The price has been drastically reduced. 2023/11/26 Sales price 128,000 yen Maintained in 2022/6! An eye-catching power amplifier with its black and large power meter typical of Sansui. It entertains me with its power, which can be felt from its appearance, and its supple, stretchy sound quality. The exterior has dullness, scratches, rust, etc. over time (Oikawa Tetsuji)
Maintenance information: 2022.6.23 Maintained (both channel volumes replaced. SP relay bad contact replacement. Replace protectors, deteriorated transistors, resistors, and diodes in meter boards. Replace deteriorated transistors and resistors in the power supply board. Replace deteriorated transistors and capacitors in the drive board. OUTPUT selector switch cleaning. (General adjustment)
Accessories: none
Main specifications: left and right independent 2 power supply diamond differential circuit effective output 110W+110W (8Ω) load impedance 4 to 16 ohms W482 x H187 x D450 mm 20.3 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/3/21 sales price 128,000 yen Maintained! This amplifier marked the end of the X series, which began with the AU-X1. It is a model with a weight of 35 kg and a solid investment in material volume. You can enjoy a powerful Sansui sound with full torque. Sidewoods are non-genuine products. There are several bruises and letter rubbing on the front panel and side panels (Murakoshi Yoichi)
Maintenance information: 2024.3.16 maintenance (phono circuit relay, power amplifier volume, selector lamp, power switch, power amplifier circuit transistor replacement, equalizer IC, power supply unit floating resistor replacement. Speaker, power amplifier operation, jump, subsonic, MM/MC switching SW disassembly polishing grease application, power amplifier, power supply part solder repair, pin jack polishing, interior and exterior inspection and cleaning, operation confirmation)
Accessories: copy of instruction manual
Main specifications: effective output 150W+150W (6Ω), 110W+110W (8Ω) dimensions W470 x H178 x D486 mm weight 35.1 kg
The price has been reduced! 2024/3/20 sales price 59,800 yen has been maintained! This is a Sansui CD player with impressive audible sound that is both sound and resolution. The D/A conversion unit is equipped with NEWL.D.C.S, a 1-bit D/A conversion system based on crystal oscillation. The board with the side panel is broken, and there are other small scratches and a feeling of use. Serial 609080871 (Fujisawa Yukishi)
Maintenance information: 2024.3.20 Maintained (repair of the mechanical part of the traverse mechanism Assy. Create connection cable connectors. (Replace all front panel operation switches)
Accessories: No accessories
Main specifications: frequency characteristics DC to 20 kHz SNR 105 dB or more W466 x H127 x D397 mm 11 kg
Maintained in 2023/8. The first model in the α607 series. It is characterized by clear, clear mid-high tones and powerful bass. It excels at sharpness and balance, and you can listen to jazz and rock in particular comfortably. This is one car that shines with its high cost performance. There is a feeling of use on the exterior, small scratches, rust, SP terminal discoloration, etc. (Kobayashi Hitoshi)
Maintenance information: 2023.8.1 maintained (May amp circuit transistor replacement, master volume replacement, output relay replacement, solder repair, MM/MC switch disassembly, polishing grease application, cleaning of each volume switch, internal inspection and cleaning, adjustment inspection, operation confirmation)
Accessories: copy of instruction manual
Main specifications: 105W+105W (6Ω) 90W+90W (8Ω) W448 × H160 × D441 mm 15.7 kg
Maintained! Following the technology at the time of development of the advanced C-2302, a balanced configuration was adopted for the advanced α-X circuit and power supply unit. The sense of strength and driving power of the highest class as a premain is attractive. The exterior has a feeling of use over time, with dullness and small scratches scattered around. ※The side panel has been repaired with veneer, but there are floats and cracks. Serial 622093718 (Yonejima Satoshi)
Maintenance information: 2024.3.24 Maintained (Mayi amplifier circuit transistor, diode replacement. Adjust volume, replace output relay. Hendphone relay replacement. Power supply transistor replacement. Disassemble the input selector and other switches and apply polishing grease (turnover, tone, muting, loudness, subsonic, processor, MM/MC switching, power amplifier direct, source direct, reck-out, tape). Solder repair. Each volume, switch cleaning. Internal inspection and cleaning. Mounting screw rust remover. Bias, DC adjustment, operation confirmation. Decorative panel repair. (Adhesive repair with bond G17)
Accessories: copy of instruction manual
Main specifications: 160W+160W (8Ω) 190W+190W (6Ω) phono equipped with advanced α-x balance circuit (MM/MC switching) dimensions W460 x H161 x D446 mm weight 33 kg
Maintained! Sansui's heavyweight power amplifier. It pursues the essence of a power amplifier, and I am particularly impressed by the strength of the low range and the growth in the high frequency range. Can also be used with large speakers. There are abrasions and bumps in places (Kojima Yosuke)
Maintenance information: 2024.3.22 maintained (4 power supply rectifier diodes, 4 fuse replacement protector transistors, 4 speaker relays, deterioration replacement, INPUT selector switch disassembly contact polishing power supply board, power amplifier board, etc.)
Accessories: copy of instruction manual
Main specifications: 110W+110W (8Ω) impedance 4-16Ω speaker output, 2 line input systems, balance compatible, W450 x H176 x D477 (mm) 35 kg
Maintained! Sansui's rare CD player. The firm outline and comfortable sound are attractive. I would like to use it in combination with the company's α series premain for a unified look. In addition to listening to CDs, it also has a convenient function when recording to tape, etc., and has a variety of aspects. The exterior has small scratches and dullness appropriate for the model year (Oikawa Tetsuji)
Maintenance information: 2024.3.20 Maintained (The mechanical fixing parts were manufactured and replaced in 1 pair. The clamper and loading belt have been replaced. The velocity coil has been repaired and corrected. (The tact switch on the operation panel has been replaced)
Accessories: remote control
Main specifications: 1-bit linear & direct conversion system (4DAC) W430 × H127.5 × D397.5 mm 8.8 kg
An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
Maintained in November 2023! The middle class of the Sansui α series. The strength of the bass and the sharpness of the mid to high notes are mixed in a well-balanced manner, so you can enjoy not only jazz, but also various genres such as rock and pop music. The exterior is dull and the top plate is damaged. Serial 637065630 (Tomonori Asaine)
Maintenance information: 2023.11.23 Maintained (disassembling and polishing grease applied to each switch (tone, turnover, loudness, muting, subsonic, power amplifier direct, MM/MC, reckout switch), each volume and switch clean output relay and headphone relay replacement main amplifier and power supply part solder repair, interior and exterior inspection, cleaning, side cover screw replacement operation confirmation when power is turned on (It makes a popping sound, but it stabilizes in a few minutes)
Accessories: copy of instruction manual
Main specifications: effective output 160W+160W (6Ω) 130W+130W (8Ω) damping factor 100 (6Ω) W448 × H160 × D441 mm 20.3 kg
Maintained. The 707 series plays a central role in Sansui. The PHONO2 system is compatible with MM/MC on both sides, and since it is compatible with all MC cartridges, it is a great product that can switch between 2 levels of impedance: low and high. This is an amplifier I definitely want you to listen to records to your heart's content. The exterior has dullness, scratches, and dirt. Serial 823050972 (Tamura Eiji)
Maintenance information: 2024.3.10 maintained (input selector, reck-out, tone switch disassembly, polishing grease application, master volume replacement, output relay, headphone relay replacement, main amplifier transistor, adjustment volume replacement, power supply floating resistor replacement, solder repair, each volume, switch cleaning, pin jack polishing, interior and exterior inspection and cleaning, offset, bias (Adjust, check operation)
Accessories: No accessories
Main specifications: 110W+110W size W460 x H160 x D404 mm weight 15 kg
Maintained. The successor that inherited the sound of the D series. A model where you can feel the uniqueness of Sansui at the time due to the extrusion of low frequencies and the creation of sound. They are energetic, playable, and go great with jazz and rock, and are compatible not only with MM but also with MC, making analog fans happy. There is dirt on the top plate (Sasaki Shota)
Maintenance information: 2024.2.8 maintained (main amplifier circuit transistor, film capacitor, DC, bias semi-fixed volume replacement, output relay replacement, power supply circuit floating resistor replacement, balance volume exchange, input selector, reck-out, tone switch disassembly polishing grease application, each volume, switch cleaning, interior and exterior inspection cleaning, pin jack polishing, adjustment inspection)
Accessories: none
Main specifications: execution output 80W+80W (8Ω) damping factor 100 rated power consumption 200W phono MM/MC compatible W460 x H160 x D404 mm weight 13.2 kg
Maintained! The mid-range α series uses an α-X balance circuit that blocks the effects of noise and distortion from the ground. The smooth, stretchy sound quality is attractive. Designed with CD playback in mind, the sound separation is good, and it is a classic premain that will keep you entertained regardless of genre. The exterior has rust spots, paint bald, etc. (Mizusaki Ryo)
Maintenance information: 2023.2.1 maintained (main amplifier output relay replacement, transistor and capacitor replacement, MM/MC, reckout switch disassembly, polishing grease application, solder main part repair, various volumes, switch cleaning, interior and exterior inspection cleaning, offset adjustment, operation inspection)
Accessories: copy of instruction manual
Main specifications: 90W+90W (8Ω) W448 x H160 x D441 mm 16.0 kg
Maintained! A pre-main amplifier that inherits the sound of the D series and has achieved even lower distortion. A model where you can feel the uniqueness of Sansui at the time in the extrusion of low frequencies and sound creation. It's energetic, playable, and goes great with jazz and rock, and is compatible not only with MMs but also with MC, making it great for analog fans. There is a feeling of use such as dullness, abrasions, corrosion, dirt, etc. (Kobayashi Hitoshi)
Maintenance information: 2023.11.21 Maintained (balance, main volume, output relay, power supply floating resistor, Mylar capacitor, equalizer section op amp replaced. Input selector and other rec outs, tone, subsonic, and muting switches are disassembled and polished grease is applied. (Each volume, switch cleaning, solder repair, interior and exterior inspection and cleaning, adjustment inspection.)
Accessories: copy of the instruction manual
Main specifications: 75W+75W (8Ω) PHONO (MM/MC) W445 x H163 x D403 mm 12.4 kg
※Shipping service. No. 58 Special Feature = 3rd “THE STATE OF THE ART: Supreme Component” Award Selection/New JBL 4345 Detailed Report/EMT927 vs. Torrance Reference/Listen to the Tannoy SRM Series/Infinity “IRS” Anatomy/1981.4.15 issued. Posted models: JBL/4345BWX MCINTOSH/MC2500 VICTOR/TT-801, CL-P10, TS-1 MICRO/SX-8000, HS-80 ONKYO/INTEGRA P-309, INTEGRA M-509 MARK LEVINSON/ML-6AL AUDI-Technica/AT-34E11 ENTRE/EC-30 SME/3012-R SPECIAL TECHNICS/EPC-C100CMK3 FIDELTY RESEARCH/XF-1 SELLESION/DITTON300 KEF/MODEL105.4 KENWOOD/L-08C, L-08M PIONEER/A-980 SANSUI/AU-D907F SONY/TA-AX8 LO-D/TU-1000 LUXMAN/PD300 ADC/ASTRION LINN/ASAK/ S56.4.15 issued. The photograph is a sample, so the actual product may be broken, or there may be markings etc.
3-way speaker for Sansui components. I was able to confirm the sound output. How about using it for a sub or bedroom? There is a feeling of use such as abrasions (Murakoshi Yoichi)
Maintenance information: 2023.5.9 sound output confirmed
Accessories: saran net
Main specifications: 3-way 6Ω 45W W185 x H375 x D270 mm
※Shipping service. Special Issue No. 36 = All Speaker Systems (above) Test of the latest 40 models/Sound Quarterly (listen to new products) /1975.10.1 issue. Published models: CHRYSLER/LAB-1000,2000 YAMAHA/NS-451 ALLISON/ONE, TWO SLESTION/UL6, UL8 OMAL/MODEL TL6 CABASSE/BRIGANTIN INFINITI/2000Ⅱ JENSEN/23 YAMAHA/C-1 SANSUI/AU9900,11000, TU9900 LAX/L-80V TECHNICS/ HY-7600,7200, ST-7600,7200 VICTOR/JA-S91, S71, S51, JT-V71, V51 TRIO/KA-7500, KT-7500 DIATONE/DA-U850, DA-F750, DA-U750 GAS/AMPZILA SAE/MARK2500 ALTEC/9440A RADFORD/HD250, ZD22 DENON/DP-1700, DL-109R ,109D DIATONE/DP-91D YAMAHA/YP-600, YP-1000Ⅱ MICRO/TAKE-5 CEC/BD-7000 OTTO/TP-1200 SANSUI/SR-525 GRACE/G714, G704 DUAL/601,1228,1225. The photograph is a sample, so the actual item may be broken or written on it.
The price has been drastically reduced! 2022/5/1 selling price 79,800 yen It is a masterpiece 505J of domestic enclosure. With enough contents and box noise, it is a highly recommended box for those who use JBL. The excellent design unique to vintage is also attractive as an interior. The appearance has damage such as corner chips and abrasions. * The hakama has been removed, and there are no conversion baffles or mechanical plates. (Satoshi Yonejima)
Accessories: lattice net
Main specifications: W475 × H705 × D395 mm approx. 23 kg/book (actual measurement)
An enclosure that seems to be for Sansui's old system component speakers. The lattice box with legs reminiscent of JBL's Baron and Bicount is really fashionable. The lattice on both the left and right is out of the frame. There are traces of internal remodeling (Fujisawa Koshi)
Accessories: None
Main specifications: opening diameter 212mm (screw pitch 240mm), aperture diameter 110mm (countertop 170mm, screw pitch 140mm), opening diameter 95mm (for bass reflex port/wood screw pitch 118mm), aperture diameter 70mm (Countertop 92mm, Screw Pitch 104mm) 14mm Particle Board, Veneer Finish W500 × H665 × D430mm 15kg