Kappa series improved model Renaissance 90. The mid-high range is composed of EMIM and EMIT special units, and the sound is extremely delicate and clear. The deep sound field space and glossy, moisturized mid to high frequencies are unique to ribbon units. It has high resolution throughout the entire range and is suitable for classical and vocal styles. There are small scratches and line wounds, and there are repair marks of broken decorative plates at the foot (Oikawa Tetsuji)
Maintenance information: 2013.12.15 Maintained (exterior repair and cleaning. (Back side urethane deteriorated, replaced with substitute urethane)
Accessories: spikes
Main specifications: 4 way 4 speakers sealed floor type EMIT tweeter EMIM mid-range ribbon type 87dB 4Ω 250W W435 x H1245 x D315 mm 35.8 kg
Genuine Baes product. Comes with wood cabinet. A control amplifier representing Mackin's golden age. Compared to the C28, this model has a wider range and more subtlety. The rich, glossy, and thick tone is alive and well, and it plays particularly well with vintage speakers. There are stains and small scratches on the exterior as a whole, and there are bubbles around the knobs of the glass panel and around the SW (Sasaki Shota)
Maintenance information: 2018.3.15 Maintenance completed (each SW/VOL cleaning, *BASS/TRE chips could not be removed. LDR, bridge diode, and illumination lamp replacement. C, R, etc. check, peeling correction only on the upper and lower parts. (*Some corrections are not possible)
Accessories: copy of the manual
Main specifications: frequency characteristics 20 Hz to 20 kHz input terminals PHONO 1 2, AUX, TUNER, TAPE 1, 2 W406 × H138 × D330 mm 8.6 kg
*Currently sold. Comes with enhanced power supply OBH-2. Creek MM phono equalizer. Although it has a compact body, it lets you hear bouncy low frequencies with good pitch. The response of the power lamp is slightly poor, but this is the current situation (Oikawa Tetsuji)
Maintenance information: 2024.5.20 Operation confirmed
Accessories: enhanced power supply OBH-2
Main specifications: Dimensions W100 x H62 x D125 mm Weight 360 g
※Since it has been replaced with an external plug, it is inexpensive. RCA cable, 0.7 m pair, LC-OFC class 1 conductor, has been produced for over 10 years, and is a long-selling product that can transmit pure signals. The balance is an indescribable cable with flat, tight bass and a smooth high-frequency luster. It rubs against the sheath and is dirty (Mizusaki Ryo)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: none
RCA cable, 1.0 m pair, LC-OFC class 1 conductor, is a long-selling product capable of pure signal transmission that has been produced for over 10 years. The balance is a flat, tight bass, and an indescribable cable with a smooth high-frequency luster. There is friction on the sheath, dirt, and deterioration on the plug (Mizusaki Ryo)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: none
RCA cable, 1.0 m pair, LC-OFC class 1 conductor, is a long-selling product capable of pure signal transmission that has been produced for over 10 years. The balance is a flat, tight bass, and an indescribable cable with a smooth high-frequency luster. There is friction on the sheath, dirt, and deterioration on the plug (Mizusaki Ryo)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: none
Woofer edge softening treatment! A mid-size dia-tone speaker. The sound image expressed from precise sound construction is carefully created with diamond tones, making classical music elegant and magnificent. Female vocals etc. are also recommended. There are small scratches, scuffs, and broken corners on the net. Serial 19119, 19433 (Fujisawa Yukishi)
Maintenance Information: 2024.5.20 Maintained (woofer edge softening treatment)
Accessories: saran net
Main specifications: 3 way, 3 speakers, sealed frequency band, 35 Hz to 40 kHz, 6 ohms, sound pressure level, 90 dB, W360 x H808 x D325 mm, 29 kg/book
A fully balanced discrete, non-feedback D/A converter using an independent mono mode that is also equipped with a NOS mode. Equipped with 2 ESS ES9038PRO In addition to being compatible with the latest high-resolution sound sources in various PCM and DSD formats via USB input, it also supports coaxial digital input (2 systems) AES/EBU input. You can enjoy more realistic and natural sounds in NOS mode. There are several dot-shaped dents on the front panel. Serial 190730008 (Fujisawa Yukishi)
Maintenance information: 2024.5.20 Operation confirmed (the mounting solder was fixed because the RCA terminal ground cap came off.)
Accessories: instruction manual, power cord, spike
Main specifications: input format (USB) PCM, DSD (DoP v1.1, ASIO) input format (coaxial/AES/EBU) PCM, DSD (DoP v1.1) compatible sampling frequency (USB) maximum 768 kHz (PCM) /maximum 22.6 MHz (DSD) compatible sampling frequency (coaxial/AES/EBU) maximum 192 kHz (PCM) /2.8 MHz (DSD64 DoP v1.1) PCM quantization Number of bits (USB) 24 bit 32 bit PCM number of quantized bits (coaxial/AES/EBU) 16 bit 24 bit USB profile USB 2.0, USB Audio 2.0 digital input USB (Type B) 2 coaxial (SPDIF) AES/EBU analog output XLR1 system RCA1 system analog output level (XLR) 5.6 Vrms analog output level (RCA) 2.8 Vrms frequency characteristics 2 Hz to 120 kHz (+0/-1 dB) S/N ratio 110 dB total harmonic distortion ratio 0.003% analog filter secondary passive power supply voltage AC 100V 50/60 Hz power consumption 40W size W430 x H109 x D379 mm weight 10 kg
Accuphase F-5/F-15 crossover frequency 12500 Hz board. The exterior is good with a dullness (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: original box
Main specifications: crossover frequency 12500 Hz attenuation characteristics 12 dB/oct・-18 dB/oct switchable
Frequency board for Accuphase channel divider F-5/F-15 The crossover is 800 Hz, which is easy to use! The attenuation slope can be changed to -12 dB/oct and -18 dB/oct with an internal switch. The exterior is good, with a slight dullness (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: original box
Main specifications: F-5/F-15/F-15L crossover 800 Hz attenuation characteristics -12/-18 dB switching
Frequency board for Accuphase channel dividers F-5, F-15, and F-15L. It is for crossovers 1200 Hz. The exterior is good with a dullness (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: original box (for CB350)
Key Specifications: Crossover 1200Hz Chandeber Board
Non-switching Class A configuration mono power amplifier. It goes great with British speakers, and the fresh, rich, and powerful sound is appealing. It also has a built-in music sensing function that automatically goes into standby state (green) when the input signal is interrupted for a certain period of time, and turns on the power (red) when the signal comes back in. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: power cord, original box
Main specifications: 100W+100W 8Ω W160×H100×D350mm 5.0 kg
500Hz/2 way board included. Accuphase 2-way/3-way channel divider. You can change the crossover by replacing the board. It is one of the few channel dividers where you can enjoy multiple systems while retaining an analog feel. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: power cable, CB500, CB-2WAY
Main specifications: 2 way/3 way divider frequency fixed type W445 x H109 x D373 mm 9.1 kg
Maintained by the manufacturer! A special edition model of VRDS-10. This is the only TEAC player model that uses a Philips TDA1547 as a D/A converter. The sound quality is not sharp due to the hardware of VRDS, and the sound quality is well-balanced, which brings out the characteristics of the relaxed DAC7. The exterior has small scratches and a feeling of use such as dullness. ※There is a noticeable scratch on the front panel. Serial 30300 (Yamato Yuki)
Maintenance information: 2024.4.26 Maintained (inspection of each part carried out, tray belt clamp, belt turntable bearing wear, replacement pickup, and mechanical part cleaned and lubricated.
(Check operation)
Accessories: instruction manual copy remote control (for VRDS-15)
Main specifications: 2-channel CD player frequency characteristics 1 Hz to 20 kHz 8 times oversampling 20 bit digital filter W442 x H149 x D331 mm 11 kg
Comes with original box! Digital needle pressure gauge for analog record players. Compatible with measurements from 0.01g to a maximum of 200g. The tray has a layout that makes it easy to place needles. The LCD screen is backlit and equipped with an auto off function. The exterior has a feeling of use such as dullness (Hiroki Aso)
Maintenance information: 2024.5.20 Operation confirmed
Accessories: none
Main specifications: AAA battery specification W93 x H17 x D115 mm dead weight 115.5 g
Self-made 4ch power amplifier using 4 Flying Mall digital power amplifiers DAD-M1. The construction is solid, and the sound is high resolution, just like a flying mall. Recommended for those who want to save space and use it for multiple purposes. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.20 sound output confirmed
Accessories: power cable
Main specifications: DAD-M1 rated output 160W/4Ω 100W/8Ω frequency characteristics DC to 25kHz/4Ω DC to 50kHz/8Ω S/N ratio 120dB overall size W270 × H162 × D290 mm weight 6 kg (actual measurement)
Self-made 4ch power amplifier using 4 Flying Mall digital power amplifiers DAD-M1. The construction is solid, and the sound is high resolution, just like a flying mall. Recommended for those who want to save space and use it for multiple purposes. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.20 sound output confirmed
Accessories: power cable
Main specifications: DAD-M1 rated output 160W/4Ω 100W/8Ω frequency characteristics DC to 25kHz/4Ω DC to 50kHz/8Ω S/N ratio 120dB overall size W270 × H162 × D290 mm weight 6 kg (actual measurement)
RCA cable 2.0m pair LC-OFC Class 1 is a long-selling product capable of pure signal transmission that has been produced for over 10 years. The balance is impressive with flat, tight bass and smooth high-frequency luster. The exterior is dull and has a feeling of use (Hiroki Aso)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: none
In January 2023, both the interior and exterior were maintained and brushed up! ORIGINAL LANSALOY EDGE! The OLYMPUS S8R representing JBL has arrived. The 075 tweeter is full of realism, with the sound of a driver blowing fire into the thick, dry low frequencies, and a sense of realism that leaves graininess. You can enjoy the real thrill of vintage audio. Outside of the exterior, the back plate on one side is missing, and the finish is beautiful due to maintenance (Kobayashi Hitoshi)
Maintenance information: 2023.1.10 maintenance (exterior repair, polishing, baffle/hakama repair before and after oil finishing, painting, lattice repair, polishing, painting, lining replacement. Woofer maintenance (edge softening treatment, corn paper coating, passive corn paper coating). Driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound-absorbing material replacement, terminal contact cleaning). Tweeter maintenance (horn disassembly/polishing, magnetic circuit rust removal/gap cleaning, terminal contact cleaning). Network maintenance (LX5: terminal rust removal, acid washing, insulation bush & mounting screw replacement. ATT (SW type) disassembly contact polishing and cleaning. Reinforced with silicone to prevent the coil from coming off. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. N7000 terminal rust removal, acid cleaning, insulation bush, and mounting screw replacement. ATT replacement with a brand new one. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check input/output waveform and balance, check sound output))
Accessories: saran net, diffuser, instruction manual
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1020 x H670 x D510 mm weight 82 kg
The price has been reduced. 2024/5/18 sales price 178,000 yen Pickup replacement included manufacturer maintenance! It is a CD player designed with the concept of a D/A converter equipped with a CD transport. Switching is possible with the 44.1/96/192 kHz upsampling buttons. It is characterized by a comfortable sound quality that combines highly textured softness and freshness. There are dents on the exterior and front panel, and a feeling of use such as dullness and abrasions can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.18 manufacturer maintenance (pickup replacement, operation confirmation)
Accessories: remote control, power cord
Main specifications: CD player equipped with digital input, uses a PHILIPS VAM1201MK3 mechanism, supports upconversion to 24 bit/192 kHz (CD playback, external input) digital output/light 1, coaxial 1, W435 x H73 x D345 mm, 7.2 kg
It is a model that has completely renewed all units in the JBL 4312 series control monitor, which has continued for over 30 years. In addition to the vibrant sound with a high sense of freshness, which is characteristic of the series, the expansion of the high frequency range is remarkable. The exterior has a feeling of use such as dullness. Serial 0261 0440 (Tomonori Asae)
Maintenance information: 2024.5.16 sound output confirmed (good sweep test)
Accessories: saran net
Main specifications: 3-way bookshelf type frequency characteristics 40Hz to 40kHz crossover 2kHz/5kHz 6Ω output sound pressure level 93 dB W362 x H597 x D301 mm 18.1 kg
Comes with original box! LUXMAN's classic line selector. It is an easy-to-use and convenient model that outputs from 1 input system to 4 systems, and conversely, outputs from 4 input systems to 1 system. Fairly good condition. Serial 2509-1G2 (Fujisawa Yukishi)
Maintenance information: 2024.5.18 continuity confirmed
Accessories: instruction manual, original box
Main specifications: 1 system, 4 systems input/output W160 x H65 x D95 mm, 530 g
※The dust cover is missing. Maintained! Sony's first fully automatic player. Equipped with a biotracer that electronically controls all complex movements of the tone arm. An ambitious Japanese work packed with every gadget imaginable at the time! Needle pressure can be adjusted simply by controlling the knob on the front panel, and the applied needle pressure value is digitally displayed. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.2.27 Maintained (main unit internal inspection grease coating, cleaning) *At low temperatures, an offset will occur when the arm is forcibly fed by manual operation. The current situation is that stable operation is not possible unless the room temperature or the temperature inside the main unit rises to a certain extent (room temperature).
Accessories: none
Main specifications: Crystal Rock D.D. Fully automatic player system, needle pressure adjustment range 0.5 g to 3.0 g, W500 x H175 x D430 mm, approx. 15 kg
The price has been drastically reduced! 2023/5/16 sales price 118,000 yen with LS STAND 70 (list price 48,000 yen). This model won the Audio Famous Equipment Award 2005 Speaker System Small Category Award. An excellent balance between the robustness of the enclosure and the suppleness of the unit group. A practical model with attractive spatial expressiveness and accurate sound images that don't make you aware of the presence of a speaker. There are scratches and bumps on the exterior. Serial 37038E002557/37038E002558 (Yonejima Satoshi)
Maintenance information: 2024.5.15 sweep test good
Accessories: instruction manual saran net spike fixing screw
Main specifications: 2-way bass reflex woofer 115mm aluminum hybrid cone tweeter JETIII crossover frequency 3,000 Hz input rating 70W/maximum 90W frequency characteristics 42-50,000 Hz efficiency 86dB impedance 4Ω dimensions W123 x H208 x D282 mm (when grille attached) weight 6.5 kg LS STAND 70: H700 x W240 x D290 mm top plate W75 × D210mm weight 6kg/set
The price has been reduced. 2024/5/19 sales price 148,000 yen A typical woofer attached to first-class products such as Exclusive2402 and Westlake Audio. It is a highly stable model that can withstand professional use. The response speed is fast and the sound that makes it stand up well is attractive. There is a light stain on the corn paper (Murakoshi Yoichi)
Maintenance information: 2024.5.17 sound output confirmed
Accessories: none
Main specifications: 40cm cone woofer frequency characteristics 28 Hz to 1000 Hz 8 ohms (measured 7.9 ohms) output sound pressure level 97 dB dimensions diameter 400 mm x depth 167 mm 11 kg/1
The price has been drastically reduced! 2024/5/13 sales price 108,000 yen Speaker from Taiwanese manufacturer Usher Audio with a unique design. The mid to high frequencies are delicate and stretchy, and the low frequencies have an attractive, bouncy, and tense sound. It is a model that works very well with current pop and piano sounds when played clearly with a powerful amplifier. There is a feeling of use on the exterior such as small scratches and dullness (Asaine Tomoho)
Maintenance information: 2024.5.13 operation confirmed
Accessories: Saran net spike spike receiving jumper plate
Main specifications: 3-way 3-speaker bi-wire specification 8Ω 87dB 25Hz to 28,000 Hz W350 x H1250 x D650 mm 58.2 kg
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
The price has been reduced! 2024/5/16 sales price 99,800 yen Maintained! A speaker that allows you to enjoy the powerful sound of JBL. A vertical twin that uses bi-radial horns for the tweeter and is developed with upper and lower 20cm woofers. Sound pressure, which is characteristic of horns, is uniformly distributed within the area, and you can experience a wide service area. The exterior has been beautifully finished due to maintenance. Serial 5340-015070 5340-015071 (Asaine Tomoho)
Maintenance information: 2024.5.16 Maintained (exterior cleaning/touch-up saran net cleaning/frame repair/paint tweeter maintenance (magnetic fluid removal/cleaning/center adjustment in the magnetic circuit gap, left and right sound pressure difference adjustment, internal urethane replacement) woofer maintenance (edge replacement, gasket preparation and installation) unit detachment)
Accessories: saran net
Main specifications: output sound pressure level 92 dB frequency characteristics 35 Hz to 20 kHz W318 x H965 x D413 mm weight 34 kg
The price has been reduced! 2024/5/18 sales price 7,000 yen ※There is no problem with operation, but since it is cheap, it is being handed over as is. A speaker that uses a silk OMF diaphragm. The response is fast, and the mid to high range sound is produced well. The impression is that it is suitable for female vocals, jazz pianos, etc., and has a luxurious real wood veneer finish. Serial 5990510607/5990510607 (Tomoho Asaine)
Maintenance information: 2024.5.17 Operation confirmed
Accessories: saran net
Main specifications: 2-way bass reflex, 4 ohms, frequency band 45 Hz to 35000 Hz, W180 x H305 x D270 mm, 5.1 kg
The price has been drastically reduced! 2024/5/16 sales price 598,000 yen A speaker system that enables sound reproduction with excellent transparency and total balance by adopting the same unit with the know-how of the advanced model Ascent. The three-dimensional space radiated from AVALON's unique enclosure and the surprisingly clear sound image with high resolution are still alive and well here. Sound quality that doesn't make you aware of the presence of speakers has created a unique world. There is a feeling of use on the exterior due to small scratches, sunburn, dullness, etc. (Asaine Tomoho)
Maintenance information: 2024.5.16 sound output confirmed (good sweep test)
Accessories: instruction manual saran net jumper cable (general purpose product)
Main specifications: 2-way, 2 speakers, sealed system, floor type, unit used: bass/22cm cone type, treble/2.5cm titanium dome type Playback frequency band: 35 Hz to 24000 Hz ± 1.5 dB crossover frequency: unannounced impedance: 6 ohms output sound pressure level: 86 dB (2.83 V, 1 m) W279 x H991 x D381 mm 43 kg
The price has been reduced! 2024/5/18 sales price 79,800 yen ※It's cheap because the saran is torn or the speaker terminal LF+ on one side does not tighten until the end. Slim tall boy speaker MONITOR AUDIO's middle class, SILVER series, is now in stock. The RS8 has a delicate, highly clear mid to high range tone with good tightness in the low range. The owner has well-balanced characters that can be used from the living room to the tatami room. In addition to dullness and small scratches on the exterior, there is a feeling of use such as a tear on the saran net and sunburn on the main body. Serial 801702/801702 (Tomonori Asae)
Maintenance information: 2024.5.17 sound output checked (good sweep test)
Accessories: Saran net jumper cable (general purpose)
Main specifications: Format: 2.5-way 4 speakers, floor type (anti-magnetic), front & rear port, bass reflex impedance, 6 ohms, allowable input, 175 W, efficiency, 91 dB, frequency characteristics, 33 Hz to 25 kHz, W185 x H900 x D 270 mm, weight 21.0 kg
*Currently sold. Technics 5cm horn tweeter Uses titanium diaphragms and die-cast aluminum horns. The sound quality is bright and hard with good sharpness. There are scratches and oxidation on the exterior (Yonejima Satoshi)
Maintenance information: 2024.5.19 oscillator test is good
Accessories: No accessories
Main specifications: horn type playback frequency 3,000 to 25,000 Hz W70 x H70 x D60 mm 0.35 kg
The price has been reduced! 2024/5/16 sales price 9,800 yen ※Currently sold, it is cheap because it is in poor condition. This model has a nicely looking model with units arranged in the center. It has excellent sharpness from low to high frequencies, and is perfect for those who listen to pop music. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 105025A 105025B (Hiroki Aso)
Maintenance information: 2024.5.16 sound output confirmed (good sweep test)
Accessories: saran net
Main specifications: low frequency 18 cm cone woofer high range 3.5 cm dome tweeter impedance 6 ohm allowable input 70W W225 x H370 x D229 mm 5.4 kg/book
Maintained! The strength of the extrusion of the entire range and the clear sound are truly sounds unique to the heyday of JBL. The mid-high range with a unique sense of spaciousness and strong linearity makes hard bop and trumpet sounds pleasant. The sense of volume in the mid to low range is also attractive not found in modern speakers. The exterior has been beautifully finished due to maintenance (Mizusaki Ryo)
Maintenance information: 2024.5.11 maintained (exterior repair/polishing/oil finish, front and rear baffle/horn repair/painting, saran net replacement/frame repair, woofer edge replacement, driver maintenance: magnetic circuit rust removal/gap cleaning/center adjustment, network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/screw replacement, unit detachment)
Accessories: saran net
Main specifications: 2-way bass reflex, 30cm woofer, frequency band, 40Hz to 16kHz, impedance, 8Ω, sound pressure level, 91 dB, dimensions W406 x H635 x D311 mm, weight 26 kg/book
The price has been reduced! 2024/5/19 sales price 218,000 yen As a successor to the T-1000, this FM stereo tuner digitized the main circuit part. The T-1000, which became a hot topic due to its astonishing high SN, has been further upgraded. The realistic sense of realism is unrivaled. The station button can store 10 stations. The exterior is good with no noticeable scratches. Serial J6Y807 (Yonejima Satoshi)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: remote control, instruction manual, power cord
Main specifications: frequency characteristics 10 to 15,000 Hz output/unbalance (RCA) 1 system balanced (XLR) 1 system digital output/coaxial 1 W465 x H150 x D393 mm 13.6 kg
The disposal price has been reduced (member prices are not applicable). 2024/5/15 sales price 398,000 yen Maintained! Kelly's SACD player. The high-class exterior is impressive with its sturdy aluminum housing and large spike equipment. The sound it creates is also bright and precise. In particular, when the CD software is upconverted to 96 kHz or 192 kHz, you can enjoy precise sound with a unique lightness. There are small wounds, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (The servo mechanism Assy has been replaced. The uneven parts of the top plate have been corrected as much as possible. The CD mechanism is removed from the chassis, the tray drive part is repaired, the grease on each part is removed due to dust adhesion, and Gushi-Mochi is re-coated. The damaged tray suppression mechanism has been repaired.
The cable has been fixed because the wiring styling is sandwiched between the shield case.)
Accessories: instruction manual, power cable, remote control
Key Specifications: SACD Player D/A Converter: Barbrown 1782u, 8 pieces parallel operation. Digital filter: using Pacific MicroSonic PMD200 W457xH127xD380mm 22.7kg
The disposal price has been reduced. Member discounts are not applicable. 2024/5/16 sales price 598,000 yen The version has been upgraded from DS/K1 to K3. A model equipped with KATALIST that has adopted a new clock architecture. Similar to the higher-level model KLIMAX DS/3, DSD can now also be played natively, and the range of playback has greatly expanded. It is a degree of perfection that is close to the height of the KLIMAX DS, such as improvements in power supply to the DAC and processor sections by examining the circuit layout. There is a line scratch on the display (Murakoshi Yoichi)
Maintenance information: 2024.5.15 sound output confirmed
Accessories: instruction manual, original box
Main specifications: Playback formats: DSF, DFF, FLAC, WAV, ALAC, AIFF, AAC, MP3, WMA, VORBIS (same as DS and other models) Compatible resolution: 7.35-192 kHz, 16-24 bit (similar to DS and other models) DSD64 (2.8224 MHz) /DSD128 (5.6448 MHz) compatible analog audio output: XLR balanced, RCA unbalanced (fixed/variable output) Digital audio output: 75Ω, BNC, 1 line, EXAKT LINK2 system, W380 x D380 x H91 mm, 5.6 kg
The price has been drastically reduced. 2024/5/17 sales price 148,000 yen B&W middle class “tweeter on top” model from the new commercial series. You can enjoy high-response sounds and vivid and realistic spatial expressions. There is a large dent on one side and side, and there is a light feeling of use and dullness (Murakoshi Yoichi)
Maintenance information: 2024.5.16 sound output confirmed
Accessories: saran net, instruction manual
Main specifications: 8Ω 88dB 45Hz to 50kHz W200 × H403 × D301 mm weight 8.9 kg
The price has been reduced. 2024/5/19 sales price 578,000 yen Mount an SME Series V to a Michell Engineering belt drive analog player. First of all, I'm drawn to this visual! Even though it's progressive, the design feels somewhat calm. The mechanism uses a floating 3-point support suspension and high-precision ball bearings that enable pinpoint contact to prevent vibration. In terms of sound quality, the precision that comes from SeriesV's tracing skills are well combined with a stable sound field expression with a good sense of connection. In addition to white rust on the exterior and arms, you can also see a feeling of use such as dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.17 Operation confirmed (rotation is slightly faster)
Accessories: instruction manual, original box, SeriesV instruction manual, original box
Main specifications: SME SerirSV: tapered magnesium arm, dynamic balance type, effective length 233.2 mm, needle pressure range 0 to 3 g, gyrodec: belt drive, 33/45 rotation compatible, W535 x H185 x D410 mm, 15.5 kg
The price has been reduced. 2024/5/19 sales price 398,000 yen ※The spike holder is a non-genuine product. A premium CD player in WADIA's heyday. The transport part is equipped with a TEAC VRDS version CMK3 mechanism. The DAC section also boasts such quality that it was later made independent as WADIA 25. The biggest appeal is the sticky mid-low range, which is different from ESOTERIC's sound quality. It can also be used as a D/A converter. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: remote control, instruction manual, power cord, spike holder (external product), original box
Main specifications: Esoteric VRDS system, CMK3, D/A converter can be used, W432 x D408 x H155 mm, 20 kg
Maintained! An original C22, a famous machine admired by enthusiasts. The thick, soft, and strongly extruded tone is a pleasant tone that can only be experienced with an old McKinn. It has a rich tone centered around the middle range with a high concentration, and it sounds with plenty of realism. The exterior has a feeling of use such as dullness and small scratches. Serial 44A12 (Hiroki Aso)
Maintenance information: 2024.5.19 maintained (main volume A curve replaced with the original vacuum tube 12AX7 noise replacement oil capacitor 0.01 μF domestically manufactured in the USA) replacement block capacitor 40/20/20/1000 μF other defective and deterioration replacement electrolytic capacitor 1000 μF additional electrolytic capacitor 40 μF other deterioration replacement switching noise reduction measures 1/4 W additional resistance 1/2 W deterioration replacement short (Additional pin vacuum tube socket, RCA jack caulk repair, and other operation checked with AC 100 to 117 V)
Accessories: A copy of the English instruction manual
Main specifications: 117 V specification, 4 input systems, 2 phono systems, frequency characteristics, 20 Hz to 20 kHz (± 0.5 dB), signal-to-noise ratio, 85 dB (high level), 62.5 dB (low level), distortion ratio 0.2%, W406 x H138 x D330 mm, 7.3 kg
Maintenance has been completed, such as replacing capacitors and replacing deteriorated parts! It is a famous machine with a velvet transformer, and you can enjoy rich sound with stable operation. The fresh, glossy tone in the mid-high range has a different appeal from the MC275. The exterior has a feeling of use over time, such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.19 Maintained (volume curing improvement treatment for TWIN, 2W oil capacitor replaced with 0.01μF, 3W oil capacitor replaced with 0.5 μF, missing thermistor, replacement, 250μF, domestic CE replacement, block capacitor 100/30 μF defective replacement, oil capacitor 0.22 μF defective replacement electrolytic capacitor 20μF, etc. Deterioration replacement resistor 2W deterioration replacement Vacuum tube socket and RCA jack caulking repairs ※ Other operation checks have been performed (measured at 41 to 58 W with rated output AC 100 to 117 V, SP: 8 Ω) ※ The power transformer groans a little, but there is no problem with performance)
Accessories: A copy of the English instruction manual
Main specifications: 40W+40W 6L6GCPP vacuum tube 6L6GC × 4 12AX7 × 3 12AU7x2 12BH7 × 2 frequency characteristics 16 to 40,000 Hz dimensions W400 × D265 × H195 mm weight 25 kg
The shadows of sound, and the expressive power of motion and stillness are really real. The sound is delicate and clear in the high range, and the overall transparency is high. The amplifier and volume adjuster are integrated, and an “AAVA” type volume with no mechanical contact is used. Many advantages can be obtained, such as improving the signal-to-noise ratio, reducing distortion ratio, suppressing changes in frequency characteristics, and not causing left and right volume errors. The external condition is that there are fine scratches on the top plate and line scratches on the sides. Serial H7Y419 (Yamato Yuki)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: instruction manual, power cable, remote control connection cable
Main specifications: 7 input/unbalanced (RCA) systems (however, 2 input systems can be used with an OP board attached), 2 balanced (XLR) systems output/balance (XLR), 2 unbalanced (RCA) systems each W477 x H156 x D412 mm 21.6 kg
※The spikes are out of stock. A polymer composite material, which is an ideal damping material for the surface in contact with the speaker, is used to ensure isolation between the speaker and stand. Also, resonance is suppressed by making 1 of the 3 struts thicker and changing the resonance frequency. The exterior has a feeling of use such as dullness and small scratches (Hiroki Aso)
Accessories: none
Main specifications: top plate W200 x D280 x H15 mm bottom plate W260 x D320 x 4 mm height 625 mm 6.0 kg per unit (actual measurement)
Fidelity-Research headshell Lightweight and highly rigid. It is characterized by an enveloping shape with a thick aluminum press-processed body. There are dullness and small scratches on the exterior (Murakoshi Yoichi)
Maintenance information: 2024.5.19 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 10g
*Needle cover is missing. Elliptical type with built-in step-up transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior has small scratches, dullness, and a feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.5.17 sound output confirmed
Accessories: none
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
Maintained. The Lux tubular premium FM/AM tuner WZ-30 was developed with the aim of being the ultimate FM stereo tuner. With the warm and thick sound quality typical of a tube ball, you can enjoy broadcasting in a relaxed atmosphere. The circle of the manufacturer logo on the front is off (Oikawa Tetsuji)
Maintenance information: 2024.5.19 Maintained (2 STEREO/MONO switching relays unstable replacement, 1 μF defective and deterioration replacement, 3 FM sensitivity improvement measures → vacuum tube 6CW4 replacement 3 (using supplies) · Noise improvement measures → 2 additional 0.002 μF Mylar capacitors · FM and AM circuit IF/RF/MPX re-adjustment
(*Operation has also been checked with AC 100V)
Accessories: copy of instruction manual
Main specifications: tubular FM/AM tuner W470 x H175 x D275 mm 10 kg
RCA cable 1.0m pair oxygen-free copper OFC Ritz wire 2-core shield plug, standard AccuPhase line cable with gold plating. The sound is more gorgeous than the L-10. There are dullness and scratches around the plug, and abrasions on the sheath (Kojima Yosuke)
Accessories: none
RCA cable 1.0m pair oxygen-free copper OFC Ritz wire 2-core shield plug, standard AccuPhase line cable with gold plating. The sound is more gorgeous than the L-10. There are dullness and scratches around the plug, and abrasions on the sheath (Kojima Yosuke)
Accessories: none
Comes with a glass base An all-in-one model that uses waveguide speaker technology to achieve an immersive and powerful sound like you would experience in a concert hall. In addition to CDs and FM/AM radios, you can wirelessly play music stored on your smartphone or tablet such as an iPad. Using your home Wi-Fi network, you can enjoy internet radio from around the world with just one touch. Operation and installation are simple and easy. It is in good condition (Oikawa Tetsuji)
Maintenance information: 2024.5.19 Operation confirmed (CD playback, remote control OK)
Accessories: remote control, instruction manual, power cable, FM antenna, glass base
Main Specifications: Wireless LAN: IEEE 802.11b/g/n Network Playback Sound Format: MP3, WMA, AAC, FLAC, Apple Lossless External Dimensions W368xH142xD221mm Weight 4.5 kg