Maintained in 2023! Hammer tone BBC specification! Strobe platter included! This is a combination of GARRARD 301 and SME 3009S2, which has an attractive gripping, and gutsy sound. The high sensitivity short arm with high utility and the sound produced from the idler turntable is exhilarating and very comfortable. It is a record player system that allows you to experience the true essence of analog. Since the shaft on the back of the motor is long, an Audio-Technica insulator is included. *Currently, the pulley has a 60 Hz specification, but the strobe platter is for 50 Hz (Murakoshi Yoichi)
Maintenance information: 2023.8.15 maintenance (motor disassembly/check, lubrication, assembly. Main bearing disassembly, cleaning, oil injection, oil sealant application, assembly. Overall cleaning. idler cleaning Motor suspension spring rubber replacement. Transport plate fixing clip. Linguage distortion correction. Noise suppressor rebuild replacement. Mount rubber washer added. 50Hz pulley adjustment added. SME3009S2 cleaning. Mount grommet replacement Contact cleaning. (Running test)
Accessories: insulator (audio technica AT616)
Main specifications: 301: idler drive 33, 45, 78 rotations compatible 3009S2: short arm static balance type, total length 265 mm, overhang 15 mm, needle pressure (when 1 rider weight is attached) 1 memory 0.25 g step 0 g to maximum 2.5 g (when 2 rider weights are attached) 1 memory 0.5 step 0 g to maximum 5 g cartridge dead weight up to 28 g size W480 x D406 x H238 mm weight 12.5 kg
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Maintained! An amplifier with a black panel that exudes chic calm. Rather than being glossy like the PRA-2000, it sounds clear and straightforward, and has a sense of unity. It's an excellent product that blends in smoothly no matter what amplifier you combine it with. There are scratches on the exterior. Serial 6111100015 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (PHONO selector, tape monitor selector, SW disassembly contact polishing, cleaning, and grease application due to poor contact between each. (Improved by cleaning the balance VR and main VR contacts, and check the sound output for each other input/output connection.)
Accessories: instruction manual
Main specifications: MC/MM input with CD direct input W466 x H136 x D302 mm 6.3 kg
The price has been reduced. 2024/3/23 sales price 20,000 yen*Currently sold. Both center caps have dents, and the dowel rubber on one side of the saran net is missing, etc., so the condition is poor, so it is inexpensive. Victor's 3-weight dollboy speaker It is a masterpiece that combines a glossy sound that spans the entire area with a clear mid-range. It is characterized by a clear sense of transparency in mid and high tones, and shows its true value with female vocals, etc. In addition to the appearance described above, there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.3.23 Operation confirmed
Accessories: instruction manual, saran net, jumper
Main specifications: 3-way 4-speaker system bass reflex type (anti-magnetic JEITA) 32 Hz to 80,000 Hz W300 x H1029 x D345 mm (including foot part) 22 kg
1.6m pair of unprocessed 0.12mm x 238 (OFC) speaker cables This cable has a sense of volume in the mid to low range and is compatible with a wide range of devices (Tomoho Asaine)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
Speaker cable, 5,0m pair, untreated ends, an introductory cable that is soft and easy to run. The medium range is easy to hear and has a sense of volume, making it perfect for upgrading from accessories. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
The company's best integrated amplifier designed by generously pouring the technical power of the Si 3000. The design, such as dual mono construction, the shortest signal path, and the chassis created by making full use of alloy technology, is also a masterpiece that gives off its own unique personality. The driving power is excellent in the smooth mid-high range with a high sense of SN, and in the mid to low range with a high sense of sound pressure. The highest amount of information as a premain amplifier is attractive. There are small scratches on the exterior. Serial Y 2008 (Yonejima Satoshi)
Maintenance information: 2024.4.17 Maintained (SP knob removal screw correction and cleaning. Cord clamp misalignment fix screw misalignment fix Internal inspection, cleaning, remote control, light reception check. Bias and offset checks. (Voice check for each input/output)
Accessories: remote control, instruction manual, power cord
Main Specifications: Output: 175W+175W (8Ω) Input Terminals: RCA LINE x 5 (Caldas Rhodium Plating), XLR LINE x 1 (No. 2 HOT) Output Terminal: RCA x 2 Frequency Characteristics: 10Hz - 35kHz
W450×H170×D480mm 27kg
The price has been reduced. 2024/4/17 sales price 128,000 yen Maintained! Quad control amplifier The famous machine 44 has been refreshed by changing the back terminal to an RCA specification that is easy to handle. It's a perfect balance between freshness and richness. When paired with speakers made in England, you can enjoy a calm, high-quality sound (Daiki Goto)
Maintenance information: 2024.4.17 maintained (internal all checks, B-filter capacitor deterioration, +- 18V drive Tr leak large, rectifier diode failure instability → replacement power SW spark killer broken → replacement. C and R checks within each board. *There is a sound leak at main volume 0. (Create 2 1.5m DIN5 cables)
Accessories: copy of instruction manual, power cable, connection cable
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321×H103×D203 mm
RCA cable uses 1.2 m pair of high-purity oxygen-free copper with super annealing treatment, 2-core shielded high-density braided structure, and high-grade gold-plated plugs with precision machining. The sound quality is stable, natural, and has no sense of emphasis. There is a feeling of use such as dullness on the exterior (Asae Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
The disposal price has been reduced! (Member prices are not applicable) 2024/4/8 sales price 198,000 yen Maintained! Macton tubular OTL stereo power amplifier. Eight 6RA3 triodes are used in parallel per channel to enhance load impedance adaptability, and it also features a structure with Macton's unique balanced NF applied. The sound unique to OTL is thick and has a high sense of energy, and the high driving power is also attractive. The appearance is oxidized and dull. Serial 40704 (Yonejima Satoshi)
Maintenance information: 2024.4.8 Maintained (power transformer primary side rewound repair by PSE inspection. 3 vacuum tube 6RA3 replacements Vacuum tube 6AQ8 replacement. Main volume disassembly cleaning repair. Vacuum tube socket and RCA jack caulk repair. Operation has also been checked with AC 100V (rated output 32W, SP:16Ω), please use speakers above 16Ω)
Accessories: No accessories
Main specifications: tubular low-load OTL stereo power amplifier 30W x 30W (8Ω) vacuum tube used: 6RA3 x 10/6RA8 x 2/12AX7 W370 ✕ H160 ✕ D270 mm 12 kg
The price has been drastically reduced.” 2024/4/16 sales price 298,000 yen An analog player representing LINN. This combination is equipped with a VALHALLA (Valhalla) power supply with the quietest and most accurate drive, and an ITTOK LV2 with firm and high rigidity on the arm! The large number of sounds unique to the LP12, the appeal of the tone, and the rich sense of scale sound quality are attractive. ※The turntable seat is an unoriginal one. Externally, there is oxidation on bumps and weights. (FUJISAWA KOSHI)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: Hinges are being arranged
Main specifications: belt drive floating VALHALLA power supply (33 rotations only) arm/ITTOK LV2/dynamic balance type/cartridge dead weight 2 to 15 g/needle pressure range 0 to 3 g/0.1 g step dimensions W445 x H140 x D356 mm weight 10.5 kg
The price has been reduced. 2024/4/18 sales price 1,180,000 yen 800 Series Diamond advanced model. It reproduces a realistic sound field space that is extremely clear and has a high degree of transparency. The installation area has been reduced to fit the 800 Diamond into a living space, and it is a high-end machine that has both tightness and a sense of volume, and boasts a well-balanced mid-low range even at low volume. There is a light dent in the tweeter grille. Serial 0004457/0004458 (Murakoshi Yoichi)
Maintenance information: 2024.4.18 sound output confirmed
Accessories: spike, transport lock, saran net jumper cable
Main specifications: 3-way bass reflex diamond dome tweeter x 1, warven kevlar cone midrange x 2 lohasel cone woofer playback frequency band 27 Hz to 33,000 Hz sensitivity 90 dB impedance 8 ohms crossover frequency 350 Hz/4 kHz dimensions W368 x H1135 x D563 mm weight 72 kg/unit
The price has been reduced! 2023/4/16 sales price 668,000 yen pure A grade stereo power amplifier. Precise sound particles overlap over and over to create a thick sound. It is an amplifier where you can catch a glimpse of the essence of Accuphase, which is close to the core of music by thoroughly refining physical characteristics. Not only is the sense of power and powerful bass, but the contoured, stretchy mid-to-high range is still appealing. There are scratches and scratches on the exterior. Serial F4Y151 (Fujisawa Yukishi)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: instruction manual, power cord (general purpose)
Main specifications: A grade 60W+60W (8 ohms) dimensions W465 x H238 x D545 mm weight 45.1 kg
The deteriorated vacuum tubes etc. were replaced in 2023 and full maintenance has been completed! The vintage MC30 is still loved today, half a century later. The sharp high range and thick low to mid range sound are nothing short of wonderful. Since the left and right sides come out clearly without interference, you can feel a better sense of localization than a stereo machine. The good separation unique to mono amplifiers stands out, and it can play everything from jazz to classical music well (Murakoshi Yoichi)
Maintenance information: 2023.6.10 maintained (vacuum tube socket re-caulking repair, vacuum tube 12AX7 replacement, selenium countermeasure diode addition, 2W and 1/2W resistor replacement, HUM ADJ. readjustment/RCA jack re-caulking repair, operation check (measured at 25-38W SP:8Ω with rated output AC100-117 V).)
2012.6.12 Maintained (Capacitor Exchange/Mallory x 2, Sprag x 2, Europe x 2, Black Beauty x 10, Cornell x 2, Vacuum Tube, Partially Replaced with Good, Used, Silicon Rectifier, Vacuum Tube Pin, Rust Polishing and Socket Electrode Sack, Bolum, Sliding Surface Cleaning, RCA Pin Jack Cleaning, Each Voltage, Operation Inspection)
Accessories: none
Main specifications: rated output 30W, input sensitivity 0.5V vacuum tubes 6L6GC x 2, 5U4 x 1, 12AX7 x 2, 12BH7 x 1, 12AU7 x 1, W356 x H203 x D203 mm, weight 15.8 kg
The price has been reduced! 2024/4/17 sales price 69,800 yen ※It is cheap because it has a tobacco smell. Hi-Fi Man's planar drive headphones have high resolution, and the low frequencies are clear and easy to listen to. The sound balance is flat and the high cushioning is also impressive. The exterior smells like tobacco and there are creases on the cable (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box, connection cable
Main specifications: planar drive impedance 50 ohms sound pressure sensitivity 83.5 dB playback frequency band 8 Hz to 65 kHz 505 g
The price has been reduced! 2024/4/12 sales price 84,800 yen This is a genuine manufacturer stand for B&W805D3. The logo on the bottom of the stand gives off a sense of luxury. It's designed with sound quality in mind, so I think it's worth trying it out. There is dullness and scuff marks. Serial 1942-0007869/1942-0007869 (Fujisawa Yukishi)
Accessories: instruction manual, rubber foot, spike, fixing screw, hex
Main specifications: W255 x H595 x D370 mm 13 kg
We've reduced the price! 2024/2/5 sales price 59,800 yen Manufacturer maintained! The third generation of the Denon 2000 series. Frequency characteristics have been improved and low noise has been achieved by reviewing power parts, volume circuits, etc., while keeping the low frequency range with a sense of volume unique to the company and the high frequency range with elongation unchanged. Of course, it is a big hit model that is compatible with modern sauces, and doesn't make you feel that it's poor to listen to old sources. In addition to dullness and small scratches on the exterior, there is a feeling of use such as slight stickiness. Serial 10212501972 (Hiroki Aso)
Maintenance information: 2024.2.5 maintained (function SW source direct SW disassembly repair SP relay replacement and other parts inspection operation test)
Accessories: instruction manual power cable
Main specifications: output 80W+80W (8Ω) PHONO (MM/MC) bi-wiring compatible dimensions W434 x H180 x D478 mm weight 22 kg
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Line transformer using TANGO's input transformer, NN-600-600. The overall sound resolution is increased, and the sense of sound pressure is also enhanced. Recommended for those using speakers with horn drivers. TANGO badges are discolored, and there are tape marks and bumps on the chassis (Kojima Yosuke)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: none
Main specifications: primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70 H W140 × H110 × D100 mm 1.8 kg (actual measurement, not including protrusions)
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
*Currently sold. Comes with a remote control. Subwoofer system with built-in power amplifier using Yamaha's unique YST system. The deep bass is thick and has a sense of volume, and is extremely effective in reproducing movies and live sound sources. It is a heavy structure using the same wood as GT racks. There is a feeling of use on the exterior due to scratches, dullness, paint peeling, etc. Serial 101034 (Tomonori Asaine)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: remote control instruction manual
Main specifications: floor-type anti-magnetic design amplifier output 120W cutoff frequency 30Hz to 130Hz power consumption 100W dimensions W580 x H440 x D440 mm weight 48 kg
The price has been drastically reduced. 2024/3/18 sales price 79,800 yen ALTEC's royal unit used in A7 etc. It's a woofer with a good sense of clarity and a light sound. It has a sense of dynamism and goes well with jazz and rock (Shota Sasaki)
Maintenance information: 2024.3.18 sweep test good
Accessories: none
Main specifications: 38cm ferrite magnetic woofer, 97db, 8Ω, 20Hz to 1600Hz, weight 9.4 kg, baffle opening diameter 35.9 cm
The price has been reduced. 2024/4/5 sales price 99,800 yen Maintained! It is an impressive British Rogers compact speaker with a crisp grain and a sense of density. I was impressed by the fact that this speaker values analog flavor in a range with a sense of moderation without daring to be greedy, such as a sense of volume or scale in the low range. Serial 1247 (Asaine Tomoho)
Maintenance information: 2024.4.5 maintained (exterior cleaning/repair saran frame painting/net replacement woofer maintenance (edge softening treatment, center misalignment adjustment on one side)
(Detachable unit)
Accessories: Saran net jumper cable (general purpose)
Main specifications: 2 way 2 speakers sealed bookshelf type 45W W190 x H302 x D162 mm 5.0 kg
* There is no problem with the sound quality, but since there is a dent correction mark on the tweeter on one side, it is inexpensive and is currently sold. An authentic speaker that produces well-balanced sound quality from a compact cabinet. The mid-high range, which has a good sense of signal even at low volume, really makes you feel like a modern speaker. Stringed instruments and pianos in particular have a luster and are recommended
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box
Main specifications: 2-way 2 speakers, frequency characteristics, 50 Hz to 26.5 kHz, input sensitivity, 88 dB impedance, 6 ohms, W205 x H351 x D293 mm, 6.3 kg per unit
Maintained by Denon! This is DENON's mid-range model, and is a staple machine with an excellent sense of stability, with firm bass and delicate high frequencies. In addition to the bass energy from conventional models, you can enjoy well-balanced sound that takes into account the high mid to high frequencies with a high sense of transparency. There are small scratches on the exterior. Serial 8061507480 (Tamura Eiji)
Maintenance information: 2024.4.17 manufacturer maintained (Rch amplifier circuit, transistor and resistor replacement. Amplifier board soldering correction (both channels). (Idle current adjustment and operation inspection carried out.)
Accessories: instruction manual, power cable, original box
Main specifications: rated output 80W+80W (8Ω) PHONO1 system (MM/MC switching) dimensions W434 x H181 x D480 mm weight 24.0 kg
The disposal price has been reduced! Member prices are not applicable. 2024/4/12 sales price 188,000 yen The successor to the company's hit model Silver8 debuted at Hi-Fi. The color is HGBK (high gloss black) with a sense of luxury. The low range, which is easy to handle yet has a sense of volume, and the clear mid-high range with a wide range are attractive. There are scratches and scratches on the exterior. Serial 700247, 700247 (Fujisawa Yukishi)
Maintenance Information: 2024.4.12 Operation confirmed
Accessories: instruction manual, spikes
Main specifications: 3-way bass reflex type crossover frequency 570Hz,3.5kHz impedance 8Ω allowable input 200W efficiency 90dB size W185 x H1000xD300 mm W252 x H1034 x D367 mm (base foot included) weight 20.0 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/4/2 sales price 250,000 yen ※We have newly created head amplifier modules ✕ 2, Phono equalizer modules x 2, and flat modules x 2. Maintained! This is a control amplifier from Sony's high-end brand, the Esprit series. Straight Sony sound with a sense of speed similar to the TA-E900. I want to use the look and sound in combination with the company's Power TA-N902. The exterior has small scratches and is dull. Serial 200499 (Takasaki Atsushi)
Maintenance information: 2023.4.2 Maintained (2 flat modules replaced. Check the input/output waveform, check the left and right balance, and connect a power amplifier to perform a comprehensive operation test.)
2023.1.5 Maintained (Phono equalizer module x 2 replaced. Check the input/output waveform, check the left and right balance, and connect a power amplifier to perform a comprehensive operation test.)
2022.8.31 Maintained (head amplifier module ✕ 2, capacitor, semi-fixed resistor, relay, LED, lamp, Capcom, power cord replacement. All SW, VR disassembly and cleaning. Re-solder the deteriorated part of the solder surface of the board. Check the input/output waveform, check the left and right balance, and perform a comprehensive operation test by connecting a power amplifier.)
Accessories: copy of instruction manual
Main specifications: 2 phono inputs, 5 line inputs, 2 pre-out systems, W480 x H105 x D465 mm, 12.5 kg
*Inexpensive because there are multiple scratches on the front panel. This model uses a non-feedback amplifier circuit with discrete components at all stages. High quality parts such as metal film resistors and high quality film capacitors are used in the RIAA circuit. The smooth, high-SN, and delicate expressive power typical of recent models is attractive (Oikawa Tetsuji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: power cable
Main specifications: mm/MC compatible non-feedback equalizer amplifier input sensitivity mm2.5mV/47kΩ or less, MC0.12mV/470Ω W220 x H57 x D228 mm 2.6 kg
Full maintenance, from replacing deteriorated parts to re-caulking each jack and socket! The original Model 7 has arrived. You can enjoy a glossy mid to high range sound with a high sense of transparency and a thick, exquisite balance. It's a model that has been over half a century since it went on sale for analog fans, but it's still one they admire. The lustrous, indescribable tone is an appeal that cannot be enjoyed on modern devices. There is a feeling of use due to appearance, dullness, small scratches, etc. Serial No. 21199 (Kobayashi Hitoshi)
Maintenance information: 2024.4.17 maintenance completed (balance volume slide, front lamp replacement, high pressure selenium diode addition, RCA jack and vacuum tube socket re-caulking repair. AC 100 to 117 V operation checked) 2022.7.15 maintenance (V5 socket pin replacement, operation check) 2022.2.11 maintenance (main volume and balance volume disassembly cleaning repair, subchassis rubber pad replacement, vacuum tube 12AX7 replacement/vacuum tube socket and RCA jack re-caulking repair. Operation check with AC 100 to 117 V) 2019.3.20 maintained (main volume replacement, balance volume disassembly, cleaning repair, low pressure selenium replacement, high pressure selenium diode addition, block capacitor 50 μF, electrolytic capacitor addition/replacement, oil capacitor 0.01 μF, etc. replacement, front lamp original replacement, input ground reinforcement repair, vacuum tube socket and RCA jack caulking repair, operation check)
Accessories: copy of instruction manual
Main specifications: tubular control amplifier, vacuum tube, ECC83/12AX7, 3-stage NF equalizer, NF type step switching control, W453 x H185 x D267 mm, weight 7.5 kg
A wide FM/AM tuner that uses a dedicated large, high-rigidity chassis and piano-black-finished sidewoods. The aluminum tuning dial, which allows you to enjoy an analog-like sense of operation, makes you feel nostalgic, and FM complementary broadcasts are also perfectly compatible. The reception sensitivity is also good, and it lets you hear thick sound. There are no noticeable scratches on the exterior. Serial Z015995VXR (Fujisawa Yukishi)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: power cord, loop antenna
Main specifications: FM/AM tuner reception frequency: 76.0 to 94.9 MHz (compatible with FM complementary broadcasting) external dimensions W435 x H94 x D450 mm mass 5.8 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/4/13 sales price 128,000 yen ※The PHONO board is for MC only (MM cannot be used). Maintained! It has an elegant and glossy tone, and although combinations with 405 are common, 606 etc. are also a good match. It has the natural texture of the acoustic sauce and the smooth tone that feels good against the skin. There are small scratches and paint peeling on the right side. Serial 24151 (Takasaki Atsushi)
Maintenance information: 2024.4.12 maintenance (main board ground point screw reprocessing, operation check) 2024.1.17 maintenance (replacement of coupling C, bypass C, etc. in each board, AC SW spark killer C replacement, INPUT switching analog SW through hole pattern re-soldering, power SW internal contact polishing ~ operation check)
2020.6.13 Maintained (balance VR, SW disassembly cleaning. Attach 1 kΩ resistors to both the left and right sides of the flat board. Replaced due to faulty IC. All flat and mother boards have been soldered again. (Check the input/output waveform, check the left and right balance, and perform a comprehensive operation test by connecting the power amplifier to confirm normal operation.)
Accessories: power cord, copy of manual
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321 x H103 x D203 mm, 4.0 kg
The disposal price has been reduced. Member prices are not applicable. 2023/5/13 sales price 250,000 yen*The main volume, BASS, and TREBLE knob textures are different from the original. Internal parts have been thoroughly reviewed and maintenance has been carried out! This is a control amplifier from Sony's high-end brand, the Esprit series. Straight sound with a sense of speed similar to the TA-E900. The outline is clear and the sound image is drawn clearly. It is a vintage speaker and is especially recommended for jazz and rock fans. On the exterior, in addition to dullness and small scratches, there is a feeling of use, such as sticker marks on the top plate. Serial 200616 (Hiroki Aso)
Maintenance information: 2023.3.4 maintained (running test by refining the I/O board and screw parts) 2022.10.1 maintained (condenser semi-fixed resistance relay LED lamp IC spark killer Capricorn washer replacement implementation all SW VR disassembly cleaning board solder surface re-solder input/output waveform confirmation and left and right balance confirmation comprehensive operation test)
Accessories: copy of instruction manual
Main specifications: 2 PHONO inputs, 5 line inputs, 2 pre-out systems, W480 x H105 x D465 mm, 12.5 kg
The disposal price has been reduced. Member prices are not applicable. 2023/9/13 sales price 2,980,000 yen Maintained with attention to details such as drivers and wiring! The Georgian 4 is attractive for its elaborate horn configuration and beautiful furniture-like design. It is a model with a built-in crispy horn, a structure that creates a unique sound with a rich sense of scale, and the loud sound is truly an American masterpiece, but you can also feel a somewhat English-like sex appeal. *The attenuator has been maintained, but slight chipping occurs when turning due to deterioration of the original winding resistance (Oikawa Tetsuji)
Maintenance information: 2023.9.13 Maintained (828HF disassembly and maintenance: separation from magnetic circuit and diaphragm, magnetic circuit diaphragm maintenance: cleaning of the magnetic circuit, rustproof vibration system, round out, stop noise, T350 disassembly and maintenance: separation from the magnetic circuit and diaphragm, sound pressure difference adjustment: stop noise due to resonance sound generation, elimination of sound pressure drop due to rear sound leakage. Confirm that there are no modifications inside the housing. Remove rust from screws on screw-type terminals, pickle, and polish and clean the receiving side. ATT (x4) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: none
Main specifications: 4-way 15WK, 828HF, T350, X336 (300/3500) approx. W860 x D660 x H1,350 mm approx. 90 kg
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
The original appeal of Arden, where a simple and beautiful design and deep sound coexist, has been revived due to full internal and external maintenance utilizing the original capacitors. This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. The sense of scale of the orchestra and the smooth playback of stringed instruments are satisfying enough to listen to. There are repair marks on the edge of the cone paper on one side and the top surface on one side. The exterior has been beautifully finished due to exterior maintenance. Serial 0016190/0005927 (Murakoshi Yoichi)
Maintenance information: 2024.4.3 maintenance (exterior repair) 2022.5.30 maintained (output terminal contact cleaning. Chassis screw replacement. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (low range side: edge replacement, magnetic circuit rust removal/gap cleaning/center adjustment, high range side: magnetic circuit rust removal/gap cleaning/center adjustment. Exterior repair/polishing/oil finish Front and rear baffles/hakama repair/painting Saran net replacement. (Detachable unit)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
The disposal price has been reduced! (Member prices are not applicable) 2024/4/11 sales price 148,000 yen ※It is cheap because the condition is poor due to noticeable bumps and frayed saran nets. JBL 60th anniversary model. A tall boy who embodies a wide range of modern JBL sounds. It has a smooth, smooth tone, and is compatible with various genres without difficulty. Of course, you can also enjoy a sense of energy with a punch in the mid to low range. The exterior has blows, scratches, and fissures on Saran (Tamura Eiji)
Maintenance information: 2024.4.11 sweep test good
Accessories: saran net, spikes
Main specifications: 3 way 4 speakers 6Ω 90dB crossover frequency 2.5kHz, 8kHz W260 × H1,130 × D430 mm 35.6 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/2/29 sales price 128,000 yen A digital amplifier equipped with a Tripath class T PWM amplifier IC. It beautifully expresses the sense of energy and description. Gain can also be switched on the back, and it is compatible with a wide range of input sources. The exterior is dull and there are scratches on the top of the front panel. Serial 090120022 (Tomonori Asaine)
Maintenance information: 2024.2.27 sound output confirmed
Accessories: power cord instruction manual
Main specifications: output 150W+150W (8Ω) 240W+240W (4Ω) W420 x H98 x D395 mm weight 13 kg
The price has been reduced. 2024/2/15 sales price 69,800 yen ※The remote control lid is out of stock, so it's cheap. Maintained! A preamplifier that can be operated by a full remote control. A familiar quad tone that is natural, easy to listen to and won't get tired of. In addition to volume, left and right balance, input switching, etc., it is fully equipped with functions such as TILT (loudness like function), high pass, low pass filter (2 levels each), etc., making it convenient. The exterior has line scratches on the top plate and threads on the front panel (Mizusaki Ryo)
Maintenance information: 2024.2.15 Maintained (remote control itself disabled → IR sensitivity adjustment VOL (internal) NG → replacement ~ adjustment. Other 006P holder NG → replace. (Poor button response in the remote control → all dismantled contacts polished)
Accessories: remote control, instruction manual, power cord
Main specifications: full remote control control amplifier with PHONO input (mm) W321 x H80 x D255 mm 3.3 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/6/12 sales price 49,800 yen ※1 mono amplifier only. The display lamp visible through the lattice is a transistor mono power amplifier with an indescribable design. As for the sound quality, it is a powerful sound with a sense of overhang while making you feel thick, and the low frequencies are not sluggish, making you listen to a pleasant sound. The exterior is dull all over, scratches on the top plate, etc., and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.6.13 Maintained (output relay contact correction input volume disassembly contact correction protection circuit transistor replacement input terminal polish)
Accessories: none
Main specifications: effective output 150 W, input level adjustment, SNR 110 dB, dimensions W436 x H95 x D328 mm, weight 11.5 kg/1 unit
The price has been drastically reduced. 2024/4/19 sales price 398,000 yen Restored in 2018! The HPD385 is mounted on the domestically produced box Recutangular York. The balance between the 15-inch unit and enclosure volume is excellent, bringing out the appeal of any source. There is no habit in low frequencies with a sense of volume, and it responds smoothly even to delicate high frequencies (Kojima Yosuke)
Maintenance Information: 2018.5.1 Maintained (unit edge replacement. Magnetic circuit slit interior cleaning, center adjustment exterior polishing. Replace the input terminal with a banana terminal compatible product. Output terminal polish cleaning. Faston terminal replacement. ATT cleaning. Check the input/output waveform and balance, and check the sound output. Frequency characteristics were measured and the original capacitors were continuously used because the results were good. Clear exterior finish, rear baffle paint Saran net cleaning, reupholstering)
Accessories: none
Main specifications: 2-way coaxial speaker, equipped with HPD385, 92dB, 8Ω, W611 x H1083 x D410 mm, weight approx. 57 kg/book
The price has been reduced! 2024/4/12 sales price 79,800 yen ※It is cheap because it is in poor condition. Equipped with a coaxial unit, sound localization is good, the high frequencies are clear, and the sense of volume in the low frequencies is sufficient for the size, so you can relax and listen to classical music in small groups. The efficiency is also good, so it's easy to play, and the chic design with the mirror piano paint shines is characteristic. In addition to being scratched, some Saran magnets are missing. Also, there is a slight wobble in the SP terminal on the + side on one side, and one screw that stops the terminal board is missing. (FUJISAWA KOSHI)
Maintenance information: 2024.4.9 operation confirmed
Accessories: saran net
Main specifications: 36Hz to 22kHz 45W 4Ω 93.5dB W207 × H990 × D274 mm 17 kg
The disposal price has been reduced. 2024.4.5 sales price 298,000 yen Maintained. An EX series midsize machine that uses a precise curved baffle shape that realizes perfect time alignment. A new cherry brown color using natural beechwood! It is a speaker with a high degree of perfection that balances the strength of the sense of energy, range, and breadth of sound field at a high level. There are no noticeable scratches. Jumper cables are general-purpose products (Sasaki Shota)
Maintenance information: 2024.4.5 Maintained (ceramic graphite diaphragm coil deformation correction and magnesium cone edge peeling deformation repair. (Tweeter coil deformation repair, mid-range peeling deformation repair)
Accessories: none
Main specifications: phase reversal type tall boy floor type, anti-magnetic design, 3-way woofer, 16cm cone type x 2, mid/tweeter, coaxial 14cm cone type, 3cm dome type impedance, 6Ω playback frequency band, 30Hz to 100kHz, output sound pressure level 88.5 dB, maximum input 160 W, crossover frequency 400 Hz/2 kHz, external dimensions W350 x H1224 x D541 mm, mass 48 kg/tube
Refreshed during interior and exterior maintenance in July 2022! It is an S8R composed of late stage famous units representing JBL. The 075 tweeter is full of realism, with the sound of a driver blowing fire into the thick, dry low frequencies, and a sense of realism that leaves graininess. You can enjoy the real thrill of vintage audio. It is in good condition (Oikawa Tetsuji)
Maintenance information: 2022.7.13 maintained (exterior repair/polishing/oil finish, front and rear baffle/hakama repair/paint, lattice repair/polishing/painting, backing fabric replacement, woofer maintenance (edge replacement, cone paper coating), passive cone paper coating, driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound absorbing material replacement, terminal cleaning), tweeter maintenance (horn polishing, magnetic circuit rust removal, etc.) Gap cleaning, terminal cleaning), network maintenance LX5 (terminal rust removal, acid washing, insulation bush & mounting screw replacement. ATT (SW type) disassembly contact polishing and cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Input/output waveform and balance check, sound output check) N7000 (terminal and screw rust removal, acid cleaning, insulation bush replacement. ATT contact cleaning and contact grease application. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. input/output waveform and balance check, sound output check), unit detachable diffuser repair)
Accessories: none
Main specifications: 3 way 3 speakers 1 passive radiator system low range unit 38cm cone type LE15A, medium range unit horn type 375, high range unit 075, passive radiator 38cm cone type PR15, network LX5/N7000 sound pressure level 95dB allowable input 125W W1020 x H670 x D510 mm 82 kg/book
1.8 m PSE standard power cable, 4 types of hybrid original conductor+3-core structure, this is a long-selling cable that reproduces a sense of expanding sound field, medium to high range with good coverage, and a wide range. (FUJISAWA KOSHI)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: original box
The price has been reduced. 2024/3/23 sales price 16,800 yen ※There is no problem with operation, but it is currently sold because it is cheap. A speaker equipped with a C-CAM (Ceramic Coated Alminium Magnesium) driver and characterized by a high range of up to 30 kHz. It makes me hear the sense of SN and transparency typical of modern speakers. There are no noticeable scratches on the exterior, but there is stickiness on the rubber part (Oikawa Tetsuji)
Maintenance information: 2024.3.23 Operation confirmed
Accessories: original box, instruction manual
Main specifications: 2-way bookshelf type, anti-magnetic rear port, bass reflex impedance, 8 ohms, efficiency 88 dB, efficiency, 88 dB, frequency characteristics, 55 Hz to 30 kHz, W165 x H260 x D 180 mm, weight: 3.86 kg
The price has been drastically reduced. 2024/3/2 sales price 99,800 yen Maintained! professional monitor amplifier It has strength unique to commercial use, and the driving power in the low range is truly remarkable. However, it also has a strong sense of temperature typical of a quad, so it is an amplifier that I would like people who are shunned when the sound is too straight for commercial use to try it once. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.3.2 maintained (internal dismantling all check, Tr, C, R check, ±B INPUT bypass C replacement, Tr, R, etc., all OK, INPUT photocoupler check, operation check)
Accessories: copy of instruction manual, power cord, dedicated SP cord (cable length 2.5 m)
Main specifications: 100W+100W (8Ω) W483 × H88 × D310 mm 12.5 kg
The price has been reduced. 2024/4/6 sales price 69,800 yen This 1-inch screwdriver has been maintained (replaced in pairs with JBL D8R2425 due to a broken diaphragm) and has an impressive high range with a smooth, stretchy high range. Compared to the LE85, you can enjoy a natural sound with a sense of depth. As for the sound of a JBL, I get the impression that it is mild. There is a scuff mark on the back (Daiki Goto)
Maintenance information: 2024.4.6 maintained (diaphragm broken (replaced with diaphragm D8R2425)). Parts replacement DCR (38378/3.2 ohm diaphragm no scratch) DCR (38054/3.1 ohm diaphragm no scratch))
Accessories: none
Key Specifications: 1 inch driver, 8 ohm, crossover, 500 Hz, 108 dB, diameter: 114 x D98 mm, weight: 4.1 kg
*There is a gap in the display panel, which is the current situation. This is the model number DCD-1650 gold model representing DENON. Although it is the first model, the sophisticated design is beautiful. There is a sense of transparency in the mid to high frequencies, and the low frequencies are thick and gentle. In terms of functionality, the range of uses has also been expanded, such as installing a program play of up to 20 songs. There is a slight gap left in ATT. Serial 106154518 (Mizushima Itsuro)
Maintenance information: 2018/4/12 manufacturer maintained (pickup, belt, gear, relay replacement. Solder correction, operation confirmation)
Accessories: copy of instruction manual
Key Specifications: 20-bit Lambda SLC-D/A Converter with pitch control W470 x H122 x D360 mm 11.3 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/2/10 sales price 198,000 yen Maintained! According to the 117V specification of the tubular mono FM tuner, reception is unstable at 100V. The Japanese band has been changed, and reception sensitivity is good. It is a tuner that strongly shows the characteristics of Mackin's sound, which is thick, soft, and glossy. There is corrosion and rust throughout the exterior. Serial 292099 (Tomoho Asaine)
Maintenance information: 2024.2.10 Maintained (meter readjustment with coil and right side volume, left side lamp off replacement, IF/RF/MPX readjusted)
2018.2.22 Maintained (VT12AT7 replacement/MPX section transistor replacement/RF/IF/MPX re-adjustment)
2016.1.25 Maintained (6 additional VT shortages. 2 VT replacements 4 additional ceramic C for BAND EX Ceramic C replacement Chemical C exchange. Front lamp repair, block.C50uf x 4 replacement Step up transformer 100V ⇒ 117V added)
Accessories: 117V step up transformer
Main specifications: FM dedicated tuner W400 x H130 x D300 mm 8.6 kg
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an unprocessed 1.1 m pair end. It is a cable with thickness and a sense of extrusion in the mid-range (Murakoshi Yoichi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: none