Maintained in 2023! Hammer tone BBC specification! Strobe platter included! This is a combination of GARRARD 301 and SME 3009S2, which has an attractive gripping, and gutsy sound. The high sensitivity short arm with high utility and the sound produced from the idler turntable is exhilarating and very comfortable. It is a record player system that allows you to experience the true essence of analog. Since the shaft on the back of the motor is long, an Audio-Technica insulator is included. *Currently, the pulley has a 60 Hz specification, but the strobe platter is for 50 Hz (Murakoshi Yoichi)
Maintenance information: 2023.8.15 maintenance (motor disassembly/check, lubrication, assembly. Main bearing disassembly, cleaning, oil injection, oil sealant application, assembly. Overall cleaning. idler cleaning Motor suspension spring rubber replacement. Transport plate fixing clip. Linguage distortion correction. Noise suppressor rebuild replacement. Mount rubber washer added. 50Hz pulley adjustment added. SME3009S2 cleaning. Mount grommet replacement Contact cleaning. (Running test)
Accessories: insulator (audio technica AT616)
Main specifications: 301: idler drive 33, 45, 78 rotations compatible 3009S2: short arm static balance type, total length 265 mm, overhang 15 mm, needle pressure (when 1 rider weight is attached) 1 memory 0.25 g step 0 g to maximum 2.5 g (when 2 rider weights are attached) 1 memory 0.5 step 0 g to maximum 5 g cartridge dead weight up to 28 g size W480 x D406 x H238 mm weight 12.5 kg
Maintained. A rare Fisher tube control amplifier. The 2 phono inputs are attractive. The high range is decent, but the round, rich, and powerful mid-range is unique to FISHER. The sound is light, bright and friendly. *Only CHANNEL A is valid for EQUALIZATION LP and 78 (Murakoshi Yoichi)
Maintenance information: 2024.4.17 maintenance (re-strengthening treatment for all selector knobs (*Please do not remove them as much as possible.) Volume disassembly grease up treatment for BASS, main volume disassembly, cleaning and repair (due to the structure, there are some gang errors and sound leaks when narrowed down to a minimum. (If you are concerned, only RIAA 1 and AUX1 can be adjusted with LEVEL SET on the top surface.) Electrolytic capacitor 1000 μF replacement, vacuum tube socket and RCA jack re-caulking repair. Operation check with AC 100 to 117 V) 2021.5.15 maintained (repair of poor contact with each part selector, etc., correction of lever deformation points, replacement of block capacitors 30/30/10/10 μF defects, vacuum tube sockets and RCA jack caulk repairs ※ Since the main volume is a special type with a loudness terminal, some gang errors will occur after 12:00. AUX1 and PHONO can be fine-tuned with the LEVEL SET on the top. *Other operation checks have been made (4 vacuum tube shield cases are missing)
Accessories: Service Manual (English)
Main specifications: Vacuum tube 12AX7, 12AT7, 6V4 using PHONO2 system Dimensions W390 x H120 x D210 mm 6.6 kg
Maintained by the manufacturer! 4th generation of the DENON 2000 series. It is an amplifier that can be enjoyed regardless of the genre of music, with its plump, loud mid and low frequencies, and a pleasant, sharp tone. The exterior has dents in the upper right corner of the front, light line scratches in the lower left corner, and dullness throughout (Kanai Hidetsugu)
Maintenance information: 2024.4/18 manufacturer maintenance (disassembling the switch, polishing the contact, grease coating, idling adjustment, operation test)
Accessories: instruction manual, power cord
Main specifications: High-rigidity 6-block, separated chassis, power amplifier, direct input, bi-wiring compatible, 80W+80W, W434 x H180 x D478 mm, 23.5 kg
The strobe light is missing. Clear audio stroboscope There is a groove, and rotation can be checked while the cartridge is placed on it. Rotations up to 78 rotations can be confirmed at both 50 Hz and 60 Hz (Murakoshi Yoichi)
Accessories: none
Stroboscope included with Oyaide's BR-12 turntable seat. Measurement of up to 78 revolutions is possible. It comes with an overhang gauge. The large size and ease of adjustment are attractive (Murakoshi Yoichi)
Accessories: none
※ Sub weight is missing. A long-selling player that Technics is proud of. It boasts a simple design that is easy to use, stable operation, and durability. Clear contours, high earthquake resistance, highly accurate tone arms, etc., all of these are attractive cars with a degree of perfection that exceeds the price. Exterior, slight small scratches, abrasions, etc. can be seen (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: dust cover
Main specifications: Quartz control direct drive system speed 33.45 rotation speed fine adjustment range ± 8% (continuously variable) W453 x H162 x D360 mm approx. 12.5 kg
A full-range speaker that uses a Satsuma Shimadzu 6cm DSS diaphragm. It is intended for low volume playback, so you can enjoy realistic sound that transcends size. The beautiful solid cherry wood enclosure is also attractive (Murakoshi Yoichi)
Maintenance information: 2024.4.18 sound output confirmed
Accessories: instruction manual, unit protector, cable hook, screws, + screwdriver, cross
Main specifications: 6cm full range 80dB 4Ω input resistance 15W main unit W150 x H260 x D210 mm, stand height 650 mm
RCA cable 1.9 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range. The printing on the sheath has disappeared (Kojima Yosuke)
Accessories: none
Stereo mini-phone conversion cable 2.0m cable for converting DAP earphone output etc. to each LR mono phone terminal. The phone terminals are manufactured by Neutrik (Kojima Yosuke)
Accessories: none
The current model of the project's belt drive player. The company's commitment is packed with everything from the 9.5 kg aluminum alloy platter and selected ultra-low noise synchronous motors to neodymium magnetic floating feet. Equipped with Ortphone's popular dynamic balance arm RS-309D! (MURAKOSHI Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: instruction manual, stabilizer, power cord, head shell, mounting screws, template, needle pressure gauge, dust cover, EP adapter, gloves
Main specifications: belt drive, compatible with 33, 45, 78 rotations, RS-309D: long arm needle pressure 0 to 5 g, cartridge weight 18 to 40 g (including shell), effective length 326 mm, effective length 311 mm, overhang 15 mm, height adjustment range 42 to 55 mm, W550 x H250 x 450 mm, 22 kg
A set of 2 seems to be a choke transformer, but the details are unknown. Measured DC resistance value 380/373Ω W31H95 x 44mm 0.31 kg/piece (actual measurement, not including protrusions), only conduction and resistance values have been confirmed by a tester (Kojima Yosuke)
Accessories: none
Power cable 2.0m PSE standard oxygen-free copper (OFC: oxygen-free copper) is an expressive power cable with high resolution, full of speed (Kojima Yosuke)
Accessories: none
Power cable, 1.5 m (1.5 m between plug tips), reproduces vocals more vividly by unplating the eyeglass type plug part. Improved image quality can also be expected when connected to a video device (Kojima Yosuke)
Accessories: none
Pair tube large transmission tube direct heat triode tube made in China gold base gold foot measured IP value 47mA/47ma (the best standard IP value for this amplifier is 50mA) with original box (part of the box is damaged) *Sound is checked with a test amplifier, plate current values have been measured, and it has been determined that operation is good (Kojima Yosuke)
Accessories: original box
Input transformer pair sale primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70H W50 × H70 × D57 mm 0.75 kg/piece (actual measurement, not including protrusions) The badge is discolored, and there are scratches in places (Kojima Yosuke)
Accessories: specifications
Input transformer pair sale primary impedance 10kΩ primary maximum superposition current DC15mA transformer ratio 1:2 primary inductance 60H maximum output voltage 150V use output tube 50, PX25, DA30, 300b, etc. W50 x H80 x D56mm 720g/piece with scratches and line damage in places and there are no TANGO badges (Kojima Yosuke)
Accessories: specifications
Output transformer pair sale single output 20W primary: 2.5/3.5/5 kΩ secondary: 8/16 Ω W78 x D83 x H120 mm approx. 2.1 kg/piece, no TANGO badges, and there are line damage or damage (Kojima Yosuke)
Accessories: none
Power transformer hammer tone color primary: 100V secondary: 320-280v-0-70V-380V/280V/280mA, 5V/3A, 2.5V-6.3V/5.2A x 2, 6.3V/3A application example: 2A3/6B4G/6L6/VT-52, etc. W120 x H120 x D105 mm approx. 5.2 kg (including actual measurement, protrusions) No TANG O badge, there are dullness and minor scratches in places (Kojima Yosuke)
Accessories: none
Choke transformer hammer tone color 15H/150mA DC resistance 155 Ω (measured 154.6 Ω) W84 x H105 x D75 mm 2.3 kg There are fine bumps and line scratches (Kojima Yosuke)
Accessories: none
Refreshed and maintained with attention to detail, such as replacing deteriorated parts! It's a beautiful item with a wooden case! An original C22, a famous machine admired by enthusiasts. The thick, soft, and strongly extruded tone is a pleasant tone that can only be experienced with an old McKinn. It has a rich tone centered around the middle range with a high concentration, and it sounds with plenty of realism. The wood case is made with a pan lock for replicas. Serial 53A03 (Murakoshi Yoichi)
Maintenance information: 2024.4.17 maintenance (front lamp wiring re-soldering procedure, AC cord, 1W and 1/2W replacement, TREBLE switching noise reduction measures → 1/4 W resistance added, RCA jack and vacuum tube socket re-caulking repair. Operation check with AC 100 to 117 V) 2016.2.5 maintenance completed (main volume disassembly and cleaning repair, EL.c40μf, EL.c100μf replacement, 2 additional diodes, RCA jack and VT socket caulking repair, parts check including Block.C OIL.C)
Accessories: none
Main specifications: 117 V specification, 4 input systems, 2 phono systems, frequency characteristics, 20 Hz to 20 kHz (± 0.5 dB), signal-to-noise ratio, 85 dB (high level), 62.5 dB (low level), distortion ratio 0.2%, W406 x H138 x D330 mm, 7.3 kg
Transformer attenuator pair sale Ritz line attenuation -1 to -20 dB (1 dB interval) maximum input 300 W (when 8 ohms) W74 x H72 x D85 mm 1.0 kg/piece There is dullness and discoloration on the terminals (Kojima Yosuke)
Accessories: none
RCA cable 4.9 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
RCA cable 2.0m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while having a firm thickness in the mid to low range. The printing on the sheath often disappears and there are seal marks on the plug shell (Kojima Yosuke)
Accessories: none
RCA cable 0.5 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
RCA cable 0.5 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
RCA cable 0.45m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
RCA cable 0.45m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
A line preamp that uses 2 WE 310A driver tubes and 1 Golden Dragon 5U4G rectifier tube. The rich tone has a strong personality reminiscent of foreign products, and the amount of information is also attractive. It is a compact preamp that has a relatively wide range and is fully compatible with modern speakers. The exterior is slightly dull. (YONEJIMA Satoshi)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: power cord
Main specifications: RCA/5R4GY x 1 WE/310A x 2 W330 x H215 x D250 mm 12.74 kg (actual measurement)
※1 unit only. Maintained! It is originally a professional mono amplifier, but there is only 1 unit. You can feel the strong power of the sound quality even with just one unit. It seems to be useful for mono and center speakers. The exterior has scratches and paint bald spots. Serial Q001769 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (XLR speaker cable created (3 meters), electrolytic capacitor replaced, cleaned due to ATT stiffness, solder corrected, rubber foot added due to missing rubber feet, bias offset check, output sound check. Input ① GND ② HOT ③ GND (unbalanced) output ① not used ② is set to plus ③ minus 8 Ω load. (Also, a popping sound is made when the power is on and off, which is a specification.)
Accessories: speaker cable, power cable
Main specifications: 8 ohms W482.6 x H88 x D320 mm weight 13 kg
Maintained! An amplifier with a black panel that exudes chic calm. Rather than being glossy like the PRA-2000, it sounds clear and straightforward, and has a sense of unity. It's an excellent product that blends in smoothly no matter what amplifier you combine it with. There are scratches on the exterior. Serial 6111100015 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (PHONO selector, tape monitor selector, SW disassembly contact polishing, cleaning, and grease application due to poor contact between each. (Improved by cleaning the balance VR and main VR contacts, and check the sound output for each other input/output connection.)
Accessories: instruction manual
Main specifications: MC/MM input with CD direct input W466 x H136 x D302 mm 6.3 kg
Rare amplifiers are in stock! Stereo power amplifier imported directly from Denmark. It is equipped with a B&O ICEPower200ASC that is also mounted on the JEFF ROWLAND Model 102. You can enjoy straight, high-resolution sound. As for the exterior, there are scratches and scuffs on the top plate. Serial 000913 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Operation confirmed
Accessories: power cord
Main specifications: 100W+100W (8Ω) impedance 3-16Ω W215 × H60 × D350 mm 3.5 kg
Comes with original box! IFI-Audio phono equalizer. It is a compact yet high-spec model equipped with 6 stereo equalizer curves, a load transfer switch for MC cartridges, an ultra-low noise MC stage, a load transfer switch for MM cartridges, and a gain adjustment switch. Serial microP11468 (Tomonori Asaine)
Maintenance information: 2024.4.19 Operation confirmed
Accessories: instruction manual, power adapter, original box
Main specifications: frequency characteristics 10 Hz to 100 kHz output impedance 110 ohms W68 x H28 x D158 mm weight 198 g
Bookshelf Speaker Floor Stand It is designed for small speakers such as the 705 and CM5, and is a stylish design that matches other speakers of similar size. The exterior is dull and has small scratches (Tomoho Asaine)
Accessories: none
Main specifications: external dimensions W275 x H600 x D365 mm top plate 160 x 200 mm bottom plate 275 x 365 mm 10 kg
The price has been reduced. 2024/3/23 sales price 20,000 yen*Currently sold. Both center caps have dents, and the dowel rubber on one side of the saran net is missing, etc., so the condition is poor, so it is inexpensive. Victor's 3-weight dollboy speaker It is a masterpiece that combines a glossy sound that spans the entire area with a clear mid-range. It is characterized by a clear sense of transparency in mid and high tones, and shows its true value with female vocals, etc. In addition to the appearance described above, there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.3.23 Operation confirmed
Accessories: instruction manual, saran net, jumper
Main specifications: 3-way 4-speaker system bass reflex type (anti-magnetic JEITA) 32 Hz to 80,000 Hz W300 x H1029 x D345 mm (including foot part) 22 kg
Comes with original box! IFI-Audio phono equalizer. It is a compact yet high-spec model equipped with 6 stereo equalizer curves, a load transfer switch for MC cartridges, an ultra-low noise MC stage, a load transfer switch for MM cartridges, and a gain adjustment switch. Serial microP11204 (Tomoho Asaine)
Maintenance information: 2024.4.19 Operation confirmed
Accessories: instruction manual, power adapter, original box
Main specifications: frequency characteristics 10 Hz to 100 kHz output impedance 110 ohms W68 x H28 x D158 mm weight 198 g
*9V/2.0A specification. An audio file-standard DC power adapter that uses “active noise cancellation +” using military radar technology (Asaine Tomoho)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
Main specifications: Approx. 150g (actual measurement)
*9V/2.0A specification. An audio file-standard DC power adapter that uses “active noise cancellation +” using military radar technology (Asaine Tomoho)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
Main specifications: Approx. 150g (actual measurement)
Unspecified mmType cartridge. It's very similar to the cartridge that comes with the DENON DP-500M. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Denon's classic shell. This is a genuine DA-305 shell. There is also plenty of room around the lead wire, and various cartridges can be attached. There is a feeling of use on the exterior such as small scratches and dullness (Tamai Jun)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Main specifications: dead weight 7g
Fidelity-Research headshell Lightweight and highly rigid. It is characterized by an enveloping shape with a thick aluminum press-processed body. There are dullness and small scratches on the exterior (Tamai Jun)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 10g
1.6m pair of unprocessed 0.12mm x 238 (OFC) speaker cables This cable has a sense of volume in the mid to low range and is compatible with a wide range of devices (Tomoho Asaine)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
Speaker cable 1.4+2.9 m pair end This is a well-balanced speaker cable, from powerful, unprocessed bass to delicate light sounds. There is a feeling of use such as dirt (Asae Tomoho)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
Speaker cable, 5,0m pair, untreated ends, an introductory cable that is soft and easy to run. The medium range is easy to hear and has a sense of volume, making it perfect for upgrading from accessories. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.4.19 continuity confirmed
Accessories: none
This is a genuine shell that comes with the DP-1300M/DP-500M. Black model with meat removal processing. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Unspecified EP adapter. Includes an overhang gauge and is equipped with a level gauge. There is a feeling of use on the exterior such as dullness and small scratches (Asaine Tomoho)
Accessories: none
Main specifications: Weight 62 g (actual measurement)
The price has been reduced. 2024/4/18 sales price 600 yen Nagaoka record cleaner using Italian velvet. The exterior shows a feeling of use such as dullness, etc., and wear on the velvet (Asaine Tomoho)
Accessories: none
The price has been reduced! 2024/4/18 sales price 1,000 yen RCA cable 1.3 m pair Audio-Technica RCA cable. Uses 24K gold-plated plugs and PCOCC conductors. The cable is soft, easy to handle, and easy to use. There is a feeling of use on the exterior such as dullness and small scratches (Asaine Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
The price has been reduced! 2024/4/18 sales price 500 yen*It's cheap because it deteriorates drastically! Audio-Technica record cleaner. High-grade velvet can be used to clean records gently and effectively. It's also perfect for those just starting to arrange records. The exterior shows a feeling of use such as dullness, etc., and wear on the velvet (Asaine Tomoho)
Accessories: none