Single bottle sale military high reliability tube ECC83/M8137 equivalent tube code: 641 R3I4 box plate measurement value 46 (rejected value 32) with original box ※The measured values indicate gM values measured with the testing machine TV-7 (Kojima Yosuke)
Accessories: original box
Single bottle sale military high reliability tube ECC83/M8137 equivalent tube code: 641 R3I4 box plate measurement value 48 (rejected value 32) with original box ※The measured values indicate gM values measured with the testing machine TV-7 (Kojima Yosuke)
Accessories: original box
Single bottle sale military high reliability tube ECC83/M8137 equivalent tube code: 641 R3I4 box plate measurement value 52 (rejected value 32) with original box ※The measured values indicate gM values measured with the testing machine TV-7 (Kojima Yosuke)
Accessories: original box
Single bottle sale military high reliability tube ECC83/M8137 equivalent tube code: 641 R3I4 box plate measurement value 42 (rejected value 32) with original box ※The measured values indicate gM values measured with the testing machine TV-7 (Kojima Yosuke)
Accessories: original box
Pair tube direct heat triode tube, white base, made in Slovakia, measured value 76/70 (rejected value 58) with original box*Pairs are determined based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: original box
※Inexpensive because it is in poor condition. Self-made 2way/3way enclosure. The size of the hole is different at the top, with an opening diameter of about 315 mm on the top and about 360 mm on the bottom. There are many peeling veneer, corner pads, scratches, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: W450 x H1056 x D480 mm approx. 33 kg
※1 bottle only. Maintained! The classic model for professional 1" screwdrivers. It is a driver that is installed in many of the company's 43 series, etc., and is easy to balance with various woofers and tweeters (Daiki Goto)
Maintenance information: 2024.4.23 Maintained (diaphragm installation adjustment, replacement of the following parts. DCR (54871, 5.7 ohm diaphragm, no scratches)
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms (measured 10/12 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Fully maintained, including woofer edge replacement and exterior repairs! A rare model is in stock. British Spendall SP100 derived from the German national broadcast monitor. It goes great with classical music, from symphonies to chamber music, as well as European jazz. The elegant expression unique to European models is fascinating. Serial 3918, 3919 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 maintained (exterior repair/polishing/clear finish, saran net replacement, woofer edge replacement, mid edge replacement, all internal faston terminals replaced)
Accessories: saran net, jumper plate
Main specifications: 3-way bass reflex type 8Ω frequency characteristics 45 to 20 kHz 100W W370 x H700 x D430 mm 36 kg
Maintained by the manufacturer! The third generation of the Denon 2000 series. Frequency characteristics have been improved and low noise has been achieved by reviewing power parts, volume circuits, etc., while keeping the low frequency range with a sense of volume unique to the company and the high frequency range with elongation unchanged. Of course, it is a big hit model that is compatible with modern sauces, and doesn't make you feel that it's poor to listen to old sources. There is dullness and a feeling of use. Serial 1050502942 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 manufacturer maintained (main volume and selector switch disassembly contact cleaning. (Idle current adjustment and operation inspection carried out.)
Accessories: power cord
Main specifications: output 80W+80W (8Ω) PHONO (MM/MC) bi-wiring compatible dimensions W434 x H180 x D478 mm weight 22 kg
Genuine Rin Japan A network audio player. It has a simple and modern European design, so you can enjoy a bright sound without getting tired of listening. Not only is it compatible with the LINN system, but it is also equipped with digital output and variable line level output functions not found in the KLIMAX DS and AKURATE DS. There is a thin scratch on the top plate. ※The display is slightly dark, but this is the current situation. Serial 1255165 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 Operation confirmed (Ver. 4.104.518)
Accessories: remote control, power cord
Main specifications: Compatible sampling frequencies 44.1K, 48K, 88.2K, 96K, 176.4K, 192K compatible bits 16-24 bits, output terminals RCA phono (fixed/variable line level output), RCA phono coaxial (digital output) W381 x D360 x H80 mm 4 kg
A model developed for the digital AV era by applying anti-magnetic treatment to the NS-10M. The clear high frequencies stretch comfortably with less color quality. It is useful for a wide range of applications, such as those who are worried about space and for subsystems. There are small scratches and a feeling of use. Serial 104369A, 104369B (Fujisawa Yukishi)
Maintenance information: 2024.4.23 Operation confirmed
Accessories: saran net
Main specifications: 2 way 2 speaker sealed type 8 ohm sound pressure 90 dB W215 x H382 x D199 mm 7.0 kg
Caster specification! TAOC theater youth HT series wide rack. It also has sufficient load carrying capacity, so even those with large devices can use it without worry. Other than one scratch on the pillar, the condition is pretty good. *Shipping costs will be estimated separately. (FUJISAWA KOSHI)
Accessories: instruction manual, felt, logo seal, hex wrench
Main specifications: load capacity 200 kg/1 shelf spacing 180/230 mm W1,680 x H590 x D550 mm weight 65 kg
This is a rhodium-plated model of the long-selling FI-11 series L-type plug FI-12L series. Adopts a new plating method and a newly developed cable clamp to control stable grip and resonance. Improved sound quality and improved durability have been achieved (Kobayashi Hitoshi)
Accessories: none
Main specifications: L type power plug cable, suitable diameter 9.5 mm to 17.0 mm, dimensions: 42.2 x 55.0 x 66.4 mm
The core model of the high-grade power plug “PC Series”. All PSE standard parts are completely non-magnetic. Due to the characteristics of silver+rhodium plating, it has high resolution, high response, and wide range characteristics. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
PSE standard product UL compliant FURUTECH inlet plug is a non-magnetic material design using gold-plated copper screws and stainless steel parts (Kobayashi Hitoshi)
Accessories: none
Unspecified marble board. The top plate and 5 sides have a mirror finish. Use it for amplifiers, CD players, etc. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: W300 x H30 x D450 mm 10.6 kg (actual measurement)
*Set of 3. A gradation cast iron insulator that firmly supports equipment with heavy construction. The excellent damping properties of cast iron and the vibration blocking effect of pinpoint support make the mid to low range blurring clear, and accurate sound images can be obtained. There is a feeling of use such as dullness and small scratches (Hiroki Aso)
Accessories: spike base
Main specifications: Gradation cast iron, matte black finish, diameter 60 x height 45 mm, weight 800 g/piece, plate diameter 35 x height 5 mm
*Set of 3. A gradation cast iron insulator that firmly supports equipment with heavy construction. The excellent damping properties of cast iron and the vibration blocking effect of pinpoint support make the mid to low range blurring clear, and accurate sound images can be obtained. There is a feeling of use such as dullness and small scratches (Hiroki Aso)
Accessories: original box spike base
Main specifications: Gradation cast iron, matte black finish, diameter 60 x height 45 mm, weight 800 g/piece, plate diameter 35 x height 5 mm
with logo! This headshell is popular due to its combination with the Technics and SL-1200 series. It is made of aluminum die-cast with high rigidity, and brings out the characteristics of the cartridge (Hiroki Aso)
Maintenance information: 2024.4.17 continuity confirmed
Accessories: none
Main specifications: Die-cast aluminum, dead weight 10.2 g
Comes with original box! An English QED cable based on a smooth, natural tone, 1.0m pair of RCA cables. It is a character that makes music resonate comfortably with thick sound quality. The exterior is dull (Hiroki Aso)
Maintenance information: 2024.4.23 continuity confirmed
Accessories: original box
A mid-size Shure model equipped with a solid diamond needle. The resolution is high, and the cuts and crisp sound with a sense of energy in the high frequencies are attractive. The exterior has a feeling of use such as dullness (Hiroki Aso)
Maintenance information: 2024.4.23 sound output checked
Accessories: none
Main specifications: mm cartridge output 4.0 mV needle pressure 0.75 to 1.5 g frequency characteristics 20 to 20,000 Hz dead weight approx. 6.5 g
A pair of 2 corian boards with unknown details seems to be just the right size for small speakers, etc. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Accessories: none
Main specifications: W180 x H7 x D270 mm 0.6 kg (actual measurement)
Carbon fiber cleaner ideal for cleaning analog discs. The carbon fiber brush removes dust and static electricity left on the surface of the analog disc. The exterior is dull and has a feeling of use (Tomoho Asaine)
Accessories: none
PSE standard product 4-prong power strip The sound is lively and the music is dynamic. The spread of sound increases, and an image of the sound spreading throughout the room and the body being wrapped in sound comes out. There is a feeling of use on the exterior, such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.4.23 continuity confirmed
Accessories: none
Main specifications: cable part 75 cm, total length approx. 90 cm
This is a set of needle tip cleaning solution and brush. Normally, you can use a dry method with only a brush, and a wet method that uses liquid when the dirt is severe (Hiroki Aso)
Accessories: brush case
Made from Hokkaido Asada cherry wood and African ebony. It doesn't tighten too much as a metal insulator, and it makes the most of the sound of the music. There is dullness etc. throughout the exterior (Hiroki Aso)
Accessories: none
Main specifications: W70×D70×H35mm
Made from Hokkaido Asada cherry wood and African ebony. It doesn't tighten too much as a metal insulator, and it makes the most of the sound of the music. There is dullness etc. throughout the exterior (Hiroki Aso)
Accessories: none
Main specifications: W70×D70×H35mm
The exterior of the woofer mounting clamp, which seems to be a self-made set of 5, has variations in the cutting part, there are corrosion and mounting marks all over, and there is a feeling of use such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: Mounting part, claw depth approx. 12 mm, 27 x 24 x 18 mm
※Only 1 speaker cable, 0.9 m, has an orthodox cab tire structure, and reproduces sound quality that is thicker than the price. There is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.5.22 continuity confirmed
Accessories: none
※Only 1 interconnect cable is a 0.4 m three-core line cable with no terminals. There are exterior, feeling of use, small scratches, scuffs on the sheath, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.9 continuity confirmed
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2022/5/23 sales price 300 yen. *Only one speaker cable uses oxygen-free copper (OFC) as the untreated conductor at the 0.5m end. The sound quality has a relatively flat impression, so you can easily feel the sound quality a notch higher (Kanai Hidetsugu)
Maintenance information: 2022.5.22 continuity confirmed
Accessories: none
Speaker cable A standard cable that has become synonymous with 1.0 m pair of unprocessed speaker cables. It features a stranded wire structure that enables reliable transmission with low noise even in harsh environments such as studios. Monitor-like sound quality with little coloring (Kanai Hidetsugu)
Maintenance information: 2024.3.30 continuity confirmed
Accessories: none
Speaker cable 2.0m pair A standard BELDEN speaker cable nicknamed “sea snake” with untreated terminals. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
IEEE1394A cable 4 pin/6 pin terminal 1.0m audio-technica GATE LINK series iLINK cable Uses PCOCC+OFC hybrid conductors that the company is proud of (Murakoshi Yoichi)
Maintenance information: unconfirmed
Accessories: none
Speaker cable with soldered 0.9 m pair ends It is a solid sound that clearly shows the backbone of an LC-OFC conductor sound. The exterior has a feeling of use such as rubbing and dirt on the sheath (Murakoshi Yoichi)
Maintenance information: 2024.4.11 continuity confirmed
Accessories: none
※The sound output has been confirmed, but since it is not compatible with the manufacturer, it will be handed over as is. It is a cost-effective USB DAC with a built-in headphone amplifier. The DAC is equipped with 2 8-channel DACs “ES9016” made by ESS. The headphone amplifier is also compatible with 4-pin and 3-pin XLR terminals (balanced drive). There are plenty of connection terminals, so you can connect to a PC, CD, TV, etc. The clear and tight sound does not choose any music genre. Serial ODID0019101JP (Mizushima Itsuro)
Maintenance information: 2024.4.22 operation confirmed
Accessories: remote control, instruction manual (damaged), power cable
Main specifications: sampling frequency/USB input (PCM) 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 352.8 kHz, 384 kHz (16, 24, 32 bit) USB input (DSD) 2.8 MHz, 5.6 MHz COAXIAL/OPTICAL/AES/EBU input 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz (16, 24 bit) digital input USB 1 system, COAXIAL2 system, OPTICAL2 system, AES/EBU (XLR3) 1 system analog output unbalance (RCA) 1 system balanced output (XLR3) 1 system (with fixed level/variable switching, with phase switching function) headphone output imbalance (STD) 1 system, balance (XLR3) 1 system, balance ( XLR4) 1 system W296×H101×D271mm 6.3 kg
unopened! Neutrik speakon 2-core connector that can also be connected to a 4-core receptacle (Murakoshi Yoichi)
Maintenance Information: Unopened
Accessories: none
Fidelity-Research headshell Lightweight and highly rigid. It is characterized by an enveloping shape with a thick aluminum press-processed body. There are dullness and small scratches on the exterior (Tamai Jun)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 10g
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
The price has been reduced! 2024/4/7 sales price 1,500 yen A high-precision level instrument that is essential for leveling players. It is a long-selling model with an aluminum body (Tomonori Asae)
Accessories: none
Speaker selector that can be switched by operating a remote control. It is a 3-system switchable type using a large speaker relay, and can also be switched with the main unit button. The exterior is scratched and dull, and there is a feeling of use (Yamato Yuki)
Maintenance information: 2024.4.23 continuity confirmed
Accessories: remote control power cord
Main specifications: 3-system switching W297 x H79 x D137 mm 1.8 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/2/29 sales price 128,000 yen A digital amplifier equipped with a Tripath class T PWM amplifier IC. It beautifully expresses the sense of energy and description. Gain can also be switched on the back, and it is compatible with a wide range of input sources. The exterior is dull and there are scratches on the top of the front panel. Serial 090120022 (Tomonori Asaine)
Maintenance information: 2024.2.27 sound output confirmed
Accessories: power cord instruction manual
Main specifications: output 150W+150W (8Ω) 240W+240W (4Ω) W420 x H98 x D395 mm weight 13 kg
The price has been reduced. 2024/4/16 sales price 54,800 yen Marantz network player compatible with network audio, streaming, AirPlay2, Bluetooth, and USB memory, and is easy to use. PCM supports playback up to 192 kHz/24 bit, and DSD supports playback up to 5.6 MHz. The DAC is equipped with an ES9016K2M compatible with high-resolution sound source specifications similar to the ND8006. There is a slight feeling of use such as small scratches on the top plate. Serial BBL36190200699 (Mizushima Itsuro)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: remote control, instruction manual, power cable
Main specifications: DSD 2.8/5.6 MHz compatible PCM 192 kHz/24 bit Playback frequency range 2 Hz to 100 kHz W440 x H106 x D371 mm (without antenna) 6.6 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/3/12 sales price 28,000 yen ※2 shelves are missing. This model has an open form and is perfect for heat dissipation. This is a weight rack whose spacing can be changed with L-shaped brackets and screws. There are many dents and line marks on the exterior, top surface, and shelf boards, and dullness and a feeling of use can also be seen (Kobayashi Hitoshi)
Accessories: none
Main specifications: shelf board size W525 x D470 mm total load capacity approx. 250 kg W626 x D582 x H1122 mm 64 kg
RCA output terminal cap Due to its completely non-magnetic structure, when inserted into the RCA output terminal, it exhibits a high damping effect, and further improves sound image localization and signal-to-noise ratio. (FUJISAWA KOSHI)
Accessories: quartz resonator QR-8