Thorough maintenance has been carried out, such as replacing 44 deteriorated parts, including capacitors, and completely disassembling and cleaning switch contacts! Tubular preamp with a thin design. It has a mild tone with a vintage feel unique to Lux, and the sound quality is well-balanced. The stylish design, which is not typical of a thinly finished vacuum tube, is also excellent. As for the exterior, you can see signs of use such as age damage and dullness. Serial 612226 (Yamato Yuki)
Maintenance information: 2026.4.5 Maintained (31 capacitors, spark killers, relays, 7 vacuum tube sockets, LEDs, 6 diodes, fuses, diffusion caps, and power cords have been replaced. The volume and switch contacts were completely disassembled and cleaned, and the deteriorated parts on the solder surface of the board were re-soldered.
(The input/output waveforms were checked, the left-right balance was checked, and a comprehensive operation test was performed by connecting the power amplifier to confirm normal operation)
Accessories: instruction manual copy power cable
Main specifications: line input, 3 phono systems, 2 tape systems, 2 pre-out systems, vacuum tube 12 AX7 x 5, 12 AU7 x 2, W465 x H105 x D360 mm, 5.7 kg
The price has been drastically reduced. 2026/1/23 sales price 79,800 yen. Maintained in 2019 and 2020. LAXMAN's thin preamp. While making you feel a slightly glossy sweetness, I will summarize the music with a clean stretchiness from the mid low to high frequencies. Rather than the dynamic sense of scale, please be attracted by the comfort of the small-scale yet elegantly crafted sound quality. On the exterior of the serial 710397, there are scratches, rust, and a feeling of use on the top plate (Hiura Katsuji)
Maintenance information: 2020.8.12 maintained (PHONO1 matching impedance volume defect replacement, confirmed that there is no level difference or distortion in the waveform with the measuring instrument after repair)
2019.5.15 Maintained (panel lever switch/STEREO/OUTPUT switch disassembly contact polishing, equalizer circuit/power supply circuit and other circuit deteriorated transistors replacement, output relay contact defect replacement, display lamp deterioration replacement, input/output pin jack polish, operation check)
Accessories: none
Main specifications: LINEAR EQUALIZER equipped W438 x H78 x D363 mm weight 6.5 kg
The price has been drastically reduced. 2026/8/21 selling price 128,000 yen A universal player with a relaxed, good mid-range appeal for meat lovers. The vocal expressiveness is overflowing with Luxman's character. I have the impression that it has been upgraded from the Du-7 to the Du-7i and the sense of power has further increased. There are some scratches on the exterior. Serial M31210040 (Tamura Eiji)
Maintenance information: 2026.8.21 Operation confirmed (video unconfirmed)
Accessories: remote control, instruction manual, power cord
Main specifications: DVD audio, DVD video, SACD (multi-channel, stereo), CD, video CD, CD-R, MP3 file compatible audio output/2 channel and multi-channel compatible digital audio output/optical output (TOS-Link 1 system), coaxial output (1 RCA system) video output/D2 (1 system), component (RCA 1 system), S2 (2 systems), composite (RCA 2 systems) size W467 x H148 x D394 mm weight 15.0 kg
Currently sold. Luxman tube harmonizer kit. A supple, warm, and reliable vacuum tube sound. This model was sold as an appendix to Ontomo. It is used by connecting it halfway between the CD and the amplifier. In addition to peeling paint on the exterior and top plate, you can also see a feeling of use such as dullness, scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.8.1 operation confirmed
Accessories: original box
Main specifications: used vacuum tube 12AU7 (ECC82) chassis size: W180 x H80 x D90 mm
The disposal price has been reduced! (Member discounts are not applicable) 2026/7/25 sales price 178,000 yen Switches have been disassembled and polished and maintained! Line-only pre-main amplifier. It is a model that omits both the headphone terminal and the remote control, and has thoroughly implemented simple is best. After all, the middle range is thick and the high range is smooth, lax sound. The supple tone gives a sense of security, and the warmth similar to vacuum tube amplifiers is attractive. The exterior has scratches, floats, and bumps. Serial W31110076 (Tamura Eiji)
Maintenance information: 2026.7.25 Maintained (replacement of faulty IC in the power supply circuit. Switch type disassembly contact polishing. Replace the left and right main amplifier board deteriorated capacitors. Amplifier board soldering correction. Idling current adjustment volume replacement. Bad output relay contact replacement. I/O pin jack polish The main volume of this unit is an ultimate attenuator and cannot be disassembled)
Accessories: instruction manual
Main specifications: 50W+50W (8Ω) W438 × H155 × D446mm 23.0 kg
Disposal price reduction. Member prices are not applicable. 2024/8/23 sales price 12,000 yen wood cabinet for L-507. If you are looking for one, why don't you do it (Daiki Goto)
Accessories: none
Main specifications: W450 x H160 x D268 mm, weight 2.1 kg (actual measurement)
The price has been reduced. 2026/8/12 sales price 298,000 yen The power inlet 3P was replaced with the 2P original, 4 diodes, 6 resistors, etc. were replaced, and all SW and all VOLs were completely disassembled and polished, etc., and the whole body has been refreshed and maintained! The cabinet has also been repaired and finished beautifully. A tubular preamp representing Lux. It is soft and comes out well in the mid and low tones. This is Laxstone! There is no doubt that you will be healed by the soft and warm sound (Oikawa Tetsuji)
Maintenance information: 2026.8.12 Maintained (power inlet 3P replaced with 2P original. All major parts such as coupling capacitors, diodes, knobs, jacks, micro SW, washers, spark killers, etc. were replaced, all SW/VOL disassembly contacts were re-polished, and grease was applied to prevent oxidation and sulfation. (Input/output waveform check, sound output test, cabinet repair)
Accessories: power cable, copy of instruction manual
Main specifications: used vacuum tube/12AX7 x 6, 12AU7 x 1 input/2 phono systems, 3 line systems, 2 tape systems output/2 systems W476 x H190 x D275 mm 12 kg
The disposal price has been reduced! (Member prices are not applicable) 2026/7/20 sales price 3,000 yen. ※The plug has been changed. RCA cable 1.0 m 1 is a 6N conductor cable with excellent resolution. The goodness of the material is well reflected in the sound. The exterior has a feeling of use such as dirt and dullness (Matsumoto Tsuyoshi)
Maintenance information: 2026.7.20 continuity confirmed
Accessories: none
The price has been reduced! 2026/7/12 sales price 99,800 yen Maintained! This pre-main amplifier was announced as a successor to the SQ505. The lax sound of yesteryear has been inherited, and you can feel the nuance of warm vacuum tubes. The output is modest at 35W, but I feel that it is more powerful than the numerical value. Serial 11103088 (Murakoshi Yoichi)
Maintenance information: 2026.7.10 Maintained (board repair, volume ultrasonic cleaning, replacement of 10 deteriorated transistors in the main amplifier circuit. Idling current adjustment volume DC adjustment volume replacement. (I/O pin jack polish)
Accessories: copy of the power cord instruction manual
Main specifications: output 35W+35W (8Ω) PHONOM2 system Recout 2 system dimensions W450 x H160 x D268 mm weight 10 kg
A rare item! System selector series power supply units and remote control units that can switch between multiple devices. Overall there is dullness, dirt, seal marks, etc. (Oikawa Tetsuji)
Maintenance information: 2026.8.1 continuity confirmed
Main specifications: AS-20: W357xH70xD80mm AS-20C: W209xH44xD74mm
Selector unit for small signals in the System Selector series. The switching signal from the company's AS-20/AS-20C is received, and the device is actually switched. *Please note that AS-21 cannot be used alone (Oikawa Tetsuji)
Maintenance information: 2026.8.1 continuity confirmed
Accessories: none
Main specifications: W357 x D70 x D80 mm
Selector unit for small signals in the System Selector series. The switching signal from the company's AS-20/AS-20C is received, and the device is actually switched. *Please note that AS-21 cannot be used alone (Oikawa Tetsuji)
Maintenance information: 2026.8.1 continuity confirmed
Accessories: none
Main specifications: W357 x D70 x D80 mm
Selector unit for small signals in the System Selector series. The switching signal from the company's AS-20/AS-20C is received, and the device is actually switched. *Please note that AS-21 cannot be used alone (Oikawa Tetsuji)
Maintenance information: 2026.8.1 continuity confirmed
Accessories: none
Main specifications: W357 x D70 x D80 mm
The interior has been thoroughly reviewed, such as replacing the vacuum tube socket and condenser, and has been refreshed with a bu-overhaul! After all, the warm and glossy sound quality is excellent for stringed instruments. It has a soft and vivid sound not found in transistors, making it perfect for listening for long periods of time. The exterior is dull. Serial 811243 (Murakoshi Yoichi)
Maintenance information: 2026.7.28 power supply SW replacement (internal terminals cleaned) transformer board correction. The input/output waveform was confirmed, the sound output was checked, and the running test was completed. 2026.5.4 Maintained (vacuum tube (6240G) replaced due to defective vacuum tube. Load test (8Ω load 1kHz 25W+25W), input/output waveform confirmation, sound output check performed, 20h running test completed.) 2025.8.11 Maintained (vacuum tube (50CA10×4), vacuum tube socket, electrolytic capacitor, film capacitor, RCA terminal, semi-fixed VR, spark killer, SP terminal, diode, micro SW, fuse replacement. Load test (8Ω load 1kHz 25W+25W), input/output waveform confirmation, and sound output check
*About the NFB changeover switch This unit is equipped with an NFB changeover switch so that you can select the desired sound quality. (However, if you operate this switch during operation of this unit, shock noise will occur, so be sure to turn off the NFB ON-OFF before switching the power switch.)
Accessories: none
Main specifications: 50CA10 push-pull output 30W+30W W410 x H183 x H160 mm 13.8 kg
Maintenance has been completed with block capacitors, output tube replacement, etc.! This model is based on the concept of making sounds even more straightforward than the MQ60. The warmth of the tone and the indescribable luster sound are truly lackstones. You can see the exterior, dullness, scuff marks, paint peeling, etc. (Murakoshi Yoichi)
Maintenance information: 2026.6.24 Maintained (block capacitor replacement, vacuum tube 2nd stage 12BH7A, 50CA10 pair replacement. Circuit readjustment, input/output waveform confirmation, rated output test (1kHz sine wave, 8Ω load: Lch24.5W+Rch25W, OK), sound output test) 2020.8.25 maintained (50CA10 x 3 output tubes, 12BH7 x 1, coupling capacitor, electrolytic capacitor, rectifier diode, semi-fixed resistor, RCA terminal, SP terminal, MT tube socket, fuse replacement. Gain VOL, impedance switching SW disassembly contact refinement, oxidation and sulfidation prevention grease coating circuit readjusted, input/output waveform confirmed, rated output tested)
Accessories: instruction manual (copy)
Main specifications: used vacuum tube 50C-A10 x 4 12BH7A x 2 6267 x 1 EF86EH x 1 output 25+25W (4/8/16 ohm switch switching) speaker output 1 system W410 x H160 x D205 mm 13.8 kg
It was overhauled in 2020/2, such as replacing the RCA terminal/SP terminal/coupling condenser with an oil condenser. This model is based on the concept of making sounds even more straightforward than the MQ60. The speaker terminals have been changed to banana plug specifications, making it easier to use. The warmth of the tone and the indescribable luster sound are truly lackstones. There is rust, dullness etc. over time on grills etc. (Oikawa Tetsuji)
Maintenance information: 2026.6.16 Operation confirmed
2020.2.12 Maintained (SW/VR junction refinement, electrolytic capacitor, coupling capacitor, rectifier diode, vacuum tube socket, semi-fixed resistor, SP terminal, RCA terminal, fuse, and spark killer replacement. Exterior cleaning, circuit adjustment, waveform confirmation, load test, sound output test)
Accessories: none
Main specifications: used vacuum tube 50C-A10 x 4 12BH7A x 2 6267 x 1 EF86EH x 1 output 25+25W (4/8/16 ohm switch switching) speaker output 1 system W410 x H160 x D205 mm 13.8 kg
In 2024/7, maintenance was carried out with attention to detail, such as capacitor replacement and SP terminal replacement! A kit model of a power amplifier using a 50CA10 3-pole output tube and an OY15 type output transformer, composed of circuits and parts conforming to the MQ60 type, which has been evaluated by LUXMAN. The sound of a vacuum tube has a sense of volume that seems to meet expectations, and it gently envelops you. The sound, which doesn't require scale, is particularly unique, and the slight thickness that spreads from below the mid-range makes you feel comfortable. The exterior has rust, oxidation, and scratches. Serial 574788 (Tomoho Asaine)
Maintenance information: 2024.7.11 Maintained (vacuum tube sockets, block capacitors, electrolytic capacitors, oil capacitors, SP and RCA terminals, semi-fixed VR, fuse holder replacement. Check input/output waveforms and perform sound output checks. Impedance switching SW, gain VOL complete disassembly, contact refinement, and application of grease to prevent oxidation and sulfidation. Input/output waveform confirmation, load test (1 kHz sine wave, at 8 ohm load: 27W+27W, actual measurement), sound output test)
Accessories: none
Main specifications: 30W+30W 50CA10 push pull W410 x H160 x D205 mm 13.8 kg
Vacuum tube sockets, block capacitors, electrolytic capacitors, oil capacitors, SP and RCA terminal replacements, SW and VOL disassembly contact polishing, oxidation and sulfidation prevention grease coating, etc., have been refreshed and maintained. This model is based on the concept of making sounds even more straightforward than the MQ60. The warmth of the tone and the indescribable luster sound are truly lackstones. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2025.6.28 maintained (impedance switching SW/gain VOL disassembly contact polish, oxidation/sulfidation prevention grease application, input/output waveform confirmation, load test (1kHz sine wave, 8Ω load: 20W+20W confirmation) sound output test) 2025.6.26 maintained (vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, semi-fixed VR, fuse holder replacement. Load test (8Ω load 1kHz 20W+20W), input/output waveform confirmation, sound output check performed)
Accessories: none
Main specifications: used vacuum tube 50CA10 x 4 12BH7A x 2 6267 x 1 EF86EH x 1 output 25+25W (4/8/16 ohm switch switching) speaker output 1 system W410 x H160 x D205 mm 13.8 kg
Switches have been maintained, including disassembly and polishing! LUXMAN vintage prime amp from the 60's. Although it is a transistor, it was made in '69, so you can hear the soft, rich sound unique to LUXMAN. The vintage design is a masterpiece that is attractive enough as an interior decoration. The exterior has scratches on the top plate and scratches on the upper front. Serial 10213855 (Yonejima Satoshi)
Maintenance information: 2025.7.27 Maintained (transistors and capacitors have been replaced. Switch type disassembly contact polishing correction. (I/O pin jack polish)
Accessories: No accessories
Main specifications: continuous output 17W+17W W373 x H125 x D227 mm 4.9 kg
All major parts such as coupling capacitors have been replaced, and full maintenance has been completed, including refining all SW/VOL disassembly contacts! A tubular control amplifier representative of Lux. It is soft and produces good mid-range sounds. As you play, the sound becomes more familiar, so this is an amplifier I want you to stay with for a long time. There is Kusumi on the exterior 20109278 (Asaine Tomoho)
Maintenance information: 2025.11.28 Maintained (39 capacitors, 4 diodes, micro SW, spark killer, headphone jack, DIN terminal, 9 vacuum tube sockets, headphone VR, lamp, fuse, power cord replacement. All SW/VOL disassembly contacts have been re-polished, and grease has been applied to prevent oxidation and sulfidation. (Input/output waveform check, sound output test)
Accessories: Power cable, copy of instruction manual
Main specifications: vacuum tube 12AX7 x 6/12 AU7 x 1 using a tubular control amplifier Input: 2 phono system line system 3 system tape system 2 system output: 2 systems W476 x H190 x D275 mm 12 kg
※Shipping service. Special Issue No. 192 = Modern High End Speakers with [Classical] [Popular] Their Diverse Musical Expression/Thorough Audition of New Fall Models (Esoteric = K01X/K03X, Luxman = D08U/D06U, Vivid Audio = G4 GIYA, Magnepan = Mg3.7i, TAD = TAD Compact Evolution One, Weiss = Medus, Boulder = 2110, octave = HP700, Einstein = The Poweramp, Mark Levinson = No. 585, Kronos Audio = Sparta+Helena, Tekdus = TDC01 Ti)/Excellent Recordings in the Digital Age 20 Unknown Must-Listen Editions/Isabelle Faustong Interview/ Published 2014.9.2. Since the photograph is a sample, the actual product may be broken or there may be markings etc.
※Shipping service. 40th Anniversary of the First Issue = Special Issue 159 = Jewel Compact Speaker: Hear That Taste/Quad ESL2805/Luxman C1000F/Claire EVO Series Detailed Report/Enjoy Vintage/Released on 2006.7.15. Since the photograph is a sample, the actual product may be broken or there may be markings etc.
※Shipping service. No. 58 Special Feature = 3rd <THE STATE OF THE ART SUPREME COMPONENT> AWARD SELECTION/ NEW JBL4345 Detailed Report/ EMT927VS Torrence Reference/Listen to Tannoy SRM Series/Infinity “IRS” Anatomy/1981.4.15 issue. Published models: JBL/4345BWX MCINTOSH/MC2500 VICTOR/TT-801, CL-P10, TS-1 MICRO/SX-8000, HS-80 ONKYO/INTEGRA P-309, INTEGRA M-509 MARK LEVINSON/ML-6AL AUDI-TECHNICA/AT-34E11 ENTRE/EC-30 SME/3012-R SPECIAL TECHNICS/EPC-C100CMK3 FIDELTY RESEARCH/XF-1 SELLESION/DITTON300 KEF/MODEL105.4 KENWOOD/L-08C, L-08M PIONEER/A-980 SANSUI/AU-D907F SONY/TA-AX8 LO-D/TU-1000 LUXMAN/PD300 ADC/ASTRION LINN/ASAK/ S56.4.15 issued. Since the photograph is a sample, the actual item may be broken or have markings etc.
※Shipping service. No. 189 Special Feature = Stereo Sound Grand Prix 2013 (Magico = Q7, Esoteric = Grandioso P1+D1, Focal = Grande Utopia EM, YG Acoustic = Hailey 1.2, Piega = Coax 120.2, Voxative=Ampeggio Signature, Lynne = Akubarik, Sonus Faber = Olympica III, KISO Acoustic = HB-X1, Fostex = G2000a, Fundamental = RM10, Elac = BS312, Orpheus = Heritage SACD HE+DAC Mk3 HE, TAD = TAD-D1000, AccuFuse = DP720, Denon = DCD-SX1, Yamaha = CD-S3000, Marantz = NA11S1, Sony = HAP-Z1ES, Qualia & Company = Indigo Line Amplifier, Dan Dagostino = Momentum Preamplifier, Mark Levinson = No. 52, Luxman = C900u, audio note = Kagura, Einstein = The Final Cut MK70 Limited, viola = Concerto, phasing = MA1000, Uesugi = U · Bros 300, Devialet = Devialet 240 Constellation Audio = Perseus) /2013-2014 539 Best Buy Components by Genre/Price Range/Thorough Audition of New Winter Models/Published 2013.12.9. Since the photograph is a sample, the actual product may be broken or there may be markings etc.
※Shipping service. No. 158 Special Feature = 40th Anniversary = Exciting Sound: Fascinating Components & Discs/Luxman 80th Anniversary Interview/New Series: Between Analog and Digital/Published on 2006.4.15. Since the photograph is a sample, the actual item may be broken or have markings etc.