Power transformer hammer tone color primary: 100V/FUSE1A secondary: 280-250-0-250-280V/AC0.12A 5-6.3V/2A 6.3V/1.5A x 2 W85 x H76 x D71 mm approx. 2.3 kg (actual measurement, not including protrusions) (Kojima Yosuke)
The flagship model of the Macintosh power amplifier with a silver panel. It is characterized by its rich sound. The extrusion is strong and goes great with JBL large monitor speakers. The dynamism in the mid to low range, which is difficult to obtain with current Mackin power amplifiers, is attractive. There are scratches, dullness, and discoloration in places (Kojima Yosuke)
Maintenance information: Maintained on 2020.8.26 (2 input volumes, 4 semi-fixed volumes, 2 RCA plugs, 12 lamps, 8 electrolytic capacitors, replacement input mode switch disassembly cleaning, card edge cleaning, soldering, bias and offset check, output sound check)
(*The interior and exterior have been cleaned.)
Accessories: power cable
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
Pair tube EL34 compatible sphere made in Japan black plate measured value 54/54 (rejected value 30) with white box, the printing design is different on the left and right, but the internal structure is the same ※Pairs are judged based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Choke transformer 0.9 H/260 mA DC resistance 26.8 ohm (actual measurement) choke transformer mounted on A3600, etc. W55 x H71 x D50 mm 0.7 kg (actual measurement, not including protrusions) There are scratches and paint peeling in places (Kojima Yosuke)
Accessories: none
※Sold as 1 piece output transformer for single output 7W hammer tone color primary: 5 kΩ secondary: 4-6-8 Ω W50 x H81 x D58 x 57 mm 0.86 kg (actual measurement, not including protrusions) with original box (Kojima Yosuke)
Accessories: original box
Digital cable, 1.0m, RCA terminal, zero crystal silver conductor, has good sound accuracy for faint sounds, and is characterized by a steady sound. It is a cable that can be obtained at a relatively low price among the company's cables, which have many high price ranges (Kojima Yosuke)
Accessories: none
Speaker cable, 1.5 m pair by wire specification, EQB8, Y lug specification at both ends, 7N-OCC Copper conductor top model, high CP cable with sound quality close to Eclipse 8 while keeping the price low. This cable is excellent for SN and has just the right amount of softness for sound (Kojima Yosuke)
Accessories: special case
Pair tube, ambient heat beam tube, 5881 equivalent tube, made in America, JAN brown base measurement value 42/42 (rejected value 25) with white box ※Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Pair tube EL34 compatible ball, black plate, made in Japan, measured value 54/54 (rejected value 30) with original box ※Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Power transformer hammer tone color primary: 100V/FUSE1A secondary: 280-250-0-250-280V/AC0.12A 5-6.3V/2A 6.3V/1.5A x 2 W85 x H76 x D71 mm approx. 2.3 kg (actual measurement, not including protrusions) (Kojima Yosuke)
Accessories: none
Sold 1 bottle EL34 compatible ball, made in Japan, black plate, measured value 52 (rejected value 30) with original box, there is a slight getter burn ※ pairs are judged based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Power transformer primary: 100V secondary: CT-6.3V/3A x 2, 5-6.3V/3A, 350-310-40-0-310-350V/20mA DC200mA W104 x H92 x D88 mm approx. 4 kg (actual measurement, not including protrusions) There are small abrasions and paint peeling in places (Kojima Yosuke)
Accessories: none
Power transformer primary: 90-100-110V secondary: CT-6.3V/1.2A, 5V/2A, 6.3V/2A, CT-6.3V/1.2A, 250-220-0-220-250V/DC130mA W85 × H68 × D71 mm approx. 1.8 kg (actual measurement, not including protrusions) with original box (with writing on the box) (Kojima Yosuke)
Accessories: original box
※Only 1 output transformer push-pull output primary: 4 kΩ Secondary: 4-8-16 Ω W53 × H65 × D69 mm 0.8 kg (actual measurement, not including protrusions) There are paint peeling and rust spots in places (Kojima Yosuke)
Accessories: none
MC cartridge compatible with EMT arms by attaching the SPU body and Audiocraft adapter OF-3A to the modified headshell. You can enjoy the gorgeous and expansive sound typical of an orthophone with the EMT arm. The cantilever is moving very slightly to the right (Murakoshi Yoichi)
Maintenance information: 2024.5.10 sound output confirmed
Accessories: none
Main specifications: MC type output 0.2 mV for EMT arms, proper needle pressure 4 g, internal impedance 2 ohms, dead weight 24 g
GT SONIC's compact ultrasonic cleaner for commercial use. It's not for audio only, but it seems that it can be used for quite a variety of purposes. I think the size is good too. If you've been looking for one, take this opportunity. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: power cord, original box
Main specifications: ultrasonic power consumption 150 W power supply AC 100-120 V 50/60 Hz ultrasonic frequency 40,000 Hz cleaning tank size: W155 x H150 x D300 mm body size: 180 x 310 x 330 mm 5.9 kg
XLR cable 3ch line selector High quality parts are used for the changeover switch, connector, and internal wiring, and the original sound quality is conveyed as it is. You can select up to 3 amplifiers (pre-amplifier or pre-main amplifier) for 1 source device. Also, you can select up to 3 source devices to be switched for 1 amplifier (preamp or premain amplifier). You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 continuity confirmed
Accessories: none
Main specifications: 1 input/3 output systems GND common to all input/output W250 x H64 x D117 mm 2.3 kg
The price has been reduced! 2024/5/16 sales price 99,800 yen Maintained! A speaker that allows you to enjoy the powerful sound of JBL. A vertical twin that uses bi-radial horns for the tweeter and is developed with upper and lower 20cm woofers. Sound pressure, which is characteristic of horns, is uniformly distributed within the area, and you can experience a wide service area. The exterior has been beautifully finished due to maintenance. Serial 5340-015070 5340-015071 (Asaine Tomoho)
Maintenance information: 2024.5.16 Maintained (exterior cleaning/touch-up saran net cleaning/frame repair/paint tweeter maintenance (magnetic fluid removal/cleaning/center adjustment in the magnetic circuit gap, left and right sound pressure difference adjustment, internal urethane replacement) woofer maintenance (edge replacement, gasket preparation and installation) unit detachment)
Accessories: saran net
Main specifications: output sound pressure level 92 dB frequency characteristics 35 Hz to 20 kHz W318 x H965 x D413 mm weight 34 kg
The price has been reduced! 2023/5/16 sales price 9,800 yen ※Currently sold, it is cheap because it is in poor condition. This model has a nicely looking model with units arranged in the center. It has excellent sharpness from low to high frequencies, and is perfect for those who listen to pop music. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 105025A 105025B (Hiroki Aso)
Maintenance information: 2024.5.16 sound output confirmed (good sweep test)
Accessories: saran net
Main specifications: low frequency 18 cm cone woofer high range 3.5 cm dome tweeter impedance 6 ohm allowable input 70W W225 x H370 x D229 mm 5.4 kg/book
Maintained! Original Model 7 You can enjoy a glossy mid to high range sound with a high sense of transparency and a thick, exquisite balance. It's a model that has been over half a century since it went on sale for analog fans, but it's still one they admire. The lustrous, indescribable tone is an appeal that cannot be enjoyed on modern devices. You can see a feeling of use, such as appearance, dullness, small scratches, etc. Serial 7-14836 (Kobayashi Hitoshi)
Maintenance information: 2023.5.20 maintained (balance volume B curve → MN curve replaced, block capacitor, 50 μF x 3, oil capacitor, 0.1 μF, other deterioration replacement, 8 electrolytic capacitors, 200 μF deterioration replacement, 2 vacuum tubes, 12AX7 deterioration replacement, 2 shield case replacement, high pressure selenium deterioration countermeasures → diode addition, side pad deterioration exchange, vacuum tube socket and RCA jack caulking repair, etc. Operation has been checked with AC 100 to 117 V)
Accessories: none
Main specifications: tubular control amplifier, vacuum tube, ECC83/12AX7, 3-stage NF equalizer, NF type step switching control, W453 x H185 x D267 mm, weight 7.5 kg
The price has been drastically reduced. 2024/5/15 sales price 118,000 yen Maintained! A famous direct drive machine representative of Technics. The torque is high, the start and stop times are extremely short, and the stable operation that immediately enters constant speed is unique. It also drives LP heavyweights without difficulty. Overall there are small wounds, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (due to disconnection of the FG coil in the motor core, the FG/ angular velocity detection coil was taken out after disassembling the motor core, and the coil pack was rewound. The rotation speed has been reset)
Accessories: copy of instruction manual, power supply unit
Main specifications: Direct drive aluminum die-cast turntable 33, 45, 78 rotating body W365 x H100 x D360 mm 9.5 kg power supply unit W110 x H85 x D300 mm 3.8 kg
The price has been drastically reduced! 2024/5/15 sales price 148,000 yen The X-DP7, which specializes in DACs, has arrived. By inheriting the performance of the X-DP10 and specializing in DACs, a high signal-to-noise ratio has been achieved. It is also DSD compatible, and it is a high quality car with excellent cost performance. There are no noticeable scratches on the exterior. Serial R10939 (Tamura Eiji)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, instruction manual, power cable
Main specifications: digital input: USB x 1, OPTICAL x 2, COAXIAL x 2, AES/EBU x 1, CLOCK x 1 analog input: RCA x 2, XLR x 2 analog output: RCA x 1, XLR x 1 PCM: 24, 32 bit/44.1, 48, 88.2, 96, 176.4, 192, 352.8, 384, 705.6, 768 kHz DSD: 2.8224, 5.6448, 11.2896 MHz (DoP, (Compatible with ASIO 2.2) W420 x H68 x D320 mm weight 5.9 kg
The price has been reduced! 2023/5/15 sales price 19,800 yen A new-concept connected tap equipped with a surge absorber (lightning protection) and noise filter in one package. It has contributed greatly to further improvements in S/N and sharp sound quality that is transparent yet makes you feel dynamic. There are no noticeable scratches on the exterior. Serial 38600KK042 (Yonejima Satoshi)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
Main specifications: W56 x H35 x D233 mm (including connected outlets) 620 g
The price has been drastically reduced! 2024/5/15 sales price 198,000 yen 800 Diamond series center speaker It is well connected to the Diamond Series due to unit groups that have evolved further from the previous game. High quality mid-range is reproduced. It is a cheap character that can be combined with other speakers for the center. There are thin threads on the exterior. Serial 12120002808 (Yonejima Satoshi)
Maintenance information: 2024.5.15 sweep test good
Accessories: jumper cable
Main specifications: 2-way bass reflex drive unit 25mm diamond dome tweeter x 1, 165mm Woben Kevlar cone FST mid woofer x 1 playback frequency band 42Hz to 33kHz output sound pressure level 88dB nominal impedance 8Ω W486 x H279 x D287 mm weight 12.5 kg
Quadra Spire Center Speaker Stand This stand allows you to adjust the angle according to the listening position. As for the exterior, felt is attached to the bottom (Tamura Eiji)
Accessories: No accessories
Main specifications: W375 x H111 x D290 mm
Maintained! A power amplifier with a characteristic large meter. A straightforward tone with no peculiarities. There is momentum unique to the 80s, and you can enjoy crisp sound quality. It is also ideal as an introduction to separate amplifiers. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2024.5.14 maintained (output relay, meter relay replacement, indicator lamp replacement, meter lamp replacement, volume replacement, operational amplifier replacement, solder repair, interior and exterior inspection and cleaning, operation confirmation)
Accessories: copy of instruction manual
Main specifications: 130W+130W (8Ω) 170W+170W (4Ω) frequency characteristics 1Hz to 100kHz impedance 4Ω to 16Ω W450 × H174 × D422mm 18.5 kg
The price has been reduced! 2023/5/14 Torrens entry model with sales price 118,000 yen. Although it is an entry model, the silence and smoothness of the belt drive, and the delicate sound are attractive, and the tone arm is easy to adjust. Recommended for introductory belt drive machines. There are a few small scratches on the exterior. Serial 00262803 (Fujisawa Yukishi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: copy of instruction manual, power cord, connection cord, spike base, original box
Main specifications: W420 x H125 x D330 mm 8 kg Drive system: belt drive motor: synchronous motor speed: 33 1/3, 45 rpm electronic speed selection platter: diameter 300 mm, 3 kg, aluminum power supply unit housing tone arm: static balance type
A speaker stand with the same texture as the company's NS-1000M. The angle of the midplate can be adjusted to 4 positions according to the low frequency characteristics of the room and speakers. It is ideal for medium speakers such as the NS-1000M. The exterior has scratches and dullness. (FUJISAWA KOSHI)
Accessories: No accessories
Main specifications: W370 x H250 x D290 mm 6.5 kg
The price has been reduced! 2024/5/13 sales price 84,800 yen ※The rubber on the saran net cloth cover is fully stretched, so it's cheap! LINN tall boy speaker. It is a speaker with a relaxed, mature sound like a circle, and the more you listen to it without decoration, the more delicious it is. There is a feeling of use on the exterior due to scratches, dullness, etc. ※The active module is not included. Serial 004963 004964 (Tomonori Asaine)
Maintenance information: 2024.5.13 sweep test good
Accessories: Saran net cloth cover
Main specifications: 3 way 8 ohm maximum input 75 W crossover 2.5 kHz efficiency 87 db W 192 x H900 x D 280 mm 25 kg/book
The price has been drastically reduced! 2024/5/13 sales price 108,000 yen Speaker from Taiwanese manufacturer Usher Audio with a unique design. The mid to high frequencies are delicate and stretchy, and the low frequencies have an attractive, bouncy, and tense sound. It is a model that works very well with current pop and piano sounds when played clearly with a powerful amplifier. There is a feeling of use on the exterior such as small scratches and dullness (Asaine Tomoho)
Maintenance information: 2024.5.13 operation confirmed
Accessories: Saran net spike spike receiving jumper plate
Main specifications: 3-way 3-speaker bi-wire specification 8Ω 87dB 25Hz to 28,000 Hz W350 x H1250 x D650 mm 58.2 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/5/13 Tall Boy with a sales price of 148,000 yen. The woofer uses a wood fiber cone, and the tweeter is equipped with a 28mm dome tweeter and ribbon tweeter. In addition to the conventional mid-high range with a high texture, we have acquired a new low range where you can feel the high response. Serial 1917336 (Murakoshi Yoichi)
Maintenance information: 2024.5.13 sound output confirmed
Accessories: saran net, jumper cable, spikes, metal fittings
Main specifications: 3 way 4 speakers bass reflex type frequency characteristics 49 Hz to 32 kHz efficiency 89 dB impedance 4 ohms W195 x H001 x D330 mm weight 18.9 kg