Maintained! This time, not only does it have 1 S-shaped one, but it also comes with 2 straight pipes! EXCLUSIVE's super popular analog player. The inside of the thick cab is structured so that the motor part and tone arm part float. When you actually play it, the effect is tremendous, and it brings out the sound of the record to the extreme. There are small scratches, but it is a good category even when viewed from the model year (Oikawa Tetsuji)
Maintenance Information: 2024.6.9 Maintained (Replaced due to semi-fixed volume disconnection. The transistor was replaced due to rotational instability. The electrolytic capacitor has been replaced. The arm bearing was cleaned, operated, and audio-checked. Each rotation lock has been adjusted and the voltage has been adjusted. (Silicone grease attached)
Accessories: transport screws, subweights, 2 straight pipes, silicone oil
Main specifications: linear torque DC Hall motor direct drive dynamic balance type arm needle pressure adjustment range 0 to 3 g W600 x H267 x D415 mm 45 kg
A high-performance integrated SACD/CD player that is the successor to the DP-550. It is a stable sound that makes you feel the thickness of the mid to low frequencies, and the spread of sound from low to high frequencies is not excessive or insufficient. The USB terminal is compatible with 384 kHz 32 bit and 11.2896 MHz 1 bit DSD. The tray button printing is missing. There is a small scratch on the side (Sasaki Shota)
Maintenance information: 2024.6.9 operation confirmed
Accessories: remote control, manual, power cable
Main specifications: 4MDSD+ sampling frequency HS-LINK 32kHz-384kHz (PCM), 2.8224MHz, 5.6448MHz (DSD), coaxial32kHz-192kHz, optical32kHz-96kHz (PCM), USB32kHz-384kHz (PCM), 2.8224MHz, 5.6448MHz (DSD), 11.2896 MHz (DSD/ASIO only) output Level control 0 dB to -80 dB frequency characteristics 0.5-50,000 Hz dynamic range 116 dB dimensions W465 x H151 x D393 mm weight 18.8 kg
Maintained! Comes with original box. Levinson's long-selling prime amplifier. A dual monaural configuration that is thoroughly packed into one chassis while keeping the design concept of separation intact. You can be satisfied with all music genres with quality that easily surpasses separate amplifiers. You can see a feeling of use such as exterior, dullness, abrasions, scratches, etc. (Sasaki Shota.)
Maintenance information: 2024.3.3 Maintained (replace deteriorated parts. DC voltage/DC offset voltage/idling current/other inspection adjustments)
Accessories: original box, remote control, manual, power cable (non-genuine)
Main specifications: 100W+100W (8Ω) XLR input x 2 system RCA input x 3 system gain adjustable (preamp section 0/6/12 dB) W445 x H162 x D483 mm 29.5 kg
* The exterior is in pretty poor condition, so it's cheap. Balance cable, 1.5m pair, MEXCEL coated insulated 7N copper conductor, the polyurethane sheath on the outer skin deteriorates, discolors, whitening, and cracks have entered the entire line cable produced by ACROLINK, and the outer skin has peeled off, and the inner Mexel-coated shield is exposed (Kojima Yosuke)
Accessories: none
A line cable that uses high-purity oxygen-free copper (OFC) wire as a balanced cable with a 1.5m pair of core wires and shielded wires. It's a neutral sound that brings out the individuality of the amplifier or player. The exterior is dull and dirty on the plug and sheath (Kojima Yosuke)
Accessories: none
The 1.5 m pair EQB5 balance cable features a high contrast expression rich in three dimensions, and the gorgeous sound is attractive. The cable coloring is also gorgeous and unique. There is friction on the plug shell (Kojima Yosuke)
Accessories: none
Balance cable uses 1.0 m pair ultra-high purity 7N class CU and is a cable where you can enjoy an overwhelming sense of energy due to pure and dynamic transmission. There are scratches and abrasions on the plug shell (Kojima Yosuke)
Accessories: none
Speaker cable, 2.9 m pair, company Y lag/banana plug specification, 8-core structure, LGC copper conductor, 4 types of different diameter wires, has a sense of energy close to advanced models, and has excellent cost performance. Colored tape is wrapped around some sheaths (Kojima Yosuke)
Accessories: none
This classic headshell is made of magnesium alloy and has an attractive, unobtrusive sound. Overhang and left/right tilt adjustment are possible (Oikawa Tetsuji)
Accessories: none
Main specifications: dead weight 10g
Pair tube, 211 equivalent tube, large triode tube, made in America, actual measured IP value: 47/47 mA (the best standard IP value for this amplifier is 50 mA) with original box ※ sound is checked with a test amplifier, plate current values have been measured, and it has been determined that operation is good (Kojima Yosuke)
Accessories: original box
Pair tube 45 Special compatible ball straight heat triode tube fishing rod type filament measurement value 90/90 (rejection value 55) with white box*Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Pair tube 45 Special compatible ball straight heat triode tube fishing rod type filament measurement value 86/84 (rejected value 55) with white box*Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Speaker cable, 4.5 m pair, Y lug specification, varistrand structure, high purity copper, 8+8 braid structure, Teflon coating. It is a standard model of Kimber Cable that is clear, has a high SN, and has a wide sound field (Kojima Yosuke)
Accessories: none
RCA cable, 1.0 m pair, uses high-purity silver wire with VariStrand structure. KIMBER KABLE's unique “3-core blade structure” is recommended for those who want to improve sound loss anyway. The strengths and weaknesses are clear, and the presence of each instrument, especially the strings of piano, stringed instruments, etc., stretches very nicely. The spread of the mid to low range is also excellent. There is a sense of dynamism that is hard to imagine from the delicate design. There are abrasions on the tubes and plug shells (Kojima Yosuke)
Digital cable, 1.0 m, XLR plug, Teflon, air insulation, double shield, is a digital cable with strength and warmth typical of Caldas (Kojima Yosuke)
Accessories: none
The balance cable 2.0m pair Beltech Shield is also a thick, firm cable with a unique glossy sound. Since there is a lack of high frequencies and tightness in the low frequencies, the music becomes open (Kojima Yosuke)
Accessories: none
The balance cable 1.0m pair Beltech Shield is also a thick, firm cable with a unique glossy sound. Since there is a lack of high frequencies and tightness in the low frequencies, the music becomes open (Kojima Yosuke)
Accessories: none
Speaker cable 1.5 m pair end is an abnormally thin cable for an unprocessed speaker cable. A cable boasting high resolution and a high amount of information. The sound quality changes drastically depending on how you use it, such as separating the main amplifier and speaker, and shortening the speaker cable, so it's fun to drive the sound quality to your liking (Kojima Yosuke)
Accessories: none
※There are no accessories, and the black polarized rubber is missing, so it's cheap. WBT representative spade plug set of 4 High pressure fit with sandwich spade construction It has high rigidity, suppresses the generation of noise and strain in contact areas, and has a structure that can withstand large amounts of current. The plug is dull (Kojima Yosuke)
Accessories: none
A speaker system that makes it possible to reproduce sound with excellent transparency and total balance by adopting the same unit with the know-how of the advanced Ascent. The three-dimensional space radiated from AVALON's unique enclosure and the surprisingly clear sound image with high resolution are still alive and well here. Sound quality that doesn't make you aware of the presence of speakers has created a unique world. There is a feeling of use on the exterior due to small scratches, sunburn, dullness, etc. (Asaine Tomoho)
Maintenance information: 2024.6.9 sound output confirmed (good sweep test)
Accessories: instruction manual saran net jumper cable (general purpose product)
Main specifications: 2-way, 2 speakers, sealed system, floor type, unit used: bass/22cm cone type, treble/2.5cm titanium dome type Playback frequency band: 35 Hz to 24000 Hz ± 1.5 dB crossover frequency: unannounced impedance: 6 ohms output sound pressure level: 86 dB (2.83 V, 1 m) W279 x H991 x D381 mm 43 kg
The price has been reduced. 2024/6/8 sales price 498,000 yen This is AYRE's ambitious work that takes advantage of the characteristics of FETs and uses a perfectly balanced circuit configuration from input to output. A non-feedback type complementary circuit that combines the input stage of a cascade connection with the output stage of the source follower is used. You can listen to a sound with a natural feel that makes you feel the expanse of space. The exterior has scratches and dirt on the front, and there is a feeling of use such as scratches overall (Mizusaki Ryo)
Maintenance information: 2024.6.8 operation confirmed
Accessories: instruction manual, power cord
Main specifications: 200W+200W (8Ω), 400W+400W (4Ω) 100V specification W460 × H180 × D460 mm 43 kg
Special equalizer for photoelectric cartridges. Since there is no resistance to the movement of the vibration system, more delicate playback sound can be expected than conventional cartridges. Since it is a special circuit that supplies power to LEDs, it can only be used with a dedicated equalizer. Cut off the front corner. There is a scratch on the lower part of the rear (Daiki Goto)
Maintenance information: 2024.6.8 operation confirmed
Accessories: instruction manual, power cable
Main specifications: W325 x H96 x D21 mm 5.5 kg
Pair tube direct heat triode tube American double square getter measurement value 62/56 rejection value 38) It is inexpensive because there are few getters with white boxes ※Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Pair tube 45 Special compatible ball straight heat triode tube fishing rod type filament measurement value 84/84 (rejected value 55) with white box*Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Brand new, unopened BOSE TV SPEAKER You can easily improve the sound quality of your TV (Daiki Goto)
Maintenance information: 2024.6.8 operation confirmed
Accessories: original box
Pair Tube 45Special Compatible Ball Direct Heat Triode Tube Fishing Rod Type Filament Engraved Made in America Measured Value 110/110 (Rejected Value 55) It seems to be an unused item due to the state of the tube with the original box! *Pairs are determined based on the gM value measured by the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Alloy die-cast headshell I like the simple design. This is one that is easy to match with various cartridges (Shota Sasaki)
Maintenance information: 2024.6.8 confirmed
Accessories: none
Main specifications: magnesium alloy, die-cast, gold-plated contacts, dead weight 6 g
Pair Tube 45Special Compatible Ball Direct Heat Triode Tube Fishing Rod Type Filament Engraved Made in America Measured Value 110/106 (Rejected Value 55) It seems to be an unused item due to the state of the tube with the original box! *Pairs are determined based on the gM value measured by the test machine TV-7 (Kojima Yosuke)
Accessories: original box
A higher-level model that uses 6N copper as the coil winding for the standard DL-103 cartridge. Compared to the original model, the high range has been increased, resolution has been increased, and the sense of distortion has been reduced. It is a beautiful item with little feeling of use (Mizusaki Ryo)
Maintenance information: 2024.6.8 sound output confirmed
Accessories: instruction manual, original box, needle cover
Main specifications: round needle tip 16.5 microns output voltage 0.25 mV playback frequency 20 Hz to 45 kHz impedance 14 ohms needle pressure 2.5 g dead weight 8.5 g
Maintained! ※It has been changed to an RCA terminal. Marantz's masterpiece CD player equipped with the Philips swing-arm mechanical CDM-1. The sound is rich, analog-like. It has the same feeling of use as time has passed (Daiki Goto)
Maintenance information: 2024.6.8 maintained (slide motor belt NG → replaced. There is poor thru-hole soldering in the decoder board → all re-soldered. Bypass C NG in other servo boards → replace. ~ CD mechanical turntable motor bearing concave → correction ~ reading check)
Accessories: copy of the manual
Main specifications: Philips swing arm mechanism equipped with CDM-1 14 bit DAC W320 x H90 x D300 mm 7 kg
Pair tube 6CA7 compatible ball made in England lot: Xf3 B4B4/Xf4 B4B4 measured value 52/50 (rejected value 30) with white box*Pairs are judged based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: white box
The pair tube seems to be made of RFT due to its 6CA7 compatible sphere structure. Measured value 48/46 (rejected value 30) with white box ※The pair is determined based on the gM value measured by the test machine TV-7 (Kojima Yosuke)
Accessories: white box
Remote control for Ayre K-1 Operation was checked at the company's K-1 x. If you are looking for one, why not (Daiki Goto)
Maintenance information: 2024.6.8 operation confirmed
Accessories: none
You can enjoy voluminous bass with highly efficient and heavy cone paper. It is also durable with a gathered edge, and is also recommended for backload and front load enclosures. There are small scratches etc. on the exterior. Serial 7413 10417 (Tomonori Asaine)
Maintenance information: 2024.6.8 operation confirmed
Accessories: none
Main specifications: rated input 150 W frequency characteristics 30 Hz to 2 kHz 16 ohms efficiency 96 dB crossover frequency 800 Hz recommended enclosure volume 170 to 225 liters depth 146 mm 7.5 kg
A new standard model for the SL-1200 series, inheriting the efforts and results that began with the development of the SL-1200G. Outstanding reliability and stability are now available at an affordable price. I'm also happy that it is compatible with 78 revolutions. There are small scratches and threads on both the body and dust cover on the exterior (Mizusaki Ryo)
Maintenance information: 2024.6.7 operation confirmed
Accessories: instruction manual, power cord, RCA cable, earth cable, original box, subway, shell
Main Specifications: Direct Drive Turntable System Brushless DC Motor Speed 33 1/3, 45, 78 Universal S-shaped Tone Arm Static Balance Needle Pressure Adjustment Range 0 to 4 g Applicable Cartridge Weight/5.6 to 12.0 g, 14.3 to 20.7 g (including headshell) /when using auxiliary weight/10.0 to 16.4 g, 18.7 to 25.1 g (headshell included) W453 mm x H173 mm x D372 mm approx. 11.5 kg
DS-E1 is the entry model for optical cartridges. The mechanism captures the movement of the needle as a change in light and outputs it, and reproduces sound quality with excellent separation and high resolution. The exterior is slightly dull on the body*A dedicated equalizer is essential for use (Ryo Mizusaki)
Maintenance information: 2024.6.7 operation confirmed
Accessories: original box, catalog, wrench
Main specifications: DS-E1: aluminum cantilever, machined aluminum body, output voltage of 500 mV or more, needle pressure 1.6 g to 1.8 g, weight 8.1 g
The price has been reduced! 2024/6/7 sales price 5,000 yen A speaker system that solved problems unique to compact speakers and improved sound quality. A woofer using a 12 cm pure crystal fiber diaphragm is used for the low range, and a 2.5 cm soft dome tweeter is used for the high range. The enclosure has a new round shape with a suede-like coating. The attached stand is detachable. There is a feeling of use on the exterior, such as dullness and small scratches (Jun Tamai)
Maintenance information: 2024.6.4 sound output confirmed
Accessories: saran net
Main specifications: main body W149xH366xD221mm stand W148xH60xD232mm
Weight 5.4 kg (main unit 4.7 kg, stand 0.7 kg)
Pair tube earthquake-resistant military standard product special tube getter large triode tube with white box, measured IP value: 47/47 mA (the best standard IP value for this amplifier is 50 mA) *Sound is checked with a test amplifier, plate current values have been measured, and it has been determined that operation is good (Kojima Yosuke)
Accessories: white box
Pair tube, 5 pole tube, made in America JAN lot: 726/739, measured value 34/30 (rejected value 20) with white box (written on the box) *Pairs are judged based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
The price has been drastically reduced. 2024/6/7 sales price 268,000 yen ※It is cheap because it has scratches. Genuine Oba Shoji product. The uncompromising construction is excellent, with an aircraft-grade machined aluminum block chassis. I am amazed at its compactness and beauty. I'm only particular about the expressive power of the silent part, and the way the faint sound disappears is as clear as if you take your breath away. It's true that it makes me lament the warmth of human skin. There are scratches on the front and back of the top plate on the exterior (Ryo Mizusaki)
Maintenance information: 2024.6.7 operation confirmed
Accessories: remote control, instruction manual, power cord
Main Specifications: Input Terminal Unbalance (RCA) 2 Systems/Balance (XLR) 2 Systems/Bypass, Unbalanced (RCA) 1 System Output Terminal Unbalance (RCA) 1 System/Balance (XLR) 1 System Input Impedance/Unbalance 48kΩ/Balance 48kΩ Dimensions W348 x H75xD191 mm (maximum dimensions) Weight 4.2 kg
*There is no problem with operation, but since it is cheap, it is sold as is. A slim, space-saving Bose tall boy speaker. Although it is a slender speaker, it has a very well-balanced sound and is ideal for multi-channel systems, and it is a model that is fully compatible with 2ch playback. There is paint peeling on the base (Oikawa Tetsuji)
Maintenance information: 2024.6.1 operation confirmed
Accessories: none
Main specifications: 2 way 5 speakers, frequency band, 55 Hz to 20 kHz, impedance 8 ohms, maximum allowable input, 60 W, 85 dB, W85 × H1206 × D100 mm, 5.6 kg
Pair tube large triode tube made in America Actual measured Ip value: 70mA/70mA (the best standard IP value for this amplifier is 75mA) The inside of the tube with the original box is slightly burnt, and there is dirt adhering to the outside of the tube*Sound is checked with a test amplifier, and the plate current value has been measured, and it has been determined that the operation is good (Kojima Yosuke)
Accessories: original box
Pair tube, large triode tube, made in America, measured Ip value: 71 mA/71 mA (the best standard IP value for this amplifier is 75 mA) with original box*Sound is checked and plate current values are measured with a test amplifier, and it has been determined that operation is good (Kojima Yosuke)
Accessories: original box
※It is inexpensive because there are many scratches and there are no second-tier metal fittings at all. The horizontal rack can be used for a wide range of purposes, such as for AV on televisions, etc., and for audio. Compatible with a total load capacity of up to 300 kg. There is a feeling of use such as scratches. ※Shipping costs will be estimated separately (Daiki Goto)
Accessories: none
Main specifications: load capacity: top plate 150 kg or less, shelf board 50 kg or less, bottom plate 50 kg or less W1,165 x H492 x D580 mm weight 62 kg
Oyaide record stabilizer. The vibration mode is optimized with a hybrid configuration of aluminum, brass, and texalum. Unnecessary vibrations associated with platter rotation are attenuated, and sound groove tracing is dramatically improved. It can also be used as an EP stabilizer by reversing it up and down (Daiki Goto)
Accessories: original box, instruction manual
Main specifications: 200g (no weight) to 440g (full weight attached) *Weight can be changed in 40g increments, diameter 70mm, H35mm
Maintenance such as mechanical ASSY replacement has been completed at Denon! A SACD player with a full aluminum chassis and aluminum tray. Similar to the regular series, the D/A section is also equipped with AL24 processing. The supple sound is pleasant enough to listen to. He's an authentic player who doesn't make you feel the size (Daiki Goto)
Maintenance information: 2024.6.6 Maintained (loading mechanism part, traverse mechanism replaced. Each part was inspected and operation tested.)
Accessories: remote control, instruction manual, power cable
Main specifications: SACD/CD player MP3/WMA file CD playable 1-bit DSD/16-bit linear PCM line output 1 system (RCA), 2 digital output systems (coaxial x 1, optical x 1) W300 x H80 x D310 mm 7 kg
*This is a custom-made product that is 90mm wider than SAP-1863. Since it does not come with a stand, it does not stand on its own. Sound Hunter's sound panel using cherry wood. Sound quality can be easily adjusted simply by installing it in a room. The balance between reflection and sound absorption is good, and it creates a natural spread of sound. There are tape marks on the exterior (Mizusaki Ryo)
Accessories: none
Main specifications: W720 x D50 x H1800 mm weight 13.4 kg (actual measurement)
*This is a custom-made product that is 90mm wider than SAP-1863. Since it does not come with a stand, it does not stand on its own. Sound Hunter's sound panel using cherry wood. Sound quality can be easily adjusted simply by installing it in a room. The balance between reflection and sound absorption is good, and it creates a natural spread of sound. There are tape marks on the exterior and scratches on the back (Mizusaki Ryo)
Accessories: none
Main specifications: W720 x D50 x H1800 mm weight 13.4 kg (actual measurement)
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms (Mizusaki Ryo)
Maintenance information: 2024.6.6 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g