Full overhauled! Laxman's inscription was revived by replacing capacitors, terminals, sockets, volume, etc. Dosy, thick timbre that cannot be heard in the current audio. In particular, you can feel the warmth and smoothness of classic strings and vocals alike. The appearance has a feeling of use such as scratches, dullness etc. Serial 10116437 (Makoto Kono)
Maintenance Information: 2021.3.2 Operation confirmed
2020.11.28 Maintenance (Vacuum Tube Socket Coupling Capacitor Electrolytic Capacitor Block Capacitor Diode Semi-Fixed Resistance Micro SW SP Pin Replacement SW/VOL (Completely decomposed contact polishing, oxidation and sulfide prevention grease coating offset bias adjustment input output waveform check distortion adjustment 1kHz sine wave, actual measured value 25W+25W sound output test)
Accessories: Operating instructions Copy power cord (general purpose)
Main Specifications: 30W+30W (4 8 16Ω) Line Input 4 System Phono 2 Series (MM) Pre-Power Separable W476 × H190 × D335mm 18kg
Speaker system with 3LZ Monitor GOLD in a small enclosed enclosure. I'm not good at orchestras, but small stringed instruments make me pretty beautiful. If you ring it with QUAD etc, the shade also expresses firmly. (Takahiro Inoue)
Maintenance information: 2021.3.2 Maintenance completed ([Exterior] Exterior repair, Polishing, Clear finish, Rear baffle painting, Saran net cleaning/retension [Unit maintenance] Magnetic circuit gap (Cleaning Center Adjustment [Network Maintenance] Unit Detachable, Terminal Installation)
Accessories: None
Main Specifications: Used unit 10 inch coaxial 2-way (3LZ MONITOR GOLD) Max Input 15W Impedance 8Ω Size W380 x H583 × D240mm Weight 13kg
Technics heavyweight high power amplifier A CLASS AA circuit with a voltage control current drive configured as a separate amplifier is adopted. Neutral and polite sound has a taste. The driving force that drives large speakers effortlessly is also attractive. Scratch on the bottom right of the front panel, there is a stain on the top plate and side (Yoichi Murakoshi)
Maintenance Information: 2021.3.3 sound sound confirmed
Accessories: None
Main specifications: Class AA amplification output 170W +170W (8Ω) output actual measurement 220W+220W (8Ω, 1kHz, JEITA) W476 × H209 × D475mm 33.7kg
Maintenance completed including pick-up exchange at TEAC service in 2018! By adopting 6N copper wire and high-quality parts for the internal wiring material, we upgrade the X-03 to X-03SE equivalent version. It makes me hear a precise sound with high resolution in a tight and tight sound image without coloring. ※ Audio Romanesque sticker is attached on the back (Sasaki Shota)
Maintenance information: 2018.9.19 Manufacturer maintenance completed (PU degradation exchange, belt replacement, comprehensive adjustment)
Accessories: Remote control, explanation, power cable, original box
Main Specifications: Renewable Disc: Super Audio CD/CD/CD-RW Digital Output/Optical 1/Coaxial/ilink1 Analog Output/Unbalanced (RCA) 1 System/Balanced (XLR) ) 1 system W442 × H153 × D353mm 23.5kg
Maintened! Rare Nakamichi's initial control amplifier. The company's unique triple transistor circuit and high-precision detent volume are packed with the company's commitment to realizing a groundbreaking strain rate and SN ratio at the time. There are two phono inputs that can be adjusted to the output of the cartridge by switching the input sensitivity on the back. There are stains on the front panel and dullness on the back (Yoichi Murakoshi)
Maintenance information: 2021.3.3 Maintenance (capacitor in power supply circuit, power lamp replacement. Panel switch, volume disassembly contact fix. (Input and output pin jack polishing.)
Accessories: Instruction manual
Main specifications: input line 3 system, phono 2 system ratio 0.003% W400 × H80 × D215mm 4kg
LINN's integrated amplifier network audio player. Built-in amplifier makes it easy to use, and you can enjoy network audio effortlessly. Soft and natural sound, perfect for those who want to enjoy casual music. There are abrasions and dullness on the top plate. (Yoichi Murakoshi)
Maintenance Information: 2021.3.3 Operation confirmed
Accessories: Remote control, instruction manual, power cord, source box
Main Specifications: Supported audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 supported sampling frequency 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192k Bits 16 - 24 Bit Input Terminals Ethernet Analog Voice RCA × 3 Front AUX × 1 MM phono digital voice coaxial RCA (SPDIF) × 3 TOSLINK (Optical) × 3 output terminal SP terminal 100W+100W W381 × H80 × D355mm Weight 5.0 kg
※ No seal of Rin Japan LINN network audio player. Simple yet modern European design, you can enjoy bright and untiring sound. It is compatible with LINN systems, as well as digital outputs that were not available in KLIMAX DS and AKURATE DS, and variable line-level output functions. There are thin abrasions on the top plate. (Yukishi Fujisawa)
Maintenance Information: 2021.3.3 Operation confirmed
Accessories: Remote control, instruction manual, power cord
Main specifications: Supported sampling frequency 44.1K, 48K, 88.2K, 96K, 176.4K, 192K, 16-24bit, output terminal RCA phono (fixed/variable line-level output), RCA phono coaxial (digital output) W381 × D360 × H80mm 4kg
※ It is inexpensive because there are many scratches and there is a dent on the grill. The speaker introduced the technology of the Nautilus series. CDM1 special edition model The unique space expression of B & W and the soft and supple sound quality of the high range of this series make you immerse yourself in music with peace of mind. Appearance is a lot of scratches and abrasions on the whole (Sasaki Shota)
Maintenance Information: 2021.3.3 Sweep Test Good
Accessories: Jumper plate
Main specifications: 2-way, 2 speakers 8Ω output sound pressure level 88db W220 × H370 × D274mm 8kg
Familiar Technica classic shell This is a must-have for analog enthusiasts who use it all over and over. Lead wires are not included. Slight scratches stand out in appearance (Kimiya Miura)
Accessories: No accessories
Main Specifications: Magnesium alloy body weight 10g
This is a Dynaco spherical control amplifier. It is an amplifier that you can enjoy the warm and pleasant sound peculiar to vintage. There is a sense of range, but the nostalgic sound with emphasis on atmosphere has a unique and irreable taste. Appearance has rust floats, dullness, and scratches due to deterioration. There are also some lettering disappearing. (Satoshi Yonejima)
Maintenance Information: 2021.3.3 Maintenanced (Repair of bad contact for each part. Vacuum tube 12AX7 replacement 2 x Electrolytic Capacitors 1μF Replacement 2 additional 1/2W resistors Block capacitor 30/20/20/10μF replacement. RCA jack and tube socket caulking repair (Other operation check)
Accessories: No accessories
Main Specifications: Vacuum Tube 12AX7×4, 12X4 Line Input 5 Phono 1 (MM) Preout 1 System W343 × H108 × D230 mm 4kg
LANCASTER with HPD315 The unit that sounds well balanced bright, is placed in a tannoy box with a sealed specification that allows you to feel its goodness. While being able to enjoy the classic color and gloss, vocal things are also harmoniously heard with the goodness of localization. Serial 203980/204640 (Kimiya Miura)
Maintenance Information: 2021.3.3 Maintenance (exterior repair, polishing, clear finish. Front and rear baffle painting Saran net cleaning, retension, fraying repair. Unit maintenance (low band side: edge exchange, magnetic circuit rust removal. Gap cleaning center adjustment, fastener rust removal cleaning, high range side: magnetic circuit rust removal/in-gap cleaning center adjustment). Network maintenance (output terminal brush, cleaning. Input terminal replacement (banana plug compatible). ATT (SW) contact cleaning. Frequency-characteristic measurement check (~42kHz) is performed and the original capacitor is continuously used for good results. (Input/output waveform, balance check, sound output check). unit desorption)
Accessories: No accessories
Main Specifications: 12inch Coaxial 2-Way (HPD315) Frequency Characteristic 20Hz to 20,000 Hz Allowable Input 85W Output Sound Pressure Level 92 dB 8Ω W535 × H840 × D320mm Weight 26kg/book
Brush up with internal and external maintenance! The 4311A of JBL was developed as a monitor speaker for studios and other monitors. It is a system I would like to recommend to customers listening to jazz/rock with good overall sound tightness and low range of nuke. Serial 25844/26045 (Kimiya Miura)
Maintenance Information: 2021.3.3 Maintenance (exterior repair, all paint. Create a new Saran net Woofer cone paper painted Network maintenance (internal connection terminal (Faston) new replacement. ATT Brand New Replacement Frequency-characteristic measurement check (~42kHz) is performed and the original capacitor is continuously used for good results. (Input/output waveform, balance check, sound output check). unit desorption)
Accessories: Saran net
Main specifications: 3-way, 3-speaker, Bass reflower system, bookshelf type use unit/30cm cone type for low range (2213) /13cm cone type for middle range (LE5-2) /3.6cm cone type for high range ( LE25) Frequency Characteristic 45Hz to 15kHz Allowable Input 40W (RMS) 8Ω Crossover Frequency 1.5KHz, 6kHz Output Sound Pressure Level 91 dB Dimensions W362 × H597×D298mm Weight 19kg
Lanzaroy edge softened! A classic vintage woofer that has been used for a long time from OLYMPUS D50S12 and Lancer 101 in the mid-1960s to L220 in the late 1970s. The dry and weighted sound is exactly perfect for old jazzs. Serial 88354/88468 (Kimiya Miura)
Maintenance Information: 2021.3.3 Maintenanced (edge softening treatment, corn paper painting)
Accessories: No accessories
Main specifications: 36cm cone type woofer unit impedance 8Ω depth 137mm Weight 8.2kg
※ Set of 4 Acoliba's RCA short pin Fully non-magnetic structure using materials with excellent acoustic and vibration suppression. The sound quality is improved by shorting the input terminals that are not used. ※ Please do not insert it in recOUT or output terminal. We do not guarantee that sound goes out or if it fails by any chance. Feeling of use, there is dullness. (Takasaki Takasaki)
Accessories: None
Low noise power strip for PSE standard This tap was developed for the purpose of removing external high-frequency noise, internal radiation noise reduction, electromagnetic wave removal, and reducing electrical contact resistance. It is mild and thick sound quality. The appearance leaves a feeling of use. Serial 05691 (Hiroshi Kondo)
Maintenance Information: 2021.3.2 Conduction Check
Accessories: None
Main Specifications: Rated Capacity 15A (Output Outlet) 4 Mouth Hubbell Hospital Grade W170 x H90 x D170mm Weight 2kg
Digital needle pressure meter with backlight for easy viewing and measuring. It also features an auto power-off function, which automatically turns off after 120 seconds. It is a convenient item to have one. (Itsuro Mizushima)
Maintenance Information: 2021.3.3 Operation confirmed
Accessories: original box
Main specifications: Load measurement range 0.02 to 15.0 g Measurement accuracy 0.05 g External dimensions 96 × 43 x 20 mm Weight 50g
A limited quantity genuine leather record cleaner developed by JICO/Nippon Seiki Jewelry Industry with particular attention. Handmade item using the same leather and yarn as the European bag maker (KONDO Hirotsugu)
Accessories: None
Set of 2 optional weights for DENON DP-1300MK2 Use when using heavyweight cartridges. (Itsuro Mizushima)
Accessories: None
Main Specifications: Compatible cartridge own weight/for 20-28g (small) /for 26-37g (large)
※ ZERO SHOT low price because it is out of stock. Charged erasers It is a goods to remove static electricity by placing records and CDs in a case lined with felt that has the effect of removing electricity and pressing ZERO SHOT. ※ Since we have not verified the power removal, we will pass it as the status quo. (Itsuro Mizushima)
Accessories: None
Main specifications: H40 × W340 × D340mm ※ ZERO SHOT shortage
Audio-Technica Classic Disc Stabilizer Moderate weight gives the record board a sense of stability. Overall there is a feeling of use such as dullness and rubbing. (Itsuro Mizushima)
Accessories: None
Main Specifications: Diameter 80mm Height 35mm Self Weight Approx. 600 g
Head shell made of aluminum die-cast from the manufacturer unknown. Easy to use with a simple design seems to be good. (Itsuro Mizushima)
Maintenance Information: 2021.3.3 Conducted Confirmed
Accessories: None
Main Specifications: Self weight 12g
Set of 5 Smaller insulator than RFS-66 It has a structure with a metal belt attached to ebony. There is a feeling of use. (KONDO Hirotsugu)
Accessories: None
Main Specifications: Diameter 32 x Height 25mm 82g/1pc
Set of 4 A good insulator with a solid construction in an easy-to-use size. It has a structure with a metal belt attached to ebony. There is a feeling of use. (KONDO Hirotsugu)
Accessories: None
Main specifications: diameter 50 x height 26mm 220g/1 piece
Set of 3 Spike Bases for J1 Project Hybrid type spike base with Diamond like carbon coating on the stainless steel part. (Itsuro Mizushima)
Accessories: None
Main Specifications: Diameter 35mm x Height 15mm
Set of 4 Spike Bases for J1 Project It is a hybrid type spike base that combines resilient hard material ICP composite and stainless steel material. (Itsuro Mizushima)
Accessories: None
Main Specifications: Diameter 35mm x Height 15mm
Magnesium audio board The material uses the finest material called pure magnesium plate and Russian birch hybrid. Simply place it under the device to realize improved resolution and increased dynamic range. There is a feeling of use. (Takasaki Takasaki)
Accessories: None
Main Specifications: Magnesium part W395 × D295mm Whole W415 × H15 × D315mm
※ Set of 8 Unknown manufacturer spike base. It seems to be made of brass. There is a feeling of use such as darkening and abrasion on the whole. (Itsuro Mizushima)
Accessories: None
Main Specifications: Diameter 22mm x Height 6mm
※ Set of 4 Insulator that employs Technica's proud honeynight The 4-layer hybrid structure exhibits excellent vibration damping effect while small. The base material is luxurious specification of brass shaved out. (Takasaki Takasaki)
Accessories: None
Main specifications: Hybrid structure Special anti-vibration rubber honeynight, Sorbosane is effectively placed load capacity 5kg (1 piece) W30 × D17mm Weight approx. 65g/pcs
An eye-catching Lux primaine amplifier with unique indicators. Traditional rack stone, vacuum tube soft and warm mid and low range The hardened sound quality speakers also sound mildly. There is a little feeling of use. Cereal 114002056 (Takasaki Takasaki)
Maintenance Information: 2021.3.3 Maintenance (Panel switch disassembly can be disassembled and polished contact. Transistors and capacitors have been replaced before. (I/O pin jack polishing)
Accessories: Copies
Main specification: 40W+40W (8Ω) W443 × H153 × D273mm 9.3kg
※ bonnet shortage. Replica model of the inscription MODEL 8B It seems that the power of reproducing faithfully to the original as possible. Delicate, gentle and transparent tones can be enjoyed. Bias can be adjusted even if you replace the vacuum tube of your choice. Feeling of use, dullness, small scratches scattered. Serial F010531 (Takasaki Takasaki)
Maintenance information: 2021.3.3 Maintenanced (both ch both tubes failed at check, noise generated by vibration → exchange (GE 6BH6), other internal C, R check OK, Output bias check ok)
Accessories: Power cord ※ bonnet shortage
Main Specifications: 35W+35W Vacuum Tube 6CG7/6BH6/EL34 W348×H191 × D273mm 22.5kg
Maintened The famous horn 175DLH for its crisp, dry and rich sound. Although it is a scatter sound, it is an honorable one of the inscription machines where the beehive lens disperses the sound with a thick sound not too hard. There are aging dullness stains, paint peeling etc. Cereal 16032, 16043 (Makoto Kono)
Maintenance information: 2021.2.16 Maintenance completed (Diaphragm mounting adjustment
Insulation Washer Pad Dumpnerbis Replacement for each) DCR16032 (6.4Ω diaphragm with small scratches) DCR16043 (6.4Ω diaphragm no scratch)
Accessories: None
Main Specifications: LE175/1 inch Driver 8Ω Maximum Sound Pressure Level 108 dB Frequency Characteristic 800Hz to 15KHz Directivity 60 Degrees (Cone) Allowable Input 30W W145 × H145 × D270mm 5.9 kg
Disposal price drop (not applicable for membership discount) (2021.1.11 selling price 450,000 yen) Maintained inside and outside. The JBL Professional Series speaker combines the middle and high range of the viral horn characterized by wide directional characteristics, and a 38cm woofer that is attractive for fulfilling low-range playback. You can enjoy a variety of music centered on jazz-punch sound quality. Cereal 283201/283360 (Takasaki Takasaki)
Maintenance information: 2020.10.20 Maintenance completed (exterior repair, polishing, oil finish (top plate veneer new paste), front and rear baffle, Hakama repair, paint, Saran net rework. Woofer Edge Refill, Corn Paper Paint Driver magnetic circuit rust removal · In-gap cleaning center adjustment, sound absorbing material replacement, screw exchange, terminal contact cleaning. Soldering terminals on network boards, terminal rust pickling treatment and cleaning, replacement of mounting screws, ATT (L-Pad) new replacement, ATT (POT) contact cleaning, INT/EXT switching SW contacts Sulfide removal, scrubbing, cleaning, frequency characteristics measurement check (~ about 42kHz), continued use of original capacitors for good results, input and output waveform and balance check, sound output check)
Accessories: None
Main Specifications: 2way vial horn 2235H/2421A 93dB W556×H908 × D480mm 79.5kg/1
Significant price reduction. 2021.3.1 Selling price 248,000 yen teal floor-type speaker that follows the traditional design. All units use aluminum alloy diaphragms, high SN height and rigidity resistance, making you feel the high quality of sound itself. It produces crisp, clear sound with high regenerative ability and rich expressiveness. There are light Kusumi and dirt (Yoichi Murakoshi)
Maintenance Information: 2021.2.27 Operation confirmed
Accessories: Spike
Main Specifications: 3-Way, 3 Speaker, Passive Radiator Method, Floor Type Bandwidth 33Hz to 37000Hz Sensitivity 87dB Impedance 4Ω Crossover 900Hz (Electrical) 3000Hz (Mechanical) Recommended Power Amplifier Output 100W to 400W W280 × H1,054 × D356mm Weight 32kg
Price down (2021.2.21 selling price 10,000 yen) * Current sales item. Compact yet sturdy speaker with heavy contents You can enjoy the strings, guitars, and vocals of the violin that lustrous and sticky. Feeling of use, dullness, scar wounds. Serial 6Y093118 (Takasaki Aki)
Maintenance Information: 2021.2.21 Sound out confirmed
Accessories: Saran net
Main Specifications: 2 Way 2 Speaker Bass Ref Type 4Ω 82dB W156 x H49 x D221mm 4.1kg
Power Cable 1.5 m High-OFC Soft Copper Wire Adopts High-purity Silver-Coated Cable with a low center of gravity, thick sound quality, and delicately listening to the lingering and sound. There is a feeling of use. (Takasaki Takasaki)
Maintenance Information: 2021.2.28 Conducting Confirmed
Accessories: None
Price drop (2021.2.25 selling price 69,800 yen) It is ONKYO's classic best-selling amplifier that has dominated the world with a sense of transparency and clear sound quality. Ease of use without choosing a preamp is attractive. Although it is as powerful as it looks, it is a sound quality that is persistent and less tired of listening. The hard black design is also good. Overall feeling of use, Slight Scratch scattered. Cereal 34041745 (Takahiro Inoue)
Maintenance Information: 2020.4.23 Maintenance (Power Switch Guide Disconnect Installation Correction)
2019.7.17 Maintenance carried out (Main amplifier output relay replacement. Meter lamp replacement at output Indicator lamp replacement. Solder repair, internal inspection cleaning, panel glass cleaning, sidewood polishing, output waveform and left and right output level*1KHz 1W, volume cleaning, operation check)
Accessories: None
Main Specifications: 170W+170W (4Ω) 130W+130W (8Ω) Frequency Characteristic 1Hz to 100kHz Impedance 4Ω to 16Ω W480 × H174 × D422mm 20.5kg
Significantly reduced price! 2021/2/27 selling price 178,000 yen first stock, DALI OPTICON 6 has arrived! The woofer uses woodfiber cone, and the tweeter is equipped with a 28mm dome tweeter and a ribbon tweeter. In addition to the high middle and high range of the traditional texture, it is an attractive series where you can feel the height of the response newly. Appearance, there is no noticeable scratch. Serial 1927852R/L (Satoshi Yonejima)
Maintenance Information: 2021.2.27 Sweep Test Good
Accessories: Saran net, spike, hex wrench
Main specifications: Bass reff type frequency characteristics 49Hz to 32kHz Efficiency 89 dB impedance 4Ω W195 × H1,001 × D330mm Weight 18.9 kg
A model commemorating the 250th anniversary of J.S. Bach's death. 6N silver wire coil is adopted. While leaving the orthophon likeness, it is a cartridge that is good for even more delicate space expression. The know-how of the masterpiece Jupilie has been fully introduced, and the high cost performance stands out. There is no noticeable scratch on the appearance (Satoshi Yonejima)
Maintenance Information: 2021.2.27 Operation confirmed
Accessories: Instruction manual, original box
Main Specifications: Output Voltage 0.45mV Frequency Characteristic 20Hz to 35kHz Internal Resistance 5Ω Oval Suitable Needle Pressure 2.5g Self Weight 10g
I cut the price! 2021/3/1 Sales price 148,000 yen TWQT type using speaker unit Fostex FE103A housed in a wooden cosmetic box planned and manufactured to commemorate the 70th anniversary of Foster Electric It's a speaker. The finish of the appearance is very beautiful with the specification of Sapele veneer and urethane clear coating. Based on high-grade Cina plywood, MDF is used in points to control the sound of a well-balanced sound so you can listen to a large scale sound. The appearance does not have noticeable scratches. (Kimiya Miura)
Maintenance Information: 2021.3.1 Sweep Test Good
Accessories: Unit original box
Main Specifications: 10cm Full Range Impedance 8Ω Efficiency 88dB Size W185 x H864 × D291mm Weight 8.8kg
Significantly reduced price! 2021/2/27 Selling price 1,780,000 yen ※ Armless type. Comes with dust cover One side will be SME 3012. Luxury player system announced to commemorate the 100th anniversary of the establishment of THORENS. The sound coming out of the super class turntable will be heard until now unplayable sounds that other players can't taste. Appearance, there are scratches and dullness. Serial 051 (Kimiya Miura)
Maintenance Information: 2021.2.27 Maintenance (Electrolytic Capacitor Replacement. Belt replacement. Rotational motion check. lubrication)
Accessories: AC adapter, dust cover
Main Specifications: Quartz Control Belt Drive with 2-Phase 16 Pole Synchronous Motor 33/45/78rpm Turntable Double Structure (7.9 kg) Body: W610 x H290 x D520mm Approx. 60kg
I cut the price! 2021/2/23 Sales price 12,800 yen Ortofon's MC series basic model. I also meet uptempo music because it sounds spooky. Come also as an introduction to Ortphone. Serial 134149 (Kimiya Miura)
Maintenance Information: 2021.2.23 Operation confirmed
Accessories: No accessories
Main Specifications: MC type oval needle 0.09 mV 3Ω needle pressure 1.3-1.8 g own weight 7g
Significantly reduced price! 2021/3/1 Entry Primain Amplifier with a sales price of 248,000 yen accupase. Equipped with the same AAVA volume control as the upper model E-560 etc. While an introductory machine, it boasts the perfection that makes you feel the height of quality that seems to be Accuphase everywhere. The appearance does not have noticeable scratches. Serial L2Y149 (Kimiya Miura)
Maintenance Information: 2021.3.1 Operation confirmed
Accessories: Remote control, instruction manual, power cable, original box
Main Specifications: 115W+115W (6Ω) 105W+105W (8Ω) W465 × H151 × D420mm Weight 20kg
I cut the price! 2021/3/2 The sale price 128,000 yen SA-15S2 is a special model based on the SA-15S2, which introduced high-definition parts and made high sound quality. It is a CD player with bright, open and delicate sound. By connecting with a digital device with an external output, it can also be used as a D/A converter. Appearance, there is a kusumi. Serial 200000927000 (Satoshi Yonejima)
Maintenance Information: 2021.3.2 Operation confirmed
Accessories: Remote control, instruction manual, power cable
Main Specifications: SACD part/2-channel playback frequency range 2Hz to 100kHz Frequency characteristics 2Hz to 50kHz (-3dB) Dynamic Range 112 dB Harmonic Distortion Rate (1kHz) 0.001% CD part/2-channel playback frequency range 2Hz to 20kHz Frequency characteristics 2Hz to 20kHz Dynamic range 100dB or more Harmonic Distortion (1KHz) 0.0015% Size W440× H127 x D419mm Weight 14.5 kg
Significantly reduced price! 2021/3/2 The model brushed up from the sale price of 448,000 yen Nautilus 803. The woofer has also been changed to a carbon cone and has been version up from the previous work. In addition to the size of the resolution and sound field, the stability of the low range is also sufficient. It is still a speaker with a high degree of perfection. Appearance, there are scratches and small scratches. Serial 0009230/0009230 (Satoshi Yonejima)
Maintenance Information: 2021.3.2 Sweep Test Good
Accessories: spike, saran net, jumper cable
Main Specifications: 3 Way 4 Speaker Rose Nut Bass Ref Type Efficiency 90dB Impedance 8Ω W291 × H1063 × D433mm 41kg
I cut the price! 2021/3/2 Selling price 198,000 yen Marantz is a classic primaine amplifier. Equipped with a digital volume that can be finely adjusted. SN goes up than the previous model and the texture of the middle and high range is up. The sound field feeling is also widely secured, making it a high-definition sound beyond the price. Appearance is dullness and scratches on the selector knob. Serial 2000000000 (Satoshi Yonejima)
Maintenance Information: 2021.3.2 Operation confirmed
Accessories: Remote control, instruction manual, power cord
Main Specifications: 100W+100W (8Ω) W440 × H168 × D44mm 26.6kg
Significantly reduced price! 2021/3/1 priced 248,000 yen Bellair vacuum tube preamp with phono. Simple configuration yet reproduces transparent and delicate sound quality. The smooth and relaxed sound quality is suitable for female vocals, stringed instruments. Appearance has a small scratch on the bottom of the front panel. Serial 10030326 (Kimiya Miura)
Maintenance Information: 2021.3.1 Operation confirmed
2018.8.4 Maintenanced—Constant voltage discharge tube (vacuum tube) replacement, SW, VOL disassembly cleaning, appearance cleaning, output waveform confirmation, sound output test conducted)
Accessories: Power cable
Main Specifications: Vacuum tube used: Philips ECC6189W x 2 murrard10BC1×2 GE 6201×2 Size W445 ✕ H115 ✕ D360mm Weight 17kg
Significantly reduced price! 2021/2/28 Selling price 2,680,000 yen*50Hz specification. Very unusual, the predecessor of 927 R80S has arrived! Cereals are also 21 young and quite rare individuals. Originally it was 220V specification, but we have changed it to 100V for easy use. This time only phono motor, ortofon RMA297 and EMT 997 can be mounted. * A fan is built into the motor, and the fan sounds during operation. Appearance, such as scratches and paint peeling. Cereal 21 (Eiji Tamura)
Maintenance Information: 2021.2.28 Maintenance (Specification changed to 100VAC. 50Hz specification Cleaning Replaced fuse module Replaced power transformer 100V specification, wiring fix. Power cord creation. Motor removal, disassembly, internal rust removal, pulley alignment, felt lubrication, assembly and adjustment Speed adjustment mechanism reinforcement, assembly, adjustment. Main bearing ball replacement Added main TT rubber ring Neon lamp replacement. Motor variable resistance break, replace rheostat. Arm lifter mechanism production. Idler replacement. Oil (50ml) attached. Running test OK)
Accessories: oil, power cable, usage instructions
Main Specifications: 100V/50Hz Specifications Adaptive Arm OrtoFon RMA297 · OrtoFon RF297 · EMT 997 W670 ✕ H240 ✕ D518mm
I cut the price! 2021/2/24 Sale Price 79,800 yen Vacuum Tube Stereo Power Amplifier. Bright and fresh sound like DYNACO. The middle range is thick and has a sense of temperature and sounds more powerful than I thought. It is an amplifier that you want to sound together with JBL and Altec etc. Appearance has aging corrosion and dullness (Kimiya Miura)
Maintenance Information: 2021.2.24 Maintenance (ACON ~ Check, Small distortion output, tube, socket replacement. Interstage coupling C exchange, rubber foot mounting)
Accessories: No accessories
Main Specifications: Tubular Stereo Power Amplifier Output Continuous 17.5W+17.5W Peak Output 40W+40W Frequency Characteristics 10Hz to 40kHz Damping Factor 10 (20Hz to 20kHz) Used Vacuum Tubes 7247 ✕ 2 6BQ5 ✕ 4 Silicone Diodes ✕ 2 Pieces Size W330 ✕ H110 ✕ D160mm Weight 6.4kg
I cut the price! 2021/3/1 A built-in phono equalizer board with a sales price of 37,800 yen accupase. For analog record playback, the internal dip switch allows setting MM/MC equalizer gain switching, MC input impedance, and subsonic filter ON/OFF. The appearance does not have noticeable scratches. L2W364 (Kimiya Miura)
Maintenance Information: 2021.3.1 Operation confirmed
Accessories: original box
Main Specifications: Compatible models: C-2000, C-245, C-265, CX-260, E-307, E-308, E-407, E-408, E-530, E-550, E-350, E-450, C-2110 * In the case of E-550/E-350/E-450/C-2110, MC/MM can be switched on the panel, so there is no need to set on board.