Stylish cartridge with white and yellow coloring. It's a nice, sharp sound. The exterior is in a state where there is a feeling of use such as oxidation and dullness over time (Yamato Yuki)
Maintenance information: 2026.4.11 sound output confirmed
Accessories: none
Main specifications: VM type needle pressure 1-2 g dead weight 17 g
It is equipped with a large aperture driver with a wide dynamic range, injecting the design theory of higher-level models that achieve both strength and suppleness of sound. It uses a “CCAW bobbin-wound voice coil,” which enables delicate and bold expression, and a top-mount PCB system that uniformizes air flow and brings out accurate diaphragm movement without distortion. By linking each of the selected acoustic parts, an accurate sound with little transmission loss is depicted (Murakoshi Yoichi)
Maintenance information: 2026.4.28 sound output confirmed
Accessories: original box, warranty card, instruction manual
Main specifications: Driver φ53mm output sound pressure level 100dB/mW playback frequency band 5 to 34,000 Hz maximum input 1,000 mW impedance 40Ω mass (excluding cord) 300g plug φ6.3 mm standard/φ3.5 mm mini gold-plated stereo 2-way cord 3.0 m (single out)
The rubber grip makes it easy to insert and remove the square optical terminal of an optical digital cable, and also has an anti-vibration effect. A sturdy metal plug is used, and an APF is used that is easy to use. There is a feeling of use (Murakoshi Yoichi)
Maintenance information: 2026.4.25 continuity confirmed
Accessories: none
※The cartridge cannot be attached because the finger holder is missing. Lightweight cartridge shell that was standard equipment on the AT-1009. Highly rigid 2-piece construction This is a convenient shell that makes it easy to adjust the overhang. If you already use a shell of the same model, how about stocking it? (FUJISAWA KOSHI)
Maintenance information: 2026.4.28 continuity confirmed
Accessories: No accessories
Key Specifications: Impact molded lightweight shell, dead weight 9g
Unused item. Stereo mini plug to RCA cable, 1.0 m, I have the impression that it has stable sound quality and can be used with peace of mind. (FUJISAWA KOSHI)
Accessories: original box
Uses a 1.0 m pair of RCA cables PCOCC and OFC hybrid conductors. Contains titanium that is resistant to external disturbances. There is a feeling of use and threads on the exterior of the sheath and terminals (Tomoho Asaine)
Maintenance information: 2026.4.17 continuity confirmed
Accessories: none
※Cleaning liquid is not included. A record cleaner that uses directional velvet, which has a high cleaning effect. Follow the direction of the arrow that appears and wipe the record. A special sponge structure keeps moisture by putting cleaning liquid into the handle. The velvet surface is wide and easy to use. The exterior has an overall feeling of use such as dullness (Mizusaki Ryo)
Accessories: none
A long-selling Technica disc stabilizer model. Moderate weight does not put a burden on the motor (Daiki Goto)
Accessories: none
Main specifications: diameter 80 mm height 35 mm dead weight approx. 600 g
*Currently sold. High sound quality phono equalizer compatible with MM/MC cartridges. Utilizing the analog audio knowledge and experience that the company has cultivated over many years, this product combines high-quality parts to achieve low noise and minimal distortion in an optimal layout according to acoustic characteristics. There is a small wound (Sasaki Shota)
Maintenance information: 2026.4.21 operation confirmed
Accessories: original box, manual, power adapter
Main specifications: input impedance mm47kΩ MC120Ω input sensitivity mm4.5mV MC0.28mV rated output 250mV gain mm35dB MC59dB SNR mm100dB MC74dB RIAA deviation (20-20kHz) ±0.5dB power consumption 2.5W dimensions W197.5 x H47 x D125.5 mm mass approx. 890 g
This is a mono LP exclusive model with a round needle bonded to the mono exclusive body. Record surface noise is reduced, and stable mono playback sound can be heard. Both stylus and cantilever are good. There is no inner box, but only the outer box is included (Sasaki Shota)
Maintenance Information: 2026.4.21 Sound output works well
Accessories: manual, outer box
Main specifications: VM type playback frequency range 20 to 20,000 Hz output voltage 3.0 mV needle pressure 1.8 to 2.2 g (2.0 g standard) stylus joint round needle (0.6 mil) cantilever aluminum pipe external dimensions H17.3 x W17.0 x D28.2 mm mass 6.4 g
Set of 8 Technica hybrid insulators. Special anti-vibration rubber on the top and bottom “Honeynight” uses machined brass as the base material to effectively suppress unnecessary vibrations. The safety design prevents slipping even on light devices. The exterior is dull and oxidized over time, the color fades on the label, and the anti-vibration rubber deteriorates (Asae Satoshi Law)
Accessories: none
Main specifications: 3-layer hybrid structure (hannenite/brass/honeyite) diameter 20 x 11 mm, mass approx. 25 g (per piece), load capacity 5 kg (per piece)
The flat characteristics make the sound good and are delicate. The sound quality is relatively thick among Audio-Technica models, and I like it without losing too much weight. There is dullness and a feeling of use (Murakoshi Yoichi)
Maintenance information: 2026.4.17 sound output confirmed
Accessories: none
Main specifications: mm type output voltage 4 mV needle pressure 0.75 to 1.75 g oval needle self weight 9 g
Dry record cleaner made with premium velvet. The shape is easy to hold, and records can be cleaned effectively. There is a slight feeling of use, but it is in good condition (Tomoho Asae)
Accessories: none
This model uses a solid elliptical needle with reduced effective mass of the vibration system and realizes broadband playback. It is a high cost performance cartridge that satisfies both beginners and enthusiasts with high resolution and wide range (Oikawa Tetsuji)
Maintenance information: 2026.4.18 Operation confirmed
Accessories: original box
Main specifications: VM type playback frequency range 20 to 25,000 Hz output voltage 4.5 mV (1 kHz, 5 cm/sec.) needle pressure 1.8 to 2.2 g (2.0 g standard) mass 6.4 g
As can be seen from its fearless design, it is a headshell with precise and tight sound. There is a slight feeling of use such as dullness (Murakoshi Yoichi)
Maintenance information: 2026.4.17 continuity confirmed
Accessories: none
Main specifications: Technihard dead weight 16g
This headshell is a combination of magnesium alloy and anti-vibration material. The overhang and left/right tilt can be adjusted. The exterior is dull (Murakoshi Yoichi)
Maintenance information: 2026.4.17 continuity confirmed
Accessories: none
Main specifications: magnesium alloy dead weight 10.2 g
As can be seen from its fearless design, it is a headshell with precise and tight sound. There is a slight feeling of use such as dullness (Murakoshi Yoichi)
Maintenance information: 2026.4.17 continuity confirmed
Accessories: none
Main specifications: Technihard dead weight 16g
A classic disc stabilizer. The moderate weight gives a sense of stability for playing records. There is color fading due to sunburn (Tomoho Asaine)
Accessories: none
Main specifications: diameter 80 mm height 35 mm dead weight approx. 600 g
The speaker cable is a basic model that uses an unprocessed OFC conductor for 1.4 m pair terminals, and features straightforward sound quality with few habits. There is friction, dullness etc. on the sheath (Tomoho Asaine)
Maintenance information: 2026.4.11 continuity confirmed
A new dust cover was created, and the main unit was thoroughly maintained, such as replacing 12 electrolytic capacitors! Furthermore, it comes with a shell cartridge (M44G/ MG-10), so you can use it right away! This model won the Good Design Award in 1976. It is a famous machine from yesteryear, full of 70s character. It has a stable sound and is recommended as an introduction to analog. As for the exterior, small scratches, dullness, and light burns can be seen over time. Serial 41033374 (Yamato Yuki)
Maintenance information: 2026.4.10 Maintained (capacitance loss capacitor replacement arm disassembly, inspection, cleaning speed VR cleaning, etc., inspection of various parts, operation tests carried out)
Accessories: Shell (audio-technica MG-10) cartridge (SHURE M44G) instruction manual copy
Main specifications: Direct drive AC servo motor, 60 dB SN-ratio turntable/diameter 31 cm, aluminum die-cast, power consumption 12.5 W, weight 9.1 kg
The price has been reduced. 2026/3/18 sales price 12,000 yen. Replacement needle for VM740ML I was able to confirm the sound output. If you were looking for one, please take this opportunity (Murakoshi Yoichi)
Maintenance information: 2026.3.18 sound output confirmed
Accessories: case
Main specifications: needle pressure 1.8 to 2.2 g (2.0 g standard)
Lightweight shell made by Audio-Technica. Perfect for sounding high compliance cartridges. You can see the exterior, dullness, and feeling of use (Matsumoto Tsuyoshi)
Maintenance information: 2026.4.6 continuity confirmed
Accessories: none
Main specifications: light alloy press processing dead weight 8.5 g
A classic headshell made of magnesium alloy with an attractive, unobtrusive sound. Overhang and left/right tilt adjustments are possible. The exterior has a feeling of use such as dullness (Matsumoto Tsuyoshi)
Maintenance information: 2026.4.5 continuity confirmed
Accessories: none
Main specifications: magnesium alloy dead weight 10g
Audio-Technica entry class VM cartridge. It has a bright and light sound that matches popular systems in general. Recommended for beginners (Matsumoto Tsuyoshi)
Maintenance information: 2026.4.5 sound output confirmed
Accessories: none
Main specifications: Playback frequency band 20 to 20,000 Hz, output voltage 5.0 mV, standard needle pressure 1.5 g, dead weight 3.5 g
A classic headshell made of magnesium alloy with an attractive, unobtrusive sound. Overhang and left/right tilt adjustments are possible. The exterior has a feeling of use such as dullness (Matsumoto Tsuyoshi)
Maintenance information: 2026.4.5 continuity confirmed
Accessories: none
Main specifications: magnesium alloy dead weight 10g
Along with the MG-10, this headshell is popular. The overhang can be adjusted and the model is easy to use. The exterior has a feeling of use such as dullness, small scratches, paint peeling, etc. (Takahashi Nobuyuki)
Accessories: none
Main specifications: dead weight 11g
Audio-Technica's classic shell. Uses die-cast aluminum. 3 levels of overhang adjustment are possible (Oikawa Tetsuji)
Accessories: screws
Main specifications: Die-cast aluminum, dead weight 13g
Audio-Technica's classic shell. Uses die-cast aluminum. 3 levels of overhang adjustment are possible (Oikawa Tetsuji)
Accessories: none
Main specifications: Die-cast aluminum, dead weight 13g