The price has been reduced. 2024/1/5 sales price 400 yen. ※1 bottle only. 3 cm unit with unknown details. Since the size and condenser is attached to the plus side, it seems to be a tweeter. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2022.11.15 Operation confirmed
Accessories: none
Main specifications: actual impedance measurement 3 ohms 3 cm
SAEC long-selling model with a 0.6 m digital cable. 6N ultra-high purity copper with excellent transmission characteristics is used as the conductor material, and transmission loss is reduced with accurate impedance matching (Tamura Eiji)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
Disposal prices have been reduced! (Member discounts are not applicable) 2023/2/5 sales price 10,000 yen ※1 bottle only. DynAudio's classic 17cm cone woofer. It has resolution and is recommended for bookshelves, etc. The urethane on the back magnet side has not deteriorated (Tamura Eiji)
Maintenance information: 2023.2.5 good sweep test
Accessories: There are no accessories
Main specifications: 17 cm cone type impedance 4 ohms diameter 176 mm depth 66.5 mm
Variable Resistor Attenuator Bridge T Type 21 Steps Maximum Attenuation 50 dB Impedance 600 Ohms W45 x 64 mm 140 g with Volume Knob (Kojima Yosuke)
Accessories: volume knob (attached to the main unit)
※Since it is inexpensive, it will be handed over as is. Tamban 10cm full range unit. An ultra-thin PP diaphragm with reinforced ribs is used. The sound is clear and crisp. A 6-8 liter bass reflex box is recommended (Tamura Eiji)
Maintenance information: 2023.10.1 sweep check OK
Accessories: none
Main Specifications: Rubber Edge Impedance 4 Ohms Sound Pressure Level 87 dB Frequency Band 63 to 17,000 Hz Maximum Input 40 W Baffle Aperture Diameter 94 mm Weight 380 g
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
※Since it is cheap, it will be handed over as is. Marantz 10cm full range speaker. There is no habit, and it makes a well-balanced sound from high to low frequencies. It doesn't take up much space, so you can set it up anywhere. The exterior has scratches, dirt, scratches, etc. Also, there is color peeling and partial deformation on saran. Serial MZ01748010115 (Fujisawa Yukishi)
Maintenance information: 2024.2.25 Operation confirmed
Accessories: saran net
Main specifications: 1 way, 1 speaker, bass reflex system, setting free type, rated input 35W, impedance 6Ω, playback frequency 50 Hz to 20 kHz, W230 x H150 x D150 mm
※The unit has noticeable mold spots, so it is inexpensive. It is a model equipped with a sound diffuser that can adjust directivity characteristics to the listening position while maintaining the quality and ease of use of the 101 series. On the exterior, there are scratches and mold on the unit. Serial 006855/006856 (Tamura Eiji)
Maintenance information: 2024.3.3 sweep check OK
Accessories: saran net, diffuser
Main specifications: 11.5cm full range anti-magnetic type maximum output 150W impedance 6Ω dimensions W232 × H154 × D162 mm weight 2.2 kg
※This item is currently sold. Onkyo enabled speaker. It is a design that makes it possible to construct a Dolby Atmos sound field using sound reflection from the ceiling. Accessories such as brackets and cables are missing (Sasaki Shota)
Maintenance Information: 2023.12.11 Sweep Test Good
Accessories: none
Main specifications: sealed impedance 6 ohms, playback frequency band 90 Hz to 20 kHz, W120 x H155 x D153 mm, 1.2 kg
Disposal prices have been reduced! (Member discounts are not applicable) 2023/7/31 Sales price 15,000 yen*Currently sold. It is a 2.1 channel speaker system that perfectly matches Bose's unique compact, high-performance speaker technology with bass reproduction technology. You can easily enjoy simple 2.1 channels. As for the exterior, there are cracks in the woofer cabinet, overall dullness, and small scratches. Serial 990701 (Yonejima Satoshi)
Maintenance information: 2023.7.31 Operation confirmed
Accessories: no accessories
Main Specifications: Rated Input 100W Impedance 6Ω Satellite Speaker 6.0 cm Driver x 2, Antimagnetic Type, W78 x H157 x D104 mm, 1.1 kg, Subwoofer, 13 cm, 2 Drivers, W485 x H358 x D192 mm, 9.1 kg
*Currently sold. The classic 101 mm small speaker. The sound, which has been compiled in one small full-range shot, makes all kinds of popular music sound cheerfully. The exterior has scratches, threads, and dullness. There is also a dent in the saran net. Serial 108023/089692 (Tamura Eiji)
Maintenance information: 2024.3.3 sweep check OK
Accessories: saran net
Main specifications: 1 way 1 speaker impedance 6 ohms maximum input 150 W output sound pressure level 86 db W232 x H154 x D172 mm 2 kg
The price has been drastically reduced. 2023/12/11 sales price 15,000 yen*There is no problem with operation, but since it is cheap, it is being delivered as is. Center speaker for the company's STAGE series. Please help build a theater system (Daiki Goto)
Maintenance information: 2023.12.11 operation confirmed
Accessories: instruction manual
Main specifications: 2-way dual 133mm woofer, 25mm aluminum treble unit impedance 6Ω efficiency 88dB W469 x H190 x D220 mm weight 7.95 kg
This is an MC-type cartridge from Entre. The sound is slightly stiff and sharp, and the sound quality is sharp. The outline and texture of the low frequencies are also firm. There are no particular bends. Serial 39354 (Tamura Eiji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: none
Main specifications: MC type output 0.5 mV needle pressure 1.7 g to 2.3 g (appropriate 2.0 g) impedance 6.3 ohms dead weight 5.9 g
※There is no problem with operation, but it is currently sold because it is cheap. A small 2-way speaker made by ONKYO. The bass reflex system allows you to enjoy low frequency playback with a compact appearance yet a sense of volume. There is slight stickiness on the front (Daiki Goto)
Maintenance information: 2024.4.10 operation confirmed
Accessories: none
Main specifications: 2-way bass reflex type rated impedance 4 ohms maximum input 120 W rated sensitivity level 82 dB W156 x H249 x D221 mm 4.1 kg
High output MC cartridge for mono LPs only. Plays deep sound that was not produced with stereo cartridges. It has the vividness unique to Technica, but the three-dimensional effect and intensity are an appeal unique to mono (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: needle cover
Main specifications: high output MC type output 1.2 mV needle pressure 2.0 g impedance 40 ohms dead weight 6.8 g
The price has been reduced. 2023/6/1 sales price 25,000 yen A fully discrete genuine analog amplifier designed with an amplifier using a total of 10 pairs of carefully selected transistors without using an operational amplifier. It's lightweight, compact, and useful for portable applications. The exterior has scratches and scratches on the main body (Mizusaki Ryo)
Maintenance Information: 2023.6.1 Sound output confirmed
Accessories: AC adapter, USB cable, silicone band, carrying case, original box
Main specifications: input 3.5mm mini terminal output 3.5mm mini terminal input impedance 30kΩ output 200mW (32Ω) 100mW (50Ω) 50mW (300Ω) 15mW (600Ω) W97 x D46 x H19 mm (including volume knob) weight approx. 117 g
This standard cartridge is particularly famous in the company's MC series. It has good stretch in the high range and a texture that feels good against the skin, has thickness and density in the mid-range, and it is a tone that makes you feel a sense of temperature (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: MC type output voltage 0.09 mV needle pressure 1.7 g playback frequency band 20 to 20,000 Hz load resistance 10 ohms internal impedance 3 ohms dead weight 7 g
The disposal price has been reduced. Member prices are not applicable. 2023/10/23 sales price 29,800 yen ※Currently sold. Comes with a special case! Portable headphone amplifier with built-in D/A converter. DSD256 (11.2 MHz/1 bit) PCM supports native playback of up to 768 kHz/32 bit. Please enjoy the sound quality unique to a thick mojo in the mid to low range. There is dullness and a feeling of use (Sasaki Shota)
Maintenance information: 2023.10.23 Operation confirmed
Accessories: original box
Main specifications: output level 35 mw/600 ohm, 720mw/8 ohm, output impedance 0.075 Ω, dynamic range, 125 dB input system, 3 optical systems, 1 coaxial x 1, microUSB x 1, 2 output systems, headphone jack x 2, charging time, approx. 5 hours continuous operation time, approx. 8 hours W82 x H60 x D22 mm 180 g
A headphone amplifier compatible with headphones with various impedances, from foreign-made headphones with high impedance to headphones made in Japan with low impedance. The high-frequency sound is very beautiful, and the sound is transparent, and you can feel a sense of realism. Equipped with a speaker terminal, it can be used as a simple pre-main amplifier. The exterior is dull. Serial HD53R062.5045005 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: power cable, instruction manual
Main specifications: 1 input RCA, 1 XLR system, 1 output speaker system, 2 headphone systems W217 x H51 x D391 mm 2.6 kg
The stylus is good, but since the cantilever is curved, it is inexpensive. A mono-only cartridge with a traditional 33 series body. Play mono records clearly with a pick-up that is only horizontally oriented. It has vertical compliance and is optimized for recurrent mono editions in the stereoca era. The range is wider than Denon's DL-102 and you can feel the expansion (Fujisawa Yukishi)
Maintenance information: 2023.8.29 Operation confirmed
Accessories: needle cover
Main specifications: MC type needle pressure 2.3 to 2.7 g (2.5 g standard) Muku round needle high hardness duralumin cantilever PCOCC coil anti-vibration rubber “honeynight” impedance 10 ohms 6.9 g
MC cartridge using LC-OFC (linear crystal/oxygen-free copper) wire based on DL-103. Familiar sound with a wide range. The supple sound makes it comfortable to listen to. The exterior has a feeling of use, such as dullness on the body. Serial 4126 (Hiroki Aso)
Maintenance information: 2024.4.21 sound output confirmed
Accessories: none
Main specifications: MC type output 0.25 mV, proper needle pressure 2.2 to 2.8 g, internal impedance 13 ohms, own weight 8.5 g
When connected to a speaker, it reduces speaker impedance fluctuations in the mid to high range. More faithful speaker driving is possible, speaker resolution and stand-up are improved, and natural afterglow is also reproduced. There are scratches on the exterior. Serial 00753, 00754 (Fujisawa Yukishi)
Accessories: instruction manual, original box
Main specifications: W100 x H47 x D117 mm approx. 190 g/piece
※Overall, there is dullness, rust, and scratches, and there is a feeling of use, so it is inexpensive. A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. (MIZUSAKI Ryo)
Maintenance information: 2024.1.27 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
The price has been reduced! 2024/4/21 sales price 39,800 yen This is a compact Dali speaker with an attractive sound that is warm and feels good against the skin. They play vocals, chamber music, etc. comfortably. The exterior is dull. Serial 5431394, 5431394 (Fujisawa Yukishi)
Maintenance information: 2024.4.21 operation confirmed
Accessories: original box, saran net
Main specifications: Playback frequency characteristics approx. 45 Hz to 30 kHz crossover 2.5 kHz/14 kHz input sensitivity approx. 86 dB impedance 6 ohms recommended amplifier output 25 to 100 W W150 x H325 x D260 mm 4.8 kg
It smells like an air freshener, and since ATT has cracks, it is cheap, and is currently discontinued. A bookshelf type speaker that uses a uniquely developed hard dome unit. It is a speaker characterized by a well-balanced, clear, and bright sound. There are small scratches, dents, and net holes (Daiki Goto)
Maintenance information: 2024.3.12 operation confirmed (with ATT gaps)
Accessories: none
Main specifications: 3 way 3 speaker bass reflex system frequency band 30Hz to 30kHz impedance 6Ω sound pressure level 94 dB dimensions W390 x H710 x D350 mm weight 27.5 kg/book
A classic MC boost transformer. With 2 input systems, an impedance of 3.40 ohms switchable, and a PASS line, you can freely enjoy a variety of cartridges and tone arms. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.11.18 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input, 2 systems, switchable, 1st order impedance 40 Ω, 3 Ω, switching, 2nd order impedance 4 kΩ, boost ratio 1:10, frequency characteristics, 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. There is dullness and a feeling of use (Sasaki Shota)
Maintenance information: 2024.3.30 Operation confirmed
Accessories: manual
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
※Since the cantilever is slightly raised, it is inexpensive. Mid-range models in the MC Star series, which come in 3 types. Both models have different sounds, and they are all unique, but 20W is a model that places particular emphasis on the mid-range. The sound is warm in tone, and has an extrusive, and comfortable sound that goes through the SPU. The wooden body made of Yamanaka lacquer, which is a traditional Japanese craft, is also beautiful.
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: none
Main specifications: MC type output voltage 0.5 mV suitable needle pressure 2.3 g recommended load impedance 10 to 200 ohms dead weight 10.5 g
A classic MC boost transformer. With 2 input systems, an impedance of 3.40 ohms switchable, and a PASS line, you can freely enjoy a variety of cartridges and tone arms. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2023.12.18 operation confirmed
Accessories: none
Main specifications: MC boost transformer input, 2 systems, switchable, 1st order impedance 40 Ω, 3 Ω, switching, 2nd order impedance 4 kΩ, boost ratio 1:10, frequency characteristics, 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.2.13 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
Maintained! The 306 series was supported as a pure audio entry model. It has plenty of phono circuits, is MM/MC compatible, and impedance can be adjusted. Clear, high quality sound quality with W super servo system. I feel that the sound quality, which has a slight core, is good in this era. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.22 maintenance completed (mode, recout, input, subsonic, cartridge, phono selector switch disassembly, polishing grease application, replacement of all indicator lamps, solder repair, pin jack polishing, internal inspection and cleaning, each volume, switch cleaning, operation confirmation)
Accessories: instruction manual
Main specifications: PHONO (MM/MC) 2 system frequency characteristics 0.8 Hz to 170 kHz dimensions W480 x H100 x D403 mm weight 10.5 kg
The price has been reduced! 2024/4/11 sales price 45,000 yen Woofer edge softening treatment was completed in March 2021! The sharp mid-high range, which is typical of a diamond tone, is characteristic. The low frequency thickness unique to 30 cm is also attractive, so you can enjoy it in all genres. There are some dents on the exterior. Serial 16747/16900 (Yonejima Satoshi)
Maintenance information: 2021.3.6 Maintained (softened)
Accessories: saran net
Main specifications: 3 way 3 speaker sealed impedance 6 Ω playback frequency band 35 Hz-35 kHz crossover 500 Hz/4 kHz maximum input 230 W sound pressure 91 dB W380 x H680 x D325 mm 27 kg
The price has been reduced. 2024/2/20 sales price 49,800 yen 2-way bookshelf speaker system. It's the most compact speaker in the company's 600 series, yet it's second to none in terms of power and accuracy due to the new separate double dome tweeter and design improvements. It is in good condition (Sasaki Shota)
Maintenance information: 2024.2.20 sweep test good
Accessories: none
Main specifications: playback frequency 54 Hz to 50 kHz efficiency 85 dB impedance 8 ohm crossover 4 kHz dimensions W160 x H315 x D229 mm weight 4.6 kg
*The headshell is an SPU-G (M) one, but the body is inexpensive because it is GE. Needle cover missing. G-shell oval needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal staple cartridge that fully conveys the original appeal of analog. The exterior has rust on the metal parts, and dullness and dirt throughout the body. The needle tip is in good condition (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
*Needle cover missing. G-shell elliptical needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal cartridge that fully conveys the appeal of analog. There are slight corrosion irregularities on the shell (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
G-shell oval needle model from the Herman era. The glossy, rich, and heavy sound is an appeal that never fades. It is an eternal cartridge that fully conveys the appeal of analog (Yasuhito Koshihama)
Maintenance information: 2024.4.25 storefront operation confirmed
Accessories: original box
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
Maintained! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, there is a feeling of use, such as paint peeling off and scratches scattered around. Serial 17041 17049 (Hiroki Aso)
Maintenance information: 2023.3.31 Maintained (terminal rust removal, acid wash, insulating bushing & mounting screw replacement, ATT brand new replacement, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound output check)
Accessories: none
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
※1 bottle only. Maintained! This is a rare blue frame (above) model LX5. The impedance is 8 ohms, and the cross is 500 Hz, so be sure to use a 175 or 375 driver that uses 8 ohms! There are spots, rust spots, and small scratches. (Honda Maki)
Maintenance information: 2021.12.21 Conductivity confirmed 2019.4.4 Maintained (re-fix the internal coil with silicone agent. Remove rust from terminals and mounting screws, clean, and tighten. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: No accessories
Key Specifications: Crossover Frequency: 500 Hz Level Control: 3 Position Switch Input Impedance: 16 ohms 159 x 153 x 120 mm 2.3 kg
Maintained in October 2022! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, paint is bald and oxidized (Yonejima Satoshi)
Maintenance Information: 2022.10.7 Maintained (Terminal rust removal, acid cleaning, insulation bushing & mounting screw replacement. ATT replacement A frequency characteristic measurement check (~ approx. 42 kHz) was performed, and the original capacitor was continuously used for good results. Input/output waveform and balance check, sound output check.)
Accessories: no accessories
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
Maintained! A network with a crossover frequency of 7 kHz. It is ideal for MID/HIGH for 3-way systems using 2440. There is a small wound (Oikawa Tetsuji)
Maintenance information: 2024.4.17 Maintained (2 VR attenuators, 12 screws, 24 insulating washers replaced)
Accessories: none
Main specifications: crossover frequency 7 kHz, allowable input (continuous program), 50 W impedance, bass range: 12 to 16 ohms, treble range: 12 to 16 ohms, treble attenuation/variable volume, mounting hole W140 x 108 mm 0.7 kg
SPU-GE reprint model. This is a popular oval needle type. It is a cartridge where you can feel the depth of analog. The rich texture and thick outline set it apart from other cartridges. It's very slightly to the right. Serial 718026 (Takasaki Atsushi)
Maintenance information: 2024.4.20 sound output confirmed
Accessories: original box, needle cover
Main specifications: G shell oval needle MC type output 0.2 mV suitable needle pressure 4 g internal impedance 2 ohms dead weight 30 g
It is the SPU “number one” newly created with the goal of reproducing the thickness and thickness of the sound of old SPUs of yesteryear. Among them, the #1S is a cartridge that uses a round needle, and a wide range is also added. Serial 312009 (Kanai Hidetsugu)
Maintenance information: 2024.4.23 sound output confirmed
Accessories: original box, instruction manual, needle cover
Main specifications: round needle output voltage 0.18 mV internal impedance 2 ohms needle pressure range 3.0 to 5.0 g dead weight 30 g
It is the SPU “number one” newly created with the goal of reproducing the thickness and thickness of the sound of old SPUs of yesteryear. Among them, the #1S is a cartridge that uses a round needle, and a wide range is also added. Serial 242699 (Kanai Hidetsugu)
Maintenance information: 2024.4.23 sound output confirmed
Accessories: original box, instruction manual, needle cover
Main specifications: round needle output voltage 0.18 mV internal impedance 2 ohms needle pressure range 3.0 to 5.0 g dead weight 30 g
The price has been drastically reduced! 2024/4/17 sales price 69,800 yen ※It is cheap because it has a tobacco smell. Hi-Fi Man's planar drive headphones have a high resolution, and the low frequencies are clear and easy to listen to. The sound balance is flat and the high cushioning is also impressive. The exterior smells like tobacco and there are creases on the cable (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box, connection cable
Main specifications: planar drive impedance 50 ohms sound pressure sensitivity 83.5 dB playback frequency band 8 Hz to 65 kHz 505 g
The price has been drastically reduced! 2024/3/17 sales price 69,800 yen JBL professional tweeter. Since it is designed to make the sound fly far, the sound quality is solid and more straight compared to the company's consumer model 077. The mid to high frequencies are vivid, and the low frequencies are finished with a tight sound. The exterior has dullness and small scratches due to aging. Serial 81380/52416 (Yonejima Satoshi)
Maintenance information: 2024.3.17 sweep test good
Accessories: No accessories
Main specifications: horn type tweeter impedance 16 ohms playback frequency band 6,500 to 21,500 Hz (manufacturer specified), crossover 7 kHz, efficiency 105 dB, W100 x D84 mm, 3 kg/book
The price has been reduced! 2024/4/13 sales price 69,800 yen ※It is cheap because it has a tobacco smell. It is a premain amplifier with a built-in USB DAC compatible with a maximum DSD of 11.2 MHz and PCM384 kHz/32 bit input. Adopts a dual monaural configuration/fully balanced circuit design that inherits the design philosophy of the UD-503. This one is enough, and it's a convenient dish. There are small scratches on the exterior. Serial 1710182 (Tamura Eiji)
Maintenance information: 2024.4.13 operation confirmed
Accessories: remote control, power cable
Main specifications: 20W+20W (8Ω) impedance 4Ω to 8Ω frequency characteristics 10Hz to 100kHz W290 x J81.2 x D264 mm mass 3.7 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/2 sales price 79,800 yen Hi-Fi Hall first arrival! A compact and elegant DALI tall boy speaker with sharp low frequencies and clear midrange, and an airy treble range. The exterior has a scratch on the stand, a scratch on the side of the main unit, and a small scratch on the top plate. Serial 6255811 (Sato Wataru)
Maintenance information: 2024.4.2 sweep test is good
Accessories: instruction manual, spike, saran net
Main Specifications: Frequency Characteristics: 39~26kHz 88dB Impedance 4Ω Tweeter 29mm Soft Dome Midrange/Woofer 130mm/SMC Wood Fiber Cone Driver ✕ 2 Dimensions W162 ✕ D283 ✕ H830mm Weight 10.8 kg
The price has been reduced! 2020/11/9 sales price 70,000 yen maintenance completed. This is a 2-way network. Since bass can be pushed out well, and high frequency adjustment ranges can be obtained with 2 types of HF/MF attenuators, it is a model that is easy to match the desired sound quality. There are small scratches on the exterior due to the feeling of use. Serial 05234 07210 (Makoto Kono)
Maintenance information: 2020.11.9 maintained (common wiring reinforcement terminal solder removal, rust removal treatment, cleaning, ATT (x4) contact disassembly cleaning, contact grease application, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound check)
Accessories: none
Main specifications: W114 x H190 x D228 mm 1.8 kg Crossover frequency 1.2 kHz Impedance 8 ohms Level control is continuously variable up to -8 dB in the middle range is 2 kHz and the high range is continuously variable up to -6 dB at 10 kHz
The sound of the shell, which determines the rich sound of the SPU called the “core of the MC cartridge,” is enhanced by blending wood powder and resin. It is a modern SPU that combines the softness and intensity of the classic series sound. It's very slightly leaning to the left. Serial 730862 (Takasaki Atsushi)
Maintenance information: 2024.4.20 sound output confirmed
Accessories: original box, needle cover
Main specifications: MC type output voltage 0.2 mV impedance 2 ohms frequency characteristics 20 to 25,000 Hz internal resistance 6 ohms diamond needle nude elliptical (elliptical needle) suitable needle pressure 4 g dead weight 32 g
The price has been drastically reduced! 2024/4/3 sales price 79,800 yen CASTLE's small studio monitor is in stock for the first time at Hi-Fi. A special version of the model that has received high praise since its inception. Even though it is crowned with a monitor, you can feel the high level of texture unique to being made in England that is easy to listen to. You won't get tired of listening to the supple sounds of vocals and strings. The exterior is a saran net, and there are small scratches on the main body. Serial BJH0009 (Yonejima Satoshi)
Maintenance information: 2024.4.3 sweep test is good
Accessories: saran net
Main specifications: 2-way rear bass reflex type frequency characteristics 60Hz-20kHz output sound pressure level 88dB rated impedance 8Ω W165 x H280 x D235 mm 5.1 kg