Maintained! A famous machine 44 with an easy-to-handle RCA terminal added to the rear terminal of the Quad control amplifier. The British QUAD's small preamp is a perfect balance between the freshness and richness of character. When paired with the same speakers made in England, you can enjoy a calm, high-quality sound. There are line scratches on the left side of the exterior, dull buttons, etc., and there is a feeling of use throughout (Kobayashi Hitoshi)
Maintenance Information: 2026.2.3 Maintained (IC OP AMP replacement in CD position board. Other checks) 2025.3.5 maintenance completed (power supply SW contact cleaning, correction, RCA terminal screw tightening correction, cleaning, caulking each SW, Vol cleaning (some chips remain) 2023.11.15 maintenance (VOL cleaning, C replacement in other mainboards, C etc. in each AMP, etc.) AC spark killer replacement in the power supply.)
Accessories: power cord, connection cord, instruction manual (copy)
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321 x H103 x D203 mm, 4 kg
The disposal price has been reduced! Member prices are not applicable. 2026/3/31 sales price 448,000 yen, 31 deteriorated parts, including capacitors, have been replaced and maintained! A teleo power amplifier with a traditional dual mono configuration. The overwhelming driving power and precise sound are attractive. You can enjoy the strong driving power that allows even a 38cm woofer to brake well, and the hot sound unique to Levinson of this era. Genuine Harman The exterior has dullness over time, small scratches, and bumps. Serial 1190 (Yonejima Satoshi)
Maintenance information: 2026.3.31 Maintained (replaced with deteriorated parts (23 capacitors, 8 resistors). There was deterioration in part of the solder, and it was fixed. Other inspections and adjustments))
Accessories: power cord, remo pin, balance short pin
Main specifications: stereo power amplifier, dual mono configuration, 200W+200W (8Ω), 800W (8Ω, when connected to a bridge), input impedance 50kΩ, W483 x H210 x D450mm, 40 kg
The price has been reduced. 2026/4/3 sales price 448,000 yen Manufacturer maintained! It is a model that faithfully reproduces the famous Model 7 that Marantz is proud of at the company's North Carolina plant. The glossy mid-high range, thick mid-range, and sharpness typical of the same model have been faithfully inherited. Inconspicuous (Daiki Goto)
Maintenance information: 2026.4.3 Marantz metropolitan area service maintained (lamp replacement. Each lever switch fixes poor contact. In addition, since part of the power supply unit composite block capacitor ran out of capacity, the capacitor was externally attached. On the rear, the RCA input/output terminal chassis ground floats, and all terminal ground wiring connections have been corrected. Each vacuum tube pin, clean.)
Accessories: power cable, copy of instruction manual
Main specifications: used ECC83/12AX7 6 vacuum tubes W391 x H155 x D261 mm 5 kg
The price has been drastically reduced. 2026/4/6 sales price 450,000 yen Maintenance was completed in 2023/7. A highly complete player system created by Audiocraft, which has been working on analog record playback with various approaches. It stood out with its floating structure, which was rare among domestic machines at the time, when there were many rigites. The belt drive, floating, and arm are equipped with the SME 3010R and are compatible with various cartridges, making it one car where you can clearly feel the advantages of analog. It is in good condition even when viewed from the model year (Oikawa Tetsuji)
Maintenance information: 2026.4.6 operation confirmed
2023.7.15 Maintained (Removed boards, etc. have been attached. Since there are no screw sleeves or anything else, I installed an additional one. The circuit connections have been rewired. The electrolytic capacitor has been replaced. (PU code created)
Accessories: none
Main specifications: belt drive player W500 x H240 x D400 mm (actual measurement) Arm part: short arm type: static balance type effective length: 237 mm cartridge mounting weight range: 1.5 to 26 g (cartridge only) 9.5 to 34 g (including shell) needle pressure variable range: 0 to 5 g
This product has completed maintenance such as replacing 28 deteriorated parts, including capacitors, and front panel dismantling, cleaning, and peeling correction! A power amplifier representing the Macintons of yesteryear. The power to make a 38cm woofer sound lightly with impressive driving power and a sense of scale with a rich sense of volume are impressive. It is a powerful machine that has high overall strength and is one of the most popular McKinns in history. The bright mid to high range sound goes well with modern speakers. As for the exterior, small scratches and dullness can be seen over time. *The upper part of the speaker terminal is painted white in several places. Serial JKE2626 (Yamato Yuki)
Maintenance information: 2026.4.9 maintained (panel dismantling, meter part, acrylic plate removal, cleaning, cleaning, repair, meter, regulator part C liquid leak replacement board cleaning, meter, illumination, display lamp replacement, power stage Tr single check, socket part soldering, resoldering each connector cleaning, interior and exterior cleaning)
Accessories: instruction manual power cable
Main specifications: rated output 500W+500W MONO 1,000W output frequency band 20Hz to 20kHz SNR 115dB (at rated output) W445 x H255 x D491 mm weight 49.9 kg
This is a line-only control amplifier. It's a sound that connoisseurs like because it has both the amount of information and thickness. Equipped with balanced input/output, both balanced input/output have individual polarity switches, so you can connect without worrying about polarity. There is some dullness on the exterior (Murakoshi Yoichi)
Maintenance information: 2026.4.4 sound output confirmed
Accessories: instruction manual (copy), power cable
Main specifications: balanced input: 2 system unbalanced input: 4 system tape input/output: 2 system balanced output: 1 system unbalanced output: 1 system W440xH95xD400mm 6.2 kg
A 0.9 m PSE standard eyeglass type 2-pin connector conductor uses a “semi-solid long grain copper (LGC)” as the conductor. The sharp sound quality unique to quests (Murakoshi Yoichi)
Maintenance information: 2026.4.7 continuity confirmed
Accessories: original box
An audiocraft headshell that uses a perfect lock pin in addition to its sturdy construction with a hard aluminum molding. It has a degree of perfection that even feels beautiful in form, and the connections are solid, bringing out the full performance of the cartridge (Hiura Katsuji)
Maintenance information: 2026.4.5 continuity confirmed
Accessories: none
Main specifications: aluminum molding, integrated structure, perfect lock system, pin adopted, weight 12 g
Main volume, CD volume, etc. have been disassembled, polished, and maintained! Accuphase line specific preamp. Since it also has a total of 8 input systems, it is convenient for using multiple devices such as CD players. Also, the CD input has a dedicated buffer amplifier and volume, so you can feel the attention to detail in this model. The exterior has dullness and small scratches. Serial L8X241 (Tamura Eiji)
Maintenance information: 2026.4.8 maintained (balance volume replacement main volume, CD volume, compensator switch, balance input changeover switch, disassemble, polish, clean, apply protective agent, RCA terminal polish and clean. Reinstall the solder correction ceiling panel and check the sound of each input/output. There are balanced and unbalanced CD inputs, but please do not connect both at the same time.
)
Accessories: instruction manual
Main specifications: line preamplifier, CD dedicated buffer amplifier, CD dedicated input balanced/unbalanced 1 system each, line input 5 systems, 1 output balance system, 2 unbalanced systems, W475 x H135 x D373 mm, 11 kg
Maintained! Kenwood's dreadnought record player. The cabinet uses a three-layer structure of resin, wood, and aluminum, and exhibits excellent anti-vibration characteristics across all music bands. I am overwhelmed by the clear, powerful, and clear analog sound unique to the heyday of LP records, which is different from MICRO. There are scratches and rust marks on the exterior. Serial 050159 (Yonejima Satoshi)
Maintenance information: 2026.4.8 Maintained (speed, start button disassembly, cleaning and lubrication for oil hardening. The display lamp is dark, so replace the LED. Since the servo circuit rotation fluctuates, the IC was replaced. Electrolytic capacitor replacement. Each rotation lock adjustment. Arm mechanism cleaning. Since elevation does not move, disassemble and apply internal cleaning grease. IFC thread mounting boss creation installation. Spindle motor disassembly shaft lubrication Clean and lubricate the brake mechanism for grease hardening. (Arm operation, voice check)
Accessories: connection cord
Main specifications: quartz lock direct drive DC servo motor 33/45 rotation arm part: static balance universal type J-shaped arm effective length 245 mm overhang 15 mm needle pressure variable range 0 to 2.0 g (0.1 g step) applicable cartridge weight 0 to 9 g (when using the attached shell) 9 g to 22 g (when using the attached shell) applicable cartridge weight 10 g to 34 g body dimensions: W555 x H160 x D470 mm weight 33 kg power supply unit dimensions W130 x H110 x D356 mm weight 4 kg
The price has been drastically reduced! The 2026/4/4 sales price 378,000 yen replacement remote control RC-220 is now in stock. An Accuphase middle class control amplifier made by reviewing the C-275 based on C-290 V technology. The sound stands up well, and the fine mid-high range with good elongation are attractive. This model has a wide range, is smooth, and has a high texture. Serial G0Y108 (Fujisawa Yukishi)
Maintenance information: 2026.4.4 operation confirmed
Accessories: replacement remote control RC-220, connection cable, instruction manual, power cord
Main specifications: full balance circuit, 7 line inputs (RCA x 5/XLR x 2), 2 tape systems, 4 pre-out systems (RCA x 2/XLR x 2), W475 x H150 x D404 mm, 22.5 kg
The price has been drastically reduced. 2026/4/4 sales price 458,000 yen An Accuphase core control amplifier equipped with a revolutionary volume “AAVA” that achieves the same quality as the position of the maximum volume at actual use volume! The amount of information when connected to balance is excellent, and the overwhelming quality when the volume is low is superior. It is a practical preamp with a high degree of perfection. You can see a feeling of use, such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.3.30 Operation confirmed
Accessories: remote control, power cable, instruction manual
Main specifications: input/unbalanced 6 systems/balanced 2 systems/output/balanced 2 systems/unbalanced 2 systems W465 × H150 × D409 mm 18.9 kg
A self-made speaker system that combines the FOSTEX FT66H with JBL's LE8T commercial 20cm unit, 2115A (rubber edge). Both units use Alnico magnets. The sound, which makes you feel the extrusion and depth, is attractive. There is a gap in the attenuator. The lower speaker terminal is not connected internally. You can see a feeling of use, such as appearance, dullness, abrasions, scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.4.7 Operation confirmed
Accessories: none
Main specifications: 2-way FT66H: horn type tweeter unit impedance 8 Ω playback frequency band 2.5 kHz to 22 kHz output sound pressure level 105 dB 2115 A: 20 cm cone type full range Alnico 8 Ω 92 dB playback frequency 40 to 15,000 Hz W510 x H790 x D315 mm 27.5 kg
1 bottle only. Currently sold. Unspecified horn tweeter. If you've been looking for one, take this opportunity. In addition to the exterior and the connector cable being soldered, you can also see a feeling of use such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.3.25 Operation confirmed
Accessories: none
Main specifications: W145 x H66 x D58 mm 150 g (actual measurement)
The last CD-only model in the 1650 series. Equipped with a well-balanced AL24 processing circuit. It supports the foundation of music with a stable mid to low range. The large amount of information peculiar to dedicated CDs is valuable nowadays. There is a thin line scratch on the front panel, and there is paint deterioration on the OPEN/CLOSE button surface (Oikawa Tetsuji)
Maintenance information: 2026.4.2 operation confirmed
Accessories: remote control, instruction manual, power cable, connection cable
Main specifications: 1 digital output system, 1 coaxial system, 1 analog output system, frequency characteristics 2 Hz to 20,000 Hz, W434 × H135 × D340 mm, 12.7 kg
Many deteriorated parts such as capacitors and transistors will be replaced in 2024/2! Fully restored! The second-generation premain amplifier for NEC's masterpiece A-10. Occasionally, it makes a surprising sound that touches the strings. It drives jazz and rock briskly with thick low frequencies and clear mid-high frequencies. Another reason for its popularity is that it is easy to separate power from pre. The exterior has dullness and scratches. Serial 0540359 (Fujisawa Yukishi)
Maintenance information: 2024.2.23 Maintained (power lamp converted to LED. Transistor, capacitor, fuse, heat dissipation sheet, IC, relay, resistor, semi-fixed resistor, zener diode replacement. Resolder after removing old solder from substrates. Switch, relay, and VR contact cleaning. RCA terminal cleaning/plating processing, circuit adjustment, exterior cleaning, confirmation of each input/output, running test)
Accessories: No accessories
Main specifications: output 60+60W (8Ω) phono MM/MC W430 × H150 × D430 mm 23.2 kg
Maintained including replacement of 15 transistors, 13 capacitors, 12 lamps, and 2 volumes. The flagship model of the Macintosh power amplifier at the time. The heavyweight frame, fresh blue meter, and large speakers drive lightly, and the rich, rich tone are just perfect. The clarity of low frequency contours is the highest among all Mackins of all time. There are small scratches and dullness appropriate to the model year (Oikawa Tetsuji)
Maintenance information: 2026.4.6 maintained (GAIN vol failure → both channels replaced
Panel meter dismantling cleaning meter display lamp replacement driver board Tr deterioration, C deterioration, power stage Trxl deterioration → replacement each connector cleaning pattern re-solder mode switching SW dismantling cleaning operation check, offset, bias adjustment)
Accessories: power cable
Main specifications: 500W+500W (1000W when mono) equipped with power guard circuit W483 x D465 x H263 mm 60.3 kg
This is an ultra-compact amplifier equipped with a power amplifier in the DAC's built-in volume controller. Feel free to enjoy PC sound sources. The exterior is generally beautiful. Serial 3962009KU (Matsumoto Tsuyoshi)
Maintenance information: 2026.4.6 sound output confirmed
Accessories: power cord connection cord original box
Main specifications: USB TYPE-B rated output 5W+5W W95 x H52 x D86 mm 316g
An audiocraft headshell that uses a perfect lock pin in addition to its sturdy construction with a hard aluminum molding. It has a degree of perfection that even feels beautiful in form, and the connections are solid, bringing out the full performance of the cartridge.
Maintenance information: 2026.4.6 continuity confirmed
Accessories: none
Main specifications: Perfect Lock pin, hard aluminum molding, dead weight 13.7 g
The price has been drastically reduced! 2026/3/28 sales price 348,000 yen including 28 deteriorated capacitors replaced and maintained! Comes with a remote control. It is a double arm specification with SAEC WE-308 and FR FR-64 BLACK LIMITED VERSION mounted based on the famous SP-10MK2, which is representative of Technics. It is a car that matches SAEC's sharp, good visibility, FR's sense of stability, and sound with a low center of gravity. *When using the WE-308, please remove the dust cover before use. There are threads and bumps on the exterior. (TAMURA Eiji)
Maintenance information: 2026.3.27 Maintained (28 power units, motor servo units, and electrolytic capacitors have been replaced. The rotation lock has been adjusted. The start switch and micro switch in the controller were replaced due to poor contact. The arm elevation seat has been replaced. I created a PU code. The cord was crushed, so I attached the foot. It was created because the hood hinge receiver was damaged. The spindle has been lubricated. Playback operation on both arms was checked.)
Accessories: remote control, power supply, connection cable
Main specifications: Direct drive brushless DC motor quartz phase locked control turntable: made of die-cast aluminum, diameter 320 mm, weight 3 kg WE-308: double knife edge static balance universal type, total length 329 mm, effective length 240 mm, overhang 5 mm, needle pressure 0 to 2 g
FR-64: Dynamic balance type short type needle pressure 0 to 5g W630 x H195 x D440 mm 24 kg
The price has been drastically reduced! 2026/4/3 sales price 248,000 yen Manufacturer maintained! Comes with original box and is in good condition! Made in 2023 While inheriting the traditional design elements of the Marantz design, it is equipped with a high-capacity, high-quality power supply circuit created by modern interpretations. A completely independent power supply circuit dedicated to the preamplifier enables stable operation that is not affected by the power amplifier. It is compatible not only with phono MM and MC, but also with a wide range of modern audio scenes. Serial MBBL062300904 (Fujisawa Yukishi)
Maintenance information: 2026.4.3 manufacturer maintained (replaced due to faulty OLED display tube. Other inspections.)
Accessories: remote control, instruction manual, power cord, connection cord, original box
Main specifications: 120W+120W (8Ω) W391 x D146 x D270 mm weight 13.6 kg
Thorough maintenance has been carried out, such as replacing 44 deteriorated parts, including capacitors, and completely disassembling and cleaning switch contacts! Tubular preamp with a thin design. It has a mild tone with a vintage feel unique to Lux, and the sound quality is well-balanced. The stylish design, which is not typical of a thinly finished vacuum tube, is also excellent. As for the exterior, you can see signs of use such as age damage and dullness. Serial 612226 (Yamato Yuki)
Maintenance information: 2026.4.5 Maintained (31 capacitors, spark killers, relays, 7 vacuum tube sockets, LEDs, 6 diodes, fuses, diffusion caps, and power cords have been replaced. The volume and switch contacts were completely disassembled and cleaned, and the deteriorated parts on the solder surface of the board were re-soldered.
(The input/output waveforms were checked, the left-right balance was checked, and a comprehensive operation test was performed by connecting the power amplifier to confirm normal operation)
Accessories: instruction manual copy power cable
Main specifications: line input, 3 phono systems, 2 tape systems, 2 pre-out systems, vacuum tubes, 12AU7 x 5, 12 AU7 x 2, W465 x H105 x D360 mm (including wood cabinet) 5.5 kg
Comes with original box. Tokyo soundproof turntable seat using vibration-absorbing rubber. The vibration convergence time is overwhelmingly fast, and it effectively absorbs unnecessary vibrations in the frequency band that is important for music playback (Sasaki Shota)
Main specifications: thickness 4 mm x diameter 291 mm weight 330 g
The price has been drastically reduced. 2026/3/7 sales price 59,800 yen revolutions are slightly faster, but the current situation is. DUAL's new generation fully automatic record player. It is an affordable player that can be played with the touch of a button, and is also recommended for those who are new to analog. The 2M red orthophone cartridge is included, so you can use it right away. With a built-in phono equalizer, it can also be connected to a line amplifier. Compatible with 33/45/78 rotations You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2026.3.2 operation confirmed (rotation is slightly faster)
Accessories: cartridge (2M red), power adapter, connection cable, instruction manual
Main specifications: belt drive, 50/60 Hz, built-in phono equalizer, compatible with 33/45/78 rotations, W435 x H145 x D367 mm, 6.2 kg
The disposal price has been reduced. Member prices are not applicable. 2026/3/14 sales price 548,000 yen ※You cannot connect to a LAN without a hub or media converter with SFP. SFP model that can be used with Takutina, Roon Ready, and Diretta. A network player that uses an SFP port for LAN input, which is becoming mainstream recently. The DAC section thoroughly pursues sound quality, and is equipped with an ESS9038PRO, which is famous as currently the highest peak, in mono, and the structure removes noise to the extreme due to separate housing power supplies, so you can enjoy surprising resolution and realism. The main player has a LAN connection, but it can also be used as a USB-DAC. There are multiple threads and dullness on the top plate (Sasaki Shota)
Maintenance information: 2026.3.14 Operation confirmed (sound output up to PCM 768 kHz and DSD512 is OK with Roon Ready, Diretta. Takutina can be used)
Accessories: power cable, connection cable, copy of manual, spike holder, DAC cable, 10M clock unit
Main specifications: input LAN SFP1 system, USB TypeB1 system output RCA, XLR 1 system clock input BNC terminal 50Ω 10MHz main unit W390 x H82 x D327mm power supply W234 x H92 x D236 mm
Every detail has been brushed up, from exterior maintenance to unit maintenance such as screwdrivers! The A7-X model from the late 70s is synonymous with ALTEC's energetic speakers. ATT can also be finely adjusted to MID/HIGH, and it is possible to adjust the high frequency volume affected by the sense of distance and the environment in which it is played. Please enjoy the essence of theater speakers that are still popular today. (TAMURA Eiji)
Maintenance information: 2026.4.4 Maintained (exterior repair/full painting. horn paint. Saran net cleaning/repasting. Woofer maintenance: viscoid droop removal/terminal cleaning. Driver maintenance: magnetic circuit gap cleaning center adjustment, terminal cleaning, phase plug disconnection bonding. Network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/faston terminal replacement. (Unit detachment, horn stay installation processing)
Accessories: none
Key Specifications: 2-way 2-speaker woofer 416-8B, driver 802-8G, horn 511B, network N1201-8A crossover frequency 1.2kHz W755 x H1,350 x D650 mm
Worn parts have been replaced, and maintenance has been completed, including SW class disassembly and polishing. A pure Class A power amplifier featuring a plump, warm tone typical of Luxman. It has both softness and strength, and you can enjoy thick sound quality in the mid to low range. Mono drive with BTL connection is also possible. The exterior has small scratches and a feeling of use such as dullness. Serial W30811341 (Tomonori Asaine)
Maintenance information: 2026.4.4 maintained (panel switch and attenuator disassembly contact polishing. If the screws on this type of LUXMAN speaker terminal are too tight, the plastic will deteriorate and weaken, so it will break. Produced by mounting and processing with a plate. Rear panel changeover slide switch disassembly contact polishing. The output relay was also replaced. Digital meter adjustment 2016.3.11 manufacturer maintained (speaker output relay replaced. The electrolytic capacitor was replaced due to deterioration. Solder deterioration correction. Clean each switch contact. Overall adjustments. (Each operation test)
Accessories: copy of instruction manual
Main specifications: stereo output 55 W+55 W (8 ohms) pure A grade operation, mono output, 220 W (balanced input), frequency characteristics, 5 Hz to 300 kHz, direct reading type level indicator, W444 x H211 x D417 mm, 22 kg
The price has been reduced! 2026/3/27 sales price 69,800 yen This is a record player sold by Project Audio to commemorate the 25th anniversary of its founding. It has a tasteful traditional frame design with a simple yet elegant finish. It's an easy-to-use player with advanced technology in a compact package. The exterior is dull. Serial 004595 (Fujisawa Yukishi)
Maintenance information: 2026.3.27 Operation confirmed
Accessories: instruction manual, connection cord, AC adapter, original box, cleaning cloth
Main specifications: 33,45 (manual speed variable) belt drive 30mm aluminum platter compatible cartridge weight 7.0g-14.0g W460 x H131 x D351 mm 10.2 kg
Refreshed and maintained, including condenser replacement, selector, volume disassembly, cleaning, etc. This is the 4th generation model of NEC's famous A-10. Compared to the predecessor TYPE3, the high frequencies are clear, and overall, I get a slightly calm impression. However, it also has strong sound pressure typical of the A-10 series, and its strength is still alive and well. All input terminals and speaker terminals have been replaced with gold-plated ones (Daiki Goto)
Maintenance information: 2026.4.1 Maintained (All speaker terminals and all input/output RCA jack terminals have been changed from the original terminals. Capacitors, etc. have also been replaced, so there is no need to replace them. Speaker selector, OPERATION, SW, PHONO direct SW, INPUT selector SW, tape copy SW, REC selector polishing grease application, left and right disassembly polishing cleaning for other POWERAMP VR sharp sounds, volume VR disassembly contact polishing cleaning, replacement of 4 speaker relay A output B output locations to confirm interruptions in other speaker sounds, panel, input/output terminal cleaning.)
Accessories: copy of the manual
Main specifications: 60W+60W (8Ω) 120W+120W (4Ω) W430 × H165 × D485mm 27 kg
Everything from exterior refreshes, including the creation of a new saran net, to the unit, attenuator, and network has been fully maintained! This is JBL's masterpiece monitor speaker 4312A that continues from generation to generation. The mid-low range with JBL's original punch is outstanding. The energetic and clear bass makes you hear a slightly different sound from current JBL speakers (Kobayashi Hitoshi)
Maintenance information: 2026.3.30 maintenance completed (enclosure polishing, oil/wax coating, baffle painting, new saran net creation, woofer maintenance: cone paper coating, center cap dent repair on one side, midmaintenance: cone paper coating, frame polishing, tweeter maintenance: one-sided disconnection repair, grill dent repair, network maintenance: frequency characteristic check/ATT cleaning/terminal cleaning)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex crossover 1.1 kHz, 4.2 kHz impedance 8 Ω output sound pressure level 93 dB W362 x H597 x D298 mm 20 kg