Sound Studio Z concept = this is a super tweeter that includes a network and adds an ultra-high frequency range. Therefore, there is no need for a network of basic capacitors, etc., and you can use it immediately by simply connecting it in parallel with the speaker you are currently using (Ryo Mizusaki)
Maintenance information: 2024.6.15 sound output confirmed
Accessories: instruction manual, condenser
Main specifications: W63 x H63 x D81 mm
Replacement needle compatible with National EPS-19ST Operation has not been confirmed since there is no main unit (Hiura Katsuji)
Maintenance Information: Operation Unconfirmed
Accessories: original box
The price has been reduced! 2023/10/7 This is a self-made MC step-up transformer with a sales price of 20,000 yen. According to the specifications, the boost ratio appears to be 1:10. Use it with high output cartridges such as the DL-103! (FUJISAWA KOSHI)
Maintenance information: 2023.10.7 operation confirmed
Accessories: none
Main specifications: MC boost transformer input/output 1 system boost ratio 1:10 W 110 x H45 x D145 mm (actual measurement)
The price has been drastically reduced. 2024/6/5 sales price 348,000 yen Maintained! This is a very well made 300B single amp. The outstanding sharpness and power, and sweet and gorgeous sound are unbearable. The JJ 300B is used as the output tube. It is a combination of the popular transformer TAMURA F-2007 pair, PC-3004, and A-4003. The first stage uses 12AT7, and the rectifier tube uses 5AR4. It comes with a volume and can be connected directly to a CD. There is a ham balancer inside (Yasuhito Koshihama)
Maintenance information: 2024.6.5 maintained (AC cord missing added; wiring changed to output impedance 4Ω → 8Ω; main volume 100K B curve → 2 replacement; vacuum tube 12AT7 deterioration replacement; RCA jack and vacuum tube socket caulking repair. Operation checked with AC 100V (measured with rated output 10W+10W SP8Ω)
Accessories: power cable
Main specifications: output 10W+10W (actual measurement) W434 × H217 × D333 mm 18.9 Kg (actual measurement)
Currently sold. This is a self-made 10cm full-range 1-way speaker with unknown details. There is no problem with the sweep or music signal, but the current situation is because it is cheap. There are bond marks on the exterior and center cap, and a feeling of use can be seen, such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.3 sound output confirmed
Accessories: none
Main specifications: W120 x H200 x D122 mm 2.5 kg (actual measurement)
TRIO N-39 compatible needle. This is a replacement needle for TRIO V-39. Operation not confirmed (Murakoshi Yoichi)
Maintenance information: operation unconfirmed
Accessories: original box
The price has been reduced! 2024/6/11 sales price 69,800 yen ※Currently sold. Aiwa's DSD DAC. A/D converter and D/A converter set. It is possible to reproduce DSD 1-bit 64fs signals in SACD format. Even with analog input from compressed sound sources such as MP3s, the sense of localization, sound field, and luster of sound are improved. Serial D101211111 WD01210911 (Tomonori Asaine)
Maintenance information: 2024.6.9 operation confirmed
Accessories: power adapter, HMDI connection cable, instruction manual
Main specifications: AX-D1: DSD1 bit/64 fs playback frequency band 20 Hz to 100 kHz (+0/-3 dB) dynamic range 102 dB or more, SNR ratio 102 dB or more at 1 kHz, 107 dB or more at 20 kHz channel separation 100 dB or more size W250 x D170 x H50 mm weight 1.5 kg AX-WD: LPCM192 kHz/24 bit/128 fs DSD1 bit/ 64fs (DSD64 mode, 2.8224MHz) size W250 x D170 x H50 mm weight 1.6 kg
This is a specially designed product in which the company's original neighboring bronze machined pin terminals are set on the HS-1A using African ebony wood, and 6N copper wire with excellent sound quality is used as the shell lead. Since lead wires are soldered to the terminals on the arm side, sound quality improvement effects can also be expected due to a reduction in electrical contacts (Murakoshi Yoichi)
Maintenance information: 2024.6.11 continuity confirmed
Accessories: mounting screws
Main specifications: African ebony wood (eco-paint buff finish), brass finger tips (non-magnetic gold plated finish), own weight 10.2 g
This is a replacement needle for Hitachi. Compatible with MFS-250. Unopened Operation has not been checked (Hiura Katsuji)
Maintenance Information: Operation Unconfirmed
Accessories: original box
This is a replacement needle compatible with Hitachi MFS-250. Unopened Operation has not been checked (Hiura Katsuji)
Maintenance Information: Operation Unconfirmed
Accessories: original box
The price has been reduced! 2024/2/8 sales price 1,000 yen Compatible replacement needle for AUREX MM cartridge C-550/2. The standard needle is a carbon fiber cantilever, which is presumably made of metal. Sound was made using C-550/2 (Takahashi Nobuyuki)
Maintenance information: 2024.2.8 operation confirmed (sound output on C-550/2)
Accessories: none
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.17 Conductivity confirmed
Accessories: none
Disposal prices have been reduced. Member discounts are not applicable. 2018/10/24 Sales price 3,000 yen These are parts made in Mexico whose details are unknown. There is rust, dirt, etc. (NAGAI Michio)
Maintenance Information: 2018.10.24 Conductivity Confirmed
Accessories: none
Unspecified power cable 2.0m. The plug is Panasonic WF5018K, and the connector is made by Global Electronics. This cable is relatively easy to handle. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.5.5 continuity confirmed
Accessories: none
manufacturer unknown. It seems to be a compatible needle for portable players whose details are unknown (Hiura Katsugu)
Maintenance information: operation unconfirmed
Accessories: none
The price has been reduced! 2024/2/8 sales price 1,000 yen Compatible replacement needle for AUREX MM cartridge C-550/2. The standard needle is a carbon fiber cantilever, which is presumably made of metal. Sound was made using C-550/2 (Takahashi Nobuyuki)
Maintenance information: 2024.2.8 operation confirmed (sound output on C-550/2)
Accessories: none
An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
Unspecified XLR (male) to RCA (female) conversion plug only. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.8.14 Confirmation confirmed
Accessories: none
Main specifications: No. 2 HOT
XLR female to mono mini jack cable 4.5m unusual combination microphone cable. Can also be used as a normal microphone cable using standard jack conversion (Murakoshi Yoichi)
Maintenance information: 2024.4.11 continuity confirmed
Accessories: none
The price has been reduced. 2024/1/5 sales price 400 yen. ※1 bottle only. 3 cm unit with unknown details. Since the size and condenser is attached to the plus side, it seems to be a tweeter. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2022.11.15 Operation confirmed
Accessories: none
Main specifications: actual impedance measurement 3 ohms 3 cm
XLR cable 5.0 m male to female details unknown. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.9 continuity confirmed
Accessories: none
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer The terminal is male and cannot be used as a microphone. There are a few indelible writing marks left on the plug (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
XLR cable 1.5m pair interconnect cable with unknown details The plug is made by Neutrik (Tomoho Asaine)
Maintenance information: 2024.6.18 continuity confirmed
Accessories: none
※1 piece only (male to male) XLR cable 1.5 m interconnect cable with unknown manufacturer. There is a feeling of use, and there are a few indelible writing marks left (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
The Sennheiser headphone cable (can be used with HD580, HD600, and HD650) uses silver wire for the wire, and the sound is smooth and supple (Tamura Eiji)
Maintenance information: 2024.6.18 continuity confirmed
Accessories: original box
Power cable, 0.4 m, no terminals, 6nCu+OFC new hybrid 2-core conductor Although it is the company's entry model, it is a power cable with low noise, stable sound, and high C/P (Kanai Hidetsugu)
Maintenance information: 2023.12.9 Continuity confirmed
Accessories: none
Only 1 speaker cable uses a new conductor that is a hybrid of 4 types of materials, including the innovative HiFC and PCUHD wire materials, with an exquisite golden ratio, centering on an untreated ultra-high purity 6NCU at the end of the 1.35 m end. It's a clear high range, a plump middle range, and a heavy low range. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.5 continuity confirmed
Accessories: none
Only 1 speaker cable uses a new conductor by hybridizing 4 types of materials, including the innovative HiFC and PCUHD wire materials, with an exquisite golden ratio, centering on an untreated ultra-high purity 6NCU at the end. It's a clear high range, a plump middle range, and a heavy low range. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.5 continuity confirmed
Accessories: none
※There is no problem with operation, but it is currently sold because it is cheap. A subwoofer that can also be installed in a home theater or for those with insufficient bass in the system. The settings are simple, and you can create sound according to the speaker and room conditions. There are scratches, dirt, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.3.3 operation confirmed
Accessories: none
Main specifications: 1 way, 1 speaker, advanced YST system, floor type, anti-magnetic high-cut filter, 50-150 Hz, continuously variable dimensions, W235 x H485 x D409 mm, weight 14 kg
Internal and external maintenance has been applied and brushed up. The vivid sense of dynamism and the sharpness of the high frequencies typical of YAMAHA have been revived. It has a low frequency thickness that 1000 monitors don't have. It is a timeless masterpiece with a clear sense of transparency, upper and lower driving force, and the smooth connection, and the heavy exterior with an ebony finish that stands out at a glance even today. It is in good condition due to maintenance. Serial 11478L 11478R (Yamato Yuki)
Maintenance information: 2024.4.1 operation confirmed
2023.9.4 Maintained (exterior repair/polishing/clear finish. Rear baffle repair/painting. Saran net replacement. Unit frame painting. Network maintenance (Since the terminals have already been replaced with external products, adjust the direction and tighten, apply a screw fastener, and replace the mounting screws. ATT contact status check (check that there are no gaps). A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Input/output waveform and balance check, sound output check) Unit detachable)
Accessories: saran net
Main specifications: 3-way sealed playback frequency band 40Hz to 20kH sound pressure level 90dB rated input 50W maximum allowable input 100W impedance 8Ω crossover frequency 500Hz/6kHz dimensions W395 x H710 x D349 mm 39 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/16 sales price 9,800 yen*Currently sold, it is cheap because it is in poor condition. This model has a nicely looking model with units arranged in the center. It has excellent sharpness from low to high frequencies, and is perfect for those who listen to pop music. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 105025A 105025B (Hiroki Aso)
Maintenance information: 2024.5.16 sound output confirmed (good sweep test)
Accessories: saran net
Main specifications: low frequency 18 cm cone woofer high range 3.5 cm dome tweeter impedance 6 ohm allowable input 70W W225 x H370 x D229 mm 5.4 kg/book
Speaker with active servo technology A powered speaker with a built-in power amplifier in the woofer (only the woofer part requires a power source to drive). The medium and high frequencies, which are typical of Yamaha, remain the same, and the low frequencies also come out well. It has a good balance and can be used regardless of genre (Daiki Goto)
Maintenance information: 2024.5.9 operation confirmed
Accessories: instruction manual
Main specifications: 4 way, 3 speakers, bookshelf type, W340 x H700 x D337 mm, 30 kg/1
Genuine YAMAHA, genuine replacement needle for CG-8100 Operation has not been checked (Murakoshi Yoichi)
Maintenance information: operation unconfirmed
Accessories: original box
The price has been drastically reduced! Yamaha's top CD/SACD player at the 2024/6/17 sales price of 298,000 yen. The D/A section is equipped with ESS Technology's new-generation 32-bit converter, SABRE (Sabre) 32 Reference DAC (ES9018). High quality design with fully balanced transmission at all stages, thorough low impedance, and high rigidity and low resonance construction. It is a model aimed at natural reproduction that reaches straight to the heart of the listener like an instrument. The lettering on the open/close button has become thinner. Serial Y022203WX (Fujisawa Yukishi)
Maintenance information: 2024.6.17 Operation confirmed
Accessories: power cord (non-genuine), remote control, spike base
Main specifications: CD/SACD player playable disc CD/SACD/CD-R/CD-RW frequency characteristics 2 Hz to 20 kHz (CD) 2 Hz to 50 kHz (SACD) W435 x H142 x D440 mm 19.2 kg
*Currently sold. YAMAHA bookshelf speakers. It is a high-resolution compatible model created by the designer of the “Soavo” series, which was highly acclaimed worldwide, and although it is an entry model, it is designed with particular attention to sound. Of course, the traditional high frequencies of the NS Series are excellent, and the fact that bass reflex dubbing, which is common on bookshelves, is suppressed is a good impression. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.6.16 Operation confirmed
Accessories: saran net, original box
Main specifications: 2-way bass reflex type (non-magnetic) playback frequency band 55 Hz to 45 kHz impedance 6 ohms allowable input 40 W maximum input 120 W output sound pressure level 87 dB crossover frequency 2.8 kHz W183 x H320 x D267 mm weight 6.1 kg
*Currently sold. A Yamaha center speaker with high cost performance. The full range is used for the woofer, contributing to improving the quality of the mid-range range. You can see the exterior, mold, dullness, abrasions, etc. and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.6.4 operation confirmed
Accessories: saran net
Main specifications: woofer 12cm cone tweeter 2.5cm soft dome type anti-magnetic impedance 6Ω allowable input 60W W465 x H150 x D185 mm 4.7 kg
Yamaha's new compact stereo CC-75 series speakers. Equipped with Yamaha active servo technology that reproduces rich deep bass even though it is small. The exterior has a feeling of use such as dullness and small scratches. Serial 646497Y0 646507Y0 (Takahashi Nobuyuki)
Maintenance information: 2024.6.3 operation confirmed
Accessories: saran net
Main specifications: 14cm woofer, 5cm tweeter, 1.1 cm super tweeter impedance 6 ohms, playback frequency band 40 Hz to 20,000 Hz, W200 x H330 x D239 mm, 4.3 kg
*Currently sold. A Yamaha center speaker with high cost performance. The full range is used for the woofer, contributing to improving the quality of the mid-range range. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.4 operation confirmed
Accessories: saran net
Main specifications: woofer 12cm cone tweeter 2.5cm soft dome type anti-magnetic impedance 6Ω allowable input 60W W465 x H150 x D185 mm 4.7 kg
A floor-type speaker with an authentic 3-way configuration with all-round appeal, from pure audio to theaters. The wide range playback has a sense of volume, and there is an exhilarating feeling that you can drop out the mids and highs that are particularly calm and easy to hear. There is a crack in part of the plastic that covers the magnet on the saran net (Sasaki Shota)
Maintenance information: 2024.6.13 operation confirmed
Accessories: jumper plate
Main specifications: 3-way bass reflex type (non-magnetic) playback frequency band 45 Hz to 50 kHz impedance 6 ohms sound pressure level 89 dB W354 x H1,012 x D374 mm weight 25.0 kg
Disposal prices have been reduced. Member discounts will not be applied. 2023/1/23 sales price 500 yen. Sale as is. 1 YAMAHA full range unit. There is a dent in the center cap, and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.1.23 Operation confirmed
Accessories: none
Main specifications: Outer diameter approx. 205 mm, screw pitch approx. 105 mm, weight 1.5 kg
※Since it is cheap, it is currently sold. This is a thin center speaker. Since it has an anti-magnetic design, this model is easy to use and easy to combine with other speakers. Recommended for those who are building surround sound for the first time. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.1 sound output confirmed
Accessories: instruction manual, connection cord, original box
Main specifications: 2 way, 3 speakers, bass reflex system, center type, anti-magnetic design, playback frequency band 60 Hz to 20 kHz, 88 dB, 6 ohms, allowable input, 40 W, W435 x H100 x D221 mm, 2.2 kg
The price has been reduced. 2024/5/7 sales price 29,800 yen This item is currently sold because dirt, tobacco smell, and feeling of use are conspicuous. An HX series higher-level machine that effectively controls space. It's a speaker for home theaters, but the sharp sound is attractive (Daiki Goto)
Maintenance information: 2024.5.7 operation confirmed
Accessories: none
Main specifications: 3-way bass reflex type (anti-magnetic) 20cm cone woofer x 2, 13cm cone midrange, 3cm dome tweeter 6Ω 364 x 1102 x 397 mm 32.5 kg
There is no problem with the operation, but it will be handed over as is. Yamaha subwoofer. You can easily enjoy powerful sound. The high-cut filter allows you to listen in the desired range, so the range of uses also expands. The exterior has a slightly raised part on the top plate, and there is a scratch on the back corner (Mizusaki Ryo)
Maintenance information: 2024.5.9 sound output confirmed
Accessories: none
Main specifications: A-YST method anti-magnetic amplifier output 250W playback frequency band 20Hz to 160Hz high-cut filter frequency 40Hz to 140Hz continuously variable W340 x H432 x D370 mm 17 kg
*The attenuator is cheap and is sold as is. This model was measured to improve the quality of the NS-500M. Carbon is used for the woofer. It has a transparent tone typical of Yamaha, has good response, and is made with digital sources in mind. Overall, there is a lot of feeling of use such as small scratches and dullness (Murakoshi Yoichi)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: saran net
Main specifications: 3-way speaker 40Hz-20000Hz 6Ω 100W W374 x H678 x D324.5mm 23.5 kg
1.5 m pair of balanced cables ULTRA series OFHC, a unique cable with a natural, smooth tone and a high sense of sound pressure. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.6.12 continuity confirmed
Accessories: No accessories
Mid-size model of 1.0 m XLO digital XLR cable. A unique cable that is smooth and has a high texture in the mid to high range, yet also has a high sense of sound pressure. The exterior is dull (Yonejima Satoshi)
Maintenance information: 2024.6.12 continuity confirmed
Accessories: No accessories
A standard wire world model with a wide 1.5m pair range and a smooth RCA cable. It allows you to enjoy music in the glossy, colorful mid- to high-frequency range. The exterior is dull and slightly sticky (Satoshi Yonejima)
Maintenance information: 2024.6.12 continuity confirmed
Accessories: No accessories
※Since it is an old standard, it is inexpensive. HDMI cable 3.0 m gold plate coated terminal uses a flat structure to avoid signal loss, crosstalk, and timing errors caused by uneven length when bent (Murakoshi Yoichi)
Maintenance information: 2024.5.10 sound output confirmed
Accessories: none
A wireworld RCA cable that uses OFC copper as the 1.0 m pair conductor of the RCA cable, perfect for a basic model. It is a cable with the feel of a wire world, with thickness in the mid range and glamor in the high range. As for the exterior, there is a screw on the plug (Satoshi Yonejima)
Maintenance information: 2024.6.12 continuity confirmed
Accessories: No accessories
The 2.0m optical digital cable is probably a model that has not been sold in Japan. There is a slight stickiness on the sheath (Tamura Eiji)
Maintenance information: 2024.6.13 operation confirmed
Accessories: case