*Currently sold. Yamaha superwoofer equipped with a 20 cm x 2 double woofer. Equipped with active servo technology and a 150W high-power amplifier, it plays bass that is small yet full of volume. There is dirt, dirt and dullness on the exterior, and some floating on the bottom. Serial Z117079QS (Tamura Eiji)
Maintenance information: 2024.3.3 sweep test is good
Accessories: No accessories
Main specifications: used unit 20 cm cone type x 2 rated output 150 W (5 ohms) playback frequency band 20 Hz to 160 Hz high cut filter 40 Hz to 140 Hz, continuously variable W235 x H602 x D463 mm 20 kg
The 1.8 m PSE standard MK2 power cable is not only flexible and easy to use, but the sound quality has also been brushed up with fewer habits. You can get clear, sharp sound. There is a frayed sheath (Tamura Eiji)
Maintenance information: 2024.4.24 continuity confirmed
Accessories: none
The 1.8 m PSE standard MK2 power cable is not only flexible and easy to use, but the sound quality has also been brushed up with fewer habits. You can get clear, sharp sound. There is a frayed sheath (Tamura Eiji)
Maintenance information: 2024.4.24 continuity confirmed
Accessories: none
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
※Since it is inexpensive, it will be handed over as is. Tamban 10cm full range unit. An ultra-thin PP diaphragm with reinforced ribs is used. The sound is clear and crisp. A 6-8 liter bass reflex box is recommended (Tamura Eiji)
Maintenance information: 2023.10.1 sweep check OK
Accessories: none
Main Specifications: Rubber Edge Impedance 4 Ohms Sound Pressure Level 87 dB Frequency Band 63 to 17,000 Hz Maximum Input 40 W Baffle Aperture Diameter 94 mm Weight 380 g
* Since there are difficulties with the attachment part on both sides, it is inexpensive. Line matching transformer sold primary: 600 ohms, output 10 dBm, frequency range, 50 to 10 kHz, W44 x H65 mm, 0.25 kg/piece, the head of the mounting bolt on one side is flying off, and there is distortion in the screw hole on the other side (Kojima Yosuke)
Accessories: none
Line matching transformer sold 1 piece Primary: 600 Ω - CT Secondary: 600 ohms Output 10 dBm Frequency Range 50 to 10 kHz W44 x H65 mm 0.25 kg/piece There are bumps and paint peeling in places (Yosuke Kojima)
Accessories: none
Line matching transformer sold 1 piece Primary: 600 Ω Secondary: 600 Ω Winding Ratio 1:1 Output 10 dBm Frequency Range 50 to 10 kHz W34 x H42 x D22 mm Approx. 0.1 kg (Yosuke Kojima)
Accessories: none
Wood cabinet for TD-124 of unknown manufacturer. It can be equipped with an SME long arm. The exterior has scratches, threads, chips, etc. (Tamura Eiji)
Accessories: no accessories
Main Specifications: W597 ✕ H160 ✕ D445mm Weight 3.9 kg
SAEC long-selling model with a 0.6 m digital cable. 6N ultra-high purity copper with excellent transmission characteristics is used as the conductor material, and transmission loss is reduced with accurate impedance matching (Tamura Eiji)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
The price has been reduced! 2024/3/6 sales price 25,000 yen speaker cable 1.0 m pair banana on both ends uses the company's highest-grade cable material. Recommended for those who want to improve the tightness of the low frequencies. On the exterior, there is a part where the rubber ring on the terminal is off. ※The cable is stiff, so please be careful when routing (Tamura Eiji)
Maintenance information: 2024.3.6 continuity confirmed
Accessories: No accessories
Set of 4 spike bases A spike bass for audio created with an emphasis on strength and non-resonance. High-strength 2000 series alloy (non-magnesium) is used. Sound strength, sense of positioning, etc. can be improved. There is oxidation on the exterior (Tamura Eiji)
Accessories: none
Set of 4 spike bases A spike bass for audio created with an emphasis on strength and non-resonance. High-strength 2000 series alloy (non-magnesium) is used. Sound strength, sense of positioning, etc. can be improved. There is oxidation on the exterior (Tamura Eiji)
Accessories: none
The price has been drastically reduced! 2024/4/24 sales price 118,000 yen*Saran net is out of stock, scratches, etc.
It's cheap because it's not in good condition. ATC small bookshelf. The thick and powerful mid-low range is attractive. If you pair it with a good amplifier that has torque, you can enjoy it on a scale that greatly exceeds its size. There are scratches on the exterior. Serial 0819/0820 (Tamura Eiji)
Maintenance information: 2024.4.24 sweep test good
Accessories: No accessories
Main specifications: 2 way 2 speakers sealed impedance 8 ohms size W211 x H380 x D250 mm weight 11.4 kg
※It has a cigarette smell, so it's cheap. Currently sold. 115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are scratches on the exterior. Serial 2172380XCK00186 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
※It has a cigarette smell, so it's cheap. Currently sold. 115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are scratches on the exterior. Serial 217380XCK00185 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
※It has a cigarette smell, so it's cheap. Currently sold. 115V specification A German stereo power amplifier with resolution and expressiveness not typical of commercial use. It is proud of its exhilarating sound and outstanding driving power that comes out quickly. The exterior has scratches and paint bald spots. Serial 2172380UGD01107 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 85W+85W (8Ω) 150W+150W (4Ω) W483 x H88 x D270 mm 11.5 kg
Y lug plug set of 4 have mirror-polished terminal contact parts made of leadless brass material with excellent conductivity, and rhodium plating treatment has been applied to the surface to further improve conductivity and durability (Tamura Eiji)
Accessories: original box, instruction manual
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
Disposal prices have been reduced! (Member discounts are not applicable) 2022/5/18 sales price 2,000 yen When used between an S-terminal AV noise filter device and a display, unnecessary noise is removed without deteriorating the amount of information or high frequency characteristics of the video signal at all, and the video signal is organized. The exterior is dull and dirty, and there are floating marks on the label. (TAMURA Eiji)
Maintenance Information: 2022.5.18 Continuity Confirmed
Accessories: There are no accessories
Quadra 180mm pole set of 4 The neck is curved rather than straight. There is oxidation on the exterior (Tamura Eiji)
Accessories: head part of the head
Unused item! Power transformer primary: 90-100-110V secondary: 6.3V/3A x 2, 400-325-0-325-400V/230mA, 5V/3A W122 x H150 x D102 mm 5.4 kg (actual measurement) (Kojima Yosuke)
Accessories: none
Maintained by Denon! This is DENON's mid-range model, and is a staple machine with an excellent sense of stability, with firm bass and delicate high frequencies. In addition to the bass energy from conventional models, you can enjoy well-balanced sound that takes into account the high mid to high frequencies with a high sense of transparency. There are small scratches on the exterior. Serial 8061507480 (Tamura Eiji)
Maintenance information: 2024.4.17 manufacturer maintained (Rch amplifier circuit, transistor and resistor replacement. Amplifier board soldering correction (both channels). (Idle current adjustment and operation inspection carried out.)
Accessories: instruction manual, power cable, original box
Main specifications: rated output 80W+80W (8Ω) PHONO1 system (MM/MC switching) dimensions W434 x H181 x D480 mm weight 24.0 kg
The price has been reduced! 2024/4/18 sales price 59,800 yen ※Since it is a commercial device, it will be handed over as is. It's a very powerful sound unique to professional machines, and it pushes the sound forward and forward. Recommended for jazz and rock fans with large woofers. The exterior has scratches, bumps, etc. Serial JP01026 (Tamura Eiji)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: none
Main specifications: 240W+240W (8Ω) 480W (16Ω MONO) with peak output meter W480 × D413 × H183 mm 20.5 kg
※It is inexpensive because the condition is poor due to scratches, threads, and partial sheath deformation. Off sale power cable, 1.0 m, has an unprocessed end that combines performance and safety at an astonishing level. There are dirt and scratches on the exterior (Tamura Eiji)
Accessories: No accessories
* It seems to be an output transformer from the specifications; sold 1 piece, primary: 10 kΩ, secondary: 600 ohms, W76 x H71 x D43 mm, 0.6 kg (actual measurement, not including protrusions), there is paint peeling in places (Kojima Yosuke)
Accessories: none
Output transformer sold 1 piece Primary: 14 kPPΩ Secondary: 600 Ω WW76 × H71 × D43 mm 0.6 kg (actual measurement, protrusions not included) There are paint peeling and seal marks in places (Kojima Yosuke)
Accessories: none
A speaker stand with a height of about 20 cm. It is recommended for those who want to build a desktop or compact audio system. The exterior has dullness and small scratches (Tamura Eiji)
Accessories: No accessories
Main specifications: top plate 240 x 210 mm thickness 2.3 mm bottom plate 240 x 210 mm thickness 2.8 mm load capacity 12 kg size W210 x H206 x D 240 mm weight 2.2 kg
The price has been reduced! 2024/4/25 sales price 998,000 yen SME's current record player has arrived! Similar to the “Model 12A,” it uses a new-generation advanced electronic speed control unit, and detailed speed control is possible. The arm is equipped with the “M2-9R,” which can be said to be the successor to the “3009,” and is compatible with a wide range of cartridges. Please enjoy the one that represents this class. Serial 0075 (Tamura Eiji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: instruction manual (English), belt, power cable, connection cable, original box, IFC weight, stabilizer, head shell
Main specifications: main unit: W420 x H90 x D320 mm Power supply unit: W220 x H85 x D200 mm Weight: 11.4 kg including power supply
The price has been reduced! 2024/4/25 sales price 1,280,000 yen An analog player produced by SME, a prestigious tonearm company. Vibrations are suppressed with a unique isolation system and high-quality aluminum, and stable sound reproduction is achieved with an elaborate set of parts unique to SME. The arm is equipped with a specially designed 309, so you can enjoy rich and stable analog sound. Serial 0105 (Tamura Eiji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: instruction manual, connection cable, power cable, stabilizer, tool, original box
Main specifications: Compatible speed: 33, 45, 78 rpm Main unit: W370 x H170 x D350 mm Power supply unit: W170 x H68 x D305 mm Weight: 25.9 kg
The price has been reduced! 2024/3/22 sales price 29,800 yen The tuning hole uniquely arranged on Oyaide's turntable plate thoroughly eliminates unnecessary vibrations that disrupt the record board's trace, and can also be used in combination with a stabilizer to correct the warpage of the record board and expect an appropriate trace. There are small scratches and dullness on the exterior (Tamura Eiji)
Accessories: instruction manual, original box
Main specifications: dimensions: 294 mm, thickest part: 5 mm, 670 g
※Since it is cheap, it will be handed over as is. 1 bottle only 25cm full range speaker made by RCA in the USA. The Alnico magnet responds well and the sound is easy to remove. There are repair marks on the edge (Tamura Eiji)
Maintenance information: 2024.3.22 sweep test good
Accessories: No accessories
Key Specifications: Unit Diameter 25cm 8Ω Fixed Edge
Balance cable is a standard 1.5m pair Accuphase balance cable. It is a natural sound that removes disguise to enhance the characteristics of amplifiers and players. As for the exterior, there is room odor on the sheath (Tamura Eiji)
Maintenance information: 2024.3.14 continuity confirmed
Accessories: none
The price has been reduced! 2024/4/25 sales price 498,000 yen KLIMAX DSM/1 is a model created through a DSM/2 upgrade service. It is a car where you can fully enjoy the “KLIMAX” quality while keeping the simple structure typical of LINN. There are no noticeable scratches on the exterior. Serial 1427895 (Tamura Eiji)
Maintenance information: 2024.4.25 Maintained (removal of residual parts damaged in the output jack. RCA jack L R both replaced (made by WBT). Ver (4.104.518))
Accessories: power cable
Main Specifications: Support Files: FLAC, WAV, ALAC, AIFF, AAC, MP3, WMA Compatible Sampling Frequency: 44.1 to 192 kHz Compatible Bits: 16-24 Bits W381 x H80 x D280 mm Weight 2.7 kg
Maintained. Battery-powered MC head amplifier. The modular type allows you to enjoy analog playback like the company's ML series. It has the sharpness and dynamic sound unique to being battery-powered, and the combination with the old SPU is particularly exquisite. There are scratches and scratches on the exterior. Serial 1232 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (there is a liquid leak mark on the battery holder. (It was cleaned and repaired because it was not available.)
Accessories: No accessories
Main specifications: 8 mV (maximum), output terminal with battery checker, 250 mV (maximum), frequency band 20 to 50,000 Hz, W220xH45xD100mm, 0.7 kg
Output transformer sold 1 piece Primary: 5 kΩ Secondary: 6 Ω/600 Ω NFB W68 × H91 × D72 mm 1.28 kg (actual measurement, not including protrusions). From specifications, it seems to be a line output transformer. There are rust spots, scratches, and paint peeling in places (Kojima Yosuke)
Accessories: none
The price has been drastically reduced! 2024/4/17 sales price 69,800 yen ※It is cheap because it has a tobacco smell. Hi-Fi Man's planar drive headphones have a high resolution, and the low frequencies are clear and easy to listen to. The sound balance is flat and the high cushioning is also impressive. The exterior smells like tobacco and there are creases on the cable (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box, connection cable
Main specifications: planar drive impedance 50 ohms sound pressure sensitivity 83.5 dB playback frequency band 8 Hz to 65 kHz 505 g
A headphone amplifier compatible with headphones with various impedances, from foreign-made headphones with high impedance to headphones made in Japan with low impedance. The high-frequency sound is very beautiful, and the sound is transparent, and you can feel a sense of realism. Equipped with a speaker terminal, it can be used as a simple pre-main amplifier. The exterior is dull. Serial HD53R062.5045005 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: power cable, instruction manual
Main specifications: 1 input RCA, 1 XLR system, 1 output speaker system, 2 headphone systems W217 x H51 x D391 mm 2.6 kg
Light and compact, stylish headphones from JVC. The sound has excellent sound insulation and is comfortable to listen to (Tamura Eiji)
Maintenance information: 2024.3.15 sweep check OK
Accessories: case
Main specifications: dynamic type 12 to 24,000 Hz 32 ohms 103 dB 66 g
RCA cable 1.0 m pair The copper/aluminum/brass hybrid configuration, which is also a characteristic of the company, has a high resolution and is an exciting sound that comes out quickly. There is some discoloration on the sheath (Tamura Eiji)
Maintenance information: 2024.3.27 continuity confirmed
Accessories: none
It is a USB-connected bus-powered D/D converter that uses the C-Media “CM6642” as the digital audio control IC and is compatible with high-resolution sound sources (maximum 24 bit/192 kHz) (Tamura Eiji)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, original box
Main specifications: digital input: USB TypeB terminal USB 1.1/2.0 compatible, USBAudioClass 1.0/2.0 compatible digital output: coaxial digital audio output (COAXIAL) optical digital audio input (square) compatible format: PCM maximum 24 bit 192 kHz W40 x H25 x 81 mm 90 g
The disposal price has been reduced. Member prices are not applicable. 2023/12/7 sales price 25,000 yen*Exclusive earth cable is out of stock. Since the cable is soldered to the connection part, it is inexpensive. A sandwich structure with an electromagnetic wave absorbing sheet sandwiched between two aluminum panels. Both sides of the aluminum panel are dark gray and light gray and can be reversed for use. There are line scratches and tape marks on the exterior (Tamura Eiji)
Main specifications: W470 x H7 x D420 mm weight 3.4 kg
The disposal price has been reduced. Member prices are not applicable. 2023/12/7 sales price 25,000 yen*Exclusive earth cable is out of stock. Since the cable is soldered to the connection part, it is inexpensive. A sandwich structure with an electromagnetic wave absorbing sheet sandwiched between two aluminum panels. Both sides of the aluminum panel are dark gray and light gray and can be reversed for use. There are line scratches and tape marks on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: W470 x H7 x D420 mm weight 3.4 kg
This is an MC-type cartridge from Entre. The sound is slightly stiff and sharp, and the sound quality is sharp. The outline and texture of the low frequencies are also firm. There are no particular bends. Serial 39354 (Tamura Eiji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: none
Main specifications: MC type output 0.5 mV needle pressure 1.7 g to 2.3 g (appropriate 2.0 g) impedance 6.3 ohms dead weight 5.9 g
*Fully auto player with built-in phono equalizer from Denon currently sold. It is recommended for those who want to enjoy records casually without worrying about the location or for beginners. There are scratches on the exterior. Serial 0063373998 (Tamura Eiji)
Maintenance information: 2023.12.8 operation confirmed
Accessories: none
Main Specifications: Fully Auto Player Belt Drive Appropriate Needle Pressure 3.5g W360 ✕ H ✕ D370mm Weight 2.9 kg