Scarce! Altec's variable frequency mono channel divider! Deteriorated parts, including 10 deteriorated capacitors, have been replaced! The frequency can be changed by opening the front panel, and it is compatible with crossovers from 80 Hz to a maximum of 10,000 Hz, so a very wide range of settings can be made. It features a clear tone typical of Altec, and is a must-see for multi-system users using the company's amplifiers. The input/output is a lug type only, so please make your own RCA cables, etc. (SASAKI Shota)
Maintenance information: 2024.4.18 Maintained (neon tube lamp replacement, each C and R check. Replace power filter C and coupling C. ICOPAMP pin broken replacement. Front switch cleaning operation check)
Accessories: none
Main specifications: 2-way channel divider compatible with 120V specification crossover frequencies 80 Hz, 150 Hz, 250 Hz, 500 Hz, 800 Hz, 1,000 Hz, 1,500 Hz, 2,500 Hz, 5,000 Hz, 8,000 Hz, 10,000 Hz, W485 x H45 x D185 mm 2.5 kg
The first stage is all 4 PASVANE WE310A! This is Sun Valley's Western 91 300B single amp. Anyway, it's an amplifier that clearly expresses even the afterglow, and it has enough power. Although it has an output of 8W+8W, this model is extremely practical and of high quality. It is a power amplifier with a balanced, glossy tone with no excesses or deficiencies from low to high frequencies. There is a scratch on the back of the exterior. Serial 63113 (Yonejima Satoshi)
Maintenance information: 2021.6.13 manufacturer maintained (all metal fittings on the 310A socket have been increased and tightened, looseness of vacuum tube pins and socket fittings fixed) 2020.8.7 manufacturer maintained (as preventive maintenance, hot bond treatment to prevent disconnection is performed on the 310 grid cap solder part, and residual noise, gain, frequency characteristics, and voltage of each part are measured to confirm that there are no abnormalities)
Accessories: power cable
Main specifications: output 8W+8W vacuum tube 300B ✕ 2 (Elehamo) 310A x 4 (PSVANE) 5R4GY ✕ 1 (RCA) W400 x H210 x D300 mm weight 23 kg
An Audio-Technica interconnect cable that uses a 1.5m pair of RCA cables and PCCC2 heavy coaxial cables. You can feel the dullness all over (Murakoshi Yoichi)
Maintenance information: 2024.4.17 continuity confirmed
Accessories: none
The deteriorated vacuum tubes etc. were replaced in 2023 and full maintenance has been completed! The vintage MC30 is still loved today, half a century later. The sharp high range and thick low to mid range sound are nothing short of wonderful. Since the left and right sides come out clearly without interference, you can feel a better sense of localization than a stereo machine. The good separation unique to mono amplifiers stands out, and it can play everything from jazz to classical music well (Murakoshi Yoichi)
Maintenance information: 2023.6.10 maintained (vacuum tube socket re-caulking repair, vacuum tube 12AX7 replacement, selenium countermeasure diode addition, 2W and 1/2W resistor replacement, HUM ADJ. readjustment/RCA jack re-caulking repair, operation check (measured at 25-38W SP:8Ω with rated output AC100-117 V).)
2012.6.12 Maintained (Capacitor Exchange/Mallory x 2, Sprag x 2, Europe x 2, Black Beauty x 10, Cornell x 2, Vacuum Tube, Partially Replaced with Good, Used, Silicon Rectifier, Vacuum Tube Pin, Rust Polishing and Socket Electrode Sack, Bolum, Sliding Surface Cleaning, RCA Pin Jack Cleaning, Each Voltage, Operation Inspection)
Accessories: none
Main specifications: rated output 30W, input sensitivity 0.5V vacuum tubes 6L6GC x 2, 5U4 x 1, 12AX7 x 2, 12BH7 x 1, 12AU7 x 1, W356 x H203 x D203 mm, weight 15.8 kg
A line selector that can be easily switched with an RCA connection. It can also be used for 4 input systems, 1 output system or 1 reverse input system, and 4 output systems, making it convenient to switch between multiple amplifiers and sources. There is a feeling of use on the exterior, such as small scratches and dullness (Asaine Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
RCA cable 1.0 m pair with 24K gold-plated turbine plug and split center pin specification, 2-core structure, sheath resistant to aging, and Duraflex jacket. The exterior has a feeling of use and dullness (Tomoho Asae)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
A clear and powerful top model in the group that uses a 1.0 m pair of RCA cables and PSC conductors. Excellent cost performance There is dullness in the plug (Tomoho Asaine)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
RCA cable uses 1.2 m pair of high-purity oxygen-free copper with super annealing treatment, 2-core shielded high-density braided structure, and high-grade gold-plated plugs with precision machining. The sound quality is stable, natural, and has no sense of emphasis. There is a feeling of use such as dullness on the exterior (Asae Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
RCA cable 1.5m pair rhodium plated plug accuphase genuine OFC series cable looks like a high-purity OFC Ritz cable with excellent corrosion resistance, and it sounds supple at the same time as extrusion in the mid to low range. The exterior has a feeling of use such as rubbing, dirt, and bending habits on the sheath (Asaine Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
Mark 3 model of the long-selling model “A2050 Series” with a 0.6 m pair of RCA cables. Ultrapure copper of 7N or higher was adopted for the first time in this class, and both transparency and range have been improved from the previous model, and this degree of perfection is excellent in this price range (Asaine Tomo)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
RCA cable 1.3 m pair Audio-Technica RCA cable Uses 24K gold-plated plugs and PCOCC conductors. The cable is soft, easy to handle, and easy to use. There is a feeling of use on the exterior such as dullness and small scratches (Asaine Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
Please upgrade to an RCA cable, 1.0 m pair, or Monster Cable standard cable from the original one. There is dullness etc. on the exterior (Tomonori Asae)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
Maintained! Quad control amplifier The famous machine 44 has been refreshed by changing the back terminal to an RCA specification that is easy to handle. It's a perfect balance between freshness and richness. When paired with speakers made in England, you can enjoy a calm, high-quality sound (Daiki Goto)
Maintenance information: 2024.4.17 maintained (internal all checks, B-filter capacitor deterioration, +- 18V drive Tr leak large, rectifier diode failure instability → replacement power SW spark killer broken → replacement. C and R checks within each board. *There is a sound leak at main volume 0. (Create 2 1.5m DIN5 cables)
Accessories: copy of instruction manual, power cable, connection cable
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321×H103×D203 mm
Maintained! Genuine Electri A stainless steel chassis version of the 2nd generation reprinted model. It is a model that stands out for its good SNR feel and improved fine particle feel, etc., and its depth of pocket that is compatible with the latest sources is attractive. The heavy, vintage look is also wonderful. There are small transformer scratches on the exterior and many disappearing characters on the back. Serial JE10260 (Yonejima Satoshi)
Maintenance information: 2024.4.17 Maintained (The remodeled part has been restored to a state close to its original state. Since the electrolytic condenser liquid leak replacement shield case is out of stock, the additional guide pin was damaged, so create and paste a sticker with the missing letter in the hakama replacement character. Output audio check)
Accessories: No accessories
Main specifications: 6550 push-pull input 2 systems (XLR/RCA) rated output 75W+75W (4/8/16Ω) mono 150W (2/4/8Ω) W406 x H190 x D305 mm 30.5 kg
The company's best integrated amplifier designed by generously pouring the technical power of the Si 3000. The design, such as dual mono construction, the shortest signal path, and the chassis created by making full use of alloy technology, is also a masterpiece that gives off its own unique personality. The driving power is excellent in the smooth mid-high range with a high sense of SN, and in the mid to low range with a high sense of sound pressure. The highest amount of information as a premain amplifier is attractive. There are small scratches on the exterior. Serial Y 2008 (Yonejima Satoshi)
Maintenance information: 2024.4.17 Maintained (SP knob removal screw correction and cleaning. Cord clamp misalignment fix screw misalignment fix Internal inspection, cleaning, remote control, light reception check. Bias and offset checks. (Voice check for each input/output)
Accessories: remote control, instruction manual, power cord
Main Specifications: Output: 175W+175W (8Ω) Input Terminals: RCA LINE x 5 (Caldas Rhodium Plating), XLR LINE x 1 (No. 2 HOT) Output Terminal: RCA x 2 Frequency Characteristics: 10Hz - 35kHz
W450×H170×D480mm 27kg
※It has a cigarette smell, so it's cheap. A rare Audiocraft RCA to XLR conversion converter has arrived. A useful item for converting an RCA pin cable into a balanced cable. The exterior has paint bald spots, dirt marks, etc. Serial 43217 (Yonejima Satoshi)
Maintenance information: 2024.4.17 operation confirmed
Accessories: none
Main specifications: W200×H75×D300mm 2.7 kg
Ishino Lab's control amplifier that uses a rectifier tube for the power supply unit. Although it is a small and long body, it is a car with excellent cost performance, such as separating the power supply part and installing an MC transformer compatible with a wide range of cartridges. The output is also equipped with RCA balance. The exterior is dull (Tamura Eiji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: instruction manual, power cable, connection cable
Main specifications: 2 phono systems, LINE1 system amplifier part: W250 x H75 x D230 mm weight 2.2 g power supply unit: W150 x H75 x D230 mm weight 2.8 kg
Full maintenance, from replacing deteriorated parts to re-caulking each jack and socket! The original Model 7 has arrived. You can enjoy a glossy mid to high range sound with a high sense of transparency and a thick, exquisite balance. It's a model that has been over half a century since it went on sale for analog fans, but it's still one they admire. The lustrous, indescribable tone is an appeal that cannot be enjoyed on modern devices. There is a feeling of use due to appearance, dullness, small scratches, etc. Serial No. 21199 (Kobayashi Hitoshi)
Maintenance information: 2024.4.17 maintenance completed (balance volume slide, front lamp replacement, high pressure selenium diode addition, RCA jack and vacuum tube socket re-caulking repair. AC 100 to 117 V operation checked) 2022.7.15 maintenance (V5 socket pin replacement, operation check) 2022.2.11 maintenance (main volume and balance volume disassembly cleaning repair, subchassis rubber pad replacement, vacuum tube 12AX7 replacement/vacuum tube socket and RCA jack re-caulking repair. Operation check with AC 100 to 117 V) 2019.3.20 maintained (main volume replacement, balance volume disassembly, cleaning repair, low pressure selenium replacement, high pressure selenium diode addition, block capacitor 50 μF, electrolytic capacitor addition/replacement, oil capacitor 0.01 μF, etc. replacement, front lamp original replacement, input ground reinforcement repair, vacuum tube socket and RCA jack caulking repair, operation check)
Accessories: copy of instruction manual
Main specifications: tubular control amplifier, vacuum tube, ECC83/12AX7, 3-stage NF equalizer, NF type step switching control, W453 x H185 x D267 mm, weight 7.5 kg
* No. 3 hot specification RCA-XLR conversion cable, 3.9 m pair, both end plugs are a standard BELDEN line cable that clearly shows the outline of Neutrik's sound yet has a firm thickness, especially in the mid to low range. The sheath printing disappears a lot (Kojima Yosuke)
Accessories: none
The price has been drastically reduced! 2023/4/16 sales price 138,000 yen genuine Rin Japan product. The Sneaky DSM with built-in network player function and 2ch amplifier has arrived. It has a smart design that eliminates anything superfluous, and can be operated with an iPod or the like. Of course, it also has an excellent external input function. There are no noticeable scratches on the exterior. Serial 1324171 (Fujisawa Yukishi)
Maintenance information: 2024.4.16 Operation confirmed (Ver. 4.104.518)
Accessories: remote control, power cord, original box
Main specifications: analog input: RCA1 system digital input: coaxial, 1 optical system, 3 HDMI output, 1 HDMI system*RCA has variable output and fixed output can be changed by setting Compatible files: FLAC, WAV, Apple Lossless, AIFF, MP3, WMA, AAC, OGG Compatible Bits: 16 to 24 bits 33W ✕ 4ch (4Ω) W350 ✕ H54.5 ✕ D215mm Weight 2.3 kg
RCA cable 0.5m pair REAN (Neutrik) RCA plug This is a standard BELDEN line cable that clearly outlines the sound while having a firm thickness, especially in the mid to low range (Fujisawa Yukishi)
Maintenance information: 2024.4.16 continuity confirmed
Accessories: No accessories
RCA cable 0.5m pair REAN (Neutrik) RCA plug This is a standard BELDEN line cable that clearly outlines the sound while having a firm thickness, especially in the mid to low range (Fujisawa Yukishi)
Maintenance information: 2024.4.16 continuity confirmed
Accessories: No accessories
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
※The Y lug on the ground cord on one side is missing. 24K gold plating is also applied to the electrode part and Y terminal of the 2.0m phono cable plug, so while ensuring durability, the sound stage also feels spacious. The cost performance is high! In addition to the appearance described above, there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: none
※It has a cigarette smell, so it's cheap. Compared to the 1.0 m pair of RCA cables, EQI6, OCC high-purity copper conductors, up to Equinox 5, the company's standard cable, which has a high level of clarity and creates a high-end oriented sound, is recommended as a first step towards luxury cables. There is a feeling of use due to appearance, dullness, friction, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.15 continuity confirmed
Accessories: none
※Inexpensive because of the cigarette smell. Balance cable, 0.5 m pair, NEUTRIK plug. Neumann RCA cable familiar from the prestigious German family. Recommended for those who listen to classical music on records. Since it is slender and soft, it is useful in a variety of situations. There is a feeling of use due to appearance, dullness, friction, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.15 continuity confirmed
Accessories: none
Maintenance was completed in 2015/11, such as replacing capacitors and replacing deteriorated parts. It is a famous machine with a velvet transformer, and you can enjoy rich sound with stable operation. The fresh, glossy tone in the mid to high range has a different appeal from the MC275. There is a feeling of use such as scratches and lettering disappearing on the chassis (Mizushima Itsuro)
Maintenance information: 2015.11.19 Maintained (EL.C12μF1 exchange/EL.C100μF 2 replacement, R2W 4 replacement, R1/2W 4, AC cord exchange/RCA jack caulking and polish repair/VT socket caulking repair*Other parts check (OIL.C has been unified to orange drop))
Accessories: Copy of instruction manual (English)
Main specifications: 0W+40W 6L6GCPP vacuum tube 6L6GC × 4 12AX7 × 3 12AU7x2 12BH7 × 2 frequency characteristics 16 to 40,000 Hz dimensions W400 × D265 × H195 mm weight 25 kg
※The plug has changed to WBT. RCA cable, 1.0 m pair, stress-free 6N conductor, has a narrower range than Acrolink models, so it makes a thick sound. Recommended for domestic systems from the 90s and up, the color has faded (Tetsuji Oikawa)
The price has been reduced! 2024/4/14 sales price 548,000 yen Manufacturer maintained! Equipped with an evolved VRDS-NEO (VMK-3.5-10). A 32-bit monaural DA converter with 4 circuits achieves overwhelming resolution and signal-to-noise ratio. It accurately reproduces not only detailed sound sources, but also very powerful sounds. Serial 30008 (Fujisawa Yukishi)
Maintenance information: 2024.2.27 manufacturer maintained (mechanical ASSY disassembled. cleaning. Lubrication clamper mechanism partial dismantling. Tweaks and corrections have been implemented. (Each part is cleaned, inspected, and adjusted)
Accessories: remote control, instruction manual, power cord
Main specifications: Playable disc/super audio CD, CD (CD-R/CD-RW compatible) output terminal 1 RCA/XLR output impedance RCA/47Ω XLR/100Ω frequency characteristics 5 Hz to 55,000 Hz S/N ratio 115 dB digital input RCA terminal/optical digital terminal/USB-B terminal 1 system each power consumption 27W W445 x H162 x D438 mm 28 kg
RCA cable 1.0m interconnect cable that uses hybrid conductors made of 5 materials, which Zonotone excels at. A powerful machine that combines the power of the company's high-end BlueSpilit cable with the sound field of Royal Spilit. There is a thin thread on the exterior (Yonejima Satoshi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: original box
Stereo mini jack to RCA male conversion cable 0.2 m has an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Stereo mini plug to RCA female conversion cable 0.2 m has an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Set of 2 RCA short pin plugs from the “Stereo” magazine appendix. By shorting unused input terminals, the circuit is stabilized and sound quality is improved (Asaine Tomo)
Accessories: none
The price has been drastically reduced. 2024/4/14 sale price 1,450,000 yen Mark Levinson dual mono preamp No. 526! This is an ESS 32-bit D/A converter compatible with 192 kHz/32 bits. Also, it is equipped with plenty of digital inputs such as 2 coaxial, 2 optical, AES/EBU, and USB, and reproduces compressed digital sources with high fidelity. It is impressive that it has a more glossy SN feel than No. 326S. The exterior has a scratch on the upper front corner, and a small scratch on the back of the remote control about the size of a pinky finger nail (Sasaki Shota)
Maintenance information: 2024.4.13 operation confirmed
Accessories: remote control, manual, power cable, screwdriver, original box
Main specifications: analog input terminals/XLR balance x 2 pairs, RCA unbalance x 3 pairs, phono input x 1 pair, digital input terminal/XLR balance x 1 pair, RCA coaxial x 2, optical (Toslink) x 1, USB-B (asynchronous) x 1 output terminal/XLR balance x 1 pair, RCA unbalance x 1 pair, headphones (6.3 mm phono) x 1 W438 x H102 x D457 mm 18.6 kg
Maintained! It is a model designed by US Marantz and manufactured in Japan. It develops an American sound with a dry air feel and strong push. The design is also a vintage control amplifier with a taste unique to the 70s. Externally, there are scratches and threads on the cabinet. *Some RCA terminals and inlets have been changed. Serial 7237 (Tamura Eiji)
Maintenance Information: 2024.4.13 Maintained (Mode selector stopper mechanism fixed. Electrolytic capacitors and film capacitors have been replaced. The speaker terminal (red and black type) has been processed and replaced. The end of RCA TAPE was replaced due to discoloration. Each input/output operation was checked.)
Accessories: power cable
Main specifications: Line input 5 systems, phono (MM), 2 systems, pre-out, 1 system, W391 x H146 x D222 mm, 7.3 kg
The price has been drastically reduced! 2024/4/13 sales price 128,000 yen Maintained! 800Hz/2 way specification This is the balanced input/output model of the F-15. It is one of the few channel dividers where you can enjoy multiple systems while retaining an analog feel. You can adjust the multi-system correctly with clean, clutter-free sound. There are scratches and scratches on the exterior. Serial K8Y452 (Fujisawa Yukishi)
Maintenance information: 2024.4.13 maintained (AC cord, push switch replacement, ATT disassembly cleaning, card edge contact cleaning, crossover characteristic check, interior and exterior cleaning)
Accessories: instruction manual
Main specifications: 2 way/3 way divider input/output RCA/XLR switching type frequency fixed by board W445 x H109 x D373 mm 9.1 kg
The price has been drastically reduced! 2024/4/13 sales price 348,000 yen ※ It is cheap because it is in poor condition such as deposits, scratches, tobacco smell, etc. A power amplifier that enables overwhelming spatial expression with a second-generation ultra-high speed switching power supply. First of all, I was surprised by the smooth, cored sound. The driving power is also excellent, and it has the ability to easily drive high-class speakers. The exterior is dull all over, and there are abrasions on the top plate and front (Yonejima Satoshi)
Maintenance information: 2024.4.13 operation confirmed
Accessories: connection cord, power cable
Main specifications: 150W+150W (8Ω) input/unbalance (RCA) 1 system/balanced (XLR) 1 system SP terminal/1 system main unit W445 x H97 x D335 mm power supply unit W445 x H97 x D319 mm body 13.5 kg power supply 13.7 kg
RCA cable, 0.5 m, pearitz coated OCC copper, has a relatively clean tone, and is a product made by Wireworld that is particular about sound quality while keeping costs down. (FUJISAWA KOSHI)
Maintenance information: 2024.4.12 continuity confirmed
Accessories: original box
RCA output terminal cap Due to its completely non-magnetic structure, when inserted into the RCA output terminal, it exhibits a high damping effect, and further improves sound image localization and signal-to-noise ratio. (FUJISAWA KOSHI)
Accessories: quartz resonator QR-8
Standard plug to RCA cable 2.0m used for transmission from a headphone output such as a deck to an RCA input such as an amplifier (Yoichi Murakoshi)
Maintenance information: 2024.4.12 continuity confirmed
Accessories: original box
The price has been drastically reduced. 2024/4/11 sales price 118,000 yen ※It's cheap because it doesn't have a hood. Maintained! Vacuum tube stereo power amplifier. The bright and fresh sound typical of DYNACO is attractive. This is an amplifier I want to play in combination with JBL, Altec, etc. The grill is missing, and there is a feeling of use due to aging (Daiki Goto)
Maintenance Information: 2024.4.11 Maintained (· Block Capacitor 30/20/20 μF Defect Replacement · Stereo/Mono Switch Defect Replacement · Shock Noise Improvement Measures → Spark Killer Addition · Vacuum Tube 7199 Noise Exchange · Mylar Capacitor 390pF Deterioration Replacement 2 · Resistors 1/2 W Deterioration Replacement · BIAS Readjustment · Vacuum Tube Socket and RCA Jack Caulking Repair. *Other operation checks have been performed (measured at 32 to 41 W SP: 8 Ω at rated output AC 100 to 117 V)
Accessories: instruction manual
Main specifications: rated output 35W+35W vacuum tube EL34 x 4 7199 x 2 GZ-34 x 1 W330 x H165 x D240 mm 12.5 kg
The price has been drastically reduced. 2024/4/10 sales price 450,000 yen The output tube has been replaced with a GE 6550! Genuine Electri A stainless steel chassis version of the 2nd generation reprinted model. It is a model that stands out for its good SNR feel and improved fine particle feel, etc., and its depth of pocket that is compatible with the latest sources is attractive. The heavy, vintage look is also wonderful. The hood is missing, there are many transformer paint peeling repair marks on the exterior, and the letters on the back have disappeared. Serial E10122 (Murakoshi Yoichi)
Maintenance information: 2017.10.18 Maintained (SW/VR disassembly contacts repolished, oxidized/vulcanized grease coated. Replace all 9P socket pins Voltage check for each part, check input/output waveforms, load test (at 1kHz, 8Ω load: 75W x 2) sound output test)
Accessories: instruction manual (copy)
Main specifications: 6550 push-pull input 2 systems (XLR/RCA) rated output 75W+75W (4/8/16Ω) mono 150W (2/4/8Ω) W406 x H190 x D305 mm 30.5 kg
The price has been drastically reduced. 2024/4/10 sales price 10,000 yen. Coaxial cable 0.9 m 75 ohm collet chuck plug From the shield notation, it seems that the cable is also made by ZAOLLA. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.8 continuity confirmed
Accessories: none
RCA cable, 1.0 m pair, 2-core shield structure, rhodium-plated plug suppresses sound dramatization and reproduces the individuality of the amplifier and player as it is. The plug shell is dull and discolored a lot, and the LR coloring is deteriorated and damaged, so it is inexpensive (Kojima Yosuke)
Accessories: none
The disposal price has been reduced! (Member prices are not applicable) 2024/4/8 sales price 198,000 yen Maintained! Macton tubular OTL stereo power amplifier. Eight 6RA3 triodes are used in parallel per channel to enhance load impedance adaptability, and it also features a structure with Macton's unique balanced NF applied. The sound unique to OTL is thick and has a high sense of energy, and the high driving power is also attractive. The appearance is oxidized and dull. Serial 40704 (Yonejima Satoshi)
Maintenance information: 2024.4.8 Maintained (power transformer primary side rewound repair by PSE inspection. 3 vacuum tube 6RA3 replacements Vacuum tube 6AQ8 replacement. Main volume disassembly cleaning repair. Vacuum tube socket and RCA jack caulk repair. Operation has also been checked with AC 100V (rated output 32W, SP:16Ω), please use speakers above 16Ω)
Accessories: No accessories
Main specifications: tubular low-load OTL stereo power amplifier 30W x 30W (8Ω) vacuum tube used: 6RA3 x 10/6RA8 x 2/12AX7 W370 ✕ H160 ✕ D270 mm 12 kg
An affordable Lax interconnect cable with attention to detail, such as each core structure that makes the hot and cold of the 1.0 m RCA cable transmission line the same, and a core wire wrapped in Japanese paper. It is characterized by its moderate thickness and good S/N. (YONEJIMA Satoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: No accessories
Parallel cable 1.4 m pair end RCA plug cable that distributes 2 RCA L and R If you've been looking for one, go ahead. In addition to the exterior and writing on the plug, there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: none
The disposal price has been reduced! (Member prices are not applicable) 2024/4/3 sales price 218,000 yen Maintenance has been completed. It is a hidden popular model as the successor to the C26. It is an amplifier from the golden age of McKinn that is highly popular with music fans, with a sound reminiscent of a rich, thick vacuum tube sound. It makes vintage speakers sound intense. The exterior has paint floats, rust spots, etc. Serial BV2290 (Tamura Eiji)
Maintenance information: 2024.4.3 maintained (input selector, other contact cleaning. Balancer volume contact cleaning. Electrolytic capacitor replacement. RCA terminal replacement. The power supply voltage was changed to 100V compatible. (Check the operation of each input/output)
Accessories: No accessories
Main specifications: input PHONO 1 · 2, AUX 1 · 2, TUNER, TAPE 1 · 2 W435 × H188 × D395 mm 11.8 kg