Full maintenance from the unit, network, and exterior! A floor-type speaker full of furniture that uses plenty of walnut wood. A powerful Alnico magnet is used for the 38cm unit, and the synergistic effect with the cabinet makes the mid-high range fresh and dynamic sound. It is also attractive that the connection up to the high range is smooth (Kobayashi Hitoshi)
Maintenance information: 2024.4.17 Maintained (exterior repair/polishing/oil finish, saran net replacement, unit maintenance: low range side: edge replacement, magnetic circuit gap cleaning/center adjustment, high range side: magnetic circuit gap cleaning/center adjustment. Network maintenance: frequency characteristic check, ATT contact cleaning, terminal cleaning)
Accessories: saran net, key
Main specifications: 15 inch coaxial 2-way 3889 (AlcomaXLLL) efficiency 93 dB allowable input 150 W continuous input impedance 8 ohms frequency characteristics/28 Hz to 22 kHz internal volume 235 liters W705 x H1,110 x D480 mm 68 kg
The disposal price has been reduced. Member prices are not applicable. 2023/9/13 sales price 2,980,000 yen Maintained with attention to details such as drivers and wiring! The Georgian 4 is attractive for its elaborate horn configuration and beautiful furniture-like design. It is a model with a built-in crispy horn, a structure that creates a unique sound with a rich sense of scale, and the loud sound is truly an American masterpiece, but you can also feel a somewhat English-like sex appeal. *The attenuator has been maintained, but slight chipping occurs when turning due to deterioration of the original winding resistance (Oikawa Tetsuji)
Maintenance information: 2023.9.13 Maintained (828HF disassembly and maintenance: separation from magnetic circuit and diaphragm, magnetic circuit diaphragm maintenance: cleaning of the magnetic circuit, rustproof vibration system, round out, stop noise, T350 disassembly and maintenance: separation from the magnetic circuit and diaphragm, sound pressure difference adjustment: stop noise due to resonance sound generation, elimination of sound pressure drop due to rear sound leakage. Confirm that there are no modifications inside the housing. Remove rust from screws on screw-type terminals, pickle, and polish and clean the receiving side. ATT (x4) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: none
Main specifications: 4-way 15WK, 828HF, T350, X336 (300/3500) approx. W860 x D660 x H1,350 mm approx. 90 kg
Full maintenance, from replacing deteriorated parts to re-caulking each jack and socket! The original Model 7 has arrived. You can enjoy a glossy mid to high range sound with a high sense of transparency and a thick, exquisite balance. It's a model that has been over half a century since it went on sale for analog fans, but it's still one they admire. The lustrous, indescribable tone is an appeal that cannot be enjoyed on modern devices. There is a feeling of use due to appearance, dullness, small scratches, etc. Serial No. 21199 (Kobayashi Hitoshi)
Maintenance information: 2024.4.17 maintenance completed (balance volume slide, front lamp replacement, high pressure selenium diode addition, RCA jack and vacuum tube socket re-caulking repair. AC 100 to 117 V operation checked) 2022.7.15 maintenance (V5 socket pin replacement, operation check) 2022.2.11 maintenance (main volume and balance volume disassembly cleaning repair, subchassis rubber pad replacement, vacuum tube 12AX7 replacement/vacuum tube socket and RCA jack re-caulking repair. Operation check with AC 100 to 117 V) 2019.3.20 maintained (main volume replacement, balance volume disassembly, cleaning repair, low pressure selenium replacement, high pressure selenium diode addition, block capacitor 50 μF, electrolytic capacitor addition/replacement, oil capacitor 0.01 μF, etc. replacement, front lamp original replacement, input ground reinforcement repair, vacuum tube socket and RCA jack caulking repair, operation check)
Accessories: copy of instruction manual
Main specifications: tubular control amplifier, vacuum tube, ECC83/12AX7, 3-stage NF equalizer, NF type step switching control, W453 x H185 x D267 mm, weight 7.5 kg
The company's best integrated amplifier designed by generously pouring the technical power of the Si 3000. The design, such as dual mono construction, the shortest signal path, and the chassis created by making full use of alloy technology, is also a masterpiece that gives off its own unique personality. The driving power is excellent in the smooth mid-high range with a high sense of SN, and in the mid to low range with a high sense of sound pressure. The highest amount of information as a premain amplifier is attractive. There are small scratches on the exterior. Serial Y 2008 (Yonejima Satoshi)
Maintenance information: 2024.4.17 Maintained (SP knob removal screw correction and cleaning. Cord clamp misalignment fix screw misalignment fix Internal inspection, cleaning, remote control, light reception check. Bias and offset checks. (Voice check for each input/output)
Accessories: remote control, instruction manual, power cord
Main Specifications: Output: 175W+175W (8Ω) Input Terminals: RCA LINE x 5 (Caldas Rhodium Plating), XLR LINE x 1 (No. 2 HOT) Output Terminal: RCA x 2 Frequency Characteristics: 10Hz - 35kHz
W450×H170×D480mm 27kg
Maintained! Comes with stand (DK-8000). A model that has improved the network box of the Diaton 50th anniversary model DS-8000. I am overwhelmed by the clear, detailed treble from Pure Boron and the thick mid-low range compared to the 2S-305 broadcast monitor. Also, the quick start-up sound, which is unimaginable from its size, is excellent. There is a feeling of use in appearance, dullness, light scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 2022.10.21 maintained (exterior stand network exterior cleaning/large scratch filler repair/line scratch simple touch up (repair marks remain) saran net stain/frame cleaning mid-edge softening treatment unit detachable one-sided tweeter disassembly and disconnection repair)
Accessories: saran net
Main specifications: 3 way, 3 speakers, bass reflex system, floor type, anti-magnetic type, 5 ohm 35 Hz to 40,000 Hz 93 db/w/m main unit W500 x H870 x D442 mm network box W370 x H130 x D287 mm weight body 58 kg, network 8 kg
The deteriorated vacuum tubes etc. were replaced in 2023 and full maintenance has been completed! The vintage MC30 is still loved today, half a century later. The sharp high range and thick low to mid range sound are nothing short of wonderful. Since the left and right sides come out clearly without interference, you can feel a better sense of localization than a stereo machine. The good separation unique to mono amplifiers stands out, and it can play everything from jazz to classical music well (Murakoshi Yoichi)
Maintenance information: 2023.6.10 maintained (vacuum tube socket re-caulking repair, vacuum tube 12AX7 replacement, selenium countermeasure diode addition, 2W and 1/2W resistor replacement, HUM ADJ. readjustment/RCA jack re-caulking repair, operation check (measured at 25-38W SP:8Ω with rated output AC100-117 V).)
2012.6.12 Maintained (Capacitor Exchange/Mallory x 2, Sprag x 2, Europe x 2, Black Beauty x 10, Cornell x 2, Vacuum Tube, Partially Replaced with Good, Used, Silicon Rectifier, Vacuum Tube Pin, Rust Polishing and Socket Electrode Sack, Bolum, Sliding Surface Cleaning, RCA Pin Jack Cleaning, Each Voltage, Operation Inspection)
Accessories: none
Main specifications: rated output 30W, input sensitivity 0.5V vacuum tubes 6L6GC x 2, 5U4 x 1, 12AX7 x 2, 12BH7 x 1, 12AU7 x 1, W356 x H203 x D203 mm, weight 15.8 kg
Maintained! Genuine Electri A stainless steel chassis version of the 2nd generation reprinted model. It is a model that stands out for its good SNR feel and improved fine particle feel, etc., and its depth of pocket that is compatible with the latest sources is attractive. The heavy, vintage look is also wonderful. There are small transformer scratches on the exterior and many disappearing characters on the back. Serial JE10260 (Yonejima Satoshi)
Maintenance information: 2024.4.17 Maintained (The remodeled part has been restored to a state close to its original state. Since the electrolytic condenser liquid leak replacement shield case is out of stock, the additional guide pin was damaged, so create and paste a sticker with the missing letter in the hakama replacement character. Output audio check)
Accessories: No accessories
Main specifications: 6550 push-pull input 2 systems (XLR/RCA) rated output 75W+75W (4/8/16Ω) mono 150W (2/4/8Ω) W406 x H190 x D305 mm 30.5 kg
Maintained! The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its rich sound. The extrusion is strong and goes great with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. There are scratches, dullness, and discoloration in places (Kojima Yosuke)
Maintenance information: 2024.4.18 Maintained (1 power transistor, 1 driver transistor replaced, other bias transistors replaced, 14 in-board transistors replaced, 26 capacitors replaced, gain VOL both channels replaced. Mode switch SW dismantling and cleaning, meter lamp check, display lamp replacement. Caulk and clean each connector. (Pattern re-soldered, DC offset, bias adjusted)
Accessories: power cable
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
The price has been drastically reduced. 2024/4/10 sales price 450,000 yen The output tube has been replaced with a GE 6550! Genuine Electri A stainless steel chassis version of the 2nd generation reprinted model. It is a model that stands out for its good SNR feel and improved fine particle feel, etc., and its depth of pocket that is compatible with the latest sources is attractive. The heavy, vintage look is also wonderful. The hood is missing, there are many transformer paint peeling repair marks on the exterior, and the letters on the back have disappeared. Serial E10122 (Murakoshi Yoichi)
Maintenance information: 2017.10.18 Maintained (SW/VR disassembly contacts repolished, oxidized/vulcanized grease coated. Replace all 9P socket pins Voltage check for each part, check input/output waveforms, load test (at 1kHz, 8Ω load: 75W x 2) sound output test)
Accessories: instruction manual (copy)
Main specifications: 6550 push-pull input 2 systems (XLR/RCA) rated output 75W+75W (4/8/16Ω) mono 150W (2/4/8Ω) W406 x H190 x D305 mm 30.5 kg
※It has a cigarette smell, so it's cheap. This is Series 2 with dual outputs. It is a famous machine that achieves both a mild and highly textured mid to high range while having an unquestionably high amount of information. The high level of musicality that never becomes stiff due to its moderate temperature is also attractive. The exterior has scratches, stroke marks, and dullness. Serial R1256, S1256 (Fujisawa Yukishi)
Maintenance information: 2024.4.13 operation confirmed
Accessories: remote control, power cord, connection cord, brand new solbutton
Main specifications: full balance circuit input: XLR x 5/bypass XLR x 1 preamp part: W445 x H80 x D152.5 mm 11 kg power supply part: W445 x H38 x D122 mm 3 kg
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
The disposal price has been reduced. 2024/3/31 sales price 378,000 yen equipped with a long arm RMG309i for SPU-G shells! The dust cover will be replaced with a new one in 2022. You can enjoy the fluffy feeling unique to Torrens belt drives, and the afterglow of the sound fading away. You can enjoy the rich sound of the SPU, which is firmly scraped out from the depths of the sound groove. The phono cable is made by Canale, and the manufacturer of the armrest is unknown. As for the exterior, there is a slight feeling of use, dullness, etc. on the arms and armrests. Serial 12396 (Murakoshi Yoichi)
Maintenance information: 2022.2.13 maintenance (new dust cover created)
Main specifications: TD-521 belt drive floating system compatible with 33/45/78 main body W550 x H180 x D410 mm 15 kg RMG309 dynamic balance type needle pressure 0 to 7 g total length 408 mm effective length 320 mm overhang 11 mm
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
The first stage is all 4 PASVANE WE310A! This is Sun Valley's Western 91 300B single amp. Anyway, it's an amplifier that clearly expresses even the afterglow, and it has enough power. Although it has an output of 8W+8W, this model is extremely practical and of high quality. It is a power amplifier with a balanced, glossy tone with no excesses or deficiencies from low to high frequencies. There is a scratch on the back of the exterior. Serial 63113 (Yonejima Satoshi)
Maintenance information: 2021.6.13 manufacturer maintained (all metal fittings on the 310A socket have been increased and tightened, looseness of vacuum tube pins and socket fittings fixed) 2020.8.7 manufacturer maintained (as preventive maintenance, hot bond treatment to prevent disconnection is performed on the 310 grid cap solder part, and residual noise, gain, frequency characteristics, and voltage of each part are measured to confirm that there are no abnormalities)
Accessories: power cable
Main specifications: output 8W+8W vacuum tube 300B ✕ 2 (Elehamo) 310A x 4 (PSVANE) 5R4GY ✕ 1 (RCA) W400 x H210 x D300 mm weight 23 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/4/2 sales price 250,000 yen ※We have newly created head amplifier modules ✕ 2, Phono equalizer modules x 2, and flat modules x 2. Maintained! This is a control amplifier from Sony's high-end brand, the Esprit series. Straight Sony sound with a sense of speed similar to the TA-E900. I want to use the look and sound in combination with the company's Power TA-N902. The exterior has small scratches and is dull. Serial 200499 (Takasaki Atsushi)
Maintenance information: 2023.4.2 Maintained (2 flat modules replaced. Check the input/output waveform, check the left and right balance, and connect a power amplifier to perform a comprehensive operation test.)
2023.1.5 Maintained (Phono equalizer module x 2 replaced. Check the input/output waveform, check the left and right balance, and connect a power amplifier to perform a comprehensive operation test.)
2022.8.31 Maintained (head amplifier module ✕ 2, capacitor, semi-fixed resistor, relay, LED, lamp, Capcom, power cord replacement. All SW, VR disassembly and cleaning. Re-solder the deteriorated part of the solder surface of the board. Check the input/output waveform, check the left and right balance, and perform a comprehensive operation test by connecting a power amplifier.)
Accessories: copy of instruction manual
Main specifications: 2 phono inputs, 5 line inputs, 2 pre-out systems, W480 x H105 x D465 mm, 12.5 kg
※It has a cigarette smell, so it's cheap. An acoustic reality digital mono power amplifier known to those in the know. It has incredible high power from the start, and it makes speakers that are difficult to sound loud. Please enjoy the detailed and delicate sound that can only be enjoyed with this one. There are threads and line marks on the exterior (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (power display LED reinstalled, input changeover switch replaced, abrasive removed. I checked the output sound. *This model has a balanced output configuration. The negative side of the speaker terminal is not ground (sound is also produced on the negative side), please do not share it or connect it to GND.)
Accessories: power cable
Main specifications: 600W+600W (8Ω) W215 x H70 x 370 mm weight 3.4 kg/unit
The disposal price has been reduced. Member prices are not applicable. 2023/5/13 sales price 250,000 yen*The main volume, BASS, and TREBLE knob textures are different from the original. Internal parts have been thoroughly reviewed and maintenance has been carried out! This is a control amplifier from Sony's high-end brand, the Esprit series. Straight sound with a sense of speed similar to the TA-E900. The outline is clear and the sound image is drawn clearly. It is a vintage speaker and is especially recommended for jazz and rock fans. On the exterior, in addition to dullness and small scratches, there is a feeling of use, such as sticker marks on the top plate. Serial 200616 (Hiroki Aso)
Maintenance information: 2023.3.4 maintained (running test by refining the I/O board and screw parts) 2022.10.1 maintained (condenser semi-fixed resistance relay LED lamp IC spark killer Capricorn washer replacement implementation all SW VR disassembly cleaning board solder surface re-solder input/output waveform confirmation and left and right balance confirmation comprehensive operation test)
Accessories: copy of instruction manual
Main specifications: 2 PHONO inputs, 5 line inputs, 2 pre-out systems, W480 x H105 x D465 mm, 12.5 kg
The price has been reduced. 2024/4/16 Sales price 198,000 yen Edge softening treatment, etc. Maintenance completed! Comes with a 7.5 kg DK-2000Z stand dedicated to the DK-2000Z class weight! The DS-2000Z thoroughly sought realistic sound. The sound quality is beautiful and glittering, conveying even the feeling of air with sound. Please try the high resolution sound source. There is a feeling of use due to appearance, dullness, light scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 204.4.16 maintenance completed (exterior veneer float repair/cleaning, saran net replacement, woofer edge softening treatment)
Accessories: instruction manual, saran net
Main specifications: 3-way sealed system, bookshelf type speaker impedance 6 ohms playback frequency band 27 Hz to 80000 Hz output sound pressure level 90 dB maximum input 180 W dimensions W380 x H725 x D315 mm (356 mm with net) weight 37 kg stand dimensions W380 x H170 x D315 mm weight 27.5 kg
The disposal price has been reduced (member prices are not applicable). 2024/3/31 sales price 298,000 yen Maintained in 2014. It is a highly regarded CD transport with a high degree of perfection. The sound is neither too thick nor too thin, and has both sharpness and precision, a sound unique to Levinson during the heyday of CDs. While the sound quality is clear and fresh, it is compatible with a wide range of music genres with a rich, glossy tone. There are line scratches and threads on the exterior (Mizusaki Ryo)
Maintenance information: Maintained by Harman International on 2014.8.5 (CD clamper fixed, 11 deteriorated capacitors replaced, various parts adjusted, operation checked)
Accessories: remote control, instruction manual, power cord, transport lock
Main specifications: CD dedicated transport, 4 digital output systems, balance/BNC/RCA/ST link, W400 x H98 x D364 mm, 9.3 kg
Maintained in January 2024! It is a Harves speaker with increased appeal, such as the richness of the sound typical of an HL MONITOR. The Harves-like sound, which is characterized by a relaxed sound in addition to the mid-range density unique to those made in England, is attractive. Exterior maintenance has been carried out on the exterior, but in addition to scattering repair marks, there is a feeling of use over time, such as undulations on the woofer edge. *Saran net is not included. Serial 3349A 3349B (Tomonori Asaine)
Maintenance information: 2024.1.12 Maintained (exterior repair stain tinted front baffle repair polishing paint rear baffle cleaning
Woofer edge repair, protective agent application (with undulations), terminal replacement unit, detachable tweeter, corrosion, disconnection repair, diaphragm, dome coat treatment, 1 voice coil, bobbin deformation correction)
Accessories: none
Main specifications: 2 way 2 speakers, 22.5 cm cone woofer/2.5 cm soft dome tweeter impedance 8 Ω crossover 2,000 Hz sound pressure level 87 dB, W325 x H640 x D330 mm, 13.5 kg
The price has been drastically reduced! 2024/4/14 sales price 198,000 yen This model took the configuration of the flagship 7S1. The quality of the sound has improved compared to the predecessor, and in particular, the thickness of the sound has increased from low to medium, making it a well-balanced sound. The clear and clean spatial expression and smooth, gentle mid-high sound are attractive. There is a scratch on the top plate. Serial 20011208001208 (Fujisawa Yukishi)
Maintenance information: 2024.4.14 Operation confirmed
Accessories: remote control, instruction manual, power cord, connection cord
Main specifications: original mechanical module SACDM-1 1 bit DSD SEIKO NPC SM5866AS D/A converter with external clock terminal W440 x H127 x D413 mm 16.5 kg
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
Scarce! Altec's variable frequency mono channel divider! Deteriorated parts, including 10 deteriorated capacitors, have been replaced! The frequency can be changed by opening the front panel, and it is compatible with crossovers from 80 Hz to a maximum of 10,000 Hz, so a very wide range of settings can be made. It features a clear tone typical of Altec, and is a must-see for multi-system users using the company's amplifiers. The input/output is a lug type only, so please make your own RCA cables, etc. (SASAKI Shota)
Maintenance information: 2024.4.18 Maintained (neon tube lamp replacement, each C and R check. Replace power filter C and coupling C. ICOPAMP pin broken replacement. Front switch cleaning operation check)
Accessories: none
Main specifications: 2-way channel divider compatible with 120V specification crossover frequencies 80 Hz, 150 Hz, 250 Hz, 500 Hz, 800 Hz, 1,000 Hz, 1,500 Hz, 2,500 Hz, 5,000 Hz, 8,000 Hz, 10,000 Hz, W485 x H45 x D185 mm 2.5 kg
The disposal price has been reduced. Member prices are not applicable. 2024/4/8 sales price 198,000 yen This is a 2-inch compression driver that is also installed in the company's studio monitor CD-3820. Since the mounting position is common with the JBL 2-inch driver, it is a driver that can be enjoyed not only between GAUSS units, but also with JBL units. There is something like a white stain on the diaphragm (Oikawa Tetsuji)
Maintenance information: 2024.4.8 operation confirmed
Accessories: none
Main specifications: 2 inch compression driver playback frequency band 600 Hz to 13 kHz impedance 8 ohms diameter 178 x D 145 mm 13.1 kg
The disposal price has been reduced! Member prices are not applicable. 2024/4/12 sales price 188,000 yen The successor to the company's hit model Silver8 debuted at Hi-Fi. The color is HGBK (high gloss black) with a sense of luxury. The low range, which is easy to handle yet has a sense of volume, and the clear mid-high range with a wide range are attractive. There are scratches and scratches on the exterior. Serial 700247, 700247 (Fujisawa Yukishi)
Maintenance Information: 2024.4.12 Operation confirmed
Accessories: instruction manual, spikes
Main specifications: 3-way bass reflex type crossover frequency 570Hz,3.5kHz impedance 8Ω allowable input 200W efficiency 90dB size W185 x H1000xD300 mm W252 x H1034 x D367 mm (base foot included) weight 20.0 kg
The price has been reduced. 2024/4/16 Sales price 118,000 yen Manufacturer maintained! Marantz pre-main made as an amplifier compatible with super audio. The sound, which makes you feel more relaxed and warm than recent models from the company, which have sharp looks, is attractive. The phono is also MM/MC compatible, so there are no omissions. Dullness, there is a small scratch on the top plate (Sasaki Shota)
Maintenance information: 2024.4.16 manufacturer maintained (SP relay defect replacement, front VR main relay nuclear circuit Iida defect correction implementation, other operation inspections)
Accessories: manual, power cable, remote control
Main specifications: 100W+100W (8Ω) Playback frequency band: 5Hz to 100kHz Analog input: 7 systems Analog output: 2 systems Dimensions W458 x H166 x D464 mm Weight 23.0 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/4/13 sales price 128,000 yen ※The PHONO board is for MC only (MM cannot be used). Maintained! It has an elegant and glossy tone, and although combinations with 405 are common, 606 etc. are also a good match. It has the natural texture of the acoustic sauce and the smooth tone that feels good against the skin. There are small scratches and paint peeling on the right side. Serial 24151 (Takasaki Atsushi)
Maintenance information: 2024.4.12 maintenance (main board ground point screw reprocessing, operation check) 2024.1.17 maintenance (replacement of coupling C, bypass C, etc. in each board, AC SW spark killer C replacement, INPUT switching analog SW through hole pattern re-soldering, power SW internal contact polishing ~ operation check)
2020.6.13 Maintained (balance VR, SW disassembly cleaning. Attach 1 kΩ resistors to both the left and right sides of the flat board. Replaced due to faulty IC. All flat and mother boards have been soldered again. (Check the input/output waveform, check the left and right balance, and perform a comprehensive operation test by connecting the power amplifier to confirm normal operation.)
Accessories: power cord, copy of manual
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321 x H103 x D203 mm, 4.0 kg
The disposal price has been reduced. Member prices are not applicable. 2024/4/11 sales price 158,000 yen Maintained. with cabinet! Macintosh transistor AM/FM tuner. You can enjoy the deep, chiseled sound typical of McKinn even with a tuner. Small scratches and dullness can be seen. (GOTO Daiki)
Maintenance information: 2024.4.11 Maintained (poor contact with tuning encoder VOL → cleaning, other checks. (Reinstall the pan lock.)
Accessories: copy of instruction manual
Main specifications: stereo compatible digital display FM/AM tuner W406 x H138 x D330 mm
※It has a slight tobacco smell, so it is inexpensive. The premain uses an innovative Class D amplifier equipped with a “Direct Power FET” that realizes an extremely simple circuit configuration. Equipped with a 384 kHz/32 bit compatible DAC “SABRE32 Ultra DAC ES9016” with high-resolution ESS technology that is compatible with DSD 11.2 MHz playback, the clear and high S/N is attractive with a fully balanced circuit configuration. There are line scratches and dirt on the exterior. Serial JXEVOLVA000554JP (Fujisawa Yukishi)
Maintenance information: 2024.4.18 Maintained (LED replacement solder correction connectors, flexible reinstallation, wiring restyling. (The interior and exterior of each input/output sound check have been cleaned.)
Accessories: remote control, power cable
Main specifications: rated output 90W+90W W435 x H141.5 x D370 mm 18.3 kg
Maintained. Battery operated MC head amplifier. The modular type allows you to enjoy analog playback like the company's ML series. It has the sharpness and dynamic sound unique to being battery-powered, and the combination with the old SPU is particularly exquisite. There are scratches and scratches on the exterior. Serial 1232 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (there is a liquid leak mark on the battery holder. (It was cleaned and repaired because it was not available.)
Accessories: No accessories
Main specifications: 8 mV (maximum), output terminal with battery checker, 250 mV (maximum), frequency band 20 to 50,000 Hz, W220xH45xD100mm, 0.7 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/4/9 sales price 138,000 yen ※It is cheap because the condition is not good. Next-generation model of the L-550, a famous pure Class A amplifier that has been maintained by the manufacturer (*PHONO1 cannot be used due to a broken equalizer board). The very smooth, deafening warm color sound perfectly matches the delicate sound quality of pure A grade. It also has a reputation for analog sound, and thick sound quality can be obtained with both MM/MC. There is a feeling of use due to appearance, dullness, abrasions, scratches, paint deterioration, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.9 manufacturer maintenance completed (equalizer selector switch disassembly cleaning, correction due to broken equalizer board, other contact cleaning, general adjustment*PHONO1 cannot be used due to broken equalizer board)
Accessories: copy of instruction manual
Main specifications: pure A grade 50W+50W (8Ω) PHONO (MM/MC) PHONO/CD straight circuit system W453 x H174 x D470 mm weight 20 kg
The price has been drastically reduced. 2024/4/15 sales price 118,000 yen Maintenance is being carried out in 2020. 60Hz specification. A record player equipped with Ortofon's short arm RS-212 on the TD160. Only the turntable and arm mounts have a floating structure. It is an attractive player with a sharp sound and sound quality typical of Torrens. The springs on the dust cover hinge have deteriorated. There is damage such as scuffs and scratches on the cabinet dust cover. Serial 422455 (Murakoshi Yoichi)
Maintenance information: 2020.10.10 Maintenance completed (arms, arm bases, etc. are cleaned because rubber adhesives adhere to a wide area, etc., removed because the cushion spring is fixed with foreign matter, sub-board rubber adhesive cleaning, motor connection terminals (faston chips) are broken and unstable, arm elevation cannot be disassembled or adjusted, so current status (descent is slightly fast), arm operation, voice check)
Accessories: sub weight, AC adapter
Main specifications: one-step belt drive system, 16-pole synchronous motor, zinc alloy turntable (diameter 30 cm, weight 3.2 kg), W440 x H165 x D350 mm, 11.0 kg
The price has been reduced. 2024/4/8 sales price 99,800 yen B&W bookshelf speaker. Each one has good sound granularity and a clean tone, and is compatible with a wide range of genres and sources. It is an attractive, practical speaker with medium to high range quality comparable to advanced models. There is a slight feeling of use, such as light rubbing on the front baffle. Serial 0018723 0018724 (Mizushima Itsuro)
Maintenance information: 2024.4.8 operation confirmed
Accessories: instruction manual, saran net, jumper plate
Main specifications: 2-way bass reflex type bookshelf speaker playback frequency band 45 Hz to 50 kHz W200 x H340 x D280 mm 8.9 kg
The price has been drastically reduced. 2023/12/29 sales price 99,800 yen Maintenance completed! The design full of oldies is attractive, and Newcam's mono mixer premain for PA. 6L6 is used as the output tube. Channel 1 is compatible with LINE, PHONO, and MIC, and channels 2 to 4 are compatible with microphones. The volume for each channel is around 12 o'clock, and MASTER is used for volume adjustment. There is a feeling of use such as small scratches and paint deterioration appropriate to the exterior model year (Kobayashi Hitoshi)
Maintenance information: 2023.12.12 maintenance (master volume disassembly, cleaning repair, MIC input transformer, etc. contact repair, left side front lamp off, 12AX7, 150 μF electrolytic capacitor replacement. Vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 41 to 61 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Main specifications: 6L6 push-pull 60W mono LINE, 1 PHONO system each, MIC4 system W440 x H190 x D350 mm 16.5 kg