The price has been reduced! 2020/11/9 sales price 70,000 yen maintenance completed. This is a 2-way network. Since bass can be pushed out well, and high frequency adjustment ranges can be obtained with 2 types of HF/MF attenuators, it is a model that is easy to match the desired sound quality. There are small scratches on the exterior due to the feeling of use. Serial 05234 07210 (Makoto Kono)
Maintenance information: 2020.11.9 maintained (common wiring reinforcement terminal solder removal, rust removal treatment, cleaning, ATT (x4) contact disassembly cleaning, contact grease application, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound check)
Accessories: none
Main specifications: W114 x H190 x D228 mm 1.8 kg Crossover frequency 1.2 kHz Impedance 8 ohms Level control is continuously variable up to -8 dB in the middle range is 2 kHz and the high range is continuously variable up to -6 dB at 10 kHz
※1 bottle only. Maintained! This is a rare blue frame (above) model LX5. The impedance is 8 ohms, and the cross is 500 Hz, so be sure to use a 175 or 375 driver that uses 8 ohms! There are spots, rust spots, and small scratches. (Honda Maki)
Maintenance information: 2021.12.21 Conductivity confirmed 2019.4.4 Maintained (re-fix the internal coil with silicone agent. Remove rust from terminals and mounting screws, clean, and tighten. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: No accessories
Key Specifications: Crossover Frequency: 500 Hz Level Control: 3 Position Switch Input Impedance: 16 ohms 159 x 153 x 120 mm 2.3 kg
Maintained on 2015.6.11. The graininess of the sound has been clarified, and the smoothness of the connection has also been improved. It is a crossover 1200 Hz network ideal for the combination of a 38 cm woofer and 1 inch driver. The exterior has paint peeling and stains. Serial 9858/9958 (Miura Kimiya)
Maintenance Information: 2015.6.11 Maintained (terminal polishing, cleaning, insulation bush mounting screw replacement. ATT cleaning. Input/output waveform and balance check, sound output check. (Frequency characteristic measurement check)
Accessories: no accessories
Key Specifications: Crossover 1200Hz 8Ω 3-Position Switch with Level Control
Maintained! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, there is a feeling of use, such as paint peeling off and scratches scattered around. Serial 17041 17049 (Hiroki Aso)
Maintenance information: 2023.3.31 Maintained (terminal rust removal, acid wash, insulating bushing & mounting screw replacement, ATT brand new replacement, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound output check)
Accessories: none
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/5/5 sales price 9,800 yen. ※1 bottle only. A crossover network with exactly the same structure as the company's X8. This network is recommended when using BB4 with a T350 or 12TRXB. There is a feeling of use such as peeling and scratching on the label (Mizushima Itsuro)
Maintenance information: 2023.5.5 operation confirmed
Accessories: none
Main specifications: crossover frequency 3,500 Hz 8 ohms allowable input 100 W external dimensions W114 x H89 x D92 mm weight 680 g
Maintained in October 2022! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, paint is bald and oxidized (Yonejima Satoshi)
Maintenance Information: 2022.10.7 Maintained (Terminal rust removal, acid cleaning, insulation bushing & mounting screw replacement. ATT replacement A frequency characteristic measurement check (~ approx. 42 kHz) was performed, and the original capacitor was continuously used for good results. Input/output waveform and balance check, sound output check.)
Accessories: no accessories
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
The price has been reduced. 2023/9/22 Sales price 69,800 yen ※Since this is a remodeled product, it is currently sold. 3-way network. The details of the crossover are unknown. The attenuator comes with FOSTEX's AT-50H (16 ohms for the middle range only). There is a slight creak, but the sound output has been confirmed. I even took pictures of the interior. Please refer to it. There is no original terminal block (Sasaki Shota)
Maintenance information: 2023.9.22 sound output confirmed
Accessories: none
Main specifications: 3-way network W210 x H235 x D158 mm 4.5 kg (actual measurement)
2023.12.18Maintained professional cross 800Hz network. It is used in the 4320, etc., and the low frequencies are pushed out smoothly, giving the impression that the clarity of the mid-high range has improved. This network is useful for creating 2-way systems where woofers have a certain amount of area. How about making a 2-way horn system with a 16Ω unit? There are stains and rust on the main body. (TERAMOTO Hidehiko)
Maintenance information: 2023.12.18 Maintained (terminal rust removal treatment, cleaning, mounting screw replacement. SW type ATT contact cleaning. Frequency characteristics are measured and checked, and the original capacitors are continuously used for good results. (Check the input/output waveform and balance, check the sound output)
Main specifications: crossover frequency 800 Hz impedance 12 to 16 ohms W122 x H154 x D132 mm 1.9 kg/1 unit
Maintained. The grain of the sound is clear and the smoothness of the connection has also been improved. This is a 1200 Hz crossover network ideal for the combination of a 38 cm woofer and 1 inch driver. The exterior has dullness and scratches due to use over time, serial 18254 18275 (Asaine Satoshi Law)
Maintenance Information: 2024.4.16 Maintained (Screws, Insulated Washer Parts Replacement Switch Contact Cleaning)
Accessories: none
Key Specifications: Crossover 1200 Hz 8 Ohm 3 Position Switch with Level Control
Maintained! A 1500 Hz crossover network perfect for combining the LE14A with the 175DLH and LE175. The exterior is dull and has small scratches (Oikawa Tetsuji)
Maintenance information: 2024.4.17 Maintained (2 VR attenuators, 12 screws, 24 insulating washers replaced)
Accessories: none
Maintained! A network with a crossover frequency of 7000 Hz. Ideal for MID/HIGH use in 3-way systems using the JBL 2420/2440. In addition to dullness and small scratches on the exterior, there is a feeling of use such as paint peeling. Serial 24693 24691 (Hiroki Aso)
Maintenance information: 2024.5.4 maintained (12 terminal terminal mounting screws, 24 insulating bushings replaced for deterioration. The capacitor used for terminal cleaning is a Dayton attenuator VR contact cleaning crossover 7000 Hz check)
Accessories: none
Main specifications: Crossover frequency 7 kHz allowable input (continuous program) 50 W impedance low range 12 to 16 ohms treble range 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
Maintained! Professional crossover 800 Hz network. It's an exhilarating sound with a good view. How about making a 2-way horn system with a 16 ohm unit? In addition to dullness and small scratches on the exterior, there is a feeling of use such as paint peeling. Serial 8091 8074 (Hiroki Aso)
Maintenance information: 2024.5.4 maintained (12 terminal terminal mounting screws, 24 rust and insulation bushings, deterioration replacement. The capacitor used for terminal cleaning is a Dayton attenuator switch contact cleaning crossover 800Hz check red terminal cap partial deterioration replacement)
Accessories: none
Main specifications: crossover frequency 800 Hz impedance 12 to 16 ohms W122 x H154 x D132 mm 1.9 kg/1 unit
Maintained! A network using excellent parts such as high-voltage nonpolar capacitors and coils using low-loss Orient Cores. The cross is easy to use at 500 Hz, and it is a very easy to use network for those who are assembled with drivers such as 375 (Asaine Tomoho)
Maintenance information: 2024.5.16 Maintained (12 terminal terminal mounting screws, 24 insulation bushings, terminal part cleaning, main unit internal check, attenuator VR replacement, crossover check)
Accessories: none
Main specifications: 2 way network, 500 Hz, 8 ohms
Maintained! JBL's 2-way network. An essential item when adding a tweeter driver to a full range unit such as the D130. The exterior has paint peeling and dullness. Serial 39585 38470 (Tomonori Asaine)
Maintenance Information: 2024.5.16 Maintained (12 Terminal Mounting Screws, 24 Insulating Bushings, Terminal Cleaning, Attenuator, VR Replacement, Crossover Check)
Accessories: none
Main specifications: 2-way network 8 ohm crossover 2,500 Hz W121 × H153 × D93 mm 0.7 kg
Maintained! A network with a crossover frequency of 7000 Hz. Ideal for MID/HIGH use in 3-way systems using JBL 2420/2440 (Oikawa Tetsuji)
Maintenance information: 2024.5.19 maintained (12 terminal terminal mounting screws, 24 insulating bushings, deterioration replacement, terminal cleaning attenuator, replacement crossover check OK for VR Gari)
Main specifications: Crossover frequency 7 kHz allowable input (continuous program) 50 W impedance low range 12 to 16 ohms treble range 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
8000 Hz network for high range It can also be used in combination with JBL 077 or when combining a full range with a tweeter. Exterior, paint deterioration and peeling, dullness, and feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 maintained (terminal terminal deterioration replacement, terminal cleaning (coil replacement) attenuator VR replacement, crossover 8000 Hz check OK)
Accessories: none
Key Specifications: 2 Way Variable Level Control Crossover Frequency 8kHz 8Ω Weight 0.9 kg
Maintained. With a 7000 Hz crossover, this network is ideal for tweeters such as 075 and 077! Please enjoy using it in a way that suits your needs, such as 2 way or 3 way. Exterior, paint deterioration and peeling, dullness, and feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 maintained (terminal replacement, terminal cleaning (coil replacement) attenuator VR replacement, crossover 7000 Hz check OK)
Accessories: none
Key Specifications: Variable Level Control Crossover Frequency 7kHz 8Ω Weight 900g