It's junk because it seems a little distorted in the sweep test. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: Slightly distorted in the 2026.2.3 sweep test
Accessories: none
Main specifications: 10cm full range 8Ω 94dB 140Hz to 16,000 Hz external dimensions W502 x H303 x D200mm 5.7 kg (actual measurement)
I was able to fast forward and rewind, but the rotation is weak and there is almost no rotation, but when I turn it by hand as an aid, it starts spinning. The sound output has not been checked. It seems that the VU meter lamp glows and dims irregularly during the inspection at the time of arrival. The exterior has dirt, stains, rust, and tape marks. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2026.2.1 Operation confirmation Fast forward and rewind were possible, but playback is weak and hardly rotates, but when turned by hand as an aid, it starts spinning. The sound output has not been checked.
Accessories: soft cover
Main specifications: W430 x H522 x D270 mm 24.6 kg (actual measurement)
The motor turned on, but since there is no belt, the turntable does not rotate. I will sell it as junk without checking anything else. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2025.5.20 Power on. The pulley rotates. Since there is no rubber belt, the turntable does not rotate
Accessories: dust cover
Main specifications: W483 x H175 x D380 mm 8.3 kg
The power doesn't turn on and the volume knob is stuck. There are stains, scratches, and stains on the exterior. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2026.1.28 Operation confirmation The power does not turn on and the volume knob is stuck.
Accessories: none
Main specifications: W430 × H109 × D290 mm 6.5 kg
The right channel didn't come out at the time of check, so it's sold as junk. Please use it as a parts remover. *Member prices are not applicable for junk items (Murakoshi Yoichi)
Maintenance information: 2026.1.25 confirmed (right channel does not appear. (It will be handed over as is for junk items)
Accessories: none
Main specifications: 6.5 g dead weight
According to the inspection at the time of arrival, it is junk because there is 1 kHz distortion on one side and cracks in the edge of the MID and woofer on one side. The nails on the saran net are damaged. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2026.1.18 1kHz distortion on one side, cracks on the edge of the MID and woofer on one side. The nails on the saran net are damaged.
Accessories: saran net
Main specifications: 3-way bass reflex 6Ω 93dB linear phase speaker system dimensions W480 x H845 x D410 mm weight 36 kg
I was able to confirm the sound output, but it is not stable when 33/45 rotations get faster or slower. The base of the record cleaner is attached with adhesive, and a sticker is attached to the dust cover. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2026.1.21 Operation confirmation The sound output was confirmed, but it is not stable as 33/45 rotations get faster or slower.
Accessories: none
Main specifications: W453 x H139 x D366 mm 9.4 kg
The disposal price has been reduced! 2025/3/5 sales price 5,000 yen, power on, rotation OK. There is no Rch sound. Auto play doesn't work. I will sell it as junk without checking anything else. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2025.3.4 Power on. Rotation OK NG that doesn't make an RCH sound. Auto play doesn't work Nothing else has been checked
Accessories: dust cover
Main specifications: quartz lock direct drive W430 x H130 x D375 mm 7.1 kg
The motor turned on, but since there is no belt, the turntable does not rotate. I will sell it as junk without checking anything else. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2025.8.9 The power will be turned on. The pulley rotates. Since there is no rubber belt, the turntable does not rotate
Accessories: dust cover
Main specifications: belt drive FG servo DC motor W425 x H135 x D348 mm 5 kg
The power is on, but the rotation is unstable. The arm can make a sound. I will sell it as junk without checking anything else. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2025.3.20 The power will be turned on. Rotational instability is not allowed. Arm sound can be made. Nothing else has been checked
Accessories: dust cover
Main Specifications: Direct Drive AC100V 50Hz/60Hz W430 × H125 × D346mm 6.1 kg
The power turns on, but the rotation is a bit slow. Checking the sound on the arm is OK (the cartridge is out of stock). The dust cover hinge is missing. I will sell it as junk without checking anything else. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2025.3.24 The power will be turned on. The rotation is a little slow. Check the sound output of the arm OK (cartridge is missing) and others have not been checked
Accessories: power cord, dust cover
Main specifications: W428 x H116 x D375 mm Weight 4.7 kg
The disposal price has been reduced! 2025/2/5 sales price 4,000 yen power will be turned on. Rotational instability is not allowed. Since there are no turntable center shaft parts, the board cannot be set. I will sell it as junk without checking anything else. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2025.2.4 Turn on the power. Rotational instability is not allowed. Since there are no turntable center shaft parts, the board cannot be set. Nothing else checked
Accessories: dust cover
Main specifications: W452 x H170 x D360 mm 8.95 kg
1 bottle only. I was able to confirm the sound output, but there is slight distortion around 1 khz. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2026.1.10 Operation confirmation 1 unit only. I was able to confirm the sound output, but there is slight distortion around 1 khz.
Accessories: none
Main specifications: W283 x H133 x D252 mm 1.82 kg (actual measurement)
The sound output was confirmed, but there was a gap in the volume and the sound was interrupted. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2026.1.10 Operation confirmation The sound output was confirmed, but there is a gap in the volume and sound interruptions occur.
Accessories: none
Main specifications: W430 x H86 x D254 mm 4.6 kg
I turned the turntable with the power turned on, but the arm operation and sound output were unchecked. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (TAKIMOTO Yutaka)
Maintenance information: 2026.1.2 Operation confirmation The turntable turned on, but the arm operation and sound output have not been checked.
Accessories: power cord
Main specifications: W315 × H88 × D315 mm 4.1 kg
The stylus chip is still there, but the sound output has not been confirmed. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.31 Operation confirmation Unchecked.
Accessories: none
The power was applied, but the tuning memory is disconnected and tuning is not possible. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.27 Operation confirmation The power was applied, but the tuning memory is disconnected and tuning is not possible.
Accessories: loop antenna
Main specifications: W430 x H53 x D300 mm 3.3 kg
The sound output was confirmed, but there was slight distortion in the high frequency due to the sweep. The cone paper is discolored and there is a dent in the center cap. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.26 Operation confirmation The sound output was confirmed, but there was slight distortion in the high frequency range during the sweep.
Accessories: manual
Main specifications: W121 x H104 x D121 mm 0.78 Kg/1 bottle
The power supply was confirmed, but the operation has not been checked. The lamp on the VU meter is out. There is dirt, stains, and rust on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.26 Operation confirmation The energization was confirmed, but the operation has not been checked. The lamp on the VU meter is out.
Accessories: none
Main specifications: W420 x H344 x D190 mm 11.26 kg (actual measurement)
AM/FM was received, but there is a gap in the FM frequency display. Other details have not been checked. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.26 Operation confirmation AM/FM was received, but there is a gap in the FM frequency display. Other details have not been checked.
Accessories: none
Main specifications: W430 × H53 × D300 mm 3.2 kg
Since there is no needle, the sound cannot be confirmed. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.26 operation confirmation
Accessories: none
Main specifications: dead weight 5.6 g
In the check at the time of arrival, it was possible to rotate 33/45 and there was a sound, but it seems that the record was not traced. The cartridge's mounting screw is crushed. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.25 Operation confirmation In the inspection at the time of arrival, 33/45 rotations were possible and a sound was made, but the record was not traced.
Accessories: none
Main specifications: W430 x H88 x D350 mm 7.0 kg
The sweep test is OK, but it's junk because there is a dent in the center cap of the MID on one side. There is a chip on the saran net frame. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (TERAMOTO Yoshihiko)
Maintenance information: 2025.12.20 sweep test ok. There is a dent in the center cap of the MID on one side. There is a chip on the saran net frame
Accessories: saran net
Main specifications: W365 x H804 x D305 mm weight 12.25 kg
AM/FM was received, but the sensitivity was low, and there was a gap in the OUTPUT LEVEL, so the sound on one side was not produced. The exterior has stains, stains, rust, and decay. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.16 Operation confirmation AM/FM was received, but the sensitivity was low and there was a gap in the OUTPUT LEVEL, and the sound on one side was not produced.
Accessories: none
Main specifications: W410 × H140 × D360 mm 7.4 Kg
Since the cantilever is broken at the root, it has not been possible to confirm the sound. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.16 Operation confirmation Unchecked.
Accessories: none
Main specifications: dead weight 6g
Since the cantilever is broken, the sound cannot be confirmed. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.14 Operation confirmation Unchecked.
Accessories: none
Main specifications: dead weight 5.6 g
AM/FM has been received, but the display is not displayed. The exterior has stains and stains. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.14 Operation confirmation AM/FM has been received, but the display is not displayed.
Accessories: none
Main specifications: W430 × H64 × D241 mm 2.8 kg
I was able to confirm the sound output, but both are distorted. Something like an adhesive is attached to it. The exterior has stains, stains, rust, and stickiness. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.14 Operation confirmation The sound output was confirmed, but both are distorted.
Accessories: none
Main specifications: 5 cm caliber horn type playback frequency 3,000 to 25,000 Hz W70 x H70 x D60 mm 0.35 kg/1
The sweep test had slight distortion in the mid to high range. The center cap is crushed, the edges are sticky, and the corn paper is yellowed. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.13 Operation confirmation The sweep test was completed, but the center cap is crushed, the edges are sticky, and the corn paper is yellowed.
Accessories: manual
Main specifications: W121 x H104 x D121 mm 0.78 Kg/1 bottle
The stylus chip is still there, but the sound output has not been confirmed. There are stains, scratches, and stains on the exterior. Please use it as a parts remover. *Member prices are not applicable for junk items. (SUZUKI Keita)
Maintenance information: 2025.12.13 Operation confirmation Unchecked.
Accessories: none
Main specifications: needle pressure 1.75 g, dead weight approx. 15 g