The disposal price has been reduced! (Member prices are not applicable) 2024/6/4 sales price 268,000 yen Maintained! LUXMAN 70th anniversary signature model. The standard EL34 push-pull configuration has an OY transformer, and is designed so that you can fully enjoy the flavor of luxe stone. Using an unprecedented high-rigidity chassis, it also has an outstanding sense of luxury. This is a 90s vacuum tube premain with a good balance of range, thickness, and tone. There is a scuff on the front knob. Serial W51010230 (Hiroki Aso)
Maintenance information: 2024.1.13 maintained (2 output tubes replaced due to right channel bias, double channel drive stage socket replacement switch contact disassembly cleaning volume cleaning knob milling deviation correction vacuum tube pin cleaning bias adjustment output audio check, approx. 30W at 8 Ω load)
Accessories: instruction manual copy power cable
Main specifications: output 30W+30W (6Ω) phono (mm) 2.5mV/47kΩ vacuum tube EL34 (6CA7) x 4, 12AU7 x 4, 12BH7A x 2 W430 x H209 x D387 mm weight 22 kg
Full maintenance was carried out to replace all deteriorated parts such as capacitors and vacuum tubes! 38 FD, the most popular of the 38 series, is now in stock! The warm tone has plenty of warmth in the bass and mids, and you can enjoy the true essence of lackstone, where you can enjoy the afterglow of the tone. The exterior has a beautiful finish due to exterior maintenance, but rust etc. on the back remain. Serial 101 20007 (Tomoho Asaine)
Maintenance information: 2024.6.6 maintained (parts replacement, input/output waveform check, load test (1kHz sine wave, 8Ω load: 30W+30W, OK), sound output test) 2020.4.2 maintained (vacuum tube (50CA10), electrolytic capacitor, block electrolytic capacitor, coupling capacitor, vacuum tube socket, headphone jack, micro switch, rectifier diode, semi-fixed resistor, fuse replacement. Complete disassembly of SW/VOL contacts, polish, and apply grease to prevent oxidation and sulfidation. Circuit readjustment, input/output waveform confirmation, load test (1kHz sine wave, 8Ω load: 30W+30W), distortion adjustment (maximum output: 0.2%), sound output test)
Accessories: manual copy power cord
Main specifications: 30W+30W (4, 8, 16 ohms) line input 4 systems phono 2 systems (mm) W476 x H190 x D335 mm 18 kg
The disposal price has been reduced! (Member price not applicable) 2024/5/26 sales price 298,000 yen Current belt drive type player equipped with Luxman's original tonearm. Dust coverless specification The high initial motion sensitivity unique to knife-edge bearings, stable trace performance, and excellent sound quality delivered from a machined aluminum heavyweight platter are attractive. Despite its compact size, you can enjoy authentic analog sound. The appearance is good with little feeling of use. Serial M21000149 (Tomoho Asaine)
Maintenance information: 2024.5.26 Operation confirmed
Accessories: instruction manual, power cord, original box, shell screwdriver, 2 hex wrenches, handles
Main specifications: belt drive system PID controlled brushless DC motor 33 1/3 rpm, 45 rpm, 78 rpm switchable static balance, S-shaped universal type knife edge structure compatible cartridge dead weight 4 to 10 g (17 to 23 g including attached headshell) anti-skating 0 to 4 g W465 x H133 x D393 mm weight 15.8 kg
A line cable that uses high-purity oxygen-free copper (OFC) wire as the balance cable 1.0 m pair core wire and shield wire. It is a neutral sound that brings out the individuality of amplifiers and players (Tomonori Asaine)
Maintenance information: 2024.6.9 continuity confirmed
Accessories: none
The disposal price has been reduced (member prices are not applicable) 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg
The disposal price has been reduced (member prices are not applicable). 2024/2/16 sales price 378,000 yen ※The power supply part has been newly created. Other internally deteriorated parts have been restored! 2-way 100Hz specification An electric crossover coveted by Mark Levinson fans. You can see how well the early Levinson was built can be seen from the feel of the knobs that seem to make you addicted. You can listen closely to Levinson's unique sounds even on Divider. The exterior has scratches on the front top plate and other threads (Mizusaki Ryo)
Maintenance information: 2024.2.16 Maintained (*Since there is no power source, new power supply and connection cable were manufactured, noise appears in the LChLow output, transistor defects in the low pass module were replaced, re-encapsulated, readjusted due to left and right level differences, 4 volume contacts were cleaned, specs were inspected, and blocking characteristics were inspected. The crossover is 100Hz)
Accessories: Power supply unit (newly created, non-genuine), power cable, copy of instruction manual
Main specifications: 2 way (100 Hz specification) closed module type RCA Remo input/output size (main unit) W483 x H51 x D156 mm 2.8 kg size (power supply part) W101 x H101 x D256 mm 2.2 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/2/10 sales price 198,000 yen Maintained! According to the 117V specification of the tubular mono FM tuner, reception is unstable at 100V. The Japanese band has been changed, and reception sensitivity is good. It is a tuner that strongly shows the characteristics of Mackin's sound, which is thick, soft, and glossy. There is corrosion and rust throughout the exterior. Serial 292099 (Tomoho Asaine)
Maintenance information: 2024.2.10 Maintained (meter readjustment with coil and right side volume, left side lamp off replacement, IF/RF/MPX readjusted)
2018.2.22 Maintained (VT12AT7 replacement/MPX section transistor replacement/RF/IF/MPX re-adjustment)
2016.1.25 Maintained (6 additional VT shortages. 2 VT replacements 4 additional ceramic C for BAND EX Ceramic C replacement. Chemical C exchange. Front lamp repair, block.C50uf x 4 replacement Step up transformer 100V ⇒ 117V added)
Accessories: 117V step up transformer
Main specifications: FM dedicated tuner W400 x H130 x D300 mm 8.6 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/5/31 sales price 128,000 yen Maintained! Hi-Fi is in stock for the first time! Macintosh transistor AM/FM tuner. The reception sensitivity is also good, and you can enjoy deep and warm sound even though it is a transistor. The exterior is scratched and dull. Serial JCR1658 (Jun Tamai)
Maintenance information: 2024.5.31 maintained (varicon cleaning, F cover adjustment, OSC capacity adjustment, windshield peeling correction, each SW and VOL cleaning)
Accessories: none
Main specifications: W405 x H135 x D360 mm weight 8.1 kg
Comes with an indicator If you're an audiophile, this is a British “static electricity removal pistol” that you definitely want to have. With a mechanism that neutralizes static electricity with positive and negative ions, incidental sounds disappear, and the sound quality of analog records and CDs is improved to a clean sound with good visibility. Can be used approximately 50,000 times without using batteries (Asaine Tomo)
Maintenance information: 2024.6.9 operation confirmed
Accessories: original box, indicator
Key Specifications: Static Electricity Removal Accessory for LP/EP
The price has been drastically reduced! 2024/6/4 sales price 79,800 yen The Silver series is used in woofers that use the new DCF technology. The unit, which has the familiar high-speed texture, is stored in a relatively large enclosure. The low range, which has more volume than the size, and the clear mid to high range are attractive. The exterior has a feeling of use such as dullness. Cereals (Tomoho Asaine)
Maintenance information: 2024.6.3 sound output confirmed
Accessories: jumper cable (general purpose)
Main specifications: 2-way bus reflex type frequency characteristics 40 Hz to 35,000 Hz, crossover frequency 2,800 Hz, efficiency 88 dB, impedance 8 ohms, W230 x H375 x D329 mm, weight 9.3 kg/unit
It is one of Monster Cable's representative works that uses an unprocessed time correction structure at the 3.0 m and 1.9 m pair end of the speaker cable, and is quite thick with a conductor system of 3 mm. It is a cable with large changes in sound quality that can easily produce a sense of volume of bass (Tomoho Asaine)
Maintenance information: 2024.5.9 continuity confirmed
Accessories: none
RCA cable 1.0 m pair with 24K gold-plated turbine plug and split center pin specification, 2-core structure, sheath resistant to aging, and Duraflex jacket. The exterior has a feeling of use and dullness (Tomoho Asae)
Maintenance information: 2024.5.9 continuity confirmed
Accessories: none
The price has been reduced! 2023/8/21 Sales price 500 yen*There is deterioration due to long-term storage, so quality cannot be guaranteed. This is a replacement needle for Nagaoka and is compatible with SANYO's ST-G5. The cushioning material has collapsed and adhered to due to deterioration (Asahina Satoshi Law)
Maintenance information: 2023.8.21 Operation has not been checked
Accessories: case
The price has been reduced! 2024/3/31 sales price 1,000 yen exchange needle for Nagoya. This is a Victor DT-ZL1S compatible product. Since there are no compatible cartridges, they have not been checked. *Quality cannot be guaranteed due to deterioration due to long-term storage (Takahashi Nobuyuki)
Maintenance information: 2024.3.31 unchecked
Accessories: case
The disposal price has been reduced! (Member discounts are not applicable) 2023/8/22 sales price 800 yen ※Quality cannot be guaranteed because deterioration due to long-term storage can be seen. Nagaoka replacement needles are compatible with COLUMBIA DSN-16 (Hiroki Aso)
Maintenance Information: 2023.8.24 Operation has not been checked
Accessories: case
NAGAOKA stylus cleaner. This is a standard cartridge cleaner product and an easy to use and convenient item. It's a volatile and safe cleaner. About 80% of the remaining amount is left (Yamato Yuki)
The price has been reduced. 2024/4/18 sales price 600 yen Nagaoka record cleaner using Italian velvet. The exterior shows a feeling of use such as dullness, etc., and wear on the velvet (Asaine Tomoho)
Accessories: none
The price has been reduced! 2024/6/7 sales price 5,000 yen A speaker system that solved problems unique to compact speakers and improved sound quality. A woofer using a 12 cm pure crystal fiber diaphragm is used for the low range, and a 2.5 cm soft dome tweeter is used for the high range. The enclosure has a new round shape with a suede-like coating. The attached stand is detachable. There is a feeling of use on the exterior, such as dullness and small scratches (Jun Tamai)
Maintenance information: 2024.6.4 sound output confirmed
Accessories: saran net
Main specifications: main body W149xH366xD221mm stand W148xH60xD232mm
Weight 5.4 kg (main unit 4.7 kg, stand 0.7 kg)
The disposal price has been reduced! (Member discounts are not applicable) 2023/6/27 sales price 500 yen ORSONIC dry record cleaner. In addition to the velvet on the cleaner surface peeling off, there is an overall feeling of use (Asaine Tomoho)
Accessories: none
Digital cable 1.0 m RCA plug This 75 ohm digital cable is ideal for generating clocks such as clock generators, word clock connections for receiving devices, S/PDIF connections to DACs, audio interfaces, DJ devices, etc., and video equipment. The exterior is dull (Tomonori Asaine)
Maintenance information: 2024.6.9 continuity confirmed
Accessories: none
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand a single point load at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand single point loads at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
This is a set of 4 small spikes. It has good cost performance, high rigidity that can withstand a single point load at point contact, and achieves stable point contact. There is a feeling of use on the exterior such as dullness and small scratches (Tamai Jun)
Accessories: none
Main specifications: diameter 20 mm x H9.9 mm 15.8 g (1 piece)
An improved model of the S-77TWIN that adopted the vertical twin system. With a large sound field and clear sound image localization, there are few differences in sound, and it sounds smoothly and in a well-balanced manner, so you can enjoy it regardless of genre. The exterior has a feeling of use such as dullness, scratches, and cracks in the saran net. Serial JK0424 JK0425 (Hiroki Aso)
Maintenance information: 2024.6.13 sound output confirmed
Accessories: Saran net jumper cable (general purpose)
Main specifications: 2 way 3 speakers, 18 cm cone type for low frequencies x 2, 2.5 cm dome type, vertical twin, bi-wiring compatible for high frequencies, 6 ohms, 35 Hz to 40000 Hz, 91 dB/w/m, W268 x H960 x D376 mm, 29 kg
The price has been reduced! 2024/6/7 sales price 79,800 yen DSD compatible network audio player. It is possible to play music files on DLNA1.5 compliant media servers, such as PCs and NAS connected to a home network. It is also equipped with a USB TypeA/TypeB terminal. A high-capacity external hard disk, iPod/iPhone, USB memory input, a maximum 384 kHz/32 bit high-resolution sound source, and an asynchronous USB DAC function that enables native playback using a DSD sound source have also been realized. The exterior has a feeling of use such as dullness. Serial NJIV000297JP (Asaine Tomo)
Maintenance information: 2024.6.7 operation confirmed
Accessories: remote control manual power cord
Main specifications: sampling frequency 32 to 192 kHz DSD 5.6 MHz/2.8 MHz, compatible format DSF FLAC WAV MP3 WMA AIFF ALAC digital input/optical/coaxial iPod/iPhone USB memory external USB hard disk network terminal LAN (100base-TX/10base-T) W435 x H121 x D339 mm 12.5 kg
The price has been reduced! 2024/4/5 sales price 500 yen The sound quality of only one 2.0m QED speaker cable feels thick and flexible throughout the entire range. You can use it regardless of genre. The exterior is good with no conspicuous scratches (Tomoho Asae)
Maintenance information: 2024.4.5 continuity confirmed
Accessories: none
This is a QRD sound diffusion panel. By placing it behind the speaker, exquisite absorption and diffusion are possible, which is useful for improving sound image localization. There are spots and small scratches on the exterior (Tomonori Asae)
Main specifications: W600 x H1200 x D230 mm 16.5 kg
An acoustic panel for floors that mainly diffuses rather than absorbs sound. It is designed so that an overwhelming effect can be obtained in a limited space. The exterior is dull and has a feeling of use (Hiroki Aso)
Accessories: none
Key Specifications: Hybrid Diffusion Floor Panel W680 ✕ H36 ✕ D680mm 4kg
An acoustic panel for floors that mainly diffuses rather than absorbs sound. It is designed so that an overwhelming effect can be obtained in a limited space. The exterior is dull and has a feeling of use (Hiroki Aso)
Accessories: none
Key Specifications: Hybrid Diffusion Floor Panel W680 ✕ H36 ✕ D680mm 4kg
This is a QRD sound diffusion panel. By placing it behind the speaker, exquisite absorption and diffusion are possible, which is useful for improving sound image localization. There are spots and small scratches on the exterior (Tomonori Asae)
Accessories: none
Main specifications: W600 x H1200 x D230 mm 16.5 kg
※One shelf board has been added. Quadra Spire Clear Glass 3-tier black 2-tier type in all 5 tiers. In addition to excellent design, the shelf board has sufficient rigidity even though it has a simple structure, and it is subtly curved and cut so that vibration components gather at the four corners. Although the exterior has a light feeling of use, it is good without noticeable scratches (Yamato Yuki)
Accessories: none
Main specifications: inch step W600 x H890 x D475 mm from above shelves 260 mm, 140 mcm, 180 mm, 180 mm (actual measurement)
The price has been reduced! 2024/6/8 sales price 89,800 yen ※All 5 tier types with 2 tiers of CLEAR GLASS and 3 tiers of black. Spike specification In addition to excellent design, the shelf board has sufficient rigidity even though it has a simple structure, and it is subtly curved and cut so that vibration components gather at the four corners. Although the exterior has a light feeling of use, it is good without noticeable scratches (Tomoho Asaine)
Accessories: none
Main specifications: inch step W600 x H850 x D475 mm from above shelves, 100 mm, 180 mm, 220 mm, 220 mm (actual measurement)
The disposal price has been reduced! (Member discounts are not applicable) 2024/1/18 sales price 49,800 yen Maintained! An American-made amplifier from the 1970s that can hardly be seen today. Circuits for self-preservation, such as security, correction, and protection, have been cut off, and I think that handsome atmosphere is well reflected in the sound. It has the same feeling of use as the model year (Daiki Goto)
Maintenance information: 2024.1.18 Maintained (LED installation (original not available) poor power stage transistor deterioration, defective transistor in the board → replacement. Bias adjustment, operation check.)
Accessories: none
Main specifications: size (actual measurement) W406 x H155 x D327 mm weight (actual measurement) 12.2 kg
The price has been reduced! 2024/5/25 sales price 69,800 yen Manufacturer maintained! Rotel's pre-main amplifier. The successor to the company's RA-1062. A full-scale design that uses WBT terminals and other parts that cost more than the price. The unobtrusive and refreshing sound quality is compatible with a wide variety of genres. As for the exterior, there is a feeling of use such as scratches and dullness on the top plate. Serial 867-3031022 (Tomonori Asaine)
Maintenance information: Maintained on 2024.5.24 (volume rotation improvement implemented. Speaker relay contacts have deteriorated (both A/B), B has been replaced, and A improvements have been implemented. (Other maintenance carried out)
Accessories: remote control power cord
Main specifications: 75W+75W with MM input W431 x H99 x D358 mm 8.7 kg