*Currently sold. DAITO Voice 16cm full range unit. If you were looking for it, please go ahead (Kobayashi Hitoshi)
Maintenance information: 2024.5.27 Operation confirmed
Accessories: original box
Main specifications: 8Ω 10W maximum 15W 16cm full range
LUXMAN MC cartridge demagnetizer is easy to use. Plug in the cartridge shell, press the switch, and the 2 indicators go off, and you're done. *Never use MC cartridges or MM cartridges that use print coils. (FUJISAWA KOSHI)
Maintenance information: 2024.5.27 Operation confirmed
Accessories: original box
Main specifications: W120×H44×D56mm 250g
Everything from exterior painting to driver gap cleaning has been refreshed and maintained with attention to detail! 4343 original unit, 4343GY by All Alnico! A famous machine that clearly expresses a rich low-frequency sound and a sense of depth, and continues to be popular even now. The dynamic sound typical of JBL has been revived due to maintenance. It is a famous monitor that can best reproduce sound sources recorded with on-microphone regardless of age or genre. Serial 14004/14414 (Takasaki Atsushi)
Maintenance information: 2023.4.17 Maintained (exterior repair/gray paint,
Front and rear baffle repair/coating, saran net replacement, frame repair, woofer maintenance (edge replacement, cone paper coating), mid maintenance (edge replacement, cone paper coating), driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound absorbing material replacement, terminal contact cleaning), tweeter maintenance (horn disassembly cleaning, magnetic circuit rust removal/gap cleaning, terminal contact cleaning), Network maintenance (damaged terminal (x1) replaced from stock parts. Terminal rust removal, pickling, insulation bush & mounting screw replacement. There is evidence that the ATT was replaced by the user, but the round ATT was replaced with a new one with a square ATT with high power, the large ATT was disassembled and cleaned, contact grease was applied, and the wiring was re-soldered. INT/EXT switch-over SW contact cleaning A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check input/output waveform and balance, check sound output), detach the unit)
Accessories: saran net, diffuser
Main specifications: 4 way 4 speaker bass reflex type 2405/2420/2121/2231A crossover 300Hz/1250Hz/9500Hz 8Ω 93dB W635 x H1,051 x D435 mm 83.9 kg/book
From exterior painting to gap cleaning, it has been refreshed and maintained with attention to detail! This is a 612C monitor speaker with a refined masterpiece 612A system. The unit is an early model 604-8G. The thick, unsluggish tone centered around the middle range is perfect for vocals. Since localization is also precisely determined, it is a practical and easy-to-use speaker (Takasaki Atsushi)
Maintenance information: 2024.2.8 Maintained (exterior repair/polishing/full painting, network mounting hole processing, saran net replacement. Unit maintenance (gasket replacement, input terminal contact cleaning, high frequency side disconnection repair/magnetic circuit rust removal/gap cleaning/center adjustment) network maintenance (frequency characteristic check, panel float bonding, ATT disassembly cleaning, input terminal contact cleaning) terminal cleaning)
Accessories: saran net
Main specifications: coaxial 2-way speaker unit 38cm coaxial impedance 8Ω 104dB crossover frequency 1.5kHz W648 × H749 × D509 mm 54.5 kg
The price has been reduced. 2024/5/26 sales price 228,000 yen 2023/10 manufacturer maintenance completed! The flagship stereo power amplifier model with a KT120 push-pull configuration by Sun Valley. An output transformer with a bifiler-wound custom-made by Hashimoto Electric is used. It achieves both a wide range of sound that is pleasant to listen to. This is a powerful power amplifier that can make even vintage speakers sound with modern speakers. The exterior is dull (Hiura Katsuji)
Maintenance information: 2023.10.20 manufacturer maintenance (PT replacement with a brand new product, carrying out energization after returning the remodeled point to a normal state, measurement of voltage of each part and measurement of various characteristics, music playback test)
Accessories: power cable
Main specifications: used vacuum tube KT120 push-pull 55W+55W KT120 x 4 (TUNG-SOL), 12BH7A x 4 (ELECTRO HARMONICS), CV4003 x 2 W400 x H380 x D220 mm 32 kg
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are small scratches on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: instruction manual, power cable, original box
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are small scratches on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: instruction manual, power cable, original box
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
What an analog cleaning type LP cleaner that is cleaned by manually rotating the disc in a circle. A brush is attached to the inside of the main unit to scrape out dirt from the grooves. There are hardships, such as being hard to spin, getting your hands dirty, etc., but it seems to be a fun cleaning job. The drying stand is missing. We cannot guarantee the quality of the included cleaning solution (Murakoshi Yoichi)
Accessories: special cleaning solution, label protect cover, filter funnel, original box, instruction manual (German)
Main specifications: W336 x H182 x D84 mm 2.2 kg
*Currently sold. The output has been changed to an RCA female terminal. FR MC boost transformer using a toroidal core. Create a natural sound that makes it easy to understand the characteristics of cartridges. In addition to switching the impedance of 10 to 30 ohms, there is also a bypass position, so it is compatible with various cartridges without taking up much space. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 Operation confirmed
Accessories: copy of instruction manual, connection cable
Main specifications: impedance 10 ohm/30 ohm/PASS playback frequency band 20 Hz to 30 kHz W64 x H64 x D105 mm approx. 455 g
Carefully maintained, including replacing glass panels with new ones! An original C22, a famous machine admired by enthusiasts. The thick, soft, and strongly extruded tone is a pleasant tone that can only be experienced with an old McKinn. It has a rich tone centered around the middle range with a high concentration, and it sounds with plenty of realism. The legs are alternative rubber feet (adhesive). You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 maintained (vacuum tube cover, replacement, front panel replacement, 0.01 μF, etc., replacement, 6 electrolytic capacitors, 40 μF replacement, resistance, 1 W and 1/2 W replacement, 8 switching noise improvement measures, 1/4 W, 6 additional resistors, vacuum tube socket and RCA jack, re-caulking repair, etc. Operation checked with AC 100 to 117 V (if you are concerned about sound leakage when volume is minimal, on the top Please narrow down OUT LEVEL))
Accessories: copy of instruction manual
Main specifications: 117 V specification, 4 input systems, 2 phono systems, frequency characteristics, 20 Hz to 20 kHz (± 0.5 dB), signal-to-noise ratio, 85 dB (high level), 62.5 dB (low level), distortion ratio 0.2%, W406 x H138 x D330 mm, 7.3 kg
Maintained. With a 7000 Hz crossover, this network is ideal for tweeters such as 075 and 077! Please enjoy using it in a way that suits your needs, such as 2 way or 3 way. Exterior, paint deterioration and peeling, dullness, and feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 maintained (terminal replacement, terminal cleaning (coil replacement) attenuator VR replacement, crossover 7000 Hz check OK)
Accessories: none
Key Specifications: Variable Level Control Crossover Frequency 7kHz 8Ω Weight 900g
※Since it is a commercial device, there is no problem with the as-is operation, but since there is no guarantee, it is inexpensive. The sound quality is clean, fresh, and light, and the sound is firm and crisp. The sound development is such that the image that comes to mind when using the word YAMAHA for commercial use fits perfectly. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 Operation confirmed
Accessories: copy of instruction manual, power cord
Main specifications: stereo output 105W+105W (4Ω) 100W+100W (8Ω) bridge output 210W (8Ω) frequency characteristics 20Hz-50kHz damping factor 200 input terminal XLR, phone, output terminal 5WAY binding post power consumption 150W W480 x H880 x D456mm 12 kg
Victor's AV selector 4 inputs 1 output The exterior has a feeling of use such as dirt, scratches, and smudges (Kanai Hidetsugu)
Maintenance information: 2024.5.23 continuity confirmed
Accessories: none
Main specifications: W169 x H40 x D78 mm 200 g (actual measurement)
※It is inexpensive because it has a lot of feeling of use. A classic disc stabilizer. The moderate weight gives a sense of stability for playing records. The exterior has a feeling of use such as fading due to aging (Kanai Hidetsugu)
Accessories: none
Main specifications: diameter 80 mm height 35 mm dead weight approx. 600 g
Unspecified speaker stand. Recommended for 4312 and NS1000M size speaker users. There is a feeling of use, such as line scratches scattered on the top plate (Kanai Hidetsugu)
Accessories: none
Main specifications: main body W400 x H220 x D350 mm 5.8 kg (actual measurement) top plate W360 x D320 mm (actual measurement)
The disposal price has been reduced. Member discounts are not applicable. 2024/5/25 sales price 248,000 yen It now uses Alnico, which can be called premium, and the tuning that emphasizes musicality that is comfortable to listen to throughout the entire area makes a good impression. The visuals are also compact and elegant, and have a sense of luxury. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 Operation confirmed
Accessories: saran net, jumper cable
Main specifications: 2WAY sealed 35mm pure silk ring diaphragm tweeter 170mm Kurt Mueller cone woofer rated input 50W maximum input 150W output sound pressure level 87dB impedance 6Ω crossover 3,500 Hz playback band 40 to 50,000 Hz W224 x H380 x D319 mm 10.8 kg
Maintained! Although it is a transistor amplifier, it has a warm sound like a vacuum tube with a faint scent. While it is glossy, it is also strong, so you can use it with any speaker. Exterior, dullness, scuff marks, rust, corrosion, etc. can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 Maintained (main amplifier circuit fault repair fuse replacement. Switch and volume affinity correction)
Accessories: none
Main specifications: 80W+80W (8Ω) W466 x H181 x D378 mm 15 kg
*Remote control is out of stock. Maintained! Onkyo's unique supercurrent amplifier configuration is used for the power section, and the smooth sound is impressive with a circuit that combines a MOS FET and a bipolar transistor. The sense of power in the low frequencies and the extension in the high frequencies play a slightly different sound from the others. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 Maintenance completed (switch disassembly, contact polishing, contact cleaner application. Soldering correction for each circuit board)
Accessories: instruction manual
Main specifications: 80W+80W (8Ω) W455 × H170 × D430 mm 17 kg
8000 Hz network for high range It can also be used in combination with JBL 077 or when combining a full range with a tweeter. Exterior, paint deterioration and peeling, dullness, and feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.25 maintained (terminal terminal deterioration replacement, terminal cleaning (coil replacement) attenuator VR replacement, crossover 8000 Hz check OK)
Accessories: none
Key Specifications: 2 Way Variable Level Control Crossover Frequency 8kHz 8Ω Weight 0.9 kg
The price has been reduced. 2024/5/25 sales price 29,800 yen. ※There is slight distortion, but I don't mind playing music. Altec's 10cm full range unit is rarely in stock. An ALTEC unit with an orthodox design suitable for bass reflex. Please enjoy the speedy sound unique to ALTEC. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 operation confirmed (slight distortion, no problem with music playback)
Accessories: instruction manual, gasket
Main specifications: inch screw pitch, 120 mm, playback frequency characteristics, 130 to 14,000 Hz, efficiency: 94 dB, impedance: 7 ohms, weight: 0.8 kg
Tannoy rectangular yoke type enclosure by Shinkosha, a popular domestic box manufacturer. It is attractive because it is made to sound good. A 30cm unit adapter (detachable) is attached to the baffle surface, and casters are attached to the bottom (Murakoshi Yoichi)
Accessories: none
Main specifications: W597 x H108 x D37 mm weight 30 kg
The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance even when combined with various woofers and tweeters. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Takasaki Atsushi)
Maintenance information: 2024.5.24 sound output confirmed
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms (measured 10/12 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
The price has been reduced. 2024/5/23 sales price 22,800 yen. Set of 4 large insulators The weight capacity is 60 kg, and the height can be adjusted by 7 mm. Please use it under the foot of a rotating device such as a record player. There is a feeling of use such as dirt (Takasaki Atsushi)
Accessories: none
Main specifications: load resistance 60 kg diameter 10 x height 50 mm weight 425 g per piece
※It is inexpensive because there are many stains. A classic shell made from machined aluminum blocks. I like the sturdy construction and simple design (Murakoshi Yoichi)
Maintenance information: 2024.5.21 continuity confirmed
Accessories: none
Main specifications: machined aluminum block body weight 13g
Maintained in 2015. The 606 is thick and unimaginable from its compact exterior. The good sound unique to QUAD allows you to enjoy not only classical music, but also jazz vocals in a mild way. The high level of musicality that makes you enjoy the music with a pleasant tone stands out. There is deterioration in exterior paint (Murakoshi Yoichi)
Maintenance information: 2015.9.12 maintenance completed (internal power transfer → malt plane deterioration → dismantling and reinstallation, exchange of both channel in-board bypass C, gain setting C, etc., TR check → OK, operation inspection check)
Accessories: power cord
Main specifications: output 140W+140W (8Ω) W321×H140×D238mm 12kg
The disposal price has been reduced! (Member prices are not applicable) 2024/5/23 sales price 148,000 yen This is a Venere series bookshelf model designed with a sharp form, breaking away from conventional classical styles. It is a speaker with an excellent glossy, smooth high frequency, and you can enjoy a particularly beautiful sound with stringed instruments and vocals. Serial 0077513 0077513 (Yamato Yuki)
Maintenance information: 2024.5.23 Operation confirmed
Accessories: Saran net original box jumper plate
Main specifications: Wave reflex bookshelf type unit tweeter 29 mm high resolution silk soft dome woofer 180 mm cone type frequency characteristics 45 Hz to 25,000 Hz output sound pressure level 88 dB/w/m 6 ohms size W246 x H449 x D336 mm 7.0 kg (1)
※Whether it is a genuine product is unknown. Set of 8 1 pair of JBL speaker mount parts There is a lot of feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
A backload type enclosure that can mount an unspecified JBL38cm woofer. The construction is solid. If you've been looking for one, take this opportunity. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: saran net
Main specifications: W603 x H1100 x D508 mm 40 kg (actual measurement)
*Some SP terminal plates and screws on the OUT side are missing. A full-range speaker with a high BOSE interior. An indoor speaker with high efficiency and clear sound quality. It is optimally designed for low-volume background music. The exterior has yellowness, dullness, dirt, scratches, etc., and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: mounting hardware, instruction manual
Main specifications: 5.7 cm full range driver x 1 allowable input 16 W impedance 8 ohms maximum sound pressure level 96 dB playback frequency band 90 Hz to 16 kHz W251 x H125 x D119 mm mass 1.8 kg
Currently sold. The tuner's auto tuning is not working, but the current situation is. This K series CD/USB receiver is compatible with playback of iPods/iPhones, USB memory devices, etc. This is a flat, unobtrusive amplifier with a straightforward sound. It can also be connected to a PC and is recommended for those who want to get started with desktop audio. Appearance, dullness, small scratches, and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 operation confirmed (tuner auto tuning not working, other operations confirmed)
Accessories: remote control, power cord
Main specifications: 50W+50W W245 x H104 x D309 mm weight 5.7 kg
The classic 101 mm small speaker. The sound, which has been compiled in one small full-range shot, makes all kinds of popular music sound cheerfully. The exterior and color are different due to discoloration of the saran net, and overall a feeling of use such as dullness, abrasions, etc. can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: none
Main specifications: 1 way 1 speaker impedance 6 ohms maximum input 150 W output sound pressure level 86 db W232 x H154 x D172 mm 2 kg
*Some SP terminal plates and screws on the OUT side are missing. A full-range speaker with a high BOSE interior. An indoor speaker with high efficiency and clear sound quality. It is optimally designed for low-volume background music. The exterior is dull and has scratches (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: mounting hardware, instruction manual
Main specifications: 5.7 cm full range driver x 1 allowable input 16 W impedance 8 ohms maximum sound pressure level 96 dB playback frequency band 90 Hz to 16 kHz W251 x H125 x D119 mm mass 1.8 kg
Crossover 180 Hz board Compatible with the company's channel divider F-5/F-15/F-15L. The attenuation slope can be changed to -12 dB/oct and -18 dB/oct with an internal switch. The exterior is good, with a slight dullness (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: original box
Main specifications: attenuation characteristics -12 dB/oct, -18 dB/oct switching compatible models F-5/F-15/F-15L
The price has been reduced. 2024/5/20 sales price 15,000 yen. Crossover 5000 Hz board Compatible with the company's channel divider F-5/F-15/F-15L. The attenuation slope can be changed to -12 dB/oct and -18 dB/oct with an internal switch. The exterior is good, with a slight dullness (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: original box
Main specifications: Attenuation characteristics: -12, -18 dB/OCT switching 5000 Hz
Frequency board for Accuphase channel dividers F-5, F-15, and F-15L. It is for crossovers 1200 Hz. The exterior is good with a dullness (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: original box (for CB350)
Key Specifications: Crossover 1200Hz Chandeber Board
This is an orthodox cable for 6.0m pair entry for speaker cables. The wire is soft and easy to handle. The exterior is dirty, dull, etc. (Takasaki Atsushi)
Maintenance information: 2024.5.19 continuity confirmed
Accessories: none
A FOSTEX HA21 throat adapter is set on a self-made horn that is a size imitation of the FOSTEX H320. If you've been looking for this size, take this opportunity! You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: throat diameter 100 mm pitch 4 holes 60 mm 3 holes 50 mm overall W635 x H110 x D 455 mm kg (actual measurement)
*Currently sold. JBL/UREI professional power amplifier Dynamic sound with clear contours and momentum. The driving power that makes it easy to drive even large speakers at a high volume is attractive. It can also be used as mono power by connecting to a bridge. There are conspicuous abrasions on the exterior and top plate, and a feeling of use such as dullness and scratches can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: none
Main specifications: 150W+150W (8Ω) 300W+300W (4Ω) input 2 systems (phone/XLR) W483 x H180 x D260 mm approx. 20 kg
*Needle cover missing. Elliptical type with built-in boost transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior has small scratches, dullness, and a feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.5.17 sound output confirmed
Accessories: none
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
The price has been drastically reduced. 2024/5/17 sales price 148,000 yen B&W middle class “tweeter on top” model from the new commercial series. You can enjoy high-response sounds and vivid and realistic spatial expressions. In addition to large dents on one side, there is a light feeling of use and dullness (Murakoshi Yoichi)
Maintenance information: 2024.5.16 sound output confirmed
Accessories: saran net, instruction manual
Main specifications: 8Ω 88dB 45Hz to 50kHz W200 × H403 × D301 mm weight 8.9 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/5/17 sales price 128,000 yen ※Depending on the arm base, the mounting position of the arm is slightly close to the shaft side. Since the arm is long, please remove the dust cover for playback. Comes with SAEC arm stabilizer AS-500! A record player that is highly regarded for its smooth rotation and the effectiveness of the insulator's suspension. The WE-308 arm features a double knife edge for sharp sound and accurate sound image localization. It is a combination of LUX's smooth and quiet motor and SAEC arms that cut sharply into the sound source, so you can fully enjoy the fun and depth of analog. Additional rubber feet have been attached to the legs to prevent the AS-500E. The exterior is dull and has small scratches. Serial G8903281 (Murakoshi Yoichi)
Maintenance Information: 2020.6.2 Maintained (created with strobe circuit LED. diode installation. Electrolytic capacitor replacement. Power circuit film capacitor replacement. (Inside Force cancellation weight exchange)
Accessories: phono cable
Main specifications: PD-131 direct drive system 8 pole 24 slot brushless DC servo motor W472 x H160 x D372 mm weight 12 kg WE-308 double knife edge static balance universal type total length 329 mm effective length 240 mm overhang 5 mm needle pressure 0 to 2 g cartridge weight range: 5.5 to 12.5 g
This is a standard JBL monitor that has undergone internal and external maintenance and has been refreshed. The darker and thicker tone compared to the current model still doesn't even seem to be declining in popularity. The thick, exhilarating sound goes well with jazz and rock, and the punchy sound is captivating. The exterior has been beautifully finished due to maintenance. Serial 32547 32298 (Murakoshi Yoichi)
Maintenance information: 2024.5.16 maintenance (exterior repair/cleaning, saran net cleaning, repasting, ATT cleaning)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system frequency characteristics 45 Hz to 20 kHz sound pressure level 93 dB impedance 8 ohms allowable input 100 W dimensions W362 x H597 x D298 mm weight 20 kg/1
The price has been drastically reduced. 2024/5/17 sales price 24,800 yen. Q ACOUSTICS 2-WAY BOOKSHELF. Once the setting is decided, you can enjoy a variety of music genres with a sense of scale that makes you doubt the size. There are dents around the upper corner on one side, and there is slight dullness throughout (Murakoshi Yoichi)
Maintenance information: 2024.5.16 sound output confirmed
Accessories: saran net, rubber feet
Main specifications: 2 way 6Ω 88dB W170 × H260 × D226 mm 4,6 kg