual (copy)
Main specifications: 250W+250W (stereo 1/2/4/8Ω) 500W (mono 0.5/1/2/4/8/16Ω) input sensitivity (0.75V/2.5V) switchable W411 x H181 x D368 mm 37.2kg
The price has been reduced. 2024/4/30 sales price 548,000 yen Denon premain amplifier. They generously introduced special custom capacitors, and I can only say that 4 years of development were spent, so it's pretty good. The sound is well grained, and the sound comes out comfortably over the entire area. The exterior is good with no conspicuous scratches. Serial BMM15220700235 (Hiura Katsuji)
Maintenance information: 2024.4.29 sound output confirmed
Accessories: instruction manual, remote control, power cable, original box
Main specifications: 50W+50W (8Ω) 100W+100W (4Ω) PHONO (MM/MC) balance input x 1, unbalanced input x 5, PHONO (MM) input x 1, PHONO (MC) input x 1, EXT. PRE×1 analog audio output terminal unbalanced output (RECORDER) ×1 frequency characteristics 5 Hz to 100 kHz W434 × H181 × D504 mm 29.5 kg
A classic MC boost transformer. With 2 input systems, impedance can be switched to 3.40 ohms, and comes with a PASS line, you can freely enjoy various cartridges and tone arms (Takasaki Atsushi)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
Balance cable 1.0m pair Glen optimized copper+polymer coating features a rich three-dimensional, high-contrast expression. The exterior is dull and has a feeling of use (Hiura Katsuji)
Maintenance information: 2024.4.20 continuity confirmed
Accessories: none
Speaker stand for YAMAHA NS-05 and NS-1 Perfect for other companies' small speakers (Takasaki Atsushi)
Accessories: none
Main Specifications: Speaker Stand External Dimensions W250 ✕ H385 ✕ D330 mm Weight 4.0 kg
RCA cable, 1.0 m pair, antistatic, transparent polymer, compression, twisted, 8N copper conductor, SVPE insulation, draws a clean and clear sound image. There is a slight feeling of use (Takasaki Atsushi)
Maintenance information: 2024.4.21 continuity confirmed
Accessories: original box, seal
Balance cable 1.0m pair Glen optimized copper+polymer coating features a rich three-dimensional, high-contrast expression. The exterior is dull and has a feeling of use (Hiura Katsuji)
Maintenance information: 2024.4.20 continuity confirmed
Accessories: none
RCA cable, 1.5 m pair, antistatic, transparent polymer coating, compression stranded, 8N copper conductor, SVPE insulation, draws a clean and clear sound image. There is a slight feeling of use (Takasaki Atsushi)
Maintenance information: 2024.4.21 continuity confirmed
Accessories: original box, seal
Power cable 2.0m POWER MAX series high CP cable PCOCC-A conductor is used with a 3.5 scare copper foil shield, tourmaline sheath, carbon CSF tube, etc. and are built without compromise (Hiura Katsuji)
Maintenance information: 2024.4.30 continuity confirmed
Accessories: none
Maintained! Single stereo power amplifier using 2A3 output tubes. You can enjoy the aftertaste of sound and air unique to vacuum tubes. It expresses vocals and string music in a sweet and glamorous manner. This is a well-built car at an affordable price. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.29 maintenance completed (power supply capacitor replacement, RCA jack replacement, cord clamp added to keep unused wire away from heat source, fixed solder defects, vacuum tube pin cleaning, bias check ham balance adjustment, output approx. 4.5 W (current load set to 8 Ω), interior and exterior cleaning)
Accessories: power cable
Main specifications: rated output 3.5W+3.5W vacuum tube 2A3 x 2 6H8C x 2 5U4G x 1 W360 x D210 x H190 mm 16 kg
*Currently sold. There is a gap in the right VOL, which is the current situation. It's an inexpensive yet powerful amplifier. The model, which combines stable operation and abundant power, has a good sense of dynamism in the sound, and it feels like it comes to the fore. The input is equipped with an unbalanced RCA pin and a balanced TRS phone. A feeling of use can be seen on the exterior, marks, dullness, small scratches, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.26 Operation confirmed
Accessories: power cable
Main specifications: 45W+45W (8Ω) bridge output 150W (8Ω) W480 × H99 × D260 mm 6.8 kg
*Currently sold. It's an inexpensive yet powerful amplifier. The model, which combines stable operation and abundant power, has a good sense of dynamism in the sound, and it feels like it comes to the fore. The input is equipped with an unbalanced RCA pin and a balanced TRS phone. You can see a feeling of use on the exterior, marks, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.26 Operation confirmed
Accessories: power cable
Main specifications: 45W+45W (8Ω) bridge output 150W (8Ω) W480 × H99 × D260 mm 6.8 kg
Stylish audio-technica cartridges. It's a sharp, nice sound. The color has faded and there is dullness (Kanai Hidetsugu)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: none
Main specifications: VM type needle pressure 1-2 g dead weight 17 g
ELAC's classic MM cartridges. The tone spun out of the gold body is a firm tone, and you can also enjoy the subtle high frequency and warm MM-like thickness. There is a scuff on the side (Mizushima Itsuro)
Maintenance information: 2024.4.22 operation confirmed
Accessories: none
Main specifications: mm type output 5.5 mV playback frequency band 10 Hz to 25,000 Hz needle pressure 0.75 to 1.5 g dead weight 6.5 g
Pioneer rare cartridges. It uses an aluminum light alloy pipe cantilever, and the impression is that the range is quite wide for its age. The exterior is dull and has a feeling of use (Kanai Hidetsugu)
Maintenance information: 2024.4.28 sound output confirmed
Accessories: none
Main specifications: mm type output voltage 3.5 mV optimal needle pressure 2.2 g load resistance 30 to 100 kΩ playback frequency band 15 to 25,000 Hz needle tip 0.5 mil joint type diamond dead weight 5.7 g
MM type cartridge developed based on the DL-107. The magnet has a 1-point support structure using a disc-shaped magnet. A special elliptical needle is used at the tip of the needle, and it makes a smooth sound with excellent high frequency characteristics. There is corrosion on the cantilever serial 1820 (Kanai Hidetsugu)
Maintenance information: 2024.4.28 sound output confirmed
Accessories: needle cover
Main specifications: mm type output voltage 3 mV applicable needle pressure 1.5 to 2.1 g (1.8 g suitable) special elliptical needle frequency characteristics: 20 Hz to 50 kHz dead weight approx. 7.5 g
2M series RED. The good sound and fluttering energy typical of an orthophone are attractive. The degree is generally good (Kanai Hidetsugu)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: needle cover
Main specifications: MM type 5.5 mV 20 to 22,000 Hz 47 ohms suitable needle pressure 1.8 g dead weight 7.2 g
2M series RED. The good sound and fluttering energy typical of an orthophone are attractive. The degree is generally good (Kanai Hidetsugu)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: needle cover
Main specifications: MM type 5.5 mV 20 to 22,000 Hz 47 ohms suitable needle pressure 1.8 g dead weight 7.2 g
A new-generation cartridge with the perfect setting for cord vinyl and powerful output. Compatible with hard environments such as DJ play, scratches, and vibrations (Kanai Hidetsugu)
Maintenance information: 2024.4.29 sound output confirmed
Accessories: original box, instruction manual (English), needle cover
Main specifications: MM 10mV 20 to 18,000 Hz, proper needle pressure, 4 g dead weight, 18.5 g
※6 month warranty. A PIONEER tall boy speaker with clean sound quality and good balance. It is a model developed for AV use, but it also sounds in a wide range as pure audio regardless of genre. It is a model with high cost performance even as an introductory machine. There are large tape marks on the exterior and back, and a feeling of use such as dullness and bruises can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.4.26 Operation confirmed
Accessories: saran net, jumper (general purpose)
Main specifications: woofer 16 cm cone type x 2 mid tweeter coaxial 13 cm cone type, 3 cm dome type ribbon type super tweeter 6Ω 89dB W274 x H1075 x D366 mm 37 kg
The price has been reduced. 2024/4/29 sales price 9,000 yen. ※Unused item. *Set of 3. A gradation cast iron insulator that firmly supports equipment with heavy construction. The excellent damping properties of cast iron and the vibration blocking effect of pinpoint support make the mid to low frequencies clear, and accurate sound images can be obtained (Hiura Katsuji)
Accessories: original box
Main specifications: diameter 60 x height 45 mm weight 800 g/piece plate diameter 35 x height 5 mm weight 40 g/piece
Pioneer perforated headshell Carbon fiber molding The shell is lightweight, has just the right length on the finger, and is easy to use. The exterior has a feeling of use such as dullness (Kanai Hidetsugu)
Maintenance information: 2024.4.28 sound output confirmed
Accessories: none
Main specifications: dead weight 8.7g
The price has been reduced. 2024/4/29 sales price 110,000 yen The 3 channel 5 units are nicely put together in one package. In addition to the fact that a rich sound field can be simply played back via Bluetooth, etc., it is a product with an emphasis on functionality that can also be enjoyed with analog. Recommended for studio users. Other than the exterior and stains on the top plate, it's fine (Kobayashi Hitoshi)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: remote control, power cord
Main specifications: 33mm pure pulp cone woofer x 2, 25mm aluminum dome tweeter x 2, 100mm pure pulp cone center midrange x 1 input HDMI (ARC), 3.5mmAUX, RCA Phono (MM), Ethernet/WiFi Bluetooth playback frequency characteristics 45 Hz to 25 kHz (-6 dB) W790 x H216 x D287 mm 15.9 kg
An attractive audio analog CD player with a compact yet sweet, and rich sense of scale. The vocals are also rich in expression, and you can enjoy a relaxed, adult sound. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.28 Operation confirmed
Accessories: remote control, original box
Main specifications: 1 analog output system/1 digital output system W210 x H75 x D370 mm 4.9 kg
A digital premain with a neutral, clear tone and spatial expressiveness. While saving power with a power consumption of 42W, it demonstrates outstanding speaker driving power, making it ideal for listening at low volume levels. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.28 Operation confirmed
Accessories: spike, spike holder, 2 spare knobs, instruction manual, power cord
Main specifications: rated output 60 W x 2 (8 Ω) S/N ratio 100 dB frequency characteristics 5 Hz to 100,000 Hz input sensitivity 500 mV/10 kΩ input RCA analog 3 systems/1 front mini stereo jack system W420 x H98 x D243 mm 6.0 kg
German MM/MC compatible phono equalizer. The speed of sound is outstanding. The sound quality is straight without turbidity, and the volume and power of the bass are excellent, and the rhythm band can be heard richly. It's an excellent product that also allows you to get good MC gain. There is an MM/MC changeover switch on the bottom, making it very easy to use. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual
Main specifications: 60dB (MC) 40dB (MM) input impedance 800Ω/MC, 47kΩ/mm W50 ✕ H30 ✕ D74mm 0.2 kg
※Although it was an unopened item, I opened it for a photo shoot. Since it is cheap, it will be handed over as is. Comes with a remote control. Slim AM/FM digital tuner. The reception frequency range is wide and you can also listen to wide FM (Kobayashi Hitoshi)
Maintenance information: 2024.4.20 Operation confirmed
Accessories: remote control, instruction manual, power cord, connection cord, antenna, original box
Main specifications: AM/FM compatible digital tuner with auto preset memory [FM] reception frequency range 76.0 to 108.0 MHz frequency characteristics 20 Hz to 15 kHz SNR 70 dB, mono 75 dB [AM] reception frequency range 522 to 1,629 kHz dimensions W434 x H73 x D284 mm weight 3.6 kg
Audio-Technica connectable cartridge capsule. One can be stored while the headshell is attached. The exterior has scuffs, dullness, and a feeling of use (Katsuji Hiura)
Accessories: none
Main specifications: W51×H85×D51mm
1 set of 4 Y rugs It is a screw-tightened metal Y lug terminal that can be easily fixed and is compatible with various core wire diameters and terminal diameters. There is dullness (Mizushima Itsuro)
Accessories: none
Main specifications: core wire strand diameter 1.5 to 4.0 mm, terminal diameter up to 6.0 mm
Amplifier/Speaker Selector It can be used to switch between 3 amplifiers and 2 sets of speakers (or 3 sets of speakers and 2 amplifiers). High quality, which pays attention to the quality of domestic cables, is selling well. There is a slight feeling of use (Takasaki Atsushi)
Maintenance information: 2024.4.28 continuity confirmed
Accessories: none
Main specifications: 24K gold-plated speaker terminal compatible with both stripped wire and banana plug input 3 (L/R) /output 2 (L/R) or input 2 (L/R) /output 3 (L/R) dimensions H55 x W200 x D175 mm, weight approx. 1.4 kg
It is a Schumann resonance wave (7.83 Hz) generator that increases the S/N ratio by canceling electromagnetic waves etc. generated from the entire audio equipment. To use it, power the included AC adapter from an electrical outlet and place the main unit as high as possible in the room (1 m 50 cm or more). There is no noticeable damage to the exterior (Kobayashi Hitoshi)
Maintenance information: 2024.4.20 Operation confirmed (power can be turned on, effect not measured)
Accessories: power cable
Main specifications: Schumann resonance wave (7.83 Hz) generator input voltage 12V W140 × D170 × H50 mm 220 g