The deteriorated vacuum tubes etc. were replaced in 2023 and full maintenance has been completed! The vintage MC30 is still loved today, half a century later. The sharp high range and thick low to mid range sound are nothing short of wonderful. Since the left and right sides come out clearly without interference, you can feel a better sense of localization than a stereo machine. The good separation unique to mono amplifiers stands out, and it can play everything from jazz to classical music well (Murakoshi Yoichi)
Maintenance information: 2023.6.10 maintained (vacuum tube socket re-caulking repair, vacuum tube 12AX7 replacement, selenium countermeasure diode addition, 2W and 1/2W resistor replacement, HUM ADJ. readjustment/RCA jack re-caulking repair, operation check (measured at 25-38W SP:8Ω with rated output AC100-117 V).)
2012.6.12 Maintained (Capacitor Exchange/Mallory x 2, Sprag x 2, Europe x 2, Black Beauty x 10, Cornell x 2, Vacuum Tube, Partially Replaced with Good, Used, Silicon Rectifier, Vacuum Tube Pin, Rust Polishing and Socket Electrode Sack, Bolum, Sliding Surface Cleaning, RCA Pin Jack Cleaning, Each Voltage, Operation Inspection)
Accessories: none
Main specifications: rated output 30W, input sensitivity 0.5V vacuum tubes 6L6GC x 2, 5U4 x 1, 12AX7 x 2, 12BH7 x 1, 12AU7 x 1, W356 x H203 x D203 mm, weight 15.8 kg
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Line transformer using TANGO's input transformer, NN-600-600. The overall sound resolution is increased, and the sense of sound pressure is also enhanced. Recommended for those using speakers with horn drivers. TANGO badges are discolored, and there are tape marks and bumps on the chassis (Kojima Yosuke)
Maintenance information: 2024.4.18 Operation confirmed
Accessories: none
Main specifications: primary impedance 600 Ω (150 Ω split) secondary impedance 600 KΩ (150 kΩ split) primary inductance 70 H W140 × H110 × D100 mm 1.8 kg (actual measurement, not including protrusions)
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
RCA cable 1.0 m pair with 24K gold-plated turbine plug and split center pin specification, 2-core structure, sheath resistant to aging, and Duraflex jacket. The exterior has a feeling of use and dullness (Tomoho Asae)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
RCA cable 1.5m pair rhodium plated plug accuphase genuine OFC series cable looks like a high-purity OFC Ritz cable with excellent corrosion resistance, and it sounds supple at the same time as extrusion in the mid to low range. The exterior has a feeling of use such as rubbing, dirt, and bending habits on the sheath (Asaine Tomoho)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
Please upgrade to an RCA cable, 1.0 m pair, or Monster Cable standard cable from the original one. There is dullness etc. on the exterior (Tomonori Asae)
Maintenance information: 2024.4.18 continuity confirmed
Accessories: none
The price has been drastically reduced. 2024/1/13 sale price 99,800 yen rare Gauss 46cm woofer! This is the first model to arrive at Hi-Fi. Unlike JBL woofers, it is characterized by sound tightness and strength of extrusion. It also seems interesting to use it as a 4345 woofer (Sasaki Shota)
Main specifications: Ferrite magnet 46cm woofer impedance 8Ω (measured DC resistance value 6.3Ω, 6.0Ω) 8.7kg (actual measurement)
※It has a cigarette smell, so it's cheap. Compared to the 1.0 m pair of RCA cables, EQI6, OCC high-purity copper conductors, up to Equinox 5, the company's standard cable, which has a high level of clarity and creates a high-end oriented sound, is recommended as a first step towards luxury cables. There is a feeling of use due to appearance, dullness, friction, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.15 continuity confirmed
Accessories: none
Sennheiser Recable 1.5m Recable cable that can be used with 2PIN type headphones such as HD650. It's a stereo mini plug and the standard conversion plug is out of stock (Murakoshi Yoichi)
Maintenance information: 2024.4.15 continuity confirmed
Accessories: none
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/15 sales price 79,800 yen Maintained! JBL professional 2 inch screwdriver It is an item that continues to be used today in large horn systems, etc. The quality unique to titanium diaphragms makes the vocal breathing, drum hi-hat, and outstanding realism no matter which one you take. The exterior has dullness, scratches, rust, etc. due to use over time. Serial 53400 63923 (Tomonori Asaine)
Maintenance information: 2023.12.15 Maintained (diaphragm installation adjustment throat cleaning DCR 63923/8,3 ohm, no vibration damage
(DCR 53400/7.8Ω vibration has scratches and small dents)
Main specifications: throat diameter 5 cm; allowable input: 100 W; sound pressure level: 111 dB/w/m; frequency characteristics: 500 Hz to 20 kHz; crossover frequency: 500 Hz or more; 16 ohms; diameter: 235 x depth: 132 mm; 13.6 kg/1
Maintained! Genuine Electri A stainless steel chassis version of the 2nd generation reprinted model. It is a model that stands out for its good SNR feel and improved fine particle feel, etc., and its depth of pocket that is compatible with the latest sources is attractive. The heavy, vintage look is also wonderful. There are small transformer scratches on the exterior and many disappearing characters on the back. Serial JE10260 (Yonejima Satoshi)
Maintenance information: 2024.4.17 Maintained (The remodeled part has been restored to a state close to its original state. Since the electrolytic condenser liquid leak replacement shield case is out of stock, the additional guide pin was damaged, so create and paste a sticker with the missing letter in the hakama replacement character. Output audio check)
Accessories: No accessories
Main specifications: 6550 push-pull input 2 systems (XLR/RCA) rated output 75W+75W (4/8/16Ω) mono 150W (2/4/8Ω) W406 x H190 x D305 mm 30.5 kg
Full maintenance from the unit, network, and exterior! A floor-type speaker full of furniture that uses plenty of walnut wood. A powerful Alnico magnet is used for the 38cm unit, and the synergistic effect with the cabinet makes the mid-high range fresh and dynamic sound. It is also attractive that the connection up to the high range is smooth (Kobayashi Hitoshi)
Maintenance information: 2024.4.17 Maintained (exterior repair/polishing/oil finish, saran net replacement, unit maintenance: low range side: edge replacement, magnetic circuit gap cleaning/center adjustment, high range side: magnetic circuit gap cleaning/center adjustment. Network maintenance: frequency characteristic check, ATT contact cleaning, terminal cleaning)
Accessories: saran net, key
Main specifications: 15 inch coaxial 2-way 3889 (AlcomaXLLL) efficiency 93 dB allowable input 150 W continuous input impedance 8 ohms frequency characteristics/28 Hz to 22 kHz internal volume 235 liters W705 x H1,110 x D480 mm 68 kg
This model commemorates the 250th anniversary of J.S. Bach's death. Uses a 6N silver wire coil. It is a cartridge that excels in even more delicate spatial expression while retaining the feel of an orthophone. The know-how of the masterpiece Jupiter has been fully introduced, and the high cost performance stands out. The cantilever is moving slightly to the right (Tamura Eiji)
Maintenance information: 2024.4.17 operation confirmed
Accessories: original box, needle cover
Main specifications: output voltage 0.45 mV frequency characteristics 20 Hz to 35 kHz internal resistance value 5 ohms, suitable elliptical needle pressure 2.5 g, dead weight 10 g
*Currently sold. Fidelity-Research's standard model for light needle pressure. The simple design is also beautiful, and you can enjoy high-quality analog sound at an affordable price.
Accessories: none
Main specifications: static balance type short arm, effective length 245 mm, needle pressure range 0 to 3 g
Maintained! Comes with stand (DK-8000). A model that has improved the network box of the Diaton 50th anniversary model DS-8000. I am overwhelmed by the clear, detailed treble from Pure Boron and the thick mid-low range compared to the 2S-305 broadcast monitor. Also, the quick start-up sound, which is unimaginable from its size, is excellent. There is a feeling of use in appearance, dullness, light scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 2022.10.21 maintained (exterior stand network exterior cleaning/large scratch filler repair/line scratch simple touch up (repair marks remain) saran net stain/frame cleaning mid-edge softening treatment unit detachable one-sided tweeter disassembly and disconnection repair)
Accessories: saran net
Main specifications: 3 way, 3 speakers, bass reflex system, floor type, anti-magnetic type, 5 ohm 35 Hz to 40,000 Hz 93 db/w/m main unit W500 x H870 x D442 mm network box W370 x H130 x D287 mm weight body 58 kg, network 8 kg
The price has been reduced. 2024/4/16 Sales price 198,000 yen Edge softening treatment, etc. Maintenance completed! Comes with a 7.5 kg DK-2000Z stand dedicated to the DK-2000Z class weight! The DS-2000Z thoroughly sought realistic sound. The sound quality is beautiful and glittering, conveying even the feeling of air with sound. Please try the high resolution sound source. There is a feeling of use due to appearance, dullness, light scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 204.4.16 maintenance completed (exterior veneer float repair/cleaning, saran net replacement, woofer edge softening treatment)
Accessories: instruction manual, saran net
Main specifications: 3-way sealed system, bookshelf type speaker impedance 6 ohms playback frequency band 27 Hz to 80000 Hz output sound pressure level 90 dB maximum input 180 W dimensions W380 x H725 x D315 mm (356 mm with net) weight 37 kg stand dimensions W380 x H170 x D315 mm weight 27.5 kg
*Currently sold. Remote control is missing. A slim, space-saving FM/AM synthesizer tuner. Equipped with a 40-station memory function, it is a standard machine that is easy to use. The exterior is dull and has a feeling of use (Daiki Goto)
Maintenance information: 2024.4.3 operation confirmed
Accessories: power cable, instruction manual
Main specifications: FM/AM tuner W434 x H75 x D242 mm 2.5 kg
The price has been drastically reduced. 2024/4/10 sales price 450,000 yen The output tube has been replaced with a GE 6550! Genuine Electri A stainless steel chassis version of the 2nd generation reprinted model. It is a model that stands out for its good SNR feel and improved fine particle feel, etc., and its depth of pocket that is compatible with the latest sources is attractive. The heavy, vintage look is also wonderful. The hood is missing, there are many transformer paint peeling repair marks on the exterior, and the letters on the back have disappeared. Serial E10122 (Murakoshi Yoichi)
Maintenance information: 2017.10.18 Maintained (SW/VR disassembly contacts repolished, oxidized/vulcanized grease coated. Replace all 9P socket pins Voltage check for each part, check input/output waveforms, load test (at 1kHz, 8Ω load: 75W x 2) sound output test)
Accessories: instruction manual (copy)
Main specifications: 6550 push-pull input 2 systems (XLR/RCA) rated output 75W+75W (4/8/16Ω) mono 150W (2/4/8Ω) W406 x H190 x D305 mm 30.5 kg
The disposal price has been reduced. Member prices are not applicable. 2023/5/13 sales price 250,000 yen*The main volume, BASS, and TREBLE knob textures are different from the original. Internal parts have been thoroughly reviewed and maintenance has been carried out! This is a control amplifier from Sony's high-end brand, the Esprit series. Straight sound with a sense of speed similar to the TA-E900. The outline is clear and the sound image is drawn clearly. It is a vintage speaker and is especially recommended for jazz and rock fans. On the exterior, in addition to dullness and small scratches, there is a feeling of use, such as sticker marks on the top plate. Serial 200616 (Hiroki Aso)
Maintenance information: 2023.3.4 maintained (running test by refining the I/O board and screw parts) 2022.10.1 maintained (condenser semi-fixed resistance relay LED lamp IC spark killer Capricorn washer replacement implementation all SW VR disassembly cleaning board solder surface re-solder input/output waveform confirmation and left and right balance confirmation comprehensive operation test)
Accessories: copy of instruction manual
Main specifications: 2 PHONO inputs, 5 line inputs, 2 pre-out systems, W480 x H105 x D465 mm, 12.5 kg
The disposal price has been reduced. Member prices are not applicable. 2023/9/13 sales price 2,980,000 yen Maintained with attention to details such as drivers and wiring! The Georgian 4 is attractive for its elaborate horn configuration and beautiful furniture-like design. It is a model with a built-in crispy horn, a structure that creates a unique sound with a rich sense of scale, and the loud sound is truly an American masterpiece, but you can also feel a somewhat English-like sex appeal. *The attenuator has been maintained, but slight chipping occurs when turning due to deterioration of the original winding resistance (Oikawa Tetsuji)
Maintenance information: 2023.9.13 Maintained (828HF disassembly and maintenance: separation from magnetic circuit and diaphragm, magnetic circuit diaphragm maintenance: cleaning of the magnetic circuit, rustproof vibration system, round out, stop noise, T350 disassembly and maintenance: separation from the magnetic circuit and diaphragm, sound pressure difference adjustment: stop noise due to resonance sound generation, elimination of sound pressure drop due to rear sound leakage. Confirm that there are no modifications inside the housing. Remove rust from screws on screw-type terminals, pickle, and polish and clean the receiving side. ATT (x4) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: none
Main specifications: 4-way 15WK, 828HF, T350, X336 (300/3500) approx. W860 x D660 x H1,350 mm approx. 90 kg
Comes with a stand. JBL professional tweeters. Since it is designed to make the sound fly far, the sound quality is solid and more straight compared to the company's consumer model 077. The mid to high frequencies are vivid, and the low frequencies are finished with a tight sound. There is a feeling of use such as dullness and slight scratches over time (Yamato Yuki)
Maintenance information: 2024.4.16 sweep test good
Accessories: stand
Main specifications: horn type tweeter impedance 16 ohms playback frequency band 6,500 to 21,500 Hz (manufacturer specified), crossover 7 kHz, efficiency 105 dB, W100 x D84 mm, 3 kg/book (stand not included)
Balance cable 0.7 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound yet has a firm thickness in the mid to low range. The printing on the sheath has disappeared (Kojima Yosuke)
Accessories: none
Balance cable 0.6 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
Balance cable 0.6 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
Balance cable 0.5 m Peer Noitric plug is a standard BELDEN line cable that clearly outlines the sound while also having a firm thickness in the mid to low range (Kojima Yosuke)
Accessories: none
※Only 1 balance cable is 9.9m. This is a standard BELDEN line cable with a firm outline of the Neutrik plug sound, yet has a particularly firm thickness in the mid to low range. The printing on the sheath part has disappeared (Kojima Yosuke)
Accessories: none
※Only 1 balance cable is 4.9m. This is a standard BELDEN line cable with a firm outline of the Neutrik plug sound while also having a firm thickness in the mid to low range. The printing on the sheath part often disappears (Kojima Yosuke)
Accessories: none
※Only 1 balance cable, 4.9m, is a standard BELDEN line cable with a firm outline of the Neutrik plug sound while having a firm thickness in the mid to low range. The printing on the sheath part has disappeared and there are seal marks on the plug shell (Kojima Yosuke)
Accessories: none
* No. 3 hot specification RCA-XLR conversion cable, 3.9 m pair, both end plugs are a standard BELDEN line cable that clearly shows the outline of Neutrik's sound yet has a firm thickness, especially in the mid to low range. The sheath printing disappears a lot (Kojima Yosuke)
Accessories: none
※It has a cigarette smell, so it's cheap. Currently sold. 115V specification A German stereo power amplifier with resolution and expressiveness not typical of commercial use. It is proud of its exhilarating sound and outstanding driving power that comes out quickly. The exterior has scratches and paint bald spots. Serial 2172380UGD01107 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 85W+85W (8Ω) 150W+150W (4Ω) W483 x H88 x D270 mm 11.5 kg
RCA cable 0.5m pair REAN (Neutrik) RCA plug This is a standard BELDEN line cable that clearly outlines the sound while having a firm thickness, especially in the mid to low range (Fujisawa Yukishi)
Maintenance information: 2024.4.16 continuity confirmed
Accessories: No accessories
RCA cable 0.5m pair REAN (Neutrik) RCA plug This is a standard BELDEN line cable that clearly outlines the sound while having a firm thickness, especially in the mid to low range (Fujisawa Yukishi)
Maintenance information: 2024.4.16 continuity confirmed
Accessories: No accessories
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an unprocessed 1.7 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: none
The original appeal of Arden, where a simple and beautiful design and deep sound coexist, has been revived due to full internal and external maintenance utilizing the original capacitors. This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. The sense of scale of the orchestra and the smooth playback of stringed instruments are satisfying enough to listen to. There are repair marks on the edge of the cone paper on one side and the top surface on one side. The exterior has been beautifully finished due to exterior maintenance. Serial 0016190/0005927 (Murakoshi Yoichi)
Maintenance information: 2024.4.3 maintenance (exterior repair) 2022.5.30 maintained (output terminal contact cleaning. Chassis screw replacement. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (low range side: edge replacement, magnetic circuit rust removal/gap cleaning/center adjustment, high range side: magnetic circuit rust removal/gap cleaning/center adjustment. Exterior repair/polishing/oil finish Front and rear baffles/hakama repair/painting Saran net replacement. (Detachable unit)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Set of 4 This stand is made of high-carbon cast iron with excellent vibration handling capabilities. It can be used for a wide range of speakers from large to medium. The sound image is accurately and tightly reproduced. The exterior is dull and has small scratches (Murakoshi Yoichi)
Accessories: none
Main specifications: W100×H140×D300mm high carbon cast iron Weight 8kg/book
The disposal price has been reduced. 2024/4/4 sales price 473,000 yen Full maintenance from the driver to the woofer, from the network to all exterior repairs and paint! The outstanding vocal band and the sense of energy of the resonating horn are amazing. The current network is a rare N-500D. The sound of the driver resonates more quickly than the 800 Hz model, and it feels better. (Sasaki Shota)
Maintenance information: 2024.4.4 Maintained (exterior repair/full painting. Horn cleaning/touch repair, new horn receiver created. Woofer maintenance: viscoid adjustment/center adjustment, terminal cleaning. Driver maintenance: magnetic circuit in-gap cleaning center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, terminal contact cleaning)
Accessories: none
Main specifications: enclosure 825 woofer 416A driver 802D network N-500D horn 511B W760 x H1375 x D610 mm weight approx. 73.9 kg
The price has been drastically reduced. 2024/4/19 sales price 398,000 yen Restored in 2018! The HPD385 is mounted on the domestically produced box Recutangular York. The balance between the 15-inch unit and enclosure volume is excellent, bringing out the appeal of any source. There is no habit in low frequencies with a sense of volume, and it responds smoothly even to delicate high frequencies (Kojima Yosuke)
Maintenance Information: 2018.5.1 Maintained (unit edge replacement. Magnetic circuit slit interior cleaning, center adjustment exterior polishing. Replace the input terminal with a banana terminal compatible product. Output terminal polish cleaning. Faston terminal replacement. ATT cleaning. Check the input/output waveform and balance, and check the sound output. Frequency characteristics were measured and the original capacitors were continuously used because the results were good. Clear exterior finish, rear baffle paint Saran net cleaning, reupholstering)
Accessories: none
Main specifications: 2-way coaxial speaker, equipped with HPD385, 92dB, 8Ω, W611 x H1083 x D410 mm, weight approx. 57 kg/book
The disposal price has been reduced! (Member prices are not applicable) 2024/4/2 sales price 79,800 yen Hi-Fi Hall first arrival! A compact and elegant DALI tall boy speaker with sharp low frequencies and clear midrange, and an airy treble range. The exterior has a scratch on the stand, a scratch on the side of the main unit, and a small scratch on the top plate. Serial 6255811 (Sato Wataru)
Maintenance information: 2024.4.2 sweep test good
Accessories: instruction manual, spike, saran net
Main Specifications: Frequency Characteristics: 39~26kHz 88dB Impedance 4Ω Tweeter 29mm Soft Dome Midrange/Woofer 130mm/SMC Wood Fiber Cone Driver ✕ 2 Dimensions W162 ✕ D283 ✕ H830mm Weight 10.8 kg
The price has been reduced! 2024/4/12 sales price 70,000 yen B&W 805D series speaker stand. Equipped with a spike insulator “T-PROP”. It is a speaker stand with a completely new concept developed with the theme of eliminating speaker stress as much as possible by absorbing and releasing it in a natural way without putting a load on the diamond formation structure. The exterior has scratches, paint peeling, and bumps. (FUJISAWA KOSHI)
Accessories: insulator T-PROP, screws
Main specifications: top plate W227 x D306 mm B&W 805 Diamond, D3 specially designed bottom plate W280 x D360 mm height 500 mm approx. 15 kg
1.2 m PSE standard power cable A popular cable that combines the elements necessary for a power cable, such as transparency, power, and speed, at a high level, and matches any device. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: original box
Technica MC Cartridges. The sound quality is bright and precise, and the sharpness of the high frequencies is excellent. It is sharper than the 33 derivative models that followed, and fits well with jazz fusion (Oikawa Tetsuji)
Maintenance information: 2024.4.14 Operation confirmed
Accessories: none
Main specifications: output voltage 0.4 mV needle pressure 1.2 to 1.8 g (standard 1.5 g) internal impedance 17 ohms oval needle weight 6.8 g
1.8 m PSE standard power cable, 4 types of hybrid original conductor+3-core structure, this is a long-selling cable that reproduces a sense of expanding sound field, medium to high range with good coverage, and a wide range. (FUJISAWA KOSHI)
Maintenance information: 2024.4.14 continuity confirmed
Accessories: original box
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 1.0 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.6 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
Speaker cable A standard BELDEN speaker cable nicknamed “sea snake” with an untreated 0.5 m pair end. The cable braided in orange and black is impressive, and it features a tight sound. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.13 continuity confirmed
Accessories: none
The price has been reduced. 2024/3/24 sales price 59,800 yen digital cable 1.5m BNC specification In order to comply with next-generation standards, a large diameter variclad core with about twice the capacity of regular products is adopted, and large amounts of information can be transmitted at high speed. The sound is high speed and has excellent sharpness. There are abrasions around the tube (Kojima Yosuke)
Accessories: none
The price has been reduced. 2024/4/2 sales price 12,800 yen current orthophone cartridge. 6mV high output! It is resistant to scratches, backspins, etc., and boasts high followability (Daiki Goto)
Maintenance information: 2024.4.2 continuity confirmed
Accessories: original box
Main specifications: 6 mV frequency characteristics 20 Hz to 20,000 Hz -2 dB/+4 dB recommended load capacity value 200-600 pF needle pressure 4 g dead weight 6.5 g
The price has been reduced. 2024/4/6 sales price 50,000 yen The depth, positioning, reverberation, and sense of distance are improved compared to the original top plate using high-purity oxygen-free copper (OFC4N 99.99%) for P-0s ※ The top plate screws require longer screws, but they are not included. Please be careful (Daiki Goto)
Maintenance information: ※ Longer top plate screws are required, but they are not included. Since preparations are not possible, the person who purchased it will have them ready. Please be careful.
Accessories: none
Main specifications: thickness 12 mm, measured 13.3 kg