Maintained! The crossover has a 2-way specification of 800 Hz. A 2-way/3-way channel divider that allows you to change crossovers by replacing boards. Attenuation characteristics are possible by switching between -12 dB and -18 dB/oct (Daiki Goto)
Maintenance information: 2024.9.13 Maintained (1) Since RCH was -18 dB/OCT compared to LCH -12 dB/OCT, the low path blocking characteristics were reset to -12 dB/OCT as well as LR. 2) Each volume contact disassembly and cleaning procedure, bonnet mounting screw replacement 4) insertion loss 0 dB crossover frequency 800 Hz (-3 dB) Low, and 2-way operation with MID output was confirmed. Since it is a 2-way operation, there is no high output. 5) Other cutoff frequency slope switching SW and SUB WOOWER output switching SW disassembly cleaning, door catch magnet adhesion treatment. 6) Part of the heat-deformed audio electrolytic capacitor was replaced with an equivalent audio capacitor, and the energizing operation sound output test is good.)
Accessories: power cable, manual
Main specifications: 180 Hz/3,500 Hz 3 way specification frequency characteristics (single channel equivalent band) 20 Hz to 20 kHz slope characteristics -12 dB/oct, -18 dB/oct, -24 dB/oct switch switching type W445 x H109 x D373 mm 9.1 kg
Maintained! The crossover has a 500Hz 2-way specification. A 2-way/3-way channel divider that allows you to change crossovers by replacing boards. Attenuation characteristics are possible by switching between -12 dB and -18 dB/oct (Daiki Goto)
Maintenance information: 2024.9.13 Maintained (volume and crossover slope switching SW contact disassembly cleaning. 2) Due to buffer amplifier operation misalignment, replace the bias LED x 2. 3) Insertion loss LOW OUT 1.3 dB (Lch Rch) MID OUT 1.0 dB (Lch Rch) 4) The crossover frequency 500 Hz (-3 dB) was confirmed, and operation is good at a slope of 12 dB/OCT. The slope can be switched between 12 dB/oct and 18 dB/oct, and this unit is set to 12 dB/oct.)
Accessories: power cable
Main specifications: 180 Hz/3,500 Hz 3 way specification frequency characteristics (single channel equivalent band) 20 Hz to 20 kHz slope characteristics -12 dB/oct, -18 dB/oct, -24 dB/oct switch switching type W445 x H109 x D373 mm 9.1 kg
5 tier rack with glass doors by Denon The shelf can be changed depending on the dowel position. As for the exterior, part of the shelf board is glued together. Other than that, there are scratches, scratches, and dullness overall (Mizusaki Ryo)
Accessories: caster stop
Main specifications: outer dimensions W580 x H1010 x D470 mm inner dimensions W533 x H866 x D450 mm 36 kg
The MC-L1000 is now in stock, the highest peak MC cartridge with the super direct couple system that Victor Japan is proud of. This revolutionary cartridge is directly connected to the stylus and coil. The body is luxuriously machined with duralumin and is reliable enough. Its sound quality, which has a wide range and is overwhelmingly high in transparency, is the pinnacle of domestically produced MC cartridges. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.9.14 sweep test is good
Accessories: needle cover
Main specifications: Super direct couple system MC type special microridge needle output voltage 0.22 mV 30 ohms frequency characteristics 10 Hz to 50,000 Hz suitable needle pressure 1.35 to 1.65 g dead weight 10.5 g
Unspecified set of 2 granite boards It is a high-weight board with a beveled surface and a mirror finish applied only to the surface, which contributes to damping vibrations and tightening the sound. The exterior is dull and scratched. (FUJISAWA KOSHI)
Accessories: No accessories
Main specifications: W400×H10×D400mm
Unspecified set of 2 granite boards It is a high-weight board with a beveled surface and a mirror finish applied only to the surface, which contributes to damping vibrations and tightening the sound. The exterior is dull and scratched. (FUJISAWA KOSHI)
Accessories: No accessories
Main specifications: W400×H10×D400mm
6 month warranty. Audio Alchemy D/A converter. The thick, dark sound is attractive. Sounds that fly forward seem to be compatible when incorporated into vintage systems. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.9.13 Operation confirmed
Accessories: power cable
Main specifications: 1 bit sigma delta input/BNC (RCA) ×3/optical ×1 W407 × H65 × D206mm 1.9 kg
RCA cable, 1.0 m, uses a pair of mu conductors, has a hyper-balanced structure with ground, and the tone is not tight, but it is attractive that the low frequencies don't slack off. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.9/11 continuity confirmed
Accessories: none
A 1.5m pair of XLR cables uses the same cable as the internal wiring of the SOULNOTE amplifier. XLR unshielded to transmit audio signals with high purity. You can enjoy a clear sound (Satoshi Yonejima)
Maintenance information: 2024.9/11 continuity confirmed
Accessories: original box
Maintenance has been completed, including replacement of 11 deteriorated electrolytic capacitors! The Aurex brand's first separate control amplifier. The power supply unit is an L/R separate type, a model with a simple ceiling panel design, etc., where you can feel the attention to detail. I am impressed by the pure sound without any habit. There are multiple line scratches on the top plate (Sasaki Shota)
Maintenance information: 2024.8.31 Maintained (replaced due to power circuit resistance disconnection. The PHONO circuit film capacitor was replaced due to a short circuit. The other electrolytic capacitors have been replaced. Contact cleaning grease was applied to the INPUT switch, TAPE switch, TONE, filter switch, etc. for poor contact disassembly contacts. Volume contacts have been cleaned. Each input/output operation was checked)
Accessories: none
Main specifications: 2 PHONO inputs Phono 1:2.0 mV/47 kΩ/Phono 2:2.0 mV/47 kΩ, 100 kΩ Frequency characteristics: 10 Hz to 100000 Hz External dimensions W450 x H93 x D379 mm Weight 9.5 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/8/17 sales price 118,000 yen Equipped with a JET V tweeter that is also used on the 300/400LINE higher-end machines. The round cabinet and network have been revamped, so you can enjoy an even more refined and clear ELAC sound. As for the exterior, there are curls at the top of the saran net on both the left and right. Serial 31770E0000803/31770E000804 (Yonejima Satoshi)
Maintenance information: 2024.8.17 sweep test good
Accessories: saran net
Main specifications: 2-way bass reflex efficiency 87 dB impedance 4 ohms frequency characteristics 41 to 50,000 Hz crossover frequency 2,500 Hz maximum input 80 W 192 x H285 x D 285 mm weight 6.6 kg
※Acrylic boards are cheap because they are warped. An audio board that uses strong magnetic energy to achieve ideal floating. The effect of floating is outstanding! It's an item that can further bring out the appeal of your record player or CD player. There is a feeling of use on the exterior of the acrylic board, such as warping, scratches, and the magnet printing disappearing (Daiki Goto)
Accessories: none
Main specifications: maximum load: 25 kg W512 x H70 x D392 mm 3.6 kg (actual measurement)
Power cable, 1.1 m, terminal, unprocessed OFC conductor. A masterpiece of S/A Lab that was a big hit because it can be used as both a speaker cable and a power cable. The thick, tight low frequency of the extruded sound image is attractive. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.8.23 continuity confirmed
Accessories: none
The price has been reduced. 2024/9/7 sales price 4,500 yen. Sold out power cable, 0.75m, untreated end, 3-core structure, highly transparent, and features crisp sound quality over a wide band (Murakoshi Yoichi)
Maintenance information: 2024.9.6 continuity confirmed
Accessories: none
The price has been reduced! 2024/9/10 sales price 12,000 yen*Currently sold. Mercury F1 after the company. Equipped with a soft dome tweeter using neodymium magnets, uniform high-frequency radiation characteristics are achieved. You can enjoy a clear tone without turbidity. As for the exterior, the TW surface has deteriorated. Serial 813849, 813850 (Fujisawa Yukishi)
Maintenance Information: 2024.9.10 Operation confirmed
Accessories: saran net
Main specifications: 87dB W170 × H300 × D220 mm 4.4 kg
The disposal price has been reduced! (Member price not applicable) 2024/9/2 sales price 25,000 yen High-resolution USB-DAC/ADC capable of DSD recording with a professional-quality AD converter and archiving analog records using phono input. It is a USB/DAC that supports 5.6 MHz and 2.8 MHz for DSD and up to 192 kHz/24 bit for PCM for both recording/playback, and can DSD record handheld sources. The exterior is good with no conspicuous scratches. Serial 006146 (Fujisawa Yukishi)
Maintenance information: 2024.9.2 operation confirmed
Accessories: instruction manual, USB cable, original box
Main specifications: number of channels · 2 channel input format (USB) DSD · 2.8224 MHz/5.6448 MHz, 1 bit, PCM · 44.1 kHz/48 kHz/88.2 kHz/96 kHz/176.4 kHz/192 kHz, 16 bits/24 bit W155 ✕ H49 ✕ D184 mm 1.1 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/8/31 sales price 64,800 yen This is a highly cost-effective speaker that is small yet allows you to hear a sense of scale that doesn't make you feel the size. Using a dome tweeter, the high-frequency range with a high texture that is easy to listen to is attractive. The exterior has dullness and line scratches. Serial 011220/011221 (Tamura Eiji)
Maintenance information: 2024.8.31 Maintained (replacement of 8 speaker terminals and tightening of screws between terminals and board connections. Sound output check is normal)
Accessories: saran net, jumper cable (substitute)
Main specifications: 2 way 2 speakers, bass reflex type, anti-magnetic specification, 130 mm carbon woofer x 1, 25 mm soft dome tweeter x 1, frequency characteristics, 45 Hz to 30 kHz output sound pressure level, 90 dB impedance, 4 ohms, size W145 x H335 x D350 mm, weight 8.5 kg
Krypton high carbon steel insulator set of 8 It is a product that greatly improves acoustical and physical properties such as sound propagation speed with a special hard coating. It uses silicone rubber material that dampens the natural vibrations of the metal and has an anti-slip effect with the floor, and has an adhesive effect on the floor. There are dullness and scratches (Daiki Goto)
Accessories: none
The disposal price has been reduced (member prices are not applicable). 2024/9/7 sales price 268,000 yen Maintenance completed! LUXMAN 70th anniversary signature model. The standard EL34 push-pull configuration has an OY transformer, and is designed so that you can fully enjoy the flavor of luxe stone. Using an unprecedented high-rigidity chassis, it also has an outstanding sense of luxury. This is a 90s vacuum tube premain with a good balance of range width, thickness, and tone. There is a scuff on the front knob (Kojima Yosuke)
Maintenance information: 2024.1.13 maintained (rotary switch replacement, 2 output tubes replaced due to right channel bias, double channel drive stage socket replacement, switch contact disassembly, cleaning volume, cleaning knob, milling correction, vacuum tube pin cleaning bias adjustment, output voice check, sound check at 8 Ω load)
Accessories: copy of instruction manual, power cable
Main specifications: output 30W+30W (6Ω) phono (mm) 2.5mV/47kΩ vacuum tube EL34 (6CA7) x 4, 12AU7 x 4, 12BH7A x 2 W430 x H209 x D387 mm weight 22 kg
The price has been drastically reduced. 2024/9/11 sales price 198,000 yen Maintained! ※The lamp is out, but it cannot be replaced, and the letters light up. The initial NAP250 has arrived. The compact yet rich, bold tone is attractive. Combining it with an English manufacturer is better, but in combination with an Italian manufacturer such as Sonas, it makes a sound that floats up in space. Please enjoy a stylish and intelligent sound that is slightly different from American products (Daiki Goto)
Maintenance information: 2024.9.11 Maintained (LED is out of date → cannot be obtained or replaced because it is an integrated LED in the shape of a sheet, and the LED itself is broken on the leftmost logo part, so the letters light up. Shock noise → install a timer relay because there is no mute circuit (the sound comes out 5 seconds after turning on the power), large hum → the capacitor in the board runs out of capacity → replace it.)
Accessories: manual, power cable, connection cable
Main specifications: 70W+70W output 70W+70W/8Ω W430 × H85 × D300 mm weight 11.9 kg (actual measurement)
The price has been drastically reduced. 2024/9/11 sales price 178,000 yen Maintained! A heavyweight power amplifier that is a sibling of the company's B-2301. A considerable amount of material was put in at the time, and it is a luxurious gem. The rugged design has an appealing bass that sits at the back, and goes well with jazz, rock, etc. There are small scratches and paint peeling in places (Oikawa Tetsuji)
Maintenance information: 2024.9.11 Maintained (protection is applied due to deterioration of the constant current diode on the flat amplifier board. Constant current diode replacement in power amplifier boards and flat amplifier boards. Power amplifier board zener diode, semi-fixed volume deterioration replacement. Meter lamp replacement. Speaker relay poor contact replacement. Input LEVEL switch disassembly contact polishing. (General adjustment)
Accessories: instruction manual
Main specifications: 200W+200W input level left and right independent step method S/N120dB dimensions W474xH215xD505mm weight 35 kg
The price has been drastically reduced. 2024/9/11 sales price 378,000 yen Maintained! Genuine Electri This is a replica of the famous C22 from yesteryear. In addition to the luster and thickness of the tone comparable to the original, the high level of SNR compatible with current sources is attractive. The stunning art deco design with black glass panels and silver hairlines is also excellent. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2024.9.11 maintained (output panel lamp out → replacement, high filter distortion large (Rch) → tube replacement, SW, VOL cleaning, contact plate cleaning, RCA pin jack cleaning, re-soldering, tube cover, rubber bush deterioration replacement, operation check, cleaning)
Accessories: Copy of instruction manual (English)
Main specifications: 3 line inputs, 2 phono/tape inputs, 2 systems each with balanced output, use vacuum tubes 12AX7 x 4, 12AT7 x 3 dimensions W406 x H138 x D330 mm, weight 7.3 kg
The capacitors, switches, and volume were thoroughly maintained in 2024/7! Lux's early transistor pre-main amplifier. The vocals stand out based on a faint warm sound, and you can feel the thickness of the mid-range. It has an appeal not found in current models. The exterior has line damage, dullness, etc. (Oikawa Tetsuji)
Maintenance Information: 2024.7.4 Maintained (main volume, Treble/Bass, balance volume cleaning cleaning. Rotary switch contact cleaning for source, stereo mode, etc. Contact cleaning for all toggle switches, such as Att/Normal. The capacitance and ESR values of the electrolytic capacitors in the board were inspected, and 26 deteriorated electrolytic capacitors were replaced. Pre/Main slide switch contact cleaning. Pilot lamp preventive replacement. Clean the front panel and knobs and clean the interior and RCA terminals. Offset, idle adjustment)
Accessories: power cable
Main specifications: 30W+30W (8Ω) W451 × H148 × D268 mm 10.5 kg
The price has been drastically reduced. 2024/9/10 sales price 168,000 yen Gastard's high-performance network music streamer. The chip uses Asahi Kasei high quality chip AK4499EX. The PCM768, DSD512, and MQA are compatible up to 384K. Compatible with Roon, Upnp, and Hqplayer NAA (Murakoshi Yoichi)
Maintenance information: 2024.9.8 sound output confirmed
Accessories: remote control power cable, USB cable, replacement fuse, original box
Main specifications: IIS, USB, LAN: DSD64-DSD512 PCM 44.1K-768K, MQA 8X coaxial, AES, optical DSD64, PCM 44.1K-192K, MQA 8X LAN: Roon, Upnp, HQPlayer NAA output RCA, XLR 1 system each W330 x H65 x D260 mm weight 5.6 kg
The price has been drastically reduced. 2024/8/26 sales price 79,800 yen 607 S2 anniversary edition with power and a sense of scale. A decoupling double dome tweeter with a proven track record is used to achieve 38 kHz high frequency limit characteristics. You can enjoy accurate and clear sound typical of the company. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.8.26 Operation confirmed
Accessories: instruction manual, original box, saran net, bass reflex sponge, rubber feet, jumper plate
Main specifications: 2 way 8Ω 84dB W165 × H300 × D207 mm 4.7 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/7/28 sales price 59,800 yen Maintained! The large fan is worrisome, but the quiet rotation and the design that suppresses the fan's sound as much as possible by tuning the fin-shaped wind noise is impressive. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.7.28 Maintenance completed (full replacement of electrolytic capacitors, board solder repair, sound output confirmation test. (The PEAK lamp does not light up, but there were no problems with the inspection of related parts, and since the operation specifications of the PEAK lamp are unknown, it is currently completed)
Accessories: none
Main specifications: 200W+200W (8Ω) damping factor 200 (at 100Hz) 60 (20-20kHz) W222 x H165 x D274 mm 10.2 kg
Marantz's luxury SACD/CD player that has undergone a full model change from the SA-11S2. The resolution is high, and it has a natural afterglow where transparency, subtlety, sound field, breathing, etc. can also be felt realistically (Daiki Goto)
Maintenance information: 2024.9.13 operation confirmed
Accessories: manual, power cable ※ remote control is being ordered
Main specifications: Playback frequency range 2 Hz to 100 kHz (SACD) 2 Hz to 20 kHz (CD) output terminal/RCA x 1, XLR x 1 (analog) coaxial x 1, optical digital x 1 (digital) headphone x 1, digital input terminal/coaxial x 1, optical x 1, USB-A (front) x 1, USB-B (rear) x 1, W440 x H127 x D417 mm 16.5 kg
An audio board that makes full use of the sounds of natural materials. High-density lumbar core plywood using rubber wood as the base is used. Moabi (Nanyo cherry) wood is used as the surface material used in high-grade furniture. It's an item that pushes the resolution, good localization, and sense of volume in the low frequencies one level up. There is a scratch (Daiki Goto)
Accessories: none
Main specifications: load capacity is 100 kg W450 x H30 x D400 mm 4 kg
Rare amplifiers are in stock. A preamp that has the transparency and subtlety of a high-end while maintaining a KREL-like sense of temperature. Built-in high sound quality head amplifier compatible with MC/MM. The gain is so high that there is a slight sound leak even when the volume is turned off (Sasaki Shota)
Maintenance information: 2024.9.13 Maintained (input selector, tape switching, balance, contact cleaning due to poor contact with each rotary switch, readjusted the bias and DC offset of each amplifier, replaced terminals due to damage to the plastic part of the ground terminal, and inspecting each operation.)
Accessories: connection cable
Main specifications: [main body] W483 x H63 x D340 mm 8.2 kg [power supply part] W483 x H63 x D305 mm 9.3 kg [transformer] W95 x H60 x D335 mm 4.2 kg
The TAOC Sycamore Sound Creation Board is now in stock. How about it under the feet of tall boy speakers with spikes, which are common these days, and I recommend it to those who want to keep the bass sharp. Scratches are conspicuous (Daiki Goto)
Accessories: none
Main specifications: melamine veneer, cast iron powder, high-density wood board x 2, 5-layer structure of phenolic laminated board, external dimensions W350 x D450 x H40 mm, weight 5.0 kg
Manufacturer's maintenance completed! This model has eliminated unnecessary auxiliary functions and has been thoroughly particular about sound quality. You can enjoy the delicate sound that pursues linearity unique to pure A class. This model has expressive power that you wouldn't think of as a pre-main amp, and is still popular today. There are scuffs on the exterior and sides (Murakoshi Yoichi)
Maintenance information: 2024.9.12 manufacturer maintenance (speaker terminal replacement, output relay replacement, board solder correction, volume, switch contact cleaning, internal cleaning, general adjustment)
Accessories: copy of the manual
Main specifications: pure A grade operation 50W+50W (8Ω) line input 8 systems (RCA x 7/XLR x 1) 2 phono systems (MM/MC) W438 x H176 x D467 mm 30 kg
※There is a smell in the room. RCA cable, 1.0 m pair, 6N copper conductor, and a luxurious specification using 6N material for the shield. It is a cable with resolution and natural sound quality perfect for high-resolution playback (Yoichi Murakoshi)
Maintenance information: 2024.9/11 continuity confirmed
Accessories: case, instruction manual
※There is a smell in the room. The 1.5m stress-free 6N conductor terminal RCA digital cable was originally intended for video, but it also has a powerful, sharp sound for audio applications. There is a slight sunburn on the shield (Murakoshi Yoichi)
Maintenance information: 2024.9/11 continuity confirmed
Accessories: case, instruction manual
LUXMAN's classic speaker selector. This is a convenient item that can be switched with a single switch for those with multiple speakers or when listening to and comparing differences in sound. The exterior is dull enough for the model year (Hiura Katsuji)
Maintenance information: 2024.9.13 continuity confirmed
Accessories: none
Main specifications: 4 systems switchable W141 x H58 x D59 mm 760 g
*Since it is an AIR BOW tuning specification, it will be sold as is. An AIRBOW tuning product for the Marantz PM6006. By applying the mechanism of the resonant part of the instrument to the electrical circuit, CD players and amplifiers are designed so that they can produce richer sounds. There are a few scratches, but it can be said that it is generally good. Serial AFC12170902780 (Fujisawa Yukishi)
Maintenance information: 2024.9.13 operation confirmed
Accessories: remote control, power cord, instruction manual
Main specifications: 40W x 2 (8Ω) 55W x 2 (4Ω) analog input/Phono x 1 (MM), LINE x 4 analog output/LINE x 1 (REC-OUT) digital input/coaxial (RCA) x 1, optical (TOS) x 2 headphone output/standard stereo jack x 1 W440 x D370 x H105 mm weight 7.8 kg
Genuine Rin Japan. The rare MAJIK-I is in stock. A Puirimain amplifier equipped with a specially designed preamp and phono module in a highly rated CHAKRA power amplifier. The sound, which combines subtlety and driving power, is truly magical. There are no noticeable scratches on the exterior. Serial 1168440 (Fujisawa Yukishi)
Maintenance information: 2024.9.13 operation confirmed
Accessories: remote control, power cord
Main specifications: integrated amplifier playback frequency/PRE AMP 2.5 Hz to 170 kHz/power amp 2.5 Hz to 48 kHz input impedance/LINE 10 kΩ/AUX 100 kΩ/mm48 kΩ PHONO STAGE GAIN W381 × D355 × H80 mm weight 4.9 kg
*Set of 2 TAOC audio board Five-layer structure of melamine veneer, cast iron powder, high density wood board, and phenolic laminated board. Of course, it's just the right size for a tall boy type speaker, or for placing it under an amplifier or CD player. Bits and peeling wounds can be seen. Also, felt is attached to the bottom (Fujisawa Yukishi)
Accessories: No accessories
Main specifications: W450 x H40 x D450 mm 6.5 kg
Quadra Spire's classic Q4D series suri glass 4-tier rack. It has a cooler impression, probably because of the difference in material compared to normal Q4 etc. It is a 19mm diameter silver pole with spikes. The space between the shelves is 140 mm. (FUJISAWA KOSHI)
Accessories: No accessories ※Spike received, missing
Main specifications: plate thickness 10 mm, load up to 70 kg per shelf W588 x H535 x D393 mm (actual measurement)
Popular model of MC step-up transformer. In addition to switching the primary impedance of 3, 6, 12, 24, and 48 ohms, it can be bypassed, making it extremely easy to use. The sound is rich and powerful, and it is a trance known for its high ability. (FUJISAWA KOSHI)
Maintenance information: 2024.9.13 operation confirmed
Accessories: No accessories
Main specifications: boost ratio 3 ohm · 32 dB, 6 ohm · 29 dB, 12 ohm · 26 dB, 24 ohm · 23 dB, 48 ohm · 20 dB playback frequency band 4 Hz to 120 kHz W80 × H40 × D150 mm 761 g
This is the MC cartridge GMC-10E from Grants. It has an unobtrusive sound and is perfect as an introduction to MC cartridges. You can enjoy delicate and highly transparent sound quality (Hiura Katsuji)
Maintenance information: 2024.9.10 sound output confirmed
Accessories: none
Main specifications: 0.3 mV needle pressure 2 g dead weight 4.8 g
RCA cable uses a 1.5m pair mu conductor, hyperbalanced structure with ground, and the tone is not tight, but it is attractive that the low frequencies don't slack off (Murakoshi Yoichi)
Maintenance information: 2024.9/11 continuity confirmed
Accessories: none
Speaker cable 2.2 m pair terminal unprocessed. High purity 7nCu/6NCu hybrid multi-conductor cable. We have achieved unrivaled cost performance. All materials and configurations, such as insulators, coatings, and inclusions, are the same as 7N and 7.8N cables, and it is an ultra-high purity cable with almost no loss due to impurities (Hiura Katsuji)
Maintenance information: 2024.9/11 continuity confirmed
Accessories: none
※It is currently sold because it is cheap. DALI small speakers. It features a small yet powerful low range and a glossy mid to high range. It's a sound with good visibility, and you can feel the spread of the sound (Daiki Goto)
Maintenance information: 2024.9.13 Operation confirmed.
Accessories: none
Main specifications: 2 way bass reflex type 6 ohm 84.5 dB recommended amplifier output 25 to 100 W frequency characteristics 54 Hz to 26 kHz W170 x D238 x H292 mm 4.2 kg
※The Rch is slightly longer, and there is a part where the inside of the plug connection is exposed, so it is inexpensive. RCA cable, 1.0 m, uses a pair of mu conductors, has a hyperbalanced structure with ground, and the tone is not tight, but it is attractive that the low frequencies don't get slack (Murakoshi Yoichi)
Maintenance information: 2024.9/11 continuity confirmed
Accessories: none
The disposal price has been reduced. Member discounts are not applicable. 2024/6/21 sales price 218,000 yen Maintained! A regular Yamagiwa model. It is a hidden popular model as the successor to the C26. It is an amplifier from the golden age of McKinn that is highly popular with music fans, with a sound reminiscent of a rich, thick vacuum tube sound. It makes vintage speakers sound intense. The exterior has paint floats, rust spots, etc. Serial BV1675 (Murakoshi Yoichi)
Maintenance information: 2024.6.21 maintained (each SW, VOL cleaning, lamp deterioration replacement, pin jack cleaning, earth plating wire treatment, poor push button SW contact → dismantling cleaning, operation check (gaps cannot be completely removed))
2022.2.4 Maintained (replaced due to poor noise compared to power circuit transistors. Electrolytic capacitor replacement. Selector switch contact cleaning contact grease application. Replace a dead lamp. Replaced because the RCA terminal plating has peeled off and deteriorated. (Each input/output operation test)
Accessories: instruction manual (copy)
Main specifications: input PHONO 1 · 2, AUX 1 · 2, TUNER, TAPE 1 · 2 W435 × H188 × D395 mm 11.8 kg
The A3500 vacuum tube power amplifier has been refreshed by thorough maintenance down to the smallest details, such as volume disassembly and polishing. The warm, fresh tone, filled with the appeal of a vacuum tube type, is still appealing enough today. You can enjoy music with a rich, thick tone that contrasts with the clicking tones of recent vacuum tube amplifiers. As for the exterior, paint deterioration and peeling can be seen on the transformer on one side, and there is a feeling of use such as dullness, small scratches, etc., and there is a dent in the hood. ※3-pole tube connection specification. 20W+20W (actual measurement) is output as specified by the manufacturer (Takasaki Atsushi)
Maintenance information: 2023.2.3 maintained (main tube (6CA7) replacement vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, complete disassembly of semi-fixed VR replacement power input gain volume, contact polishing, anti-oxidation/sulfation grease coating load test (8Ω load 1kHz 20W+20W) input/output waveform confirmation sound output check performed)
Accessories: copy of the manual
Main specifications: 20W+20W (8Ω) vacuum tube 6CA7×4/6AQ8×3 W465×H168×D206mm 16kg
The price has been reduced. 2024/9/11 sales price 19,800 yen. ※Both sides are heavily sunburned on the left side, so they are inexpensive. Woofer edge softened A compact 3-way speaker that is one size smaller than the DS-77Z. Characters with high resolution and clear outlines, which are advantages of Japanese speakers. The clear and bright sound is suitable for popular systems in general. In addition to the exterior, as described above, you can see a feeling of use such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.9.11 maintenance (edge softening treatment)
Accessories: instruction manual, saran net
Main specifications: 3-way 3-speaker rear bass reflex 6Ω 90dB size W330 x H580 x D320 mm weight 17 kg
The price has been reduced. 2024/9/12 sales price 5,000 yen. It is inexpensive because it has strong rust. Set of 8 brass (brass) spike holders They are familiar with their natural, thick, brass-like characters. The exterior has dirt, scratches, and dullness (Hiura Katsuji)
Accessories: none
Main specifications: diameter 40 mm x 8 mm 72.5 g
A Sony headshell with a unique design. The cartridge holder is in the shape of a slide bar, making it easy to adjust the overhang. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.9.3 continuity confirmed
Accessories: none
Main specifications: high rigidity die-cast aluminum, dead weight 11g