*Needle cover missing. Popular DJ cartridges! Surprisingly, the sound quality is moist, centered around the mid-range, and the sound quality is superior to audio without extreme exaggeration (Murakoshi Yoichi)
Maintenance information: 2026.10.10 sound output confirmed
Accessories: none
Main specifications: mm needle Concord series output 6 mV playback band 20 Hz to 22 kHz proper needle pressure 3 g dead weight 18.5 g
* Since the shaft of the weight part of the arm is more saggy than normal, it is sold at a low price. It is a walnut bar that looks beautiful. The Ortofon 9-inch short tonearm TA-110 is standard equipment, and a magnetic support system is used for the bearings that support the platter, adding a sense of silence and stability. It's one that brings out the best of cartridges to the fullest with its accurate sound. There are small scratches on the exterior. (TAMURA Eiji)
Maintenance information: 2026.10.10 Operation confirmed
Accessories: instruction manual, AC adapter, stabilizer, shell, phono cable (replacement)
Main specifications: belt drive type W465 x H x 185 x D 350 mm weight 18 kg
Popular model of MC step-up transformer. In addition to switching the primary impedance of 3, 6, 12, 24, and 48 ohms, it can be bypassed, making it extremely easy to use. The sound is rich and powerful, and it is a trance known for its high ability. There is a feeling of use on the exterior, such as small scratches and dullness, and white marks on the top plate (Asaine Tomoho)
Maintenance information: 2026.10.10 sound output confirmed
Accessories: connection cable
Main specifications: boost ratio 3 ohm · 32 dB, 6 ohm · 29 dB, 12 ohm · 26 dB, 24 ohm · 23 dB, 48 ohm · 20 dB playback frequency band 4 Hz to 120 kHz W80 × H40 × D150 mm 761 g
Comes with original box! This is the SPU GTE 105 with an elliptical needle that was revived as a regular model on the 105th anniversary of the founding of Orthophone. It has a built-in transformer jointly developed with Lundahl in Sweden, and like conventional GTs, it can be directly connected to a PHONO input for MM, and its power is attractive (permanent future fight)
Maintenance information: 2026.10.10 sound output confirmed
Accessories: instruction manual, original box, needle cover
Main specifications: output voltage 1kHz, 5cm/sec.4mV frequency characteristics 20Hz-25,000Hz±3db needle pressure range 3.0-5.0 g suitable needle pressure 4.0 g recommended load impedance 47 kΩ dead weight 34 g
Set of 2 classic Concords An orthophone cartridge for DJ use. It has a moderate mid-range thickness and fine texture, which is supported by general audiophiles. (FUJISAWA KOSHI)
Maintenance information: 2026.10.10 Operation confirmed
Accessories: case, needle cover
Main specifications: output voltage 5 mV channel segregation 20 dB (1 kHz) frequency characteristics 20 to 18,000 Hz suitable load impedance 47 kΩ slitus cone suitable needle pressure 4 g dead weight 18.5 g
The disposal price has been reduced. Member discounts are not applicable. 2026/9/27 sales price 118,000 yen A must-see item for SPU fans. It is a model loaded with 2 Type0.32m/No. 6600 JS transformers, and the characteristics of the Ortofon/SPU series are fully brought out, and the depiction of vividness rich in thickness and stickiness is amazing. In addition to the exterior and paint peeling, you can also see a feeling of use such as dullness, rust, scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.9.25 sound output confirmed
Accessories: none
Main specifications: boost ratio 31 times primary impedance 1.5 ohm/secondary impedance 1.5 kΩ dimensions W90 x H65 x D80 mm weight approx. 400 g
The price has been drastically reduced. 2026/9/14 sales price 148,000 yen Maintained. Dynamic balance short arm The strong sound brings out the characteristics of the SPU-G shell type to the fullest (Oikawa Tetsuji)
Maintenance information: 2026.9.14 Maintained (disassembly repair adjustment due to broken resin bearing coupling. Horizontal bearing cleaning. Attached because the stopper is broken. Internal wiring has been redone. Additional elastic coupling adjustments. Counterweight balance adjustment Arm cable solder fix. Screw thread adhesive peeling cleaning for armrests. Missing fixing nuts and washers added. Continuity test OK)
Accessories: phono cable, armrest, screws
Main specifications: Dynamic balance type, total length: 300 mm, execution length: 228 mm, overhang: 16 mm, needle pressure range: 0 to 7.5 g, needle pressure range: 0 to 7.5 g, direct reading arm, base hole, 22 mm, cartridge dead weight: 7 to 32 g
Maintained! Elliptical type with built-in step-up transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior is dull (Tomonori Asae)
Maintenance information: 2026.9.26 maintained (damper adjustment, installation angle correction, transformer Lch disconnection replacement)
Accessories: Needle cover, original box*torn. Needle cover is not included.
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g
Currently sold. Although it is compact, it can be said that it is quite good when it comes to tuning for human voices. Recommended for those thinking about space-saving use next to the desk. You can see a feeling of use, such as appearance, dullness, small scratches, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.9.6 sound output confirmed
Accessories: saran net
Main specifications: Unit: aluminum die-cast frame, 10cm cone woofer, 20mm soft dome tweeter, allowable input, 20W to 60W, impedance 6 ohms, crossover frequency 3.8 kHz, W140 x H218 x D210 mm, 2.8 kg
※Since the emblem is attached by rotating 90 degrees, it is inexpensive. SPU-GE reprint model. This is a popular oval needle type. It has a rich texture, a thick outline, a rich texture and thick outline that sets it apart from other cartridges. The cantilever is dull. (GOTO Daiki)
Maintenance information: 2026.8.28 Operation confirmed
Accessories: needle cover
Main specifications: G shell oval needle MC type output 0.2 mV suitable needle pressure 4 g internal impedance 2 ohms dead weight 30 g
The standard mono needle and the highest peak CG25D is now in stock. A precise, thick, and thick sound. The unique sense of density, which is different from stereo needles, is attractive. The exterior has dullness, small scratches, and chips on the plastic part around the needle tip. Serial 400287 (Murakoshi Yoichi)
Maintenance information: 2026.7.12 sound output confirmed
Accessories: original box with different model numbers, needle cover
Main specifications: mono round needle, MC type, output voltage: 1.5 mV, proper needle pressure: 3.5 g, dead weight: 32 g
The disposal price has been reduced. Member discounts are not applicable. 2025/12/20 sales price 99,800 yen Maintained! It comes with a Herman mark! Mono cartridge CA25D. One of the pinnacle of mono needles. The density unique to mono needles, which is not found in stereo needles, is attractive. There is rust on the cantilever. Serial 135502 (Murakoshi Yoichi)
Maintenance information: 2025.12.19 Maintained (damper replacement, coil adhesion repair)
Accessories: original box, needle cover, brush
Main specifications: mono round needle, MC type, output voltage: 1.5 mV, proper needle pressure: 3.5 g; dead weight: 31 g
Orthophone CA25D headshell It is rare that only shells are in stock. If you are looking for one, by all means (Daiki Goto)
Accessories: none
Main specifications: dead weight 22g (actual measurement)