Speaker cable 2.0m pair A standard BELDEN speaker cable nicknamed “sea snake” with untreated terminals. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Air-tight KT88 push-pull The modern sound, which combines the soft texture unique to vacuum tubes and the high resolution, is attractive. There are 2 inputs at the front and rear, and the front input can be directly connected to the first stage tube without going through a shielded wire. The front panel is equipped with a meter that can check the optimal operating point of the output tube. There are many scratches on the bottom plate, and there are paint chips, threads, and bumps on the transformer (Oikawa Tetsuji)
Maintenance information: 2024.4.22 operation confirmed
Main specifications: used vacuum tube KT88 x 4, ECC83 x 2, 5814A x 2, 12BH7A x 2, 12BH7A x 2, 80W+80W 8Ω, W415 x H223 x D380 mm, 32 kg
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an unprocessed 1.7 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 1.0 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.6 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.5 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/7 sales price 398,000 yen Exterior maintenance completed! Replace network capacitors with SOLEN film capacitors. The unit is DENTECH Tune HDP385, and the enclosure is made by Shinkosha. The unit is attached by removing the back plate, and the net does not come off the front. Classical music also goes well with symphonies. The exterior is generally beautifully finished due to maintenance. Serial AYT71012 AYT71012 (Tomonori Asaine)
Maintenance information: 2024.3.7 Maintained (exterior repair/cleaning)
Rear baffle paint saran net replacement unit maintenance (exterior cleaning, low range center adjustment, screw tightening, high frequency magnetic circuit slit cleaning/center adjustment) ATT cleaning/knob adjustment unit detachment)
2015.5.14 Maintained (network capacitors replaced with SOLEN. Unit edge replacement. Magnetic circuit overhaul and operation adjustment. Saran net partial cleaning net tear repair, complementary color correction)
Accessories: none
Main specifications: used unit HPD385 frequency characteristics 20Hz to 20kHz allowable input 85W 92dB 8Ω W600 x H1075 x D380 mm approx. 42 kg/bottle
Internal and external maintenance has been applied and brushed up. The vivid sense of dynamism and the sharpness of the high frequencies typical of YAMAHA have been revived. It has a low frequency thickness that 1000 monitors don't have. It is a timeless masterpiece with a clear sense of transparency, upper and lower driving force, and the smooth connection, and the heavy exterior with an ebony finish that stands out at a glance even today. It is in good condition due to maintenance. Serial 11478L 11478R (Yamato Yuki)
Maintenance information: 2024.4.1 operation confirmed
2023.9.4 Maintained (exterior repair/polishing/clear finish. Rear baffle repair/painting. Saran net replacement. Unit frame painting. Network maintenance (Since the terminals have already been replaced with external products, adjust the direction and tighten, apply a screw fastener, and replace the mounting screws. ATT contact status check (check that there are no gaps). A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Input/output waveform and balance check, sound output check) Unit detachable)
Accessories: saran net
Main specifications: 3-way sealed playback frequency band 40Hz to 20kH sound pressure level 90dB rated input 50W maximum allowable input 100W impedance 8Ω crossover frequency 500Hz/6kHz dimensions W395 x H710 x D349 mm 39 kg
The price has been reduced. 2023/9/27 sales price 45,000 yen*The volume on the remote control cannot be controlled. Maintained! A small gap appears when switching between source direct SW, but this is the current situation. Maintained! A pre-main amplifier that allows you to enjoy tight low frequencies and extended high frequencies. It lets you listen to a performance that is faithful to the sauce and has no unnecessary flavorings, so it is compatible with any genre. The clean design fits well into the room. Serial 201711 (Murakoshi Yoichi)
Maintenance information: 2023.9.26 maintained (replacement VR, speaker relay, MUTING switch, power supply resistance 120Ω replacement, various board dirt cleaning and solder repair, function electric SW, direct SW disassembly contact cleaning, other DC bias DC balance adjustments.)
Accessories: remote control, instruction manual (copy)
Main specifications: 100W+100W (8Ω) line input, 3 tape systems, PHONO (MM/MC), W470 x H170 x D435 mm, 21.3 kg
The price has been reduced! 2024/3/6 sales price 25,000 yen speaker cable 1.0 m pair banana on both ends uses the company's highest-grade cable material. Recommended for those who want to improve the tightness of the low frequencies. On the exterior, there is a part where the rubber ring on the terminal is off. ※The cable is stiff, so please be careful when routing (Tamura Eiji)
Maintenance information: 2024.3.6 continuity confirmed
Accessories: No accessories
The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg
An adapter that converts a pin plug into an L type. L-type conversion, convenient for connecting in tight spaces, etc. The terminals have an all-metal body with a gold-plated finish (Tetsuji Oikawa)
Accessories: original box
Main specifications: 2 pieces, 1 pair, outer diameter 12 mm