The price has been reduced! 2024/5/10 sales price 398,000 yen Maintained! A pre-main amplifier with a built-in McIntosh traditional output transformer. You can enjoy the rich and rich sound world typical of Macintosh. This is one that combines the sound appeal of modern and old McKinn. The sense of power that makes you feel the strength is similar to that of a separate amplifier. As for the exterior, there is some rust on the top plate. Serial JMC1488 (Fujisawa Yukishi)
Maintenance information: 2024.5.10 Maintained (VR part gearbox with motor disassembly, cleaning grease replacement. Meter and panel lamp, grommets, and tact SW replacement. Screw replacement. Cleaning volume, loudness, etc. Solder correction. Bias and offset checks. Output audio check. Remote control operation check)
Accessories: remote control, copy of instruction manual
Main specifications: 150W+150W (8/4/2Ω) phono input MM dimensions W445 x H179 x D508 mm weight 30 kg
This is Altech's classic 1 inch 4 sectional horn. With a 1-inch driver of your choice, such as the 802-8D, you can enjoy the horn sound unique to Altec with good sharpness. The exterior has dullness and small scratches due to aging (Yonejima Satoshi)
Main specifications: crossover 500 Hz directional horizontal 90 x vertical 40 throat diameter 250 mm W600 x H270 x D 486 mm 6.7 kg
YBA's high-precision line preamps equipped with independent left and right volumes are in stock for the first time at Hi-Fi! In addition to the supple and glossy tone unique to YBA, you can also feel the high level of separation, it is authentic. A CP machine with a high level of satisfaction over the price. The exterior is dull and has small scratches on the top plate. Serial P21900L (Yonejima Satoshi)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: instruction manual, power cord
Main specifications: input: LINE/5 systems (RCA), output impedance: 20 ohms, output terminals: 2 systems (RCA) W430 x H83 x D330 mm, 5 kg
The price has been reduced! 2024/5/23 sales price 39800 yen Chinese SMSL D/A converter. ESS's ES9068AS is used as the DAC. Although inexpensive, it supports a wide range of inputs such as AES/EBU and I2S. The exterior is dull. Serial 4600010200207 (Fujisawa Yukishi)
Maintenance information: 2024.5.23 Operation confirmed
Accessories: remote control, instruction manual, power cord, original box
Main specifications: input USB, optical, coaxial, I2S, 1 AES/EBU system each W210 x H40 x D170 mm 1.2 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/28 sales price 99,800 yen D/A converter with a dual monaural configuration equipped with 2 “ES9038PRO” units. Using 3 Talema toroidal transformers, you can feel the creator's commitment. More natural sound can be reproduced. On the exterior, there are noticeable line marks on the top plate (Tamura Eiji)
Maintenance information: 2024.4.28 Operation confirmed
Accessories: power cable
Main Specifications: Coaxial/BNC/AES/Optical: PCM44.1k to 192 K/16 to 24 bit, DOP64 I2S Input: RJ45/HDMI PCM44.1K to 768K 24/32 bit DSD64 to DSD1024 DOP64 to 256 W430 x H80 x D335 mm Weight 5.4 kg
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. You can see the exterior, dullness, stains, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.2.13 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
The price has been reduced! 2024/5/16 sales price 17800 yen ※Since it is cheap, it will be handed over as is. Chinese vacuum tube amplifiers have arrived. The vacuum tube uses FU32, and is compact and designed to be just the right size for a desktop, etc. There is a thread on the exterior (Tamura Eiji)
Maintenance information: 2024.5.16 Operation confirmed
Accessories: none
Main specifications: 4W x 2 (4Ω) frequency response 26 to 38 kHz W296 x H150 x D210 mm weight 5.7 kg
The price has been reduced! 2024/5/17 sales price 49,800 yen Maintained! Sansui's rare CD player. The firm outline and comfortable sound are attractive. I would like to use it in combination with the company's α series premain for a unified look. In addition to listening to CDs, it also has a convenient function when recording to tape, etc., and has a variety of aspects. The exterior has scratches and line scratches. Serial 619097168 (Fujisawa Yukishi)
Maintenance information: 2024.5.17 Maintained (loading and clamp mechanism drive belt replacement. Front panel operation tact switch replacement. Optical system cleaning cleaning)
Accessories: No accessories
Main specifications: 1-bit linear & direct conversion system (4DAC) W430 × H127.5 × D397.5 mm 8.8 kg
YBA's rare power amplifier is in stock for the first time at Hi-Fi! Uses a large double power transformer and an original Motorola power transistor. Engineers who were in charge of design at Goldmund are in charge of production, and the sound field is large. It is an amplifier with a very high degree of perfection, with precise tone, medium and low frequencies with intonation, etc. The exterior has dullness, threads, etc. (YONEJIMA Satoshi)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: power cord
Main specifications: 85W+85W (8Ω) 170W+170W (4Ω) W430 × D330 × H132 mm,22 kg
An attractive CD player with a smart design and stable playback ability while being inexpensive. You can enjoy music without getting tired with a smooth, bright tone. The exterior is generally dull and has small scratches. Serial C72PJ1136 (Yonejima Satoshi)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: power cable
Main specifications: digital output/coaxial 1, optical 1 analog output/1 system W430 × H85 × D290 mm 4.4 kg
The price has been drastically reduced! 2024/5/23 sales price 198,000 yen ※This is a record player with Garrard 401 and Technica AT-1503/3 mounted on a 50Hz double arm cabinet. The powerful, thick, and energetic sound unique to rim drives is attractive, and you can enjoy the rich sound typical of analog. The exterior has peeling, scratches, erased characters, scratches, etc. Serial 42640 (Tamura Eiji)
Maintenance information: 2024.5.23 Maintained (dirt cleaning. Motor disassembly, inspection, lubrication and assembly. Motor spring rubber sleeve replacement. AC cord replacement Main bearing disassembly, bearing thrust replacement, lubrication, oil sealant application, assembly. idler cleaning. Speed adjustment linkage adjustment. brake adjustment. Oil felt replacement. Mounting stud bolts missing/added; nuts, metal washers, and rubber washers added. Running tests OK. (*There is a slight loud noise when turning in the opposite direction, but this is the current situation)
Accessories: No accessories
Main specifications: 50 Hz specification idler drive 33/45/78 rotation arm part: static balance type execution length 257 mm compatible cartridge 13.5 to 33 g (including shell) needle pressure range 0 to 3 g W540 x H180 x D640 mm
The disposal price has been reduced! (Member prices are not applicable) 2024/4/12 sales price 79,800 yen ※It is cheap because it is in poor condition. Equipped with a coaxial unit, sound localization is good, the high frequencies are clear, and the sense of volume in the low frequencies is sufficient for the size, so you can relax and listen to classical music in small groups. It also has good efficiency, so it's easy to play, and it features a chic design with a shiny mirror piano paint. In addition to being scratched, some Saran magnets are missing. Also, there is a slight wobble in the SP terminal on the + side on one side, and one screw that stops the terminal board is missing. (FUJISAWA KOSHI)
Maintenance information: 2024.4.9 operation confirmed
Accessories: saran net
Main specifications: 36Hz to 22kHz 45W 4Ω 93.5dB W207 × H990 × D274 mm 17 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/21 sales price 99,800 yen DALI's HELICON series center speaker. If you use the company's HELICON series and are considering surround, please give it a try. The exterior is dull. Serial 7660180 (Fujisawa Yukishi)
Maintenance information: 2024.4.21 operation confirmed
Accessories: original box, saran net
Main specifications: 4Ω playback frequency band 49Hz to 27kHz W650 ✕ H210 ✕ D435mm weight 18.4 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/15 sales price 128,000 yen LINN network audio player with an integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1234701 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
The price has been reduced! 2024/5/25 sales price 69,800 yen ※The exterior is in poor condition, so it's cheap. An upgraded model of PMC's small monitor DB1. It has excellent characteristics as a near-field monitor, and is characterized by good phase characteristics and rich spatial expression. It is a high-quality model that can be further upgraded by adding an amplifier. There are line scratches and bumps on the exterior. Also, there are cracks or tears in the urethane on the back. Serial 012503/012504 (Yonejima Satoshi)
Maintenance information: 2024.5.25 sweep test good
Accessories: saran net
Main specifications: 2 way 2 speakers, frequency characteristics, 50 Hz to 25 kHz, output sound pressure level, 87 dB, impedance, 8 ohms, dimensions: H290 x W155 x D240 mm (including grille), mass: 4.5 kg
Denon high-end MC cartridges in the heyday of analog, using amorphous boron pipes. A sound with a wide range and good separation, which has a different trend from the standard 103 series. This is the reference cartridge at the time. There is slight dirt and a feeling of use. (FUJISAWA KOSHI)
Maintenance information: 2024.5.27 Operation confirmed
Accessories: instruction manual, needle cover
Main specifications: MC type output 0.2 mV 40 ohm boron cantilever solid diamond special oval needle playback band 20 to 75 kHz proper needle pressure 1.0 to 1.4 g dead weight 5.8 g
The higher model of the DL-103. Wide range was measured, and 20 Hz to 70 kHz was achieved. Delicate, wide, and powerful sound quality. There is slight dirt and a feeling of use. ※There is a note on the original box. (FUJISAWA KOSHI)
Maintenance information: 2024.5.27 Operation confirmed
Accessories: instruction manual, original box, needle cover
Main specifications: MC type output 0.2 mV playback frequency 20 to 70,000 Hz impedance 40 ohms needle pressure 1.2 g dead weight 6.5 g
Popular ceramic shell. A beryllium copper washer and a three-point crimping system are used at the arm joint. The overhang can be adjusted by means of a slide plate on the top. (FUJISAWA KOSHI)
Maintenance information: 2024.5.27 continuity confirmed
Accessories: No accessories
Main specifications: sintered aluminum oxide body, 3-point crimping type, weight 18 g
Popular ceramic shell. A beryllium copper washer and a three-point crimping system are used at the arm joint. The overhang can be adjusted by means of a slide plate on the top. (FUJISAWA KOSHI)
Maintenance information: 2024.5.27 continuity confirmed
Accessories: No accessories
Main specifications: sintered aluminum oxide body, 3-point crimping type, weight 18 g
※It is inexpensive because it is in poor condition, such as rust. Maintained! A vintage Lux Premain model. The 75W yet firm, extruded bass and thick, mild mid-high sound are lackstones themselves. Enjoy playing records with a tasteful sound. The exterior is serial 2503734 (Yonejima Satoshi)
Maintenance information: 2024.5.25 Maintained (main amplifier circuit board solder correction. Switch and volume contacts corrected. Panel lamp replacement Output relay replacement. (I/O pin jack polish)
Accessories: No accessories
Main specifications: 75W+75W phono 1 system (MM/MC switching) line 2 tape systems, 2 tape systems, pre/power separable, W453 x H135 x D425 mm 13 kg
※1 bottle only. The diaphragm has been replaced with a D8R2421. It is an 8 ohm specification. Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. Serial 23890 (Yonejima Satoshi)
Maintenance information: 2024.5.25 Maintained (diaphragm installation adjustment, pad dampener, mounting screw rust replacement. Material terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning. (This is a genuine diaphragm, but it comes with D8R2421)
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 8 ohms (3.8 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
The price has been drastically reduced! 2024/5/11 sales price 128,000 yen Maintained! Late QUAD44 with CD input terminal. It's not flashy, but the thick, glossy tone is attractive. In particular, it softens female vocals. Serial Q36114 (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (internal power supply switch contact dirt contact polishing treatment, balance VOL cleaning ~ check OK. Check the other boards and re-solder the holes. (C, R check OK)
2024.5.9 Internal power supply switch contact polishing treatment
Accessories: power cord
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321 x H103 x D203 mm, 4.0 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/5/14 Torrens entry model with sales price 118,000 yen. Although it is an entry model, the silence and smoothness of the belt drive, and the delicate sound are attractive, and the tone arm is easy to adjust. Recommended for entry-level belt drive machines. There are a few small scratches on the exterior. Serial 00262803 (Fujisawa Yukishi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: copy of instruction manual, power cord, connection cord, spike base, original box
Main specifications: W420 x H125 x D330 mm 8 kg Drive system: belt drive motor: synchronous motor speed: 33 1/3, 45 rpm electronic speed selection platter: diameter 300 mm, 3 kg, aluminum power supply unit housing tone arm: static balance type
Maintained! Comes with a remote control. This model was created by gathering the know-how of the Integra series. There are only models produced with a thorough emphasis on sound quality, which is a bit different from other Integra series, and has a relaxed, relaxed sound. The exterior has dullness, threads, and small scratches. Also, the SP terminal has been replaced. Serial 6301012428 (Yonejima Satoshi)
Maintenance information: 2024.5.22 Maintained (disassemble the push switch and remote wire switch, polish the contacts, and apply contact cleaner. Volume contact correction. Remote control operation check OK)
Accessories: remote control, instruction manual
Main specifications: 155W+155W (6Ω) 120W+120W (8Ω) damping factor 400 (8Ω) frequency characteristics 2Hz to 100kHz W471 ✕ H170 ✕ D430 mm 26.6 kg
The price has been reduced! 2024/5/15 sales price 29,800 yen A low-cost clock generator that emits a high-performance master clock. It is recommended for those looking for expressive power with a precise amount of spatial information. By inputting a high-accuracy 10 MHz reference output obtained from a high-precision transmitter for measurement or military transmitters (using rubidium, cesium, GPS) not manufactured as an audio device to the external clock input terminal, it is possible to transmit an even more accurate master clock. The exterior is dull. (YONEJIMA Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: power cord
Main specifications: 2 clock outputs (BNC) 44.1 kHz/48 kHz magnification x 1/2/4 (maximum 44.1 to 192 kHz), 1 10MHz clock input system (BNC), size W190 x H56 x D220 mm 810 g
The price has been reduced! 2024/5/8 sales price 12,000 yen ※The exterior is in poor condition, so it's cheap. 1 bottle only Altec green horns were also used in the early A7. While it has wide diffusion characteristics, it is an attractive horn because it is easy to listen to where you can feel the core. The exterior is dull, scratched, and peeling paint (Yonejima Satoshi)
Accessories: No accessories
Main specifications: 800Hz crossover frequency compatible driver 802-8D, 806-8A, 807-8A W470 × H220 × D340 mm 4.1 kg
Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has rust and paint peeling due to aging. ※The diaphragm is DR16R2421. (YONEJIMA Satoshi)
Maintenance information: 2024.5.25 Maintained (diaphragm installation adjustment, pad dampener, mounting screw rust replacement. Material terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning. This is a genuine diaphragm, but it comes with DR16R2421. DCR (A/7.1 ohm diaphragm scratch) DCR (b/6.3 ohm diaphragm scratch))
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg/piece
Maintained! The successor to the C-220, which was particular about the phono equalizer. Models from the heyday of analog are notable models that focus on records. The deep, authentic sound quality of PHONO with good sharpness is attractive. The exterior is dull and has small scratches. Serial C4X515 (Yonejima Satoshi)
Maintenance information: 2024.5.25 Maintained (contact cleaning due to poor main volume and balance volume. Due to poor contact with the compensation center switch in the sealing door, disassembly contact polishing contact grease was applied. Electrolytic capacitor replacement near the heating unit. (Check the operation of each input/output)
Accessories: power cord, copy of instruction manual
Main specifications: PHONO (MM/MC) line input 5 systems W466 x H153 x D385 mm 9.7 kg
It's a small digital interface that fits in the palm of your hand. The input uses a Type-C USB interface. The output is I2S/optical/coaxial. The sampling rate is PCM32 bit/768 kHz compatible, DSD native, DOP64 compatible (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: original box, connection cable
Main specifications: W80 x H13 x D60 mm dead weight 120 g
The 0.5 m HDMI cable connector is made of high-grade aluminum material, and the outer skin of the cable uses a slim nylon mesh cable that can be wired neatly and is less burdensome when bending. Compatible with 4K2K (60P), it is possible to faithfully transmit high quality video and sound (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: case
The HDMI cable is a 3.0 m high-grade connector, and a nylon mesh cable is used for the outer shell. It is possible to faithfully transmit high quality video and sound (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: none
The 1.2m pair of unprocessed speaker cable has excellent balance from low to high frequencies, and has an energetic and warm tone. There are threads and disappearing characters on the exterior (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: none
The disposal price has been reduced! (Member prices are not applicable) 2024/4/9 sales price 99,800 yen with wood horn! Maintained! An integrated mid-range driver unit developed for 3-way use. It's an energetic, easy-to-read sound typical of YL. Paint peeling can be seen in places. Serial 751903, 751903 (Fujisawa Yukishi)
Maintenance information: 2024.4.9 maintained (coil roundness adjustment, noise suppression, porcelain circuit slit maintenance)
Accessories: No accessories
Main specifications: Playback frequency band 800 to 8,000 Hz maximum input 40W 8Ω output sound pressure level 101 dB outer diameter W400 × H200 × D350 mm 3.30 kg
The price has been drastically reduced! 2024/5/9 sales price 39,800 yen D/A converter with a built-in “ES9038PRO.” This model has a compact design, is compatible with MQA, high-resolution, and DSD sound sources, and has excellent cost performance. Desktops etc. are the worst. There are no noticeable scratches on the exterior (Tamura Eiji)
Maintenance information: 2024.5.9 operation confirmed
Accessories: instruction manual (no Japanese), remote control, AC adapter
Main Specifications: Input: USB/OPTICAL/COAXIAL/BLUETOOTH USB: 44.1 to 768 kHz/DSD64 to 512 OPTICAL/COAXIAL: 32 to 192 khz W100 x H62 x D192 mm Weight 0.58 kg
HDMI cable 1.0 m transmission speed 10.2 Gbps to 21 Gbps (varies depending on cable length) The shorter the cable, the faster the transmission speed. (FUJISAWA KOSHI)
Maintenance information: 2024.5.23 continuity confirmed
Accessories: No accessories
Pickering's classic headshell. The aluminum press finish has just the right amount of sound. The overhang is adjustable, and the wide mounting width makes this model easy to use. There is a slight screw scratch. (FUJISAWA KOSHI)
Maintenance information: 2024.5.23 continuity confirmed
Accessories: No accessories
Main specifications: aluminum stamping weight 8.2 g
※ Because it is cheap, it is currently sold. JBL 2-way speaker. It is a large, well-balanced model that is easy to use. It is also recommended as a speaker for BGM in stores, etc. On the exterior, there are stains and adhesive marks on the edges. Also, there are some holes on the sides. Serial 121213353121213 (Yonejima Satoshi)
Maintenance information: 2024.5.19 sweep test good
Accessories: grill net
Main specifications: W152 × H232 × D140 mm 2.5 kg
Exclusive stand for the DS-77HR sold separately. Of course, it is also recommended for other medium speakers. The exterior has creases, floats, scratches, etc. (Tamura Eiji)
Accessories: No accessories
Main specifications: W410 x H264 x D330 mm weight 10 kg
YAMAHA speaker stand The compact stand is made to feel stiff, and you can expect tight sound quality. It can be used for small speakers such as the NS-10M and medium speakers. There are line marks, threads, and tape marks on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: W270 x H494 x D350 mm top plate part W190 W x D175 mm 7 kg/unit
※Since it is cheap, it will be handed over as is. A mixer with an effect loop that can mix 3 channel inputs (microphone or line) and 3 stereo line systems. The exterior has dullness and scratches. Serial M1007000864 (Tamura Eiji)
Maintenance information: 2024.5.19 simple check OK (details will not be checked)
Accessories: No accessories
Main specifications: W483 x H44.5 x D152 mm weight 2.8 kg
A record player equipped with a Bluetooth (R) function and a USB output terminal. It can be connected to a Bluetooth (R) compatible wireless speaker, etc., and is recommended for those who want to enjoy a record player casually. As for the exterior, there is a thread on the dust cover. Serial 1007740 (Tamura Eiji)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: AC adapter, EP adapter
Main specifications: W516 × H198 × D433m mass 5 kg
※ It is inexpensive because it is in poor condition such as dirt and felt peeling. Set of 3 classic TAOC basses. Made of high-carbon cast iron with excellent vibration handling capabilities. It can be used for a wide range of speakers from large to medium, and accurately reproduces sound images. The exterior has rust and dirt due to aging, and deterioration in the bottom felt (Satoshi Yonejima)
Accessories: none
Main specifications: W100×H200×D300mm 9.2 kg
Speaker cable is a current CARDAS entry series speaker cable with an unprocessed 4-core structure with 1.5 m pair terminals. Use Perfect Surface Copper. The high frequency extension of the single line and the Ritz line is an appeal that cannot be obtained anywhere else. (FUJISAWA KOSHI)
Maintenance information: 2024.5.18 continuity confirmed
Accessories: No accessories
※1 bottle only. Woofer for the famous Japanese instrument 2S-305. The Alnico magnet makes a pleasant low frequency. How about for repairs or for a new system? The urethane part is defective due to deterioration. (FUJISAWA KOSHI)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: No accessories
Main specifications: Alnico magnet, 30 cm, 8 ohms, 20 W, 40 Hz to 1500 Hz, diameter: 313 x depth: 168 mm, weight: 8.5 kg
Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. Serial 60878/74750 (Tamura Eiji)
Maintenance information: 2024.5.18 Maintained (diaphragm installation adjustment. Pad dampener, mounting screw rust replacement Wiring terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning, internal wiring cable replacement. DCR (74750/6Ω diaphragm no scratch) DCR (60878/5.7Ω diaphragm no scratch))
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
A compact, high CP, and easy headphone amplifier. The sound is bright and has good visibility. A well-balanced model that works well with everything from pop to rock. Serial 32741 (Fujisawa Yukishi)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: instruction manual, AC adapter
Main specifications: output 330 mw/30 ohm, 60 mw/300 ohm headphone amplifier connection, 30 ohm gain, 11 dB S/N ratio, 87 dB frequency characteristics, 30 to 20 kHz, input/output RCA, 1 system each, W103 x D127 x H38 mm, 1.40 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/23 sales price 99,800 yen, genuine Rin Japan product. A network audio player. It has a simple and modern European design, so you can enjoy a bright sound without getting tired of listening. Not only is it compatible with the LINN system, but it is also equipped with digital output and variable line level output functions not found in the KLIMAX DS and AKURATE DS. There is a thin scratch on the top plate. ※The display is slightly dark, but this is the current situation. Serial 1255165 (Fujisawa Yukishi)
Maintenance information: 2024.4.23 Operation confirmed (Ver. 4.104.518)
Accessories: remote control, power cord
Main specifications: Compatible sampling frequencies 44.1K, 48K, 88.2K, 96K, 176.4K, 192K compatible bits 16-24 bits, output terminals RCA phono (fixed/variable line level output), RCA phono coaxial (digital output) W381 x D360 x H80 mm 4 kg