FR heavyweight headshell In combination with a heavy needle and pressure needle, it exhibits excellent tracing performance, such as digging up from the back of a groove on a record board (Yasuhito Koshihama)
Maintenance information: 2024.4.25 continuity confirmed
Accessories: none
Main specifications: aluminum press processing actual measurement 19g
Denon's classic shell. This is a genuine DA-305 shell. There is plenty of room around the lead wire, and various cartridges can be attached (Oikawa Tetsuji)
Accessories: none
Main specifications: dead weight 7g
Orthophone's classic headshell. The finger tips are ergonomically designed and are designed to be easy to operate. It is light in weight and is compatible with various cartridges and tonearms. There is a screw scratch (Oikawa Tetsuji)
Accessories: none
Main specifications: aluminum gold-plated terminals, dead weight 9.4 g
A thick, highly rigid, heavyweight shell prepared by Orthophone for cartridges other than the SPU series. The cartridge ground surface is flat, has excellent adhesion, and is an easy-to-use head shell (Oikawa Tetsuji)
Accessories: none
Main specifications: machined aluminum alloy, self-weight 16g
A head shell with a round tip that matches the MC Jubilee and Kontrapunkt cartridge shapes. Its own weight is 14.6g, which is a bit heavy (Yasuhito Koshihama)
Main specifications: machined aluminum block, dead weight 14.6 g
Alloy die-cast headshell I like the simple design. This is one that is easy to match with various cartridges (Shota Sasaki)
Main specifications: magnesium alloy, die-cast, gold-plated contacts, dead weight 6 g
Denon's classic shell. This is a genuine DA-305 shell. There is plenty of room around the lead wire, and various cartridges can be attached (Oikawa Tetsuji)
Accessories: none
Main specifications: dead weight 7g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Sasaki Shota)
Accessories: none
Main specifications: aluminum stamping dead weight 8g
The price has been reduced! 2024/2/23 sales price 29,800 yen Manufacturer maintained! Phono motors only. It is a model that is responsible for Denon's volume zone, and rotation is controlled by a voltage support system that controls the AC power supply voltage of the same motor as the office unit. It has a reputation for its highly accurate rotation and smooth sound quality. There are threads and dullness throughout the exterior. Serial 9970 (Hiroki Aso)
Maintenance Information: 2024.2.23 Maintained (head gap adjustment leaf SW cleaning speed adjustment)
Accessories: copy of instruction manual
Main specifications: Servo-type direct drive Dimensions W370 x H139 x D374 mm Weight 6.7 kg
The price has been reduced! 2024/4/21 sales price 12,000 yen DENON tonearm DA-401 exclusive headshell. They rarely appear separately, so if you are looking for one, please take this opportunity (Tomoho Asaine)
Maintenance information: 2024.4.21 continuity confirmed
Accessories: none
Main specifications: dead weight 4 g
*Both the main body and ottoman are inexpensive because the leather is torn and leaves a feeling of use. Ottoman with optional swing table Scandinavian design stressless chair. It is the best recliner that reclines naturally by simply putting weight on the backrest, and lifts up the backrest at the same time as the body is raised ※Shipping is estimated separately. In addition to the exterior, as described above, a feeling of use can be seen, such as dullness, threads, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W75×H96-106×D75mm ottoman W55×H40×D41mm
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Sasaki Shota)
Accessories: none
Main specifications: aluminum stamping dead weight 8g
The disposal price has been reduced. Member discounts are not applicable. 2024/4/21 sales price 148,000 yen ※ The hinge is damaged, but there are no replacement parts, so this is the current situation. Maintained! Armless PD444 Long arms and short arms can be set, and an original system can be built by placing an arm of your choice on it. The highly rigid chassis and flexible suspension create a tight, easy-to-see sound (Murakoshi Yoichi)
Maintenance information: 2024.4.20 maintenance (power supply circuit, motor servo circuit electrolytic capacitor replacement, power lamp LED replacement, each rotation lock check. (Arm base lock lever with E-ring attachment)
Accessories: motor fixing beads, EP adapter, dust cover, instruction manual, armrest
Main specifications: Direct drive system, quartz control, 30cm, die-cast aluminum turntable, 33/45 rpm, 2 speed switching, W664 x H160 x D392 mm, 22 kg
※Inexpensive because it is in poor condition. Self-made 2way/3way enclosure. The size of the hole is different at the top, with an opening diameter of about 315 mm on the top and about 360 mm on the bottom. There are many peeling veneer, corner pads, scratches, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: W450 x H1056 x D480 mm approx. 33 kg
with logo! This headshell is popular due to its combination with the Technics and SL-1200 series. It is made of aluminum die-cast with high rigidity, and brings out the characteristics of the cartridge (Hiroki Aso)
Maintenance information: 2024.4.17 continuity confirmed
Accessories: none
Main specifications: Die-cast aluminum, dead weight 10.2 g
Fidelity-Research headshell Lightweight and highly rigid. It is characterized by an enveloping shape with a thick aluminum press-processed body. There are dullness and small scratches on the exterior (Tamai Jun)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 10g
Audio-Technica's lightweight hard shell. It is compatible with cartridges that are sharp and sharp. The connection between the fuselage part and the arm is made of separate parts, making it difficult for extra signals to be transmitted. (TAMURA Eiji)
Maintenance information: 2024.3.30 continuity confirmed
Accessories: none
Main specifications: aluminum dead weight 12 g (actual measurement)
The disposal price has been reduced! (Member prices are not applicable) 2024/4/13 sales price 398,000 yen For the first time in about 7 years, CM10S2 has arrived! It lets you listen to high-response sounds. In addition to simplifying the crossover with Mundorf EVO capacitors, all important internal components have been improved, such as Vandenhall internal wiring, nickel-plated terminal trays, and the driver's anti-vibration dust plug. As for the exterior, there are scratches, threads, and deterioration in part of the urethane. Serial 1508-0011895, 1508-0011896 (Fujisawa Yukishi)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, saran net, spikes, rubber feet, jumper plates
Main specifications: 3-way bass reflex type playback frequency band 28 Hz to 50 kHz output sound pressure level 90 dB nominal impedance 8 ohms W366 x H1087 x D414 mm weight 33.5 kg
The die-cast aluminum shell has no screws, has a heavy weight, is sturdy, and the design is stylish and creative. Rigidity is high and low frequency tightness can be expected (Mizushima Itsuro)
Maintenance information: 2024.4.22 continuity confirmed
Accessories: none
Main specifications: Die-cast aluminum, self-weight 10.6 g
Yamaha perforated lightweight shell. It is lightweight and strong due to aluminum press processing. The exterior and finger tips are straight, and a feeling of use such as dullness can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.4.19 Continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 9g
Air-tight KT88 push-pull The modern sound, which combines the soft texture unique to vacuum tubes and the high resolution, is attractive. There are 2 inputs at the front and rear, and the front input can be directly connected to the first stage tube without going through a shielded wire. The front panel is equipped with a meter that can check the optimal operating point of the output tube. There are many scratches on the bottom plate, and there are paint chips, threads, and bumps on the transformer (Oikawa Tetsuji)
Maintenance information: 2024.4.22 operation confirmed
Main specifications: used vacuum tube KT88 x 4, ECC83 x 2, 5814A x 2, 12BH7A x 2, 12BH7A x 2, 80W+80W 8Ω, W415 x H223 x D380 mm, 32 kg
The price has been reduced. 2024/4/15 sales price 35,000 yen It is a high-end masterpiece that has been loved by Sennheiser for a long time. As a studio monitor, it demonstrates its power without regret. It expresses delicate sound and clear space, and provides both vocals and performances with high resolution. There is a slight feeling of use on the earpads (Kanai Hidetsugu)
Maintenance information: 2024.4.15 sound output confirmed
Accessories: original box, instruction manual, cable
Main specifications: dynamic open air, 300 ohms, 103 dB, playback frequency band 10 to 39,500 Hz, cable length: 3.0 m, mass: approx. 260 g
*The headshell is an SPU-G (M) one, but the body is inexpensive because it is GE. Needle cover missing. G-shell oval needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal staple cartridge that fully conveys the original appeal of analog. The exterior has rust on the metal parts, and dullness and dirt throughout the body. The needle tip is in good condition (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
The price has been reduced! 2024/4/13 sales price 89,800 yen ※It is cheap because it has a tobacco smell. A network player compatible with Roon Ready and MQA sound sources. Equipped with two Asahi Kasei flagship DAC chips AK4497, which are now rare, you can fully enjoy high-resolution sound sources. It also plays DSD 22.5 MHz when used as a USBDAC. Since it also has volume, it can also be used as a digital preamp. The exterior has a slight smell of threads and tobacco. Serial 17Y0011 (Fujisawa Yukishi)
Maintenance information: 2024.4.13 operation confirmed
Accessories: remote control, power cord
Main specifications: USB DAC compatible frequency (PCM44.1/48/88.2/96/176.4/192/352.8/384/705.6/768kHz DSD2.8/5.6/11.2/22.5MHz) LAN input compatible frequency (PCM32/44.1/48/88.2/96/176.4/192/352.8/384kHz DSD2.8/5.6 MHz) compatible format (FLAC, Apple Lossless, WAV, AIFF, MQA) W290 x H81.2 x 248.7 mm 3.9 kg
The disposal price has been reduced (member prices are not applicable). 2024/2/16 sales price 378,000 yen ※The power supply part has been newly created. Other internally deteriorated parts have been restored! 2-way 100Hz specification An electric crossover coveted by Mark Levinson fans. You can see how well the early Levinson was built can be seen from the feel of the knobs that seem to make you addicted. You can listen closely to Levinson's unique sounds even on Divider. The exterior has scratches on the front top plate and other threads (Mizusaki Ryo)
Maintenance information: 2024.2.16 Maintained (*Since there is no power source, new power supply and connection cable were manufactured, noise appears in the LChLow output, transistor defects in the low pass module were replaced, re-encapsulated, readjusted due to left and right level differences, 4 volume contacts were cleaned, specs were inspected, and blocking characteristics were inspected. The crossover is 100Hz)
Accessories: Power supply unit (newly created, non-genuine), power cable, copy of instruction manual
Main specifications: 2 way (100 Hz specification) closed module type RCA Remo input/output size (main unit) W483 x H51 x D156 mm 2.8 kg size (power supply part) W101 x H101 x D256 mm 2.2 kg
Denon's classic shell. This is a genuine DA-305 shell. There is also plenty of room around the lead wire, and various cartridges can be attached. There is a feeling of use on the exterior such as small scratches and dullness (Tamai Jun)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
Main specifications: dead weight 7g
This is a genuine shell that comes with the DP-1300M/DP-500M. Black model with meat removal processing. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.4.19 sound output confirmed
Accessories: none
with logo! This headshell is popular due to its combination with the Technics and SL-1200 series. It is made of highly rigid die-cast aluminum and brings out the characteristics of the cartridge (Murakoshi Yoichi)
Maintenance information: 2024.4.17 continuity confirmed
Accessories: none
Main specifications: Die-cast aluminum, dead weight 10.2 g
Unspecified silver shell. There is a feeling of use due to appearance, dullness, abrasions, etc. (Asae Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
Main specifications: dead weight g (actual measurement)
The price has been reduced. 2023/5/31 sales price 85,000 yen Asahi Lumber horizontal rack. It is a model with plenty of storage capacity and adjustable height. As an audio rack, its performance is high, and it is a stable unit. It is made of full-body natural wood, has a sturdy structure, and is highly decorative. ※Since this is a large item, shipping costs will be estimated separately. There are scratches, threads, etc. on the exterior. Also, felt is attached to the bottom (Takasaki Atsushi)
Accessories: none
Main specifications: W1227×D565×H1060mm
※Only 1 bottle is currently sold because it is cheap. Bookshelf speakers made in England. It features compact, tight low frequencies and stretchy mid-high frequencies. There are scratches, threads, and the smell of oil (Daiki Goto)
Maintenance information: 2024.4.10 operation confirmed
Accessories: none
Main specifications: 89dB 6Ω W210 × H380 × D220 mm 5.4 kg
One of the few straight arm headshells. The small die-cast aluminum has high rigidity, and in combination with the straight arm, you can enjoy tight analog sound. There is little feeling of use and it is generally good (Mizushima Itsuro)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
Main specifications: aluminum die-cast straight arm for weight 5g
Heavyweight metallic design headshell Technihard materials are used for surface treatment. It can be expected to tighten the sound (Tamura Eiji)
Maintenance information: 2024.3.30 continuity confirmed
Accessories: none
Main specifications: aluminum 15g
The basic structure of the 1.1 m pair end of the speaker cable remains the same as the previous model, and it is a speaker cable with excellent cost performance made by making the 102SSC precision conductor precise with patented 3E twisting technology. There is a feeling of use such as threads and dirt on the sheath (Kanai Hidetsugu)
Maintenance information: 2024.3.30 continuity confirmed
Accessories: none
Main specifications: 102 SSC conductor 1.25 SQ (37 strands/3E strand) outer diameter 3.5 x 8.0 mm
※It is inexpensive because the condition is poor due to scratches, threads, and partial sheath deformation. Off sale power cable, 1.0 m, has an unprocessed end that combines performance and safety at an astonishing level. There are dirt and scratches on the exterior (Tamura Eiji)
Accessories: No accessories
An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
*Currently sold. The classic 101 mm small speaker. The sound, which has been compiled in one small full-range shot, makes all kinds of popular music sound cheerfully. The exterior has scratches, threads, and dullness. There is also a dent in the saran net. Serial 108023/089692 (Tamura Eiji)
Maintenance information: 2024.3.3 sweep check OK
Accessories: saran net
Main specifications: 1 way 1 speaker impedance 6 ohms maximum input 150 W output sound pressure level 86 db W232 x H154 x D172 mm 2 kg
※Since it is cheap, it will be handed over as is. A subwoofer that can also be installed in a home theater or for those with insufficient bass in the system. The settings are simple, and you can create sound according to the speaker and room conditions. The exterior has some holes in creases and threads. Serial Z213158SU (Yonejima Satoshi)
Maintenance information: 2024.2.24 sweep check OK
Accessories: instruction manual
Main specifications: 1 way, 1 speaker, advanced YST system, floor type, anti-magnetic high cut filter, 50 to 150 Hz, continuously variable, W235 x H485 x D409 mm, 14 kg
Set of 4 Use ICP damping spacers and IDS composites together as tuning goods to counteract speaker vibrations. *Cannot be used as a receiver for metal spikes. There are scratches and threads on the exterior (Yonejima Satoshi)
Accessories: No accessories
Main specifications: diameter 35 mm x 3 mm (thickness)
Undetailed, headshell similar to the exterior of the Technics SH-98D. It's a simple dish that seems to be easy to use (Oikawa Tetsuji)
Accessories: none
Main specifications: dead weight 7.3 g (actual measurement)
Coral headshell The weight has been reduced, and the mounting position can also be adjusted, so it is an easy shell to handle (Oikawa Tetsuji)
Main specifications: dead weight approx. 14g
DP-1300M heavy headshell counterweight, set of 2 types, large and small A must-have item for those who use heavyweight cartridges such as SPU and FR. It can also be attached to the DP-500M. Recommended for those who use a variety of cartridges. There is slight dullness on the exterior (Murakoshi Yoichi)
Accessories: none
Main specifications: Compatible cartridges for their own weight/for 20 to 28 g (small) /for 26 to 37 g (large)
Center speaker stand from unknown manufacturer. It is a type that is easy to handle, with wooden casters. There are threads on the exterior. (MIURA Kimiya)
Accessories: none
Main specifications: W570 ✕ H225 ✕ D440mm 4kg
Wood cabinet for TD-124 of unknown manufacturer. It can be equipped with an SME long arm. The exterior has scratches, threads, chips, etc. (Tamura Eiji)
Accessories: no accessories
Main Specifications: W597 ✕ H160 ✕ D445mm Weight 3.9 kg
※1 XLR cable 1.5m male phone jack plug is made by Neutrick and is originally a microphone cable, so sound removal is good. There is an appearance, threads, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
Main specifications: Electromagnetic shielded microphone cable, 4 cores, outer diameter: 6.0 mm
Jack (female) to RCA cable 2.0m pair plug are both ends made by Neutrick and are originally microphone cables, so sound loss is good. There is an appearance, threads, and a feeling of use (Kobayashi Hitoshi)
Maintenance Information: 2023.9.16 Conductivity Confirmed
Accessories: none
Main specifications: Electromagnetic shielded microphone cable, 4 cores, outer diameter: 6.0 mm
Jack (male) to XLR (male) cable 2.0m pair plugs are both ends made by Neutrick and are originally microphone cables, so sound loss is good. There is an appearance, threads, and a feeling of use (Kobayashi Hitoshi)
Maintenance Information: 2023.9.18 Conductivity Confirmed
Accessories: none
Main specifications: Electromagnetic shielded microphone cable, 4 cores, outer diameter: 6.0 mm
※ The effect of the brake is bad, but it is currently sold. Victorola's tabletop gramophone. The antique-style exterior stirs up the desire to own it. The sound is also an item full of nostalgic charm that cannot be created with modern audio. The exterior has dullness, scratches, and threads (Yoichi Murakoshi)
Maintenance information: 2022.8.123 Sound output confirmed
Accessories: none
Main specifications: W394 × H340 × D488 mm (excluding handle) 19.6 kg