Internal and external maintenance has been applied and brushed up! JBL 40th anniversary model! A reprint model of the L101. You can enjoy the excellent sound unique to horn drivers. It has a good response and is a spacious speaker that can be matched with music of a wide range of ages. The traditional lattice net design is also attractive. There is slight discoloration on the marble (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (exterior repair/polishing/oil finish
Front and rear baffles/hakama repair/painting. Lattice repair/polishing/painting, lining replacement. Woofer edge replacement. Driver maintenance (magnetic circuit gap cleaning center adjustment). Network maintenance (frequency characteristic check, ATT cleaning).)
Accessories: lattice
Main specifications: 2 way · 2 speakers · bass reflex system · floor type frequency characteristics 35 Hz to 16,000 Hz directional characteristics (horizontal x vertical) 90 degrees x 40 degrees sound pressure level 92 dB 8 Ω allowable input 150 W crossover frequency 900 Hz enclosure volume 53.5 L W445 x H629 x D320 mm 29.1 kg/book
Full maintenance from each unit to network and exterior! This is a 4343BWX with blue baffles and walnut specifications. The instantaneous power, sharp treble, volume and dynamism of the bass are outstanding. It's one step ahead of current speakers in terms of localization, but it's rare to find a speaker that makes on-mic recordings of all ages sound better than this. It has a beautiful finish due to exterior maintenance (Oikawa Tetsuji)
Maintenance information: 2024.5.27 Maintained (exterior repair/polishing/oil finish baffle repair/paint saran net repair/frame repair: edge replacement, cone paper coating, in-gap cleaning/center adjustment midmaintenance: edge replacement/cone paper coating driver maintenance: magnetic circuit rust removal/gap cleaning/center adjustment, sound absorbing material replacement, terminal cleaning/screw replacement Tweeter maintenance: magnetic circuit rust removal/gap cleaning, terminal cleaning/screw replacement network maintenance: frequency characteristic check, ATT/switching SW cleaning, partial defective resistance/capacitor replacement unit detachment/diffuser repair)
Accessories: none
Main specifications: 4-way monitor speaker bass reflex playback frequency band 35 Hz to 20 kHz (+- 3 dB) crossover frequency 300 Hz/1250 Hz/9500 Hz impedance 8 Ω output sound pressure level 93 dB dimensions W635 x H1,051 x D435 mm weight 83.9 kg
Fully maintained! 2-way floor speaker with a double woofer and 1 horn. With the benefit of the 2234H woofer, which has a fast response and is highly efficient, I have the impression that it is very easy to sound even though it is a double woofer. Coupled with the excellent penetration of the biladial horn, it develops a very energetic sound stage. The good positioning unique to 2WAY is also a good impression. It has a beautiful finish due to exterior maintenance (Oikawa Tetsuji)
Maintenance information: 2024.5.27 maintained (exterior repair/polishing/oil finish front and rear baffle/hakama/horn coating, saran net replacement driver maintenance: magnetic circuit gap cleaning/center adjustment, sound absorbing material replacement, terminal cleaning/screw replacement network maintenance: frequency characteristic check, ATT/switching SW cleaning, terminal cleaning/screw replacement unit detachment)
2023.12 Edge replaced
Accessories: none
Main specifications: 2 way 3 speaker bass reflex type [unit used] 38cm woofer/2234H x 2 driver/2421A+ biladial horn/2344 frequency characteristics 30Hz-16kHz impedance 8Ω sound pressure level 96dB allowable input 375W crossover frequency 1,000 Hz (30Hz to 1kHz on one side, 100Hz or less on the other) Dimensions W965 x H908 × D515mm weight 114 kg/1 bottle
This is a standard JBL monitor that has undergone internal and external maintenance and has been refreshed. The darker and thicker tone compared to the current model still doesn't even seem to be declining in popularity. The thick, exhilarating sound goes well with jazz and rock, and the punchy sound is captivating. The exterior has been beautifully finished due to maintenance. Serial 32547 32298 (Murakoshi Yoichi)
Maintenance information: 2024.5.16 maintenance (exterior repair/cleaning, saran net cleaning, repasting, ATT cleaning)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system frequency characteristics 45 Hz to 20 kHz sound pressure level 93 dB impedance 8 ohms allowable input 100 W dimensions W362 x H597 x D298 mm weight 20 kg/1
The price has been reduced! 2024/5/25 sales price 99,800 yen Maintained! Professional A version (8 ohm specification) of the LE15. This woofer has good response and allows you to enjoy a dry, tense sound. There is only one unit developed for monitors, and it is a unit that can handle large inputs. (YONEJIMA Satoshi)
Maintenance information: 2024.5.25 Maintained (edge replacement, operation check)
Accessories: No accessories
Main specifications: 38cm cone woofer Alnico 8Ω (measured DC value 7.0Ω/6.9Ω) 150W crossover 800Hz baffle opening diameter 355mm screw pitch (diagonal) 370 mm
Refresh yourself with interior and exterior maintenance! A gray-finish model of the king monitor 4343B. The balance between thick, strong mids and responsive bass is perfect. A model that wants to make jazz and rock sound thick, thick, and powerful. It's a lot of exhilarating noises. The exterior has been beautifully finished due to maintenance (Tomoho Asaine)
Maintenance information: 2024.5.27 Maintained (exterior repair/all coated saran frame processing correction repair/net replacement, plate maintenance repair, plate maintenance (edge replacement, cone paper coating, center cap replacement)) midmaintenance (edge replacement, cone paper coating, center cap replacement, driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound absorbing material replacement, terminal cleaning/screw replacement) Tweeter maintenance (magnetic circuit rust removal/gap cleaning, terminal cleaning/screw replacement, exterior painting) horn painting, diffuser repair/painting, baffle plate cleaning unit detachable network maintenance: frequency characteristic check, ATT cleaning, switching SW/terminal cleaning/screw replacement)
Accessories: diffuser saran net
Main specifications: 4 way 4 speaker bass reflex crossover 300 Hz/1,250 Hz/9,500 Hz impedance 8 Ω 93 dB dimensions W635 x H1,051 x D435 mm weight 83.9 kg/1
Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. There are some scratches on the diaphragm on one side. Serial 60878/74750 (Yonejima Satoshi)
Maintenance information: 2024.6.1 Maintained (diaphragm installation adjustment, pad dampener installation, screw rust replacement. Wiring terminal contact cleaning, terminal dirt cleaning. Insulating bushing replacement. Diaphragm dirt cleaning. DCR (29324/6Ω diaphragm undamaged) DCR (33387/5.8Ω diaphragm damaged)
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Maintained! This is a JBL mid to high range driver. It is also used in the S2600 and S3500, etc., and the well-balanced sound quality with both strength and subtlety is truly a JBL. It can be used on various systems with easy-to-use specs. The exterior has peeling paint, dullness, etc. Serial 041250 041277 (Yonejima Satoshi)
Maintenance information: 2024.6.1 maintained (diaphragm installation adjustment, pad dampener and screw connections OK. DCR (041250/3,4ohm diaphragm no scratch) DCR (041277/3,0ohm diaphragm no scratch))
Accessories: No accessories
Main Specifications: High Range Driver Throttle Diameter 25mm Impedance 8Ω Frequency Range 500Hz to 20kHz Pure Titanium Crossover Frequency 800Hz W147 x H147 x D105 mm 4.3 kg
The price has been reduced. 2024/5/25 sales price 99,800 yen with 2447 exclusive horn! A coherent wave structure is used for the phase plug. It is designed so that the phase plug can be connected directly to the horn throat. A titanium diaphragm is used. You can see the exterior, dullness, dirt, abrasions, etc. and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: stand
Main specifications: Throat diameter 3.8 cm 16 ohms Frequency characteristics: 500 Hz to 20 kHz
Maintained! The culmination of Paragon, late model D44000WXA. The design created by Arnold Wolff is of course undisputed, but Paragon is wonderfully well thought out when it comes to sound quality, and it transcends the line for audiophiles. The combination of the reverberation of each unit and the late enclosure is the final form Paragon aims for. The beautiful way of making a plump, floating sound is unique (Yamato Yuki)
Maintenance information: 2024.5.31 maintained (exterior cleaning/repair/gloss adjustment, horn paint black paint woofer back grill repair driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound absorbing material replacement, terminal cleaning/screw replacement) tweeter maintenance (magnetic circuit rust removal/gap cleaning, terminal cleaning/screw replacement) ATT cleaning unit detachable)
Accessories: none
Main specifications: D44000WXA low range 38cm cone type LE15H+ medium range horn type 376+H5038p+ high range horn type tweeter 075 network LX5+N7000 crossover 500Hz/7000 Hz impedance 8Ω output sound pressure level 96dB allowable input 125W size W2640 x H902 x D740 mm weight approx. 300 kg
The disposal price has been reduced. Member prices are not applicable. 2024/5/20 sales price 198,000 yen Kappa series improved model Renaissance 90. The mid-high range is composed of EMIM and EMIT special units, and the sound is extremely delicate and clear. The deep sound field space and glossy, moisturized mid to high frequencies are unique to ribbon units. It has high resolution throughout the entire range and is suitable for classical and vocal styles. There are small scratches and line wounds, and there are repair marks of broken decorative plates at the foot (Oikawa Tetsuji)
Maintenance information: 2013.12.15 Maintained (exterior repair and cleaning. (Back side urethane deteriorated, replaced with substitute urethane)
Accessories: spikes
Main specifications: 4 way 4 speakers sealed floor type EMIT tweeter EMIM mid-range ribbon type 87dB 4Ω 250W W435 x H1245 x D315 mm 35.8 kg
The price has been reduced. 2024/5/25 sales price 39,800 yen This is an S-shaped tonearm. You can use static balance cartridges with a dead weight of 15 to 22 g. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.22 continuity confirmed
Accessories: instruction manual, connection cord
Main specifications: static balance one-point cross suspension type, effective length 229 mm, applicable cartridge weight 4 to 12 mm
Hyphonic rare shell Made of hard aluminum alloy+gold plated brass, it has a luxurious appearance. The overhang can be adjusted using the slide method. The exterior is dull (Tomonori Asaine)
Maintenance information: 2024.6.1 continuity confirmed
Accessories: No accessories
Main specifications: Weight 13g (including lead wire)
Hamilex compact 4-tier rack. The design is simple and you won't get tired of it. The shelves can also be adjusted, making it easy to use. The screw holder on the reinforcing column rotates idle and the screw cannot be stopped completely. There are blows and scratches on the exterior (Murakoshi Yoichi)
Accessories: none
Main specifications: Top plate load capacity: 100 kg or less Shelf board load capacity 50 kg or less Bottom plate load capacity 100 kg or less Total load capacity 250 kg W591 x H600 x D550 mm Weight 31.5 kg
It is a grace shell characterized by a fin shape. Lightweight yet hard, highly rigid shell (Asaine Tomoho)
Maintenance information: 2024.6.2 continuity confirmed
Accessories: No accessories
Main specifications: carbon fiber dead weight 10.7g
The price has been reduced! 2023/5/9 sales price 39,800 yen This speaker is equipped with the AXIOM10 vintage unit. Early model with 16 ohms. You can enjoy bright vocals with a tasteful tone unique to vintage speakers. Please try playing it on a record. The exterior has dullness, small scratches, etc. (Satoshi Yonejima)
Maintenance information: 2024.5.9 sweep test good
Accessories: No accessories
Key Specifications: 25cm double cone full range unit 20W 15/16Ω
Hi-Fi's first Trilogue series subwoofer has arrived! Not only for those using the Trilogue speaker, it also demonstrates sufficient performance as a standalone unit. This one is not compatible with spikes. The exterior has dullness and scratches. Serial 30-07-00 (Tamura Eiji)
Maintenance information: 2024.5.30 Operation confirmed
Accessories: power cable, saran net, original box
Main specifications: built-in power amplifier, 2 speakers, bass reflex, built-in power amplifier output, 200W, high frequency cutoff frequency 40/50/60hz, W380 x H540 x D650 mm, weight 45 kg
Pair tube Russian reprint model lot: 1903/1903 measured value 52/50 (rejected value 44) side getters with original box have been reduced ※Pairs are judged based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Pair tube Russian reprint model lot: 1903/1902 measured value 54/48 (rejected value 44) with original box*Pairs are judged based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: original box
Special arm base for attaching the GLANTZ tonearm MH-1200S to the LUXMAN record player PD-191A. Attach it to the back left side of the PD-191A main unit. The exterior is generally good (Takahashi Nobuyuki)
Accessories: mounting screws
Main specifications: Material stainless steel W128 x H15 x D128 mm 787 g (actual measurement)
Hi-Fi is in stock for the first time! GLANTZ statically balanced tone arm. The main body is machined from hard stainless steel, and the structure is firmly supported by 4 large bearings, and it has high traceability performance with reduced resonance and blurring, and exudes a sharp sound. Since there is weight in the weight part, you can use heavy cartridges such as OrtoFon's SPU without lowering the weight too much. The exterior is generally good (Takahashi Nobuyuki)
Maintenance information: 2024.6.2 operation confirmed
Accessories: instruction manual, headshell, phono cable, cartridge installation screw wrench
Main specifications: Form Static balance system Total length 330 mm Effective length (arm fulcrum to needle tip) 305 mm Effective length (arm fulcrum to center of turntable) 290 mm Compatible cartridge 16 to 43 g weight 1.14 kg Overhang 15 mm Mounting base internal dimensions 16 mm Mounting hole 30 mm
The price has been reduced. 2024/6/1 sales price 118,000 yen popular 15 inch Alnico magnet HIFI woofer! The high efficiency and punchy, bouncy low frequencies are attractive. It is compatible with JBL drivers, and it is easy to create a sense of scale even in bass reflex type enclosures, etc. Mounting in an airtight or bass reflex enclosure with an internal volume of 150L to 250L is recommended. You can see the exterior, dullness, rust, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.6.1 operation confirmed
Accessories: none
Key Specifications: Alnico Magnet 38cm Impedance 8Ω Crossover Frequency 800Hz Sound Pressure 96.8dB Front Mount 357mm Rear Mount 349mm 11kg
Speaker cable 3.0 m/4.3 m pair end end uses a μ-conductor with unique processing applied to the PC-OCC conductor for the purpose of reproducing sound with good sharpness, and it is a cable with excellent cost performance that also achieves delicate high-frequency reproduction (Fujisawa Yukishi)
Maintenance information: 2024.5.31 continuity confirmed
Accessories: No accessories
The price has been drastically reduced! 2024/5/18 sales price 39,800 yen Flat speaker using 600 neodymium magnets. It is built into a self-made enclosure. It is an audio speaker that is mainly used outdoors for station announcements and as a large digital signage product for outdoor use. As for the exterior, there are screw holes in the top plate, and there are dullness and small scratches all over (Yonejima Satoshi)
Maintenance information: 2024.5.18 sweep test good
Accessories: No accessories
Main specifications: MCMA multi-cell flat speaker impedance 8Ω frequency specification 90Hz to 10kHz W270 x H375 x D205 mm 5.2 kg (actual measurement)
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/24 sales price 29,800 yen ※1 wooden horn is compatible not only with FOSTEX drivers, but also with JBL 1-inch drivers (stop 3 points). It is a horn characterized by a broad sound unique to wood horns, which is different from metal horns (Takahashi Nobuyuki)
Main specifications: cutoff frequency 420 Hz throat 2.54 cm birch wood parallel plywood W444 × H90 × D293 mm 3.1 kg (actual measurement)
It comes with a straight pipe, only a lightweight weight, and an external armrest, so it's inexpensive. Maintained! EXCLUSIVE's popular analog player. The inside of the thick cab is structured so that the motor part and tone arm part float. When you actually play it, the effect is tremendous, and it brings out the sound of the record to the extreme. The exterior is broken in the corner of the dust cover, chipped glass, and finger tips are substitutes, and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.6.2 maintenance completed (START, disassembly and cleaning in other buttons, servo circuit electrolytic capacitor replacement, rotation lock position adjustment, arm damping grease cleaning replacement, turntable height adjustment, armrest replacement (structure is different). (Arm operation, voice check)
Accessories: straight pipe, lightweight weight, instruction manual (copy)
Main specifications: linear torque DC Hall motor direct drive dynamic balance type arm needle pressure adjustment range 0 to 3 g W600 x H267 x D415 mm 45 kg
Machined aluminum headshell made by ENTRE. It has a standard shape, and the sound stretches and tightens well (Tomoho Asae)
Maintenance information: 2024.6.1 continuity confirmed
Accessories: none
Main specifications: dead weight approx. 13g
Machined aluminum headshell made by ENTRE. It has a standard shape, and the sound stretches and tightens well (Tomoho Asae)
Maintenance information: 2024.6.1 continuity confirmed
Accessories: none
Main specifications: dead weight approx. 13g
*50 Hz specification. Maintained! A new Studio Technik Dusch suspension on a glass turntable! Fonoico is also a nice setting at 155th in the Franz era. The sharpness, precision of contouring, and a very thick sound are just words. A world-class player who still grabs the hearts of many analog fans and never lets go. Enjoy sounds that can only be experienced with EMT. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.6.2 Maintained (930ST: motor detached/lubricated, adjusted. Replace deteriorated forward phase capacitors with new ones. Speed adjustment brake felt replacement Main bearing housing detachment, gasket replacement, bearing ball damage replacement, etc., sealant attachment assembly. Replace the motor bush with a new one that has deteriorated. Replace the deteriorated turntable anti-noise rubber belt with a new one. Replace the idler with a new one that has deteriorated. 155ST: Balance adjustment trimmer resistor defective replacement. NF gain adjustment trimmer resistor noise exchange. Foundation solder deterioration correction. audio measurements. SW/VR cleaning, coat processing. Left and right output adjustment. (Running test OK)
Accessories: power cord, manual (copy), oil, connection cable (1 pair each of XLR and RCA)
Main specifications: idler drive system aluminum die-cast turntable rotation speed 33 1/3, 45, 78 rpm W490 x H234 x D410 mm [tone arm EMT929] dynamic balance type needle pressure range 0 to 5 g [equalizer amplifier 155 st] frequency characteristics 40 Hz to 20,000 Hz input impedance 140 to 200 ohms output impedance 200 to 600 ohms [cartridge TSD-15 ] MC type output voltage 0.15 mV, proper needle pressure 2.5 g, impedance 24 ohms
In addition to full maintenance including the exterior in 2020, the ATT has now been cleaned and inspected all parts, and further brushed up. The Georgian 4, which has an attractive elaborate horn configuration and beautiful furniture-like design, has arrived. It has a structure with a built-in crispy horn to create a unique sound with a rich sense of scale. There is a smell in the room (Kobayashi Hitoshi)
Maintenance information: 2024.6.2 maintained (ATT cleaning/inspection of various parts) 2020.2.12 maintained ([main body] exterior cleaning/touch repair, resonance/distortion countermeasures, unit detachment [unit] single-sided woofer recorn, both driver disassembly and cleaning, TW one-sided disassembly and cleaning, TW single-side coil manufacturing exchange [network] TW capacitor and resistor replacement. *Some capacitors before replacement are difficult to remove, so they are left inside. Frequency characteristic measurement check (~ 42 kHz). Input/output waveform and balance check, sound output check.)
Accessories: none
Main specifications: 15WK, MT-30 (828HF), T35VHF, X336 (300/3500) approx. W860 x D660 x 1350 mm approx. 90 kg
※Since it is for commercial use and is inexpensive, it will be handed over as is. This is a PA speaker equipped with a 38cm woofer and compression driver. Unique to PA speakers, it is a powerful and straight sounding speaker with excellent response. There is a slight feeling of use, and there is a dent in the grill on one side (Daiki Goto)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: connection cable
Main specifications: 40Hz to 20kHz 8Ω 250W 100dB input terminal speakon W466 x H648 x D386 mm 20.9 kg
The price has been reduced. 2024/6/1 sales price 598,000 yen rare items have arrived! Swiss-made electro Voices It features a thick sound unique to wood horns, and tight low frequencies. The goodness of construction shines through. It is equipped with a laminated wood horn, and I want to raise the volume and make a sound. Please experience the natural tone of an acoustic guitar and the subdued sound of the wood bass. The exterior has scratches on the corner, paint chips on the back, and other overall line damage (Mizusaki Ryo)
Maintenance information: 2024.6.1 sound output confirmed
Accessories: none
Main specifications: Swiss 2 way 2 speakers, efficiency 93 dB, impedance 10 ohms, external dimensions W378 x H590 x D325 mm, weight: 28.5 kg
This is a PA speaker for EVs. You can enjoy a clean sound with crisp high frequencies and responsive low frequencies. It's made of resin and is lightweight, so it's easy to carry around. It can be used for a wide range of purposes, such as reeds at home and at events. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: none
Main specifications: 1 inch driver, 30 cm woofer impedance, 8 ohms, 300 W, 80 to 25,000 Hz, size W430 x H585 x D314 mm (actual measurement), 15.3 kg (actual measurement)
Pair tube direct heat triode tube, white base, made in Russia, measured value 80/80 (rejected value 58) with original box ※ pair is determined based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: original box
Pair tube direct heat triode tube, white base, made in Russia, measured value 84/76, rejected value 58) with replacement box ※Pairs are determined based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: replacement box
The price has been reduced! 2024/6/1 sales price 148,000 yen A center speaker that develops ELAC's new-generation quality into multi-channel. It can easily handle the latest multi-channel sources that require huge amounts of information from the center channel. The exterior has line scratches on the TW periphery and threads on the top plate. Serial 0614 (Yonejima Satoshi)
Maintenance information: 2024.6.1 sweep check is good
Accessories: saran net
Main specifications: center speaker, 2.5-way bass reflex, efficiency 89dB, impedance, 4Ω, frequency characteristics, 32 to 50,000 Hz, crossover frequency, 450/2,400 Hz, maximum input 160 W, W650 x H204 x D314 mm, weight 14 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/5/26 sales price 348,000 yen The current ELAC speakers have arrived! It firmly follows the merits of ELAC up until now, and shines with a higher degree of perfection than ever before. With an expanse that doesn't make you feel the presence of the speaker, and the sound is delicate and bright, it is a practical speaker regardless of genre. There is a small dent in the lower woofer on one side. Serial 31800E000053/31800E000056 (Takasaki Atsushi)
Maintenance information: 2024.5.25 sound output confirmed
Accessories: instruction manual, jumper, spike holder, original box (cushioning material partially broken)
Main specifications: 2.5-way bass reflex type crossover frequency 450/2400 Hz frequency characteristics 30 to 50,000 Hz efficiency 88 dB recommended amplifier power 40 to 300 W rated input 130 W impedance 4 ohms W229 ✕ H1,000 x D266 mm 19.1 kg
Maintained. DYNACO's tubular mono power amplifiers are highly popular. The sleek, straight, and energetic sound that comes out of the small body is attractive. Combinations with Altech and JBL are a staple, and they make jazz and rock sounds powerful and full of realism. You can see a feeling of use on the exterior, dullness, rust, scratches, etc. (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (board peeling and re-soldering treatment, block capacitor 30/20/20 μF replacement, film capacitor 0.047 μF → 0.1 μF original, electrolytic capacitor 50 μF, resistance 1W → 1/2 W original replacement, BIAS readjustment/RCA jack and vacuum tube socket caulking repair. Operation check) 2016.2.27 Maintained (AC cord, cord stopper, input terminal, capacitor (47uF100V) resistor (47k, 270k, 470k, 1M) 1/2 w, replacement of 2 vacuum tubes (6550), bias adjustment)
Accessories: copy of instruction manual
Main specifications: tubular mono power amplifier using vacuum tube KT88/5AR4/6AN8A output 60W/140W W229 × H190 × D229 mm 11.5 kg
The price has been reduced. 2024/5/30 sales price 128,000 yen Maintained! This is a Dynaco tubular control amplifier. It is an amplifier where you can enjoy the warm and comfortable sound unique to vintage. While the microwave feel is moderate, the nostalgic sound with an emphasis on atmosphere has a unique, hard-to-get flavor. There is a feeling of use such as rust stains on the top and sides, and rust etc. on the knobs (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (12AX7, 2000 μF electrolytic capacitor, 1 μF replacement, 1/4 W resistance added as a measure to improve switching noise, vacuum tube socket and RCA jack caulking repair, parts check including block capacitors, and operation check with AC 100 to 117 V)
Accessories: none
Main specifications: vacuum tube 12 AX7 x 4, 12 x 4 line input 5 systems phono 1 system (mm) 1 pre-out system W385 x H134 x D230 mm 7 kg
Maintained! An eye-catching diamond-tone power amplifier with a rugged design. The extrusion of the mid-range is clear and the sound is slightly firm, but the sound is good, so it seems to go well with jazz and rock. There are small scratches and dents on the exterior as a whole (Mizusaki Ryo)
Maintenance information: 2024.6.1 Maintained (replacement of deteriorated transistors and capacitors in each circuit. Input volume and output relay contact correction. Electric circuit adjustment)
Accessories: copy of instruction manual
Main specifications: 2 mono construction system 100W+100W (8Ω) W425×H170×D285mm 16.5 kg
*One SP terminal is a replacement, so it is inexpensive. It hasn't arrived in a long time. This speaker system inherits the DS-205 design philosophy of making small-aperture woofers sound smoothly with a large capacity enclosure. You can enjoy the soft texture and loud sound. Serial 12502/12517 (Murakoshi Yoichi)
Maintenance information: 2024.5.30 maintenance (exterior cleaning/touch repair, 1 terminal replacement)
Accessories: jumper cable (external product)
Main specifications: 2-way bass reflex type 6.3 ohm 87 dB W360 x H925 x D290 mm 25 kg
Woofer edge softening treatment! Comes with a genuine stand DK-1000ZX (list price 50,000 yen). Standard diamond tone model. The characteristics of the Boron scoker, which is strong and has a good sound, shine through. The tight low range with supple stretch is a sound unique to Diatone. You can enjoy excellent sound regardless of genre. The exterior has small scratches and dullness. ※Saran net is out of stock. Serial 14308/14315 (Fujisawa Yukishi)
Maintenance Information: 2024.6.2 woofer edge softened
Accessories: Genuine stand DK-1000ZX ※Saran net missing
Main specifications: [DS-1000ZX] 3 way 3 speaker sealed type 6.3 ohm output sound pressure level 90 dB W360 × H690 × D341 mm 29 kg [DK-1000ZX] W360 × H195 × D300 mm 6.2 kg
Woofer edge softened! A mid-range model with Diatone. The speaker has a smooth, sharp, and firm sound, and has a clear outline of the sound, making it an all-round speaker. You can see a feeling of use, such as appearance, dullness, scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.1 Maintained (edge softening treatment)
Accessories: saran net
Main specifications: 3-way, 3-speaker sealed system, anti-magnetic playback frequency band, 35Hz to 32kHz, 6Ω, sound pressure level, 91 dB, maximum input, 200W, W359 x H691 x D352 mm, 25.6 kg
DENON analog player. It is a model that is easy to use and has excellent cost performance. The phono cable is detachable and can be replaced with a cable of your choice. This model is also suitable for introductory use. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Asaine Tomoho)
Maintenance information: 2024.6.1 operation confirmed
Accessories: instruction manual cartridge, EP adapter, subweight
Main specifications: quartz servo type direct drive speed 33 1/3 rpm, 45 rpm static balance S-shaped pipe arm needle pressure adjustment range 0 to 4.0 g compatible cartridge weight 14.0 to 20.0 g W450 x H170 x D370 mm 10.1 kg
DENON DL-301/2 case You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W67 x H80 x D41 mm 54.8 g (actual measurement)
The price has been reduced! 2024/5/29 Denon luxury analog player with sales price 89,800 yen. The shades and coatings of the cabinets are also impressive. The drive motor is powerful, and the stopping action is instantaneous in a blink of an eye until it rotates at a fixed speed. The sense of stability in operation is excellent, and record playback with high freshness is attractive. The exterior is scratched on the dust cover, small scratches, and dullness on the cabinet. Serial 3086300399 (Yonejima Satoshi)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: power cable, connection cord
Main specifications: quartz lock type direct drive 33/45 rotation static balance S-shaped pipe arm height adjustment range approx. 6 mm needle pressure adjustment range 0 to 4.0 g (1 scale 0.25 g) compatible cartridge weight 14.0 to 20.0 g (headshell included) W490 x H178 x D400 mm 13.6 kg
DENON's classic MC cartridge. The balance of localization and sound is excellent, and all music genres can be played without difficulty. I can recommend this cartridge to a variety of people, from analog beginners to experts (Murakoshi Yoichi)
Maintenance information: 2024.5.8 sound output confirmed
Accessories: needle cover, case
Main specifications: MC type output voltage 0.3 mV playback frequency 20 Hz to 45 kHz electrical impedance 40 ohms needle tip 16.5 microns round needle pressure 2.2 to 2.8 g dead weight 8.5 g
The price has been reduced! 2024/5/28 sales price 79,800 yen Maintained by the manufacturer in 2024/4! DENON's pre-main amplifier. It is a mid-size model, and a staple machine with excellent stability, with firm bass and delicate high frequencies. In addition to the bass energy from conventional models, you can enjoy well-balanced sound that takes into account the high mid to high frequencies with a high sense of transparency. There is a feeling of wear on the exterior, such as scratches and dullness. Serial 8061507480 (Jun Tamai)
Maintenance information: 2024.4.17 manufacturer maintained (Rch amplifier circuit, transistor and resistor replacement. Amplifier board soldering correction (both channels). (Idle current adjustment and operation inspection carried out.)
Accessories: instruction manual, power cable, original box
Main specifications: rated output 80W+80W (8Ω) PHONO1 system (MM/MC switching) dimensions W434 x H181 x D480 mm weight 24.0 kg
4th generation of the DENON 2000 series. It is an amplifier that can be enjoyed regardless of the genre of music, with its plump, loud mid and low frequencies, and a pleasant, sharp tone. There is overall dullness (Oikawa Tetsuji)
Maintenance information: 2024.6.2 operation confirmed
Accessories: power cable, instruction manual
Main specifications: High-rigidity 6-block, separate chassis, power amplifier, direct input, bi-wiring compatible, 80W+80W, W434 x H180 x D478 mm, 23.5 kg
※There is no problem with the sound output operation, but the LCD is dark and there are places where the characters disappear, so it is inexpensive. The company's first standalone USB-DAC and headphone amplifier compatible with DSD. This product took out the USB-DAC part of the company's CD player DCD-1500RE and finished as a standalone unit. Not only does it play music, but it also effectively upgrades the sound of movies and games on a PC. The exterior has noticeable scratches on the top plate, paint chips, etc. (Mizusaki Ryo)
Maintenance information: 2024.6.1 operation confirmed
Accessories: power cord
Main specifications: DSD signal sampling frequency 2.8224, 5.6448MHz sampling frequency PCM signal 32, 44.1, 48, 64, 88.2, 96, 176.4, 192 kHz input terminal USB (TypeB) x 1, optical digital input x 2, coaxial digital input x 1 output terminal analog audio output (L/R) x 1, headphone output x 1 (6.3 mm stereo standard jack) dimensions W170 x H57 x D182 mm weight 1.5 kg