Maintained by Accuphase Service! A core power amplifier representing the Accuphase in the mid-80s. Neat sound design, just like Accuphase. A highly complete car that harmonizes high resolution and thickness in an exquisite balance. It is a famous model that was used as a reference power amplifier for various FM magazines at the time. There are scratches on the side corner and front (Sasaki Shota)
Maintenance information: 2024.4.27 Maintained by the manufacturer (due to poor output relay contacts, both A/B were replaced with sealed types. Front, push button switch contact cleaning. Level volume left and right disassembly contact cleaning. (The meter and logo lamp were replaced, the carbon resistance in the power amplifier Ass'y was exchanged left and right, and internal inspection and cleaning characteristics were checked)
Accessories: manual
Main specifications: output 250 W+250 W (8 ohms) frequency characteristics 20 Hz to 20,000 Hz gain 28.0 dB load impedance 2 to 16 ohms damping factor 500 W 481 x H218 x D445 mm weight 33.5 kg
The interior has been completely overhauled! This is an 811A push-pull tube power amplifier. You can enjoy an overhanging vacuum tube sound with luxurious mono specifications where the woofer is properly braked. The thick, cored sound in the low range makes you feel the momentum and strength unrivaled for a vacuum tube. The entire exterior has scratches and dullness over time (Sasaki Shota)
Maintenance information: 2024.4.26 Maintained (vacuum tube 5R4GY strain and deterioration replacement. 1W resistor distortion and deterioration replacement. 25W resistance deterioration and pair replacement. Vacuum tube 6W6 deterioration replacement/vacuum tube 6SN7 defective replacement. Block capacitors 40 μF x 2 made in Japan → replaced with CE ones. 1 x 2 Vacuum Tube Socket and RCA Jack Caulking Repair Rated output: 85 to 120 W with AC 100 to 117 V, measured at SP: 8 ohms)
Accessories: none
Main specifications: vacuum tube 811A x 4, 5R4GY x 8, 6W6GTB x 4, 6SN7GTB x 2, 12AX7 x 2, 165W+165W W482 x H272 x D310 mm
The price has been reduced! 2020/11/9 sales price 70,000 yen maintenance completed. This is a 2-way network. Since bass can be pushed out well, and high frequency adjustment ranges can be obtained with 2 types of HF/MF attenuators, it is a model that is easy to match the desired sound quality. There are small scratches on the exterior due to the feeling of use. Serial 05234 07210 (Makoto Kono)
Maintenance information: 2020.11.9 maintained (common wiring reinforcement terminal solder removal, rust removal treatment, cleaning, ATT (x4) contact disassembly cleaning, contact grease application, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound check)
Accessories: none
Main specifications: W114 x H190 x D228 mm 1.8 kg Crossover frequency 1.2 kHz Impedance 8 ohms Level control is continuously variable up to -8 dB in the middle range is 2 kHz and the high range is continuously variable up to -6 dB at 10 kHz
Maintained! Woofer unit used in A5. It is a 38cm Alnico magnet, and the open sound is truly Altec. As for the exterior, the cork around the frame has deteriorated (Mizusaki Ryo)
Maintenance information: 2024.4.28 Maintained (edge holes repaired with rubber adhesive, edge wood chips removed, center cap removed and dustproof net glued, magnetic circuit slit cleaned, rust prevention, coil bobbin center removal)
Accessories: none
Main specifications: 38cm cone woofer unit impedance 16 ohms output sound pressure level 104 dB 12.4 kg
The disposal price has been reduced! Member prices are not applicable. 2024/4/24 sales price 118,000 yen*The saran net is cheap because it is not in good condition due to lack of stock, scratches, etc. ATC small bookshelf The thick and powerful mid-low range is attractive. If you pair it with a good amplifier that has torque, you can enjoy it on a scale that greatly exceeds its size. There are scratches on the exterior. Serial 0819/0820 (Tamura Eiji)
Maintenance information: 2024.4.24 sweep test good
Accessories: No accessories
Main specifications: 2 way 2 speakers sealed impedance 8 ohms size W211 x H380 x D250 mm weight 11.4 kg
The stylus is good, but since the cantilever is curved, it is inexpensive. A mono-only cartridge with a traditional 33 series body. Play mono records clearly with a pick-up that is only horizontally oriented. It has vertical compliance and is optimized for recurrent mono editions in the stereoca era. The range is wider than Denon's DL-102 and you can feel the expansion (Fujisawa Yukishi)
Maintenance information: 2023.8.29 Operation confirmed
Accessories: needle cover
Main specifications: MC type needle pressure 2.3 to 2.7 g (2.5 g standard) Muku round needle high hardness duralumin cantilever PCOCC coil anti-vibration rubber “honeynight” impedance 10 ohms 6.9 g
High output MC cartridge for mono LPs only. Plays deep sound that was not produced with stereo cartridges. It has the vividness unique to Technica, but the three-dimensional effect and intensity are an appeal unique to mono (Oikawa Tetsuji)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: needle cover
Main specifications: high output MC type output 1.2 mV needle pressure 2.0 g impedance 40 ohms dead weight 6.8 g
Disposal prices have been reduced! Member discounts do not apply. 2023/4/2 sales price 10,000 yen*Currently sold. The safety wire is broken. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, such as fading, abrasions, etc. (Kanai Hidetsugu)
Maintenance information:2023.4.2 sound output confirmed
Accessories: none
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced. Member discounts do not apply. 2022/12/29 sales price 10,000 yen. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information:2022.12.28 operation confirmed
Accessories: instruction manual (copy)
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced. Member discounts do not apply. 2022/12/29 sales price 10,000 yen. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information:2022.12.28 operation confirmed
Accessories: instruction manual (copy)
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced. Member discounts do not apply. 2022/12/30 sales price 10,000 yen. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information:2022.12.28 operation confirmed
Accessories: instruction manual (copy)
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced! Member discounts do not apply. 2023/4/2 sales price 10,000 yen*Currently sold. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use such as exterior, fading, abrasions, etc. (Kanai Hidetsugu)
Maintenance information: 2023.4.2 sound output confirmed
Accessories: none
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
*Currently sold. The classic 101 mm small speaker. The sound, which has been compiled in one small full-range shot, makes all kinds of popular music sound cheerfully. The exterior has scratches, threads, and dullness. There is also a dent in the saran net. Serial 108023/089692 (Tamura Eiji)
Maintenance information: 2024.3.3 sweep check OK
Accessories: saran net
Main specifications: 1 way 1 speaker impedance 6 ohms maximum input 150 W output sound pressure level 86 db W232 x H154 x D172 mm 2 kg
Disposal prices have been reduced! Member discounts do not apply. 2023/4/2 sales price 10,000 yen*Currently sold. The safety wire is broken. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. On the exterior, there is a feeling of use, such as cracks, fading, abrasions, etc. on the main body (Kanai Hidetsugu)
Maintenance information: 2023.4.2 sound output confirmed
Accessories: none
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
The price has been reduced. 2024/2/20 sales price 49,800 yen 2-way bookshelf speaker system. It's the most compact speaker in the company's 600 series, yet it's second to none in terms of power and accuracy due to the new separate double dome tweeter and design improvements. It is in good condition (Sasaki Shota)
Maintenance information: 2024.2.20 sweep test good
Accessories: none
Main specifications: playback frequency 54 Hz to 50 kHz efficiency 85 dB impedance 8 ohm crossover 4 kHz dimensions W160 x H315 x D229 mm weight 4.6 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/13 sales price 398,000 yen For the first time in about 7 years, CM10S2 has arrived! It lets you listen to high-response sounds. In addition to simplifying the crossover with Mundorf EVO capacitors, all important internal components have been improved, such as Vandenhall internal wiring, nickel-plated terminal trays, and the driver's anti-vibration dust plug. As for the exterior, there are scratches, threads, and deterioration in part of the urethane. Serial 1508-0011895, 1508-0011896 (Fujisawa Yukishi)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, saran net, spikes, rubber feet, jumper plates
Main specifications: 3-way bass reflex type playback frequency band 28 Hz to 50 kHz output sound pressure level 90 dB nominal impedance 8 ohms W366 x H1087 x D414 mm weight 33.5 kg
The price has been reduced! 2024/4/28 sales price 398,000 yen A popular model equipped with a diamond tweeter that rewrote the history of the 800 series. The color is rose. The excellent stretch that penetrates the high range without habit and the sense of volume in the mid to low range, which has a strong presence, are appealing not found in the current D3. The exterior has dullness, small scratches, and stickiness on the bass reflex. Serial 0012701 0012702 (Asaine Tomoho)
Maintenance information: 2024.4.28 sound output confirmed
Accessories: saran net jumper cable
Main specifications: 2 way 2 speakers bass reflex diamond dome tweeter 8 ohm crossover 4 kHz frequency characteristics 42 to 33 kHz W238 x H418 x D351 mm 12 kg
The disposal price has been reduced. Member prices are not applicable. 2023/10/23 sales price 29,800 yen ※Currently sold. Comes with a special case! Portable headphone amplifier with built-in D/A converter. DSD256 (11.2 MHz/1 bit) PCM supports native playback of up to 768 kHz/32 bit. Please enjoy the sound quality unique to a thick mojo in the mid to low range. There is dullness and a feeling of use (Sasaki Shota)
Maintenance information: 2023.10.23 Operation confirmed
Accessories: original box
Main specifications: output level 35 mw/600 ohm, 720mw/8 ohm, output impedance 0.075 Ω, dynamic range, 125 dB input system, 3 optical systems, 1 coaxial x 1, microUSB x 1, 2 output systems, headphone jack x 2, charging time, approx. 5 hours continuous operation time, approx. 8 hours W82 x H60 x D22 mm 180 g
Beautiful item with original box! DENON's classic MC cartridge. The balance of localization and sound is excellent, and all music genres can be played without difficulty. I can recommend this cartridge to a variety of people, from analog beginners to experts (Fujisawa Yukishi)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual, original box, needle cover
Main specifications: MC type output voltage 0.3 mV playback frequency 20 Hz to 45 kHz electrical impedance 40 ohms needle tip 16.5 microns round needle pressure 2.2 to 2.8 g dead weight 8.5 g
A standard model of domestic mono cartridges. A popular model that condenses the appeal of a mono needle, which has a thick overall sound and is also powerful. It is also attractive that the output is high and can be used without a step-up transformer (Murakoshi Yoichi)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: case, needle cover, instruction manual
Main specifications: output voltage 3 mV playback frequency 50 Hz to 10 kHz impedance 240 ohms compatible load 1 kΩ or more needle tip 17 microns diamond round needle needle pressure 3G
※It is cheap because it is in poor condition. Denon's MC cartridge used to be an introduction machine. The sound quality has a sense of transparency that extends smoothly from low to high frequencies without clogging. The famous DL-103 Yuzuri cartridge has a good balance of range, density, and volume. In addition to being dull on the exterior, there is a feeling of use such as the part number plate peeling off. Serial 6984 (Hiroki Aso)
Maintenance information: 2024.4.27 sound output confirmed
Accessories: none
Main specifications: MC type 0.3 mV internal impedance 40 ohms needle pressure 1.5 to 2.1 g special elliptical needle double structure tapered cantilever dead weight 4.5 g
A classic MC boost transformer. With 2 input systems, impedance can be switched to 3.40 ohms, and comes with a PASS line, you can freely enjoy various cartridges and tone arms (Takasaki Atsushi)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.2.13 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
※Overall, there is dullness, rust, and scratches, and there is a feeling of use, so it is inexpensive. A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. (MIZUSAKI Ryo)
Maintenance information: 2024.1.27 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
A classic MC boost transformer. With 2 input systems, an impedance of 3.40 ohms switchable, and a PASS line, you can freely enjoy a variety of cartridges and tone arms. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.11.18 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input, 2 systems, switchable, 1st order impedance 40 Ω, 3 Ω, switching, 2nd order impedance 4 kΩ, boost ratio 1:10, frequency characteristics, 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
A classic MC boost transformer. With 2 input systems, an impedance of 3.40 ohms switchable, and a PASS line, you can freely enjoy a variety of cartridges and tone arms. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2023.12.18 operation confirmed
Accessories: none
Main specifications: MC boost transformer input, 2 systems, switchable, 1st order impedance 40 Ω, 3 Ω, switching, 2nd order impedance 4 kΩ, boost ratio 1:10, frequency characteristics, 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
The price has been reduced! 2024/4/27 sales price 23,000 yen This is a standard model of domestic mono cartridges. A popular model that condenses the appeal of a mono needle, which has a thick overall sound and is also powerful. It is also attractive that the output is high and can be used without a step-up transformer (Asaine Tomoho)
Maintenance information: 2024.4.27 sound output confirmed
Accessories: none
Main specifications: output voltage 3 mV playback frequency 50 Hz to 10 kHz impedance 240 ohms compatible load 1 kΩ or more needle tip 17 microns diamond round needle needle pressure 3G
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. There is dullness and a feeling of use (Sasaki Shota)
Maintenance information: 2024.3.30 Operation confirmed
Accessories: manual
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
A higher-level model that uses 6N copper as the coil winding for the standard DL-103 cartridge. Compared to the original model, the high range has been increased, resolution has been increased, and the sense of distortion has been reduced. The exterior has a feeling of use such as dullness. Serial 1226 (Tomoho Asaine)
Maintenance information: 2024.4.27 sound output confirmed
Accessories: none
Main specifications: round needle tip 16.5 microns output voltage 0.25 mV playback frequency 20 Hz to 45 kHz impedance 14 ohms needle pressure 2.5 g dead weight 8.5 g
A limited edition model commemorating the 15th anniversary of the famous DL-103 cartridge. It is a step-up transformer that was sold as a set as the DL-103 T2 at the time, and it has a solid framework and a thick sound. The exterior is scratched, dull, and has a feeling of use (Katsuji Hiura)
Maintenance information: 2024.4.28 sound output confirmed
Accessories: none
Main specifications: frequency band 20 Hz to 70 kHz 40 ohms crosstalk 60 dB or more W92 x H55 x D145 mm 720g
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/1 sales price 298,000 yen Interior and exterior refreshment maintenance has been completed and brushed up! A consumer model of the 2S-305, a timeless monitor speaker masterpiece that Japan is proud of. The thick and clear midrange and detailed high frequencies, which cannot be felt with the look, vividly reproduce vocals. The sound that accurately expresses the characteristics of an amplifier that is set regardless of whether it is a vacuum tube or transistor makes me feel the goodness of the device I have on hand that I haven't been able to see until now. The exterior is in perfect condition due to maintenance. Serial 351364 4851370 (Yamato Yuki)
Maintenance information: 2023.12.1 Maintained (exterior polishing, oil finish, exterior repair, front and rear baffle painting to create missing parts, saran net replacement, velcro replacement. Woofer maintenance center adjustment, edge damping agent application, disconnection solder treatment, center cap dent correction. Tweeter maintenance center cap internal cleaning and replacement, center adjustment, corn paper edge crack repair, edge damping agent application, unit detachment. Network maintenance frequency characteristics check, ATT contact cleaning, terminal cleaning sound operation confirmed)
Accessories: saran net
Main specifications: 2 way bass reflex system input impedance 8 ohms output sound thickness level 96 dB crossover frequency 1500 Hz W650 × H880 × D445 mm weight 50 kg
※The veneer is peeling, the top plate is undulating, and the grill is indented, so it is inexpensive. This high CP model was released in the 49th year of Diatone's founding. It has a very well-balanced, rounded, and gentle tone. I can do everything from jazz and rock to classical and pop music as an all-rounder (Oikawa Tetsuji)
Maintenance information: 2024.4.15 Operation confirmed
Accessories: none
Main specifications: 3 way 3 speakers, 6.3 ohms, sound pressure level, 90 dB, W380 x H680 x D295 mm, weight 25 kg
Disposal prices have been reduced! (Member discounts are not applicable) 2023/2/5 sales price 10,000 yen ※1 bottle only. DynAudio's classic 17cm cone woofer. It has resolution and is recommended for bookshelves, etc. The urethane on the back magnet side has not deteriorated (Tamura Eiji)
Maintenance information: 2023.2.5 good sweep test
Accessories: There are no accessories
Main specifications: 17 cm cone type impedance 4 ohms diameter 176 mm depth 66.5 mm
The disposal price has been reduced. Member discounts are not applicable. 2023/5/5 sales price 9,800 yen. ※1 bottle only. A crossover network with exactly the same structure as the company's X8. This network is recommended when using BB4 with a T350 or 12TRXB. There is a feeling of use such as peeling and scratching on the label (Mizushima Itsuro)
Maintenance information: 2023.5.5 operation confirmed
Accessories: none
Main specifications: crossover frequency 3,500 Hz 8 ohms allowable input 100 W external dimensions W114 x H89 x D92 mm weight 680 g
The price has been drastically reduced! 2024/4/27 sales price 178,000 yen rare item. Fidelix MM/MC compatible phono equalizer. The amplifier section uses an all-FET NFB type. The equalizer curve is variable, and it is possible to switch between 5 levels of low frequency characteristics of 50 Hz or less and high frequency of 2 kHz or more, respectively. In addition to RIAA, it is compatible with SP, NAB, AES, FFRR, old RCA, and COLUMBIA, and is equipped with a total of 25 types. (FUJISAWA KOSHI)
Maintenance information: 2024.4.27 Inspection operation confirmed (when MC is input at 1 GΩ, ① knock down dip switch No. 2 No. 5 to the front side. It can be used by ② tilting the DIP Switch No. 1 and 6 to the front side ③ and inserting the short pin into the MM terminal). (MC input setting for current 330 ohm load) Operation was tested with each function for internal inspection of the main unit and power supply unit.)
Accessories: power supply unit, copy of instruction manual
Main specifications: input impedance MC · 1 gΩ or 330 Ω/mm · 47 kΩ output impedance RCA 100Ω/XLR · 200Ω gain MC · 65dB/mm40dB main unit W150 x H50 x D250 mm approx. 1.2 kg power supply approx. W65 x H50 x D130 mm weight approx. 0.6 kg
※1 bottle only. This is a 10 cm full range unit from FOSTEX. It is a very popular model for those who make their own speakers. The sound quality is bright and has an impression of tension. Dull, there is a feeling of use (Sasaki Shota)
Maintenance information: 2023.8.11 sound output tested
Accessories: manual, original box
Main specifications: full range aperture 10 cm maximum input 15 W 8 ohms magnetic flux density 13000 gauss baffle aperture diameter 9 cm recommended enclosure volume 15 L
Fidelity-Research step-up transformer A multifunctional boost transformer that can be switched from 3 ohms to 100 ohms, has 3 inputs and PASS, and can also be used as a selector for multiple record players. Each gain is equipped with an independent toroidal transformer. The exterior is dull, and there are small scratches (Oikawa Tetsuji)
Main specifications: boost transformer core format/toroidal core input impedance 3Ω, 10Ω, 30Ω, 100Ω, PASS (switching) load impedance 47 kΩ to 57 kΩ frequency characteristics 20 Hz to 30000 Hz W170 × H60 × D180 mm 1.2 kg
The price has been drastically reduced! 2024/4/17 sales price 69,800 yen ※It is cheap because it has a tobacco smell. Hi-Fi Man's planar drive headphones have a high resolution, and the low frequencies are clear and easy to listen to. The sound balance is flat and the high cushioning is also impressive. The exterior smells like tobacco and there are creases on the cable (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box, connection cable
Main specifications: planar drive impedance 50 ohms sound pressure sensitivity 83.5 dB playback frequency band 8 Hz to 65 kHz 505 g
The price has been drastically reduced. 2024/4/10 sales price 10,000 yen. Coaxial cable 0.9 m 75 ohm collet chuck plug From the shield notation, it seems that the cable is also made by ZAOLLA. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.8 continuity confirmed
Accessories: none
The price has been drastically reduced. 2024/4/28 Infiniti's best-selling speaker with a sales price of 148,000 yen. It's a 3-way system that brings out quite a bit of volume for a tall boy type. The bass is also sufficiently reproducible with a sense of scale coming out of the double woofer, and even pipe organs can be reproduced with plenty of room. There is a slight feeling of use, such as dullness on the SP terminal and jumper. Serial 07170/07217 (Takasaki Atsushi)
Maintenance information: 2024.4.27 sound output confirmed
Accessories: manual, saran net, jumper, spike holder (8 general-purpose items)
Main specifications: 3-way system frequency characteristics 35 to 450,000 Hz crossover 250/3,500 Hz 6 ohms W390 × H1200 × D380 mm 40 kg
The price has been reduced. 2023/12/31 selling price 19,800 yen Infiniti's slightly rare center speaker. Unlike a domestically produced center speaker that mainly plays the vocal band, you can feel the nuance of a Scandinavian speaker that plays as if it were floating in space. There are small scratches on the exterior, and the saran net is partially torn (Oikawa Tetsuji)
Maintenance information: 2023.12.31 operation confirmed
Accessories: none
Main specifications: 3 way 4 speakers 6 ohms W509 x H230 x H270 mm 12.5 kg
Maintained! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, there is a feeling of use, such as paint peeling off and scratches scattered around. Serial 17041 17049 (Hiroki Aso)
Maintenance information: 2023.3.31 Maintained (terminal rust removal, acid wash, insulating bushing & mounting screw replacement, ATT brand new replacement, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound output check)
Accessories: none
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
Refreshed and maintained with internal and external maintenance! The clear and dynamic sound quality, and the deep, powerful sound of 123A is more powerful than its size, and makes you enjoy jazz and rock excitedly. This speaker is perfect for playing jazz on records (Yonejima Satoshi)
Maintenance information: 2024.2.28 Maintained (enclosure polishing/oil/wax coating, baffle painting. Maintenance: frame polishing/oil finish, net replacement. Woofer cone paper paint. Tweeter maintenance: New urethane ring created, frame cone paper coating. Network maintenance: frequency characteristic check, ATT disassembly cleaning, terminal cleaning/screw replacement)
Accessories: saran net
Main specifications: 2 way 2 speaker bass reflex bookshelf type unit configuration high range LE25 (3.6 cm) + low range 123A (30 cm cone) impedance 8 ohms crossover frequency 2 kHz dimensions W360 x H600 x D 300 mm weight 20 kg
Maintained! A network with a crossover frequency of 7 kHz. It is ideal for MID/HIGH for 3-way systems using 2440. There is a small wound (Oikawa Tetsuji)
Maintenance information: 2024.4.17 Maintained (2 VR attenuators, 12 screws, 24 insulating washers replaced)
Accessories: none
Main specifications: crossover frequency 7 kHz, allowable input (continuous program), 50 W impedance, bass range: 12 to 16 ohms, treble range: 12 to 16 ohms, treble attenuation/variable volume, mounting hole W140 x 108 mm 0.7 kg
The price has been drastically reduced! 2024/3/17 sales price 69,800 yen JBL professional tweeter. Since it is designed to make the sound fly far, the sound quality is solid and more straight compared to the company's consumer model 077. The mid to high frequencies are vivid, and the low frequencies are finished with a tight sound. The exterior has dullness and small scratches due to aging. Serial 81380/52416 (Yonejima Satoshi)
Maintenance information: 2024.3.17 sweep test good
Accessories: No accessories
Main specifications: horn type tweeter impedance 16 ohms playback frequency band 6,500 to 21,500 Hz (manufacturer specified), crossover 7 kHz, efficiency 105 dB, W100 x D84 mm, 3 kg/book
The price has been drastically reduced! 2024/4/25 sales price 118,000 yen ※The horn part and equalizer part have been replaced with brass ones. Comes with a horseshoe ring! 16 ohm specification A straight, carefree, and linear sound. It's great for applying sharp, edgy cymbal sounds and attack sounds. The impression is that the density has increased compared to the 8 ohm specification. The back plate is missing. The exterior has slight paint baldness and oxidation. (YONEJIMA Satoshi)
Maintenance information: 2024.4.25 Maintained (Fram pull-out wire disconnection repair (only repair only the fault location because the Fram drawer line is thin) Fram cleaning. DCR (? /6.5 ohm diaphragm no scratch) DCR (40886/6.6ohm diaphragm no scratch)
Accessories: horseshoe ring
Main specifications: horn type tweeter unit, alnico magnet, 8 ohms, crossover frequency, 2,500 Hz, allowable input, 20 W, 2 kg/bottle
Maintained in October 2022! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, paint is bald and oxidized (Yonejima Satoshi)
Maintenance Information: 2022.10.7 Maintained (Terminal rust removal, acid cleaning, insulation bushing & mounting screw replacement. ATT replacement A frequency characteristic measurement check (~ approx. 42 kHz) was performed, and the original capacitor was continuously used for good results. Input/output waveform and balance check, sound output check.)
Accessories: no accessories
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
Maintained. The grain of the sound is clear and the smoothness of the connection has also been improved. This is a 1200 Hz crossover network ideal for the combination of a 38 cm woofer and 1 inch driver. The exterior has dullness and scratches due to use over time, serial 18254 18275 (Asaine Satoshi Law)
Maintenance Information: 2024.4.16 Maintained (Screws, Insulated Washer Parts Replacement Switch Contact Cleaning)
Accessories: none
Key Specifications: Crossover 1200 Hz 8 Ohm 3 Position Switch with Level Control
※1 bottle only. Maintained! The classic model for professional 1" screwdrivers. It is a driver that is installed in many of the company's 43 series, etc., and is easy to balance with various woofers and tweeters (Daiki Goto)
Maintenance information: 2024.4.23 Maintained (diaphragm installation adjustment, replacement of the following parts. DCR (54871, 5.7 ohm diaphragm, no scratches)
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms (measured 10/12 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/22 sales price 148,000 yen Maintained! A driver unit suitable for sound reproduction for large halls and theaters, modeled after the standard 2-inch 375. High frequency characteristics have been enhanced while retaining a vintage feel. The cymbals play a sound that makes you think of jazz. The paint is peeling off. Serial 32769, 32799 (Fujisawa Yukishi)
Maintenance information: 2024.4.22 maintained (diaphragm installation adjustment, pad dampener replacement)
Accessories: No accessories
Main specifications: frequency characteristics, 500 to 18 kHz, crossover, 500 Hz, 16 ohms, diameter: 175 mm, height: 145 mm, approx. 11.8 kg/bottle