Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Maintained in January 2024! It is a Harves speaker with increased appeal, such as the richness of the sound typical of an HL MONITOR. The Harves-like sound, which is characterized by a relaxed sound in addition to the mid-range density unique to those made in England, is attractive. Exterior maintenance has been carried out on the exterior, but in addition to scattering repair marks, there is a feeling of use over time, such as undulations on the woofer edge. *Saran net is not included. Serial 3349A 3349B (Tomonori Asaine)
Maintenance information: 2024.1.12 Maintained (exterior repair stain tinted front baffle repair polishing paint rear baffle cleaning
Woofer edge repair, protective agent application (with undulations), terminal replacement unit, detachable tweeter, corrosion, disconnection repair, diaphragm, dome coat treatment, 1 voice coil, bobbin deformation correction)
Accessories: none
Main specifications: 2 way 2 speakers, 22.5 cm cone woofer/2.5 cm soft dome tweeter impedance 8 Ω crossover 2,000 Hz sound pressure level 87 dB, W325 x H640 x D330 mm, 13.5 kg
*Currently sold. YAMAHA monitor speaker series. Since it is the same 3-way as 1000m, the resolution is also high, and the sound quality allows you to feel the spaciousness. Although the price and size are reasonable, you can fully experience the sound of a Yamaha monitor, and it is an ideal model as an introductory machine. The exterior is scratched and dull, and there is a feeling of use such as dents on the grill.*There is a slight crack on the ATT. Serial 111543L 111543R (Asaine Tomoho)
Maintenance information: 2024.4.18 Sound output operation confirmed
Accessories: none
Main specifications: 3 way 3 speakers sealed 90dB 6Ω W276 x H496 x D251 mm 12.0 kg
* There is no problem with the sound quality, but since there is a dent correction mark on the tweeter on one side, it is inexpensive and is currently sold. An authentic speaker that produces well-balanced sound quality from a compact cabinet. The mid-high range, which has a good sense of signal even at low volume, really makes you feel like a modern speaker. Stringed instruments and pianos in particular have a luster and are recommended
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box
Main specifications: 2-way 2 speakers, frequency characteristics, 50 Hz to 26.5 kHz, input sensitivity, 88 dB impedance, 6 ohms, W205 x H351 x D293 mm, 6.3 kg per unit
Maintained by Denon! This is DENON's mid-range model, and is a staple machine with an excellent sense of stability, with firm bass and delicate high frequencies. In addition to the bass energy from conventional models, you can enjoy well-balanced sound that takes into account the high mid to high frequencies with a high sense of transparency. There are small scratches on the exterior. Serial 8061507480 (Tamura Eiji)
Maintenance information: 2024.4.17 manufacturer maintained (Rch amplifier circuit, transistor and resistor replacement. Amplifier board soldering correction (both channels). (Idle current adjustment and operation inspection carried out.)
Accessories: instruction manual, power cable, original box
Main specifications: rated output 80W+80W (8Ω) PHONO1 system (MM/MC switching) dimensions W434 x H181 x D480 mm weight 24.0 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/15 sales price 79,800 yen Maintained! JBL professional 2 inch screwdriver It is an item that continues to be used today in large horn systems, etc. The quality unique to titanium diaphragms makes the vocal breathing, drum hi-hat, and outstanding realism no matter which one you take. The exterior has dullness, scratches, rust, etc. due to use over time. Serial 53400 63923 (Tomonori Asaine)
Maintenance information: 2023.12.15 Maintained (diaphragm installation adjustment throat cleaning DCR 63923/8,3 ohm, no vibration damage
(DCR 53400/7.8Ω vibration has scratches and small dents)
Main specifications: throat diameter 5 cm; allowable input: 100 W; sound pressure level: 111 dB/w/m; frequency characteristics: 500 Hz to 20 kHz; crossover frequency: 500 Hz or more; 16 ohms; diameter: 235 x depth: 132 mm; 13.6 kg/1
Maintained by the manufacturer! This model was the first to use an ALPHA processor in the best-selling 1650 series. The mid and low frequencies are quite stable, and the balance depicts rich, rich music regardless of genre. There are dents on the front panel and footprints on the top plate (Oikawa Tetsuji)
Maintenance information: 2024.4.17 manufacturer maintained (inside the CD mechanism, loading belt, tray opening/closing SW replacement. The HF level for laser pickups is within the regulations and is fine now. Sound output test)
Accessories: remote control, instruction manual
Main specifications: Real 20-bit 4DAC/Lambda Super Linear Converter with 20-bit 8x oversampling digital filter+GIC 3rd order analog filter frequency characteristics 2Hz to 20kHz W434 x H120 x D340 mm 10.2 kg
Maintained by the manufacturer! This model was the first to use an ALPHA processor in the best-selling 1650 series. The mid and low frequencies are quite stable, and the balance depicts rich, rich music regardless of genre. The exterior has dents on the front panel corner, and there are line scratches, small scratches, dullness, etc. ※The remote control is out of stock (Oikawa Tetsuji)
Maintenance information: 2024.4.17 manufacturer maintained (inside the CD mechanism, loading belt, tray opening/closing SW replacement. VR has been reworked. The HF waveform of the laser pickup is within the regulations and is currently fine. Sound output test)
Accessories: copy of instruction manual ※ remote control missing
Main specifications: Real 20-bit 4DAC/Lambda Super Linear Converter with 20-bit 8x oversampling digital filter+GIC 3rd order analog filter frequency characteristics 2Hz to 20kHz W434 x H120 x D340 mm 10.2 kg
※It has a cigarette smell, so it's cheap. Class D power amplifier compatible with DSD 11.2 MHz and PCM384 kHz/32 bit inputs. When reproducing a digital source, all processing from input to output can be performed in the digital domain. It is also equipped with a USB-DAC function and Bluetooth function, so you can enjoy music with high sound quality from a PC to a smartphone. As for the exterior, there are some square brackets. Serial AXD36190304432 (Tamura Eiji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: remote control, power cable
Main specifications: rated output 20W+20W (8Ω) 40W+40W (4Ω) speaker load 4-16Ω analog audio input terminal/unbalanced input × 1 digital audio input terminal/USB-B input × 1 coaxial digital input × 1 optical digital input × 2 W200 × H86 × D258 mm 2.7 kg
※It has a cigarette smell, so it's cheap. Yamaha commercial power amplifier. This is an easy rim-sized Yamaha commercial amplifier. The overall output is flat with elegant sound quality. There are dirt and scratches on the exterior. Serial 11505 (Tamura Eiji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: none
Main specifications: 45W+45W (8Ω) left and right independent variable volume S/N ratio 110dB W480 x H94 x D338 mm
The price has been drastically reduced! 2024/2/23 sales price 39,800 yen This is an 8 ohm specification Japanese 1 inch driver developed for professional use. A must-see for anyone who owns the company's AH-501 horn. It makes a penetrating treble and deep mid-range sound unique to CORAL. It is also recommended for those who make their own speakers. There is paint peeling on the exterior. Serial 1304, 1325 (Fujisawa Yukishi)
Maintenance information: 2024.2.23 Operation confirmed
Accessories: No accessories
Main specifications: throat diameter 25.4 mm (1 inch) sound pressure 104 dB impedance 8 ohms playback frequency 500 Hz-18 kHz magnetic flux density 18000 gauss maximum input 100 W diameter 120 x H74 mm 3.3 kg/piece
The disposal price has been reduced. Member prices are not applicable. 2023/5/13 sales price 250,000 yen*The main volume, BASS, and TREBLE knob textures are different from the original. Internal parts have been thoroughly reviewed and maintenance has been carried out! This is a control amplifier from Sony's high-end brand, the Esprit series. Straight sound with a sense of speed similar to the TA-E900. The outline is clear and the sound image is drawn clearly. It is a vintage speaker and is especially recommended for jazz and rock fans. On the exterior, in addition to dullness and small scratches, there is a feeling of use, such as sticker marks on the top plate. Serial 200616 (Hiroki Aso)
Maintenance information: 2023.3.4 maintained (running test by refining the I/O board and screw parts) 2022.10.1 maintained (condenser semi-fixed resistance relay LED lamp IC spark killer Capricorn washer replacement implementation all SW VR disassembly cleaning board solder surface re-solder input/output waveform confirmation and left and right balance confirmation comprehensive operation test)
Accessories: copy of instruction manual
Main specifications: 2 PHONO inputs, 5 line inputs, 2 pre-out systems, W480 x H105 x D465 mm, 12.5 kg
Balance cable 0.7 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound yet has a firm thickness in the mid to low range. The printing on the sheath has disappeared (Kojima Yosuke)
Accessories: none
Balance cable 0.6 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
Balance cable 0.6 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
Balance cable 0.5 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
※Only 1 balance cable is 9.9m. This is a standard BELDEN line cable with a firm outline of the Neutrik plug sound, yet has a particularly firm thickness in the mid to low range. The printing on the sheath part has disappeared (Kojima Yosuke)
Accessories: none
※Only 1 balance cable is 4.9m. This is a standard BELDEN line cable with a firm outline of the Neutrik plug sound while also having a firm thickness in the mid to low range. The printing on the sheath part often disappears (Kojima Yosuke)
Accessories: none
※Only 1 balance cable, 4.9m, is a standard BELDEN line cable with a firm outline of the Neutrik plug sound while having a firm thickness in the mid to low range. The printing on the sheath part has disappeared and there are seal marks on the plug shell (Kojima Yosuke)
Accessories: none
* No. 3 hot specification RCA-XLR conversion cable, 3.9 m pair, both end plugs are a standard BELDEN line cable that clearly shows the outline of Neutrik's sound yet has a firm thickness, especially in the mid to low range. The sheath printing disappears a lot (Kojima Yosuke)
Accessories: none
RCA cable 0.5m pair REAN (Neutrik) RCA plug This is a standard BELDEN line cable that clearly outlines the sound while having a firm thickness, especially in the mid to low range (Fujisawa Yukishi)
Maintenance information: 2024.4.16 continuity confirmed
Accessories: No accessories
RCA cable 0.5m pair REAN (Neutrik) RCA plug This is a standard BELDEN line cable that clearly outlines the sound while having a firm thickness, especially in the mid to low range (Fujisawa Yukishi)
Maintenance information: 2024.4.16 continuity confirmed
Accessories: No accessories
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an unprocessed 1.7 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: none
The price has been drastically reduced. 2023/11/26 Sales price 128,000 yen Maintained in 2022/6! An eye-catching power amplifier with its black and large power meter typical of Sansui. It entertains me with its power, which can be felt from its appearance, and its supple, stretchy sound quality. The exterior has dullness, scratches, rust, etc. over time (Oikawa Tetsuji)
Maintenance information: 2022.6.23 Maintained (both channel volumes replaced. SP relay bad contact replacement. Replace protectors, deteriorated transistors, resistors, and diodes in meter boards. Replace deteriorated transistors and resistors in the power supply board. Replace deteriorated transistors and capacitors in the drive board. OUTPUT selector switch cleaning. (General adjustment)
Accessories: none
Main specifications: left and right independent 2 power supply diamond differential circuit effective output 110W+110W (8Ω) load impedance 4 to 16 ohms W482 x H187 x D450 mm 20.3 kg
The original appeal of Arden, where a simple and beautiful design and deep sound coexist, has been revived due to full internal and external maintenance utilizing the original capacitors. This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. The sense of scale of the orchestra and the smooth playback of stringed instruments are satisfying enough to listen to. There are repair marks on the edge of the cone paper on one side and the top surface on one side. The exterior has been beautifully finished due to exterior maintenance. Serial 0016190/0005927 (Murakoshi Yoichi)
Maintenance information: 2024.4.3 maintenance (exterior repair) 2022.5.30 maintained (output terminal contact cleaning. Chassis screw replacement. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (low range side: edge replacement, magnetic circuit rust removal/gap cleaning/center adjustment, high range side: magnetic circuit rust removal/gap cleaning/center adjustment. Exterior repair/polishing/oil finish Front and rear baffles/hakama repair/painting Saran net replacement. (Detachable unit)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
※The veneer is peeling, the top plate is undulating, and the grill is indented, so it is inexpensive. This high CP model was released in the 49th year of Diatone's founding. It has a very well-balanced, rounded, and gentle tone. I can do everything from jazz and rock to classical and pop music as an all-rounder (Oikawa Tetsuji)
Maintenance information: 2024.4.15 Operation confirmed
Accessories: none
Main specifications: 3 way 3 speakers, 6.3 ohms, sound pressure level, 90 dB, W380 x H680 x D295 mm, weight 25 kg
※Inexpensive because it smells like tobacco and is in poor condition. PSE certified product. A popular 6-prong power strip. The metal case has excellent rigidity and shielding, and Belden OFHC material is used for internal wiring. This best-selling model is popular for its thick sound image and ease of use. There is a strong feeling of use on the exterior, dirt, paint peeling, rust, etc. on the entire exterior (Murakoshi Yoichi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: none
Main specifications: 3P type x 2, 2P type x 4 ports, cable length 2 m
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 1.0 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.6 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.5 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
The price has been reduced! 2024/2/23 sales price 29,800 yen Manufacturer maintained! Phono motors only. It is a model that is responsible for Denon's volume zone, and rotation is controlled by a voltage support system that controls the AC power supply voltage of the same motor as the office unit. It has a reputation for its highly accurate rotation and smooth sound quality. There are threads and dullness throughout the exterior. Serial 9970 (Hiroki Aso)
Maintenance Information: 2024.2.23 Maintained (head gap adjustment leaf SW cleaning speed adjustment)
Accessories: copy of instruction manual
Main specifications: Servo-type direct drive Dimensions W370 x H139 x D374 mm Weight 6.7 kg
Balance cable 3.9 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range. The printing on the sheath has disappeared and there are seal marks on the plug shell (Kojima Yosuke)
Accessories: none
Balance cable 4.9 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range. The sheath printing disappears a lot (Kojima Yosuke)
Accessories: none
Balance cable 4.0m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range. There is dullness around the plug (Kojima Yosuke)
Accessories: none
Balance cable 3.9 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range. The printing on the sheath has disappeared and there are seal marks on the plug shell (Kojima Yosuke)
Accessories: none
Maintained by the manufacturer! Compact belt drive CD player. The D/A converter section is a dual mono configuration equipped with 2 units of the latest Barbrown PCM1792 (192 kHz/24 bit) independently on the left and right. The drive method unique to CEC contributes to the smoothness of the sound. The exterior is dull. Serial T53Z081.2004406 (Fujisawa Yukishi)
Maintenance information: 2024.4.13 manufacturer maintained (pickup, spindle belt replacement, Assy shaft disassembly and cleaning, grease up, confirmation of regeneration operation on an inspection disc)
Accessories: remote control, power cord, stabilizer
Main specifications: analog output: 1 unbalanced and balanced system, digital output: TOS, 1 coaxial, AES/EBU system each W217.5 x D448 x H111 mm approx. 7.2 kg
Speaker cable 2.0m pair A standard BELDEN speaker cable nicknamed “sea snake” with untreated terminals. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
The price has been reduced. 2024/4/11 sales price 278,000 yen ※Saran net is out of stock. Edge has been maintained, including a brand new replacement! It is an improved model of the best-selling S3100, and inherits the technical know-how of the K2 series. The compression driver is 275 Nd, and the high range horn is equipped with a defined directivity horn. The woofer uses the ME150HS. In addition to the loud, voluminous bass, the clear high frequency, which is sharper than the original, is attractive. There is color burn on the center cap, dents and small scratches on the top surface. (MURAKOSHI Yoichi)
Maintenance information: 2024.4.10 maintenance (exterior cleaning/simple repair
Woofer edge replacement, driver maintenance (magnetic circuit gap cleaning/center adjustment, sound absorbing material replacement, replacement with a used product of the same type due to damage to one side+ terminal) unit detachment/9V battery replacement)
Accessories: instruction manual
Main specifications: 2 way 2 speaker usage unit/38cm woofer ME150HS, horn H2600-1, HF driver 275nd efficiency 95dB impedance 8 ohms dimensions W561 x H1102 x D406 mm weight 63.5 kg/bottle
The price has been reduced. 2024/3/20 sales price 10,000 yen*Since there are many scratches such as scratches on the top plate and sides, and dents on the corners, it is inexpensive and is currently sold. Technics 3-way bookshelf speaker A honeycomb flat unit is used to reproduce a unique sound field feeling. In addition to the appearance described above, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.3.19 Operation confirmed
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex 6Ω 89dB crossover frequency 2kHz, 4.5kHz W223 x H378 x D207 mm 5.3 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/3/12 sales price 39,800 yen Manufacturer maintained! Phono motors only. It is a model that is responsible for Denon's volume zone, and rotation is controlled by a voltage support system that controls the AC power supply voltage of the same motor as the office unit. It has a reputation for its highly accurate rotation and smooth sound quality. Appearance, tobacco smell, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.3.12 Maintained (transistor, capacitor replacement, adjustment)
Accessories: transport lock screw
Main specifications: Servo-type direct drive Dimensions W370 x H139 x D374 mm Weight 6.7 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/12/19 sales price 39,800 yen Manufacturer maintenance completed. Phono motors only. It is a model that is responsible for Denon's volume zone, and rotation is controlled by a voltage support system that controls the AC power supply voltage of the same motor as the office unit. It has a reputation for its highly accurate rotation and smooth sound quality. Exterior, dullness, paint peeling, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.12.19 Maintained (transistor, capacitor replacement, servo adjustment)
Accessories: none
Main specifications: Servo-type direct drive Dimensions W370 x H139 x D374 mm Weight 6.7 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/3/1 sales price 138,000 yen A rare wooden sand-filled horn from Onken (Onken). The construction is very careful and the material is moderately soft, so it is very expressive. When combined with the OS-500MT, you can enjoy a warm sound. There is a feeling of use such as scratches and paint peeling (Takasaki Atsushi)
Accessories: none
Main Specifications: Wooden Sectoral Horn Metal Throat Recommended Usage Frequency Band 500 to 25,000 Hz Compatible Unit OS-500MT W560 x H250 x D420 mm 6.82 kg
Woofer edge softening treatment was completed in March 2021! The sharp mid-high range, which is typical of a diamond tone, is characteristic. The low frequency thickness unique to 30 cm is also attractive, so you can enjoy it in all genres. There are some dents on the exterior. Serial 16747/16900 (Yonejima Satoshi)
Maintenance information: 2021.3.6 Maintained (softened)
Accessories: saran net
Main specifications: 3 way 3 speaker sealed impedance 6 Ω playback frequency band 35 Hz-35 kHz crossover 500 Hz/4 kHz maximum input 230 W sound pressure 91 dB W380 x H680 x D325 mm 27 kg
Nagaoka record cleaner. High-density velvet fits the sound groove of the record board and removes dirt. As for the exterior, there are dirt and scratches on the case (Tomoho Asae)
Main specifications: body dimensions W115 x D42 x H35 mm 40 g (actual measurement)
Maintained! 100V specification genuine Baes product. A power amplifier representing the golden age of McKinn. It has a rich, gorgeous sound with a punch, and is still a popular model. Although it is a transistor amplifier, it is an amplifier that still has a strong tubular atmosphere. The rich, thick characters reproduce the music on a rich scale. Rust can be seen on the main body. Serial JCT2411 (Fujisawa Yukishi)
Maintenance information: 2024.4.8 Maintained (meter and display lamp replacement (there is slight unevenness in characters due to deterioration of the light guide plate, but this is the current situation) Electrolytic capacitor, rotary SW replacement. Apply heat-resistant tape. Solder correction. Clean card edge contacts, switches, and volumes. Possible panel peeling correction. Bias and offset checks. Output audio check)
Accessories: No accessories
Main specifications: 250W+250W (stereo 1/2/4/8Ω) 500W (mono 0.5/1/2/4/8/16Ω) input sensitivity (0.75V/2.5V) switchable W411 x H181 x D368 mm 37.2kg
Speaker cable A standard cable that has become synonymous with 1.4 meter pairs of unprocessed speaker cables. It features a stranded wire structure that enables reliable transmission with low noise even in harsh environments such as studios. Monitor-like sound quality with little coloring (Kobayashi Hitoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: none
Speaker cable A standard cable that has become synonymous with 0.95m pair end unprocessed speaker cable. It features a stranded wire structure that enables reliable transmission with low noise even in harsh environments such as studios. Monitor-like sound quality with little coloring (Kobayashi Hitoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: none
Speaker cable A standard cable that has become synonymous with an unprocessed speaker cable with an 0.8 meter pair end. It features a stranded wire structure that enables reliable transmission with low noise even in harsh environments such as studios. Monitor-like sound quality with little coloring (Kobayashi Hitoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: none
Speaker cable A standard cable that has become synonymous with an unprocessed speaker cable with an 0.8 meter pair end. It features a stranded wire structure that enables reliable transmission with low noise even in harsh environments such as studios. Monitor-like sound quality with little coloring (Kobayashi Hitoshi)
Maintenance information: 2024.4.7 continuity confirmed
Accessories: none