Replacement needle compatible with National EPS-19ST Operation has not been confirmed since there is no main unit (Hiura Katsuji)
Maintenance Information: Operation Unconfirmed
Accessories: original box
The price has been reduced. 2024/5/24 sales price 35,000 yen Tannoy rectangular yoke type enclosure by Shinkosha, a popular manufacturer of domestic boxes. It is attractive because it is made to sound good. A 30cm unit adapter (detachable) is attached to the baffle surface, and casters are attached to the bottom (Murakoshi Yoichi)
Accessories: none
Main specifications: W597 x H108 x D37 mm weight 30 kg
Currently sold. This is a self-made 10cm full-range 1-way speaker with unknown details. There is no problem with the sweep or music signal, but the current situation is because it is cheap. There are bond marks on the exterior and center cap, and a feeling of use can be seen, such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.3 sound output confirmed
Accessories: none
Main specifications: W120 x H200 x D122 mm 2.5 kg (actual measurement)
A self-made record cleaner that imitates PAROSTATIK. The core inside is a vinyl sheet wrapped around it. Thanks to the soft core, it is exquisitely comfortable to use. The exterior has a frayed feeling of use (Katsuji Hiura)
Accessories: none
Main specifications: W105mm diameter 30mm weight 9g
The disposal price has been reduced. Member discounts are not applicable. 2024/2/22 sales price 8,000 yen. Self-made cabinet for DENON DP-3000. The arm was attached to the company's DA-305. When the four-square screw is removed, it is divided into 3 plates, making it easy to perform processing such as drilling. There are scratches, fading, stains on the main body, cracks, repairs, fading, stains, and adhesive tape marks on the dust cover (Kanai Hidetsugu)
Accessories: dust cover
Main specifications: W600 x H112 (H202 with dust cover) x D500 mm 12.6 kg (actual measurement, dust cover included)
The price has been reduced. 2024/5/20 sales price 30,000 yen A FOSTEX HA21 throat adapter is set on a self-made horn with a size that imitates the FOSTEX H320. If you've been looking for this size, take this opportunity! You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: throat diameter 100 mm pitch 4 holes 60 mm 3 holes 50 mm overall W635 x H110 x D 455 mm kg (actual measurement)
The price has been reduced. 2020/4/17 Selling price 5,000 yen Unspecified wooden front baffle. If you are a self-made group, come on. There are scratches and stains scattered, uneven painting, corner chips, etc. (Takasaki Atsushi)
Accessories: none
Main specifications: opening diameter 280 mm bass reflex opening W292 × H80 mm W400 × H610 × D20 mm 1.8 kg/sheet
1 pair of unspecified speaker stands Attention can also be seen, such as constructing a metal circular insulator. If you've been looking for this size, go for it. The exterior, paint unevenness, dullness, abrasions, etc. can be seen a lot of feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: W450 x H240 x D450 mm 12 kg (actual measurement)
Tokyo soundproof turntable seat using vibration-absorbing rubber. The vibration convergence time is overwhelmingly fast, and it effectively absorbs unwanted vibrations in the frequency band that is important for music playback. There is a slight linear stain on the surface (Murakoshi Yoichi)
Accessories: case
Main specifications: size 4 mm thick x 291 mm diameter weight 330 g
TRIO N-39 compatible needle. This is a replacement needle for TRIO V-39. Operation not confirmed (Murakoshi Yoichi)
Maintenance information: operation unconfirmed
Accessories: original box
Maple type. Stand for small speakers made of solid Yonematsu. Compatible with most small speakers. The combination of Corian base and wood block material makes it resonate aggressively and accentuates the sense of spaciousness and depth. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: 6 spacers
Main specifications: W280 x H615 x D370 mm 6.6 kg
This is a specially designed product in which the company's original neighboring bronze machined pin terminals are set on the HS-1A using African ebony wood, and 6N copper wire with excellent sound quality is used as the shell lead. Since lead wires are soldered to the terminals on the arm side, sound quality improvement effects can also be expected due to a reduction in electrical contacts (Murakoshi Yoichi)
Maintenance information: 2024.6.11 continuity confirmed
Accessories: mounting screws
Main specifications: African ebony wood (eco-paint buff finish), brass finger tips (non-magnetic gold plated finish), own weight 10.2 g
This is a replacement needle compatible with Hitachi MFS-250. Unopened Operation has not been checked (Hiura Katsuji)
Maintenance Information: Operation Unconfirmed
Accessories: original box
This is a replacement needle for Hitachi. Compatible with MFS-250. Unopened Operation has not been checked (Hiura Katsuji)
Maintenance Information: Operation Unconfirmed
Accessories: original box
This is a woofer mount adapter that is thought to be used to convert a 38cm unit hole to a 30cm unit. The previous owner attached it to the JBL C38 BARON. The exterior and bolt mounting part of the individual on one side are damaged, and there is a feeling of use due to dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: mounting screw pitch: outer circumference: 370 mm, inner circumference: 293 mm; caliber: 270 mm; external dimensions: W356 x H365 x D10 mm; approx. 0.4 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/3/1 sales price 12,000 yen. This is a heavy weight that can be used with the Pioneer PL-70L2. If you've been looking for one, why not take this opportunity? There are dull stains all over (Murakoshi Yoichi)
Accessories: none
Key Specifications: Weight 177g
Unspecified set of 2 wood blocks 30mm square insulator cube It is similar to Yamamoto Sound Crafts's QB-1, but it is smaller than the QB-1 and the details are unknown. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Main specifications: W30 x H30 x D30 mm 28.6 g (actual measurement)
The disposal price has been reduced. Member discounts are not applicable. 2023/129/7 sales price 5,000 yen. 1 piece only. Phase plug for B&W 800 series. It is probably thought to be machined stainless steel, but details are unknown. How about for those looking for a center speaker such as HTM1 (Murakoshi Yoichi)
Accessories: none
Main specifications: 223g/1 piece
Unspecified weight for 3012R. It can be attached to the 3012R shaft, but detailed uses are unknown. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: dead weight 86g
※Since there are 3 missing corners, it is inexpensive. Sorbothane Square Insulators, Set of 4, Black Type When vibration is cut with sorbocaine, a phenomenon occurs where low frequencies clearly and dynamically come out of the speaker itself. The exterior is dull, etc., and there is a feeling of use (Murakoshi Yoichi)
Accessories: none
Main specifications: size 30 mm square height 10 mm
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer The terminal is male and cannot be used as a microphone. There are a few indelible writing marks left on the plug (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
XLR cable 5.0 m male to female details unknown. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.9 continuity confirmed
Accessories: none
An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
Unspecified speaker stand. It's the size of JBL4312 and DIATONE's DS-77 class. If you've been looking for one, please take this opportunity. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: top plate W340 x D245 mm overall W380 x H437 x D340 mm 6.2 kg (actual measurement)
Unspecified wood cabinet. You can see a feeling of use, such as appearance, dullness, scratches, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W470 x H134 x D310 mm 2.2 kg (actual measurement)
The price has been reduced. 2024/4/11 sales price 5,000 yen. Wood cabinet with unknown compatible models. The internal dimensions of the cabinet are W432 x H123 mm, there are 4 rubber feet on the bottom, and there is a hole (203 x 93 mm) with a metal grill in the center. There is a feeling of use and dullness (Kanai Hidetsugu)
Accessories: none
Main specifications: external dimensions W450 x H162 (including legs) x D267 mm 1.8 kg
XLR female to mono mini jack cable 4.5m unusual combination microphone cable. Can also be used as a normal microphone cable using standard jack conversion (Murakoshi Yoichi)
Maintenance information: 2024.4.11 continuity confirmed
Accessories: none
※1 piece only (male to male) XLR cable 1.5 m interconnect cable with unknown manufacturer. There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
Unspecified set of 4 banana plugs If you've been looking for one, go ahead. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
The price has been reduced. 2024/1/5 sales price 400 yen. ※1 bottle only. 3 cm unit with unknown details. Since the size and condenser is attached to the plus side, it seems to be a tweeter. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2022.11.15 Operation confirmed
Accessories: none
Main specifications: actual impedance measurement 3 ohms 3 cm
The price has been reduced. 2023.1.21 Sales price 2,000 yen Plastic cover for 28cm units of unknown manufacturer. Outer frame and inner ring set There are abrasions and a feeling of use (Kanai Hidetsugu)
Accessories: none
Main specifications: maximum dimensions W372 x H28 mm inner diameter 270 mm outer 4 holes diagonal screw pitch 345 mm inner ring diagonal screw pitch 289 mm
*1 bottle only Speaker stand with unknown details such as manufacturer name and model. There are appearance, abrasions, and dullness (Hitoshi Kobayashi)
Accessories: none
Main specifications: W280 × H270 × D330 mm 4.8 kg (actual measurement)
This is a self-made baffle made in a size like JBL VICOUNT or BARON. There is a hole for the 38cm unit to fit, and a hole that is thought to be for a screwdriver. In the screw hole
Accessories: none
Main specifications: woofer section screw pitch 370 mm aperture φ343 mm driver opening 133 mm external dimensions W443 x H518 x D20 mm weight approx. 1.5 kg (one side, actual measurement)
Only 1 bottle unopened! Unspecified XLR (male) to XLR (female) relay plug. The exterior is good (Kobayashi Hitoshi)
Maintenance information: unopened, unchecked
Accessories: none
manufacturer unknown. It seems to be a compatible needle for portable players whose details are unknown (Hiura Katsugu)
Maintenance information: operation unconfirmed
Accessories: none
Disposal prices have been reduced. Member discounts are not applicable. 2018/10/24 Sales price 3,000 yen These are parts made in Mexico whose details are unknown. There is rust, dirt, etc. (NAGAI Michio)
Maintenance Information: 2018.10.24 Conductivity Confirmed
Accessories: none
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.17 Conductivity confirmed
Accessories: none
Unspecified XLR (male) to RCA (female) conversion plug only. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.8.14 Confirmation confirmed
Accessories: none
Main specifications: No. 2 HOT
The price has been drastically reduced. 2023.9.5 sales price 8,000 yen. Set of 8 unspecified JBL speaker mount parts MA15 type. There is a feeling of use on the exterior, paint peeling, etc. (Kobayashi Hitoshi)
Accessories: none
The price has been drastically reduced. 2024/1/4 sales price 500 yen. Self-made audio board with unspecified details. Audio board made by wrapping cloth around the board. The board material is unknown. There is a lot of feeling of use on the exterior, scuffs, scratches, stains, torn cloth, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W460 x H40 x D350 mm 4.6 kg
The price has been reduced. 2023.4.10 Turntable seat with sale price 2,000 yen unknown manufacturer. The material is soft and can be expected to have a vibration suppression effect. The exterior is scratched, dirty, and dull, and there is a feeling of use (Katsutsugu Hiura)
Accessories: none
Main specifications: thickness 4mm
1 pair of unspecified speaker terminals. The construction is solid. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none