Full maintenance has been completed, such as replacing 54 deteriorated capacitors and disassembling all switches and cleaning contacts! Macintosh's classic preamp. It reproduces clear mid-range and glossy tones. This model should be used by music fans who enjoy all kinds of sources. The full range of functions, such as a 5-band equalizer and a 7-source input selector, is also attractive. It is a relatively beautiful individual for its age. Serial JEB8569 (Fujisawa Yukishi)
Maintenance information: 2026.4.11 Maintained (The contacts were cleaned due to poor contact with the rear RCA processor terminals. All rotary switches and push switches were dismantled, contacts cleaned, and contact grease applied. The menvolume disassembly contacts have been cleaned. The other volume contacts have been cleaned. 54 electrolytic capacitors have been replaced. The panel lamp was replaced because it turned black. Panel peeling has been fixed. The knobs are glued and fixed. There was a lot of dirt on the inside and outside, so I cleaned it. Each input/output operation was checked.)
Accessories: instruction manual
Main specifications: Equalizer up and down 12dB (center frequency/30Hz/150Hz/500Hz/1.5kHz/10kHz) rated output 20W+20W (8Ω) W445 x H192 x D395 mm 11.8 kg
Shure's classic needle pressure gauge. Needle pressure can be adjusted in 0.05g increments. Since there are 2 measurement positions, the tracking force can be measured up to 3 grams ※The adhesive on the memory part peels off and slides left and right. You can see the exterior, dullness, and feeling of use (Murakoshi Yoichi)
Accessories: original box, instruction manual
Main specifications: measurement range 0 to 3.0 g dimensions W140 x H15 x D25 mm weight approx. 20 g
※The needle tip is an external product. This is Type 4 of the classic V15 series. The impression is that sharper resolution and a sense of dynamism have been added than Type 3. It is a high-performance cartridge that has extremely high tracing ability and conveys the feeling that it picks up the sound engraved in the sound groove without omission (Murakoshi Yoichi)
Maintenance information: 2026.4.5 sound output confirmed
Accessories: none
Main specifications: mm type output voltage 4 mV needle pressure 0.75 to 1.25 g internal impedance 47 kΩ dead weight 7 g
The disposal price has been reduced. Member discounts are not applicable. 2026/2/28 sales price 298,000 yen Maintenance completed in 2017/2. Furniture-like vintage speakers It is slightly inefficient and requires power, but the low range with a sense of scale and the astringent mid-range are attractive. I think it goes well with classical and mood music. In addition to stains on the exterior and saran net, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2017.2.19 Maintained (exterior cleaning, top plate polishing/clear finish. Woofer part: unit detachment/terminal replacement, magnetic circuit slit cleaning, anti-rust edge, anti-noise maintenance set. Tweeter part: Cone-cured urethane removal Slit rustproof Magnetic circuit coil replacement and maintenance. B-199BC Part: Magnetic circuit slit cleaning, anti-corrosion, edge-free maintenance, etc.)
Accessories: none
Main specifications: 2 way 3 speakers sealed floor type low range 30 cm cone type 5 cm cone type x 2 allowable input 50 W playback frequency 40 Hz to 20 kHz crossover frequency 2.5 kHz impedance 8 ohms W686 x H762 x D409 mm approx. 41 kg
The price has been drastically reduced. 2026/3/30 sales price 198,000 yen Maintenance completed! Vacuum tube preamp. A preamp where you can enjoy the bright sound unique to vacuum tubes. Equipped with 3 PHONO inputs and 2 PHONO EQ OUT systems that output the same output as fixed. It is an amplifier with a high mid-range texture that reproduces music naturally with smooth sound quality (Murakoshi Yoichi)
Maintenance information: 2026.3.28 maintained (operation check, internal terminal repair) 2026.3.4 maintained (PHONO EQ SW, INPUTOSERECTOR SW disassembly contact polishing contact grease application, capacitor, etc. check, input/output operation check)
Accessories: power cable
Main specifications: 12AX7 x 3 12 AU7 x 3 PHONO 3 system, LINE 4 system (PHONO is for MM only) W500 x H186 x D326 mm 14.6 kg (actual measurement)
Speaker cable 6.0 m pair (approx. 6.0 m between terminal tips) Y lug specification is a staple popular PAD cable. The appeal of the medium to high range, which is delicate, and has a high texture, has not faded even now. It reproduces classical vocals with high quality. Serial 703099 (Fujisawa Yukishi)
Maintenance information: 2026.4.4 continuity confirmed
Accessories: No accessories
The price has been reduced! 2026/3/27 sales price 69,800 yen This is a record player sold by Project Audio to commemorate the 25th anniversary of its founding. It has a tasteful traditional frame design with a simple yet elegant finish. It's an easy-to-use player with advanced technology in a compact package. The exterior is dull. Serial 004595 (Fujisawa Yukishi)
Maintenance information: 2026.3.27 Operation confirmed
Accessories: instruction manual, connection cord, AC adapter, original box, cleaning cloth
Main specifications: 33,45 (manual speed variable) belt drive 30mm aluminum platter compatible cartridge weight 7.0g-14.0g W460 x H131 x D351 mm 10.2 kg
The classic 101 mm small speaker. One full range shot provides good coverage from bass to treble. It features a persuasive, bright, and tense sound. Since it is small, it can be placed anywhere, and you can enjoy the sound coming out of the front even at low volume. Small scratches and threads can be seen. Serial 639217, 639218 (Fujisawa Yukishi)
Maintenance information: 2026.3.29 Operation confirmed
Accessories: saran net
Main specifications: 1 way 1 speaker impedance 6Ω maximum input 150W output sound pressure level 86db W232 × H154 × D172 mm 2 kg
Audio-Technica's classic disc stabilizer. Recommended for those who don't have a stabilizer as an introduction (Futoshi Mikito)
Accessories: instruction manual
Main specifications: diameter 80 mm height 35 mm dead weight approx. 600 g
3.0 meter pair of XLR female to 3.5mm mini plug cables This cable transmits balanced (TRS, XLR) mono signals. How about headphone cables, etc. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2026.2.25 continuity confirmed
Accessories: none
Maintenance has been completed for the main volume and various switches, such as disassembly, polishing, and cleaning! Sony's classic 333 series model. The strengthened power supply makes the sound pressure feel solid and slightly appealing. Sounds with a sense of weight proportional to appearance are unique to this era. As for the phono circuit, you can enjoy the thick, sharp sound of analog discs with both MM and MC. There is a scratch on the wood panel on the exterior (Mizusaki Ryo)
Maintenance information: 2026.2.18 maintained (maintenance details/ ① main volume dismantling and cleaning ② switch disassembly and polishing (input selector, direct selector, speaker, mode, reckout, cartridge) ③ push switch disassembly and polishing (2 tone, T-over, source direct, mute, subsonic) ④ output relay replacement ⑤ power amplifier circuit part Sankin film resistor replacement ⑥ other volume (Cleaning, solder repair, ground reinforcement, interior and exterior inspection and cleaning, operation confirmation)
Accessories: copy of instruction manual
Main specifications: 105W+105W (8Ω) with phono MM/MC W470 x H165 x D435 mm 21.2 kg
Maintained! It's a thick amplifier that you can't imagine from its compact exterior. The good sound unique to QUAD allows you to enjoy not only classical music, but also jazz vocals in a mild way. The high level of musicality that makes you enjoy the music with a pleasant tone stands out. The urethane coating on the exterior has deteriorated, faded white, and some paint has peeled off (Wang Zhan)
Maintenance information: 2026.2.18 Maintained (pin jack replacement, power stage TV check, deteriorated capacitor, resistor replacement, operation check, due to specifications, pop noise appears when the power is turned on)
Accessories: copy of instruction manual, power cable.
Main specifications: output 140W+140W (8Ω) frequency characteristics 20Hz to 20kHz (-0.5dB) 13Hz to 40kHz (-1.0dB) total harmonic distortion ratio 0.01% or less (up to 130W 100Hz/1kHz) input sensitivity 0.5V input impedance approx. 20kΩ crosstalk 100dB (100Hz) 85dB (1kHz) 65dB (10kHz) S/N ratio 105 dB speaker minimum load 4 Ω external Dimensions W321 x H134 x D240 mm Weight 12 kg
Maintenance has been completed for the main volume and various switches, such as disassembly, polishing, and cleaning! Sony's classic 333 series model. The strengthened power supply makes the sound pressure feel solid and slightly appealing. Sounds with a sense of weight proportional to appearance are unique to this era. As for the phono circuit, you can enjoy the thick, sharp sound of analog discs with both MM and MC. The exterior has a feeling of use such as rust, small scratches, and dullness. Serial 211070 (Takahashi Nobuyuki)
Maintenance information: 2026.2.18 Maintained (main volume dismantling, cleaning, output relay replacement, switch disassembly and polishing (input selector, direct, reck-out, cartridge, speaker, mode, tone, source direct, subsonic, muting) power amplifier part resistor replacement solder main part repair earth enhancement volume sound wave cleaning pin jack polishing, interior and exterior cleaning, bias check, operation inspection)
Accessories: none
Main specifications: 105W+105W (8Ω) with phono MM/MC W470 x H165 x D435 mm 21.2 kg
The price has been drastically reduced. 2025/3/30 sales price 59,800 yen ※The diaphragm has been replaced with DR16R2421. The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance even when combined with various woofers and tweeters. The exterior has a small dent on one side of the diaphragm (Ryo Mizusaki)
Maintenance information: 2025.3.30 storefront operation confirmed
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms (measured 10/12 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Maintenance has been completed for the main volume and various switches, such as disassembly, polishing, and cleaning! Sony's classic 333 series model. The strengthened power supply makes the sound pressure feel solid and slightly appealing. Sounds with a sense of weight proportional to appearance are unique to this era. As for the phono circuit, you can enjoy the thick, sharp sound of analog discs with both MM and MC. There are line scratches and bumps on the exterior. Also, there are collapses and creases on the side panels. Serial 203598 (Tamura Eiji)
Maintenance information: 2026.2.3 Maintained (main amplifier section FET, adjustment volume, deterioration resistor replacement. Switch disassembly and polishing (input selector, direct, mode, speaker, recout, muting, subsonic, turnover, cartridge selector) main volume dismantling and cleaning. Output relay replacement. Earth terminal repair. Solder repair. Internal inspection and cleaning, pin jack polishing, bias adjustment, running test. *Please note that if you turn the SP terminal more than necessary, it will break. (The relay operates for about 15 seconds.)
Accessories: none
Main specifications: 105W+105W (8Ω) with phono MM/MC W470 x H165 x D435 mm 21.2 kg
The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance even when combined with various woofers and tweeters. There are small scratches, paint peeling, and there is small corrosion on some parts of the diaphragm (Oikawa Tetsuji)
Maintenance information: 2026.1.29 Operation confirmed
2012.8.11 Maintained (magnetic circuit overhaul, operation adjustment, replacement of sound absorbing urethane material)
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms (measured 10/12 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Maintained! The output volume has been added to enable detailed gain control with QUAD33. A classic British Quad stereo power amplifier. Small in size yet full torque. The sound, which is as deep as a tube amp, exudes an appeal that won't fade. The exterior has a feeling of use over time, such as dullness and small scratches. Serial 51928 (Takasaki Atsushi)
Maintenance information: 2025.11.26 Maintained (block condenser liquid leak → replaced with a replacement product because the original is not available, Lch board liquid leak scattering pattern leak → cleaning, resistance burn replacement. (Other C, R, TR check status OK, operation check)
2024.3.22 Maintained (internal all checks, Tr, C, R co-operation check*INPUT modification available, AC code created for cable creation)
Accessories: power cord, instruction manual (copy)
Main specifications: 45W+45W W120×H159×D324mm 8.2 kg
Maintenance such as disassembly of all switches and contact cleaning etc. was completed in 2025/5! Macintosh's classic preamp. It reproduces clear mid-range and glossy tones. This model should be used by music fans who enjoy all kinds of sources. The full range of functions, such as a 5-band equalizer and a 7-source input selector, is also attractive. There are small scratches and partial peeling on the exterior. Serial JEB8721 (Tomonori Asaine)
Maintenance information: 2025.5.14 maintained (RCA terminal solder fixed push switch, rotary switch, all switches disassembly contact cleaning contact grease coating main volume disassembly contact polishing cleaning conversion board creation replacement electrolytic capacitor replacement panel lamp replacement panel peeling correction each input/output operation check)
Accessories: copy of instruction manual
Main specifications: Equalizer up and down 12dB (center frequency/30Hz/150Hz/500Hz/1.5kHz/10kHz) rated output 20W+20W (8Ω) W445 x H192 x D395 mm 11.8 kg
The disposal price has been reduced. Member discounts are not applicable. 2025/10/18 sales price 79,800 yen It is cheap because the cone has viscoid drips on one side. Altech's classic woofer. Although it is ferrite, it produces bright bass with good emission. It's a sound method that puts emphasis on mid and low tones, so you can hear vocal breath well. Dullness, scratches, etc. can be seen on the exterior (Kobayashi Hitoshi)
Maintenance information: 2025.10.15 Operation confirmed
Accessories: none
Main specifications: 38cm woofer, 16 ohm, ferrite frequency band, 20 to 1000 Hz, 101 dB, recommended crossover, 500 Hz, baffle opening, 359 mm, baffle opening, 359 mm, rim outer diameter, φ408 x D162 mm, screw pitch: 380 mm, 10 kg
The disposal price has been reduced. Member prices are not applicable. 2025/11/21 sales price 50,000 yen JBL's classic front load enclosure 4560BK. You can experience the thick, energetic low frequencies unique to professional models. Metal stand with casters, with self-made wings. The screws on the back plate are missing, and there are only 2 screws on both sides. The wing plate is chipped and the screw is loose. The unit looks like it came with a D-130A-E. There are stains and stains on the exterior (Suzuki Keita)
Accessories: self-made wing, metal stand with casters ※ missing back screws
Main specifications: enclosure (including wings): W1667 x H915 x D625 mm 48.95 kg/1 (actual measurement) caster stand: W760 x H295 x D610 mm 11.25 kg/1 unit (actual measurement)
A classic disc stabilizer. The moderate weight gives a sense of stability for playing records. There is color fading due to sunburn (Tomoho Asaine)
Accessories: none
Main specifications: diameter 80 mm height 35 mm dead weight approx. 600 g
※1 bottle only. The horn used in the company's CP12II. Details are unknown. According to actual measurements, the throat diameter is 42 mm and the screw pidge is 104 mm.
Accessories: none
Main specifications: W300 x 205 x D165 mm 700 g throat diameter 42 mm screw fidge 10.4 mm (actual measurement)
※Shipping service. Special Issue No. 192 = Modern High End Speakers with [Classical] [Popular] Their Diverse Musical Expression/Thorough Audition of New Fall Models (Esoteric = K01X/K03X, Luxman = D08U/D06U, Vivid Audio = G4 GIYA, Magnepan = Mg3.7i, TAD = TAD Compact Evolution One, Weiss = Medus, Boulder = 2110, octave = HP700, Einstein = The Poweramp, Mark Levinson = No. 585, Kronos Audio = Sparta+Helena, Tekdus = TDC01 Ti)/Excellent Recordings in the Digital Age 20 Unknown Must-Listen Editions/Isabelle Faustong Interview/ Published 2014.9.2. Since the photograph is a sample, the actual product may be broken or there may be markings etc.
※Shipping service. Special Feature = All of the Latest Bookshelf Speakers (top) /Thinking about Audio Criticism (Sugano Okihiko) /Audio Life (Gomi Kensuke)/Published Models: PIONEER/SC-3000, SM-3000 LAX/L308 TEAC/TN-400 MICRO/MR-422, MR-622 PIONEER/CS330, CS-550 ELECTRO VOICE/SENTRY3 BOZAK/B-410 CLASSIC DUAL/DUAL701 MACINTOSH/MAC1900 JORDAN WATTS/JODRELL, JUPITER TLS GOLDRING/G820 SUPER E STANTON/60EE PICKERING/UV-15 2400Q LAX/L504, L-507 NIKKO/R-5000 JIMTEC/M-100, V-3 NAPOLEX/SS-3, ES- 100 KLIPSCH/CORNWALL GOODMANS/DIMENSION8 FISHER/ST-500, ST-530, ST-550 AIWA/AP-2050 TECHNICS/AP-2050, SL-120 ROTEL/RP-1000 GARRARD/ZERO100 THORENS/TD125MK2B MICRO/VF-6000, M-8000 TECHNICS/RS- 745U, RS-728U AIWA/AD-5500 INPERIAL/MK-1 Since the photograph is a sample, the actual product may be broken or there may be markings etc.
Mount adapter compatible with 35mm diameter speaker stands. This adapter is used when mounting speakers that do not have a hole in the bottom (Tetsuji Oikawa)
Main specifications: load capacity approx. 30 kg, stand mount diameter: 35 mm, base thickness: approx. 8 mm