Everything from the motor power supply to the tone arm has been fully maintained! New dust cover created! A player with a long-arm Ortofon AS-309S mounted on a TD-127. It comes with a dedicated optional weight, so you can use heavyweight cartridges such as SPUs. It has a high ability as a system, and it is a player that can play vividly regardless of genre, from classical to rock ※ The lifter works electrically, but since there is no sensor on the tone arm, auto stop or auto lift up is not possible (Oikawa Tetsuji)
Maintenance information: 2024.5.22 Maintained (deteriorated parts on the board, semi-fixed VOL for rotation speed adjustment, semi-fixed VOL replacement for sensor sensitivity adjustment. Front panel pitch adjustment VOL disassembly/contact polishing. Resolder the board. Disassemble and clean the arm. Drive belt replacement. Indicator lamp replacement. Grease up the platter bearing. Lubricate the motor shaft and disassemble and clean the clutch part. Floating, turntable rotation speed check, arm needle pressure check. Check the sound output. Chassis cleaning. (Comprehensive operation confirmation inspection)
Accessories: copy of instruction manual, optional weight
Main specifications: belt drive floating suspension 33/45/78rpm turntable 30cm zinc alloy 3.2kg double 16-pole synchronous motor speed fine adjustment range ± 6% W555 × H200 × D460 mm 20.4 kg
Elliptical type with built-in boost transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. Serial 830693 (Murakoshi Yoichi)
Maintenance information: 2024.6.11 sound output confirmed
Accessories: original box, needle cover, brush
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
*Needle cover missing. Elliptical type with built-in boost transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior has small scratches, dullness, and a feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.5.17 sound output confirmed
Accessories: none
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
※The cantilever is slightly to the right. This is the GE successor to the MC cartridge masterpiece SPU. This is an ambitious work that aims to expand the high range by using silver wire as the power generation coil. It is a GOLD version where you can enjoy attractive sound quality, with a delicate feeling added to the conventional wild tone. The needle cover is missing, rust floats on the G-shell terminal surface, and there is rust on the cantilever (Murakoshi Yoichi)
Maintenance information: 2024.6.14 sound output confirmed
Accessories: none
Main specifications: MC type elliptical needle output voltage 0.2 mV playback frequency band 20 to 20,000 Hz load resistance 10 ohms or more impedance 3 ohms needle pressure 3.0 to 4.5 g dead weight 32 g
*Needle cover missing. G-shell elliptical needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal cartridge that fully conveys the appeal of analog. There are slight corrosion irregularities on the shell (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
The 1.2m pair of unprocessed speaker cable has excellent balance from low to high frequencies, and has an energetic and warm tone. There are threads and disappearing characters on the exterior (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: No accessories
Case included. Higher-OFC is coated with high-purity silver for the 1.5m conductor of the power cable, and rhodium plating is used for the plug. The center of gravity changes to a thicker sound quality with a lower center of gravity. The exterior is a beautiful item with no feeling of use. (Yamato Yuki)
Maintenance information: 2024.6.15 continuity confirmed
Accessories: case
Case included. Higher-OFC is coated with high-purity silver for the 1.5m conductor of the power cable, and rhodium plating is used for the plug. The center of gravity changes to a thicker sound quality with a lower center of gravity. The exterior is a beautiful item with no feeling of use. (Yamato Yuki)
Maintenance information: 2024.6.15 continuity confirmed
Accessories: case
The 1.5m conductor of the power cable is coated with high-purity silver on Higher-OFC, and the plug is rhodium plated. The center of gravity changes to a thicker sound quality with a lower center of gravity (Murakoshi Yoichi)
Maintenance information: 2024.6.2 continuity confirmed
Accessories: none
Hi-Fi is in stock for the first time! GLANTZ statically balanced tone arm. The main body is machined from hard stainless steel, and the structure is firmly supported by 4 large bearings, and it has high traceability performance with reduced resonance and blurring, and exudes a sharp sound. Since there is weight in the weight part, you can use heavy cartridges such as OrtoFon's SPU without lowering the weight too much. The exterior is generally good (Takahashi Nobuyuki)
Maintenance information: 2024.6.2 operation confirmed
Accessories: instruction manual, headshell, phono cable, cartridge installation screw wrench
Main specifications: Form Static balance system Total length 330 mm Effective length (arm fulcrum to needle tip) 305 mm Effective length (arm fulcrum to center of turntable) 290 mm Compatible cartridge 16 to 43 g weight 1.14 kg Overhang 15 mm Mounting base internal dimensions 16 mm Mounting hole 30 mm
※Since the cantilever is large and tilts to the right, it is inexpensive. Needle cover missing. The MC30S (MC30 Supreme), the upper model of the MC20S (MC30 Supreme) has a high output of 0.5 mV, which not only has a sense of dynamism and power, but is also characterized by a delicate and elegant high frequency. In classical music such as jazz and rock, there is a sense of depth in the performance, and it stretches well, and you can feel the luster of stringed instruments. There is a feeling of use on the exterior, such as dullness and scratches on the body (Murakoshi Yoichi)
Maintenance information: 2024.5.2 sound output
Accessories: case
Main specifications: MC type output 0.5 mV internal impedance 5 ohms needle pressure 1.8 g to 2.2 g dead weight 10.7 g
The price has been reduced! 2024/5/25 sales price 89,800 yen Maintained! CG25D is a staple mono needle and is the highest peak. The precise, thick, and thick sound brings out a unique sense of density that is different from stereo needles. The exterior is dull all over, and paint peeling can be seen on the body. Serial 137743 (Yonejima Satoshi)
Maintenance information: 2024.5.25 Maintained (damper replaced)
Accessories: No accessories
Main specifications: mono round needle, MC type, output voltage: 1.5 mV, proper needle pressure: 3.5 g, dead weight: 32 g
Speaker cable uses 0.9 m pair Y lug end - untreated 7N copper Excellent separation and an overwhelmingly high S/N ratio. The simplicity of the sound, the good localization, the texture of the strings, and the texture of the voice are amazing. There is friction and dirt on the sheath (Kojima Yosuke)
Accessories: none
Speaker cable uses 0.9 m pair Y lug end - untreated 7N copper Excellent separation and an overwhelmingly high S/N ratio. The simplicity of the sound, the good localization, the texture of the strings, and the texture of the voice are amazing. There is friction and dirt on the sheath (Kojima Yosuke)
Accessories: none
The price has been reduced. 2024/2/2 sales price 2,500 yen. ※Inexpensive because 1 bottle is out of stock. Orthophone speaker terminal joint cable Be sure to improve the sound quality of speakers compatible with bi-wiring with 7N ultra-high purity copper wire. One vinyl cover is short (Takasaki Atsushi)
Accessories: original box
Main specifications: 7N copper (diameter 1mm) +gold plating treatment approx. 150mm/book
※1 bottle only. The RCA cable uses a 0.6 m 6N-7N hybrid conductor and twin core structure. The cable is thick and powerful in the mid-range, making it a great cable for vintage audio. There is slight dullness on the plug part (Murakoshi Yoichi)
Maintenance information: 2023.7.20 Continuity confirmed
Accessories: none
Orthophone 95th anniversary special limited set with shell An aluminum headshell SH-4 special limited-edition color red type is attached to the popular 2M Red MM cartridge. This is a high cost performance entry model MM cartridge that is clear, has good sound separation, and fits well with modern sources. *Since there is a crack on the needle cover side, it cannot be fixed to the main body. (MURAKOSHI Yoichi)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: instruction manual, original box, needle cover (broken claws), brush, screws, shell
Main specifications: [2M RED] MM type 5.5 mV 20 to 22,000 Hz 47 ohms suitable needle pressure 1.8 g dead weight 7.2 g [SH4R] gold plated terminal body material aluminum self weight 9.3 g (excluding mounting screws)