An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
SAEC ceramic shell A beryllium copper washer and a three-point crimping system are used at the arm joint. The overhang can be adjusted by means of a slide plate on the top. There is a cloudy part (Daiki Goto)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: sintered aluminum oxide body, 3-point crimping type, weight 18 g
SAEC headshell Lightweight, non-resonant head shell made of aluminum light alloy composite. It's light, easy to use, and has an appealing sound that sounds straightforward. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.6.10 continuity confirmed
Accessories: No accessories
Main specifications: aluminum alloy with a dead weight of about 8 g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Murakoshi Yoichi)
Maintenance information: 2024.6.16 sound output confirmed
Accessories: mounting screws
Main specifications: aluminum stamping dead weight 8g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Oikawa Tetsuji)
Accessories: none
Main specifications: aluminum stamping dead weight 8g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Mizusaki Ryo)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Mizusaki Ryo)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g
A popular SME classic headshell with a stylish design. Not only is it stylish, but it is also a valuable shell that is light and strong, which is essential for light needle pressure arms and heavy cartridges (Kojima Yosuke)
Accessories: none
Main specifications: aluminum stamping dead weight 8g
*Lead wire missing. An NR (Non Resonance) head shell with the shell body and plug part integrally molded. It has a structure where the main body is tightened from the top and bottom with a finger plate and cartridge, there is no need for a stop nut, and it comes with an overhang adjustment memory, making it easy to set up. (FUJISAWA KOSHI)
Maintenance information: 2024.6.10 continuity confirmed
Accessories: none
Main specifications: dead weight approx. 10 g (actual measurement)
Alloy die-cast headshell I like the simple design. This is one that is easy to match with various cartridges (Shota Sasaki)
Maintenance information: 2024.6.8 confirmed
Accessories: none
Main specifications: magnesium alloy, die-cast, gold-plated contacts, dead weight 6 g
Pioneer carbon fiber molded headshell. Simple and easy to use design. It is also attractive that it has a slightly lighter weight and is easy to combine. The exterior is dull (Fujisawa Yukishi)
Maintenance information: 2024.6.15 continuity confirmed
Accessories: No accessories
Main specifications: carbon fiber molding dead weight 9.5 g
It is a grace shell characterized by a fin shape. Lightweight yet hard, highly rigid shell (Asaine Tomoho)
Maintenance information: 2024.6.2 continuity confirmed
Accessories: No accessories
Main specifications: carbon fiber dead weight 10.7g
This is a specially designed product in which the company's original neighboring bronze machined pin terminals are set on the HS-1A using African ebony wood, and 6N copper wire with excellent sound quality is used as the shell lead. Since lead wires are soldered to the terminals on the arm side, sound quality improvement effects can also be expected due to a reduction in electrical contacts (Murakoshi Yoichi)
Maintenance information: 2024.6.11 continuity confirmed
Accessories: mounting screws
Main specifications: African ebony wood (eco-paint buff finish), brass finger tips (non-magnetic gold plated finish), own weight 10.2 g
An upper and lower pin structure is used to make the pressure at the contact point uniform. Contact surface stabilization is achieved with a spherical washer. High rigidity is maintained by completely machined super duralumin and manufactured in an integrated manner up to the finger holder (Asae Satoshi Method)
Maintenance information: 2024.6.14 continuity confirmed
Accessories: none
Main specifications: Super duralumin fully integrated machined body, black nickel plating, weight 10.5 g (lead wire not included), 11.0 g (lead wire included)
FR heavyweight headshell In combination with a heavy needle and pressure needle, it exhibits excellent tracing performance, such as digging up from deep inside a groove on a record board (Sasaki Shota)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: none
Main specifications: aluminum press processing actual measurement 19g
FR heavyweight headshell In combination with a heavy needle and pressure needle, it exhibits excellent tracing performance, such as digging up from deep inside a groove on a record board (Sasaki Shota)
Maintenance information: 2024.6.13 continuity confirmed
Accessories: none
Main specifications: aluminum press processing actual measurement 19g
Machined aluminum headshell made by ENTRE. It has a standard shape, and the sound stretches and tightens well. ※The lead wire is not original. (FUJISAWA KOSHI)
Maintenance information: 2024.6.15 continuity confirmed
Accessories: No accessories
Main specifications: dead weight approx. 13g
Machined aluminum headshell made by ENTRE. It has a standard shape, and the sound stretches and tightens well (Tomoho Asae)
Maintenance information: 2024.6.1 continuity confirmed
Accessories: none
Main specifications: dead weight approx. 13g
Machined aluminum headshell made by ENTRE. It has a standard shape, and the sound stretches and tightens well (Tomoho Asae)
Maintenance information: 2024.6.1 continuity confirmed
Accessories: none
Main specifications: dead weight approx. 13g
Machined aluminum headshell made by ENTRE. It has a standard shape, and the sound stretches and tightens well. ※The lead wire is not original. (FUJISAWA KOSHI)
Maintenance information: 2024.6.10 continuity confirmed
Accessories: none
Main specifications: dead weight approx. 13g
Comes with original box! JICO's original headshell. A stylish design reminiscent of an SME. Recommended for light needle pressure tone arms. (FUJISAWA KOSHI)
Maintenance information: 2024.6.2 continuity confirmed
Accessories: instruction manual, original box
Main specifications: aluminum stamping dead weight 7.3 g
Based on the CS-1000, it is a model that promotes high sound quality and weight reduction. The duralumin machined body and Diamond Like Carbon treatment achieve both a sense of luxury and rigidity (Daiki Goto)
Maintenance information: 2024.6.5 continuity confirmed
Accessories: original box, instruction manual, screws
Main specifications: dead weight 13.7 g
This classic headshell is made of magnesium alloy and has an attractive, unobtrusive sound. Overhang and left/right tilt adjustment are possible (Oikawa Tetsuji)
Accessories: none
Main specifications: dead weight 10g
This is a classic jewel tone (made in Nagoya) shell. There is slight dullness and mounting scratches on the body, but overall it is in good condition. ※The lead wire is not original. (FUJISAWA KOSHI)
Maintenance information: 2024.6.10 continuity confirmed
Accessories: none
Main specifications: machined aluminum block with a dead weight of 12g