The disposal price has been reduced! (Member prices are not applicable) 2026/5/14 sales price 1,280,000 yen Full maintenance was completed in 2024/12 after spending plenty of time on the unit, network, and exterior! This is an AUTOGRAPH with an HPD385 mounted in a genuine TEAC box. I am overwhelmed by the majestic sense of scale and profound and vivid sound image expressed by the low range backroad horn and the mid to low range front short horn, and it also has a good supple and beautiful tone that cannot be obtained with TANNOY in recent years. The exterior is in a state where there is a slight feeling of use over time, but it is generally beautiful depending on maintenance (Yamato Yuki)
Maintenance information: 2026.4.18 caster installation 2024.12.15 maintained (exterior repair/polishing/clear finish, front and rear baffle repair/paint maintenance: net cleaning/repasting, fraying repair/frame repair. Unit maintenance: low pass side edge exchange, magnetic circuit gap cleaning center adjustment, fastener polishing, high frequency side magnetic circuit gap cleaning center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, faston terminal replacement, 4-pin terminal/terminal cleaning)
Accessories: saran net
Main specifications: 2-way, 1 speaker, all-horn system, corner type usage unit, 15 inch (38 cm), HPD385 impedance 8 ohms, W1070 x H1530 x D660 mm, 78 kg/book
The price has been reduced! 2026/5/23 sales price 348,000 yen Maintained! Thread-driven analog system It is a popular configuration that combines the heavyweight gunmetal turntable RX-2000 with the upper motor unit RY-3300 and the standard MA-505 arm. The smooth, quiet rotation and the thick mid-low range are attractive. It has the stability and amount of information typical of a large turntable, and you can enjoy rich analog sound that is difficult to obtain with modern machines. There is a feeling of use on the exterior such as dullness and small scratches (Asaine Tomoho)
Maintenance information: 2026.5.23 Maintained (tone arm cleaning, PHONO cable connection pin cleaning, continuity check, height adjustment, sound output check)
Accessories: instruction manual copy (MA-505) secondary weight handle hex wrench
Main specifications: RX-2000 external dimensions W532 x H175 x D440 mm RY-3300 external dimensions W185 x H90 x D200 mm tone arm MA-505 dynamic balance type effective length: 237 mm needle pressure adjustment range 0 to 3 g compatible cartridge dead weight 13.5 to 19.5 g
※Only 1 tweeter 050ti GOLD is used for the L100 CENTURY GOLD. Excellent high frequency characteristics have been obtained due to pure titanium diaphragms and unique diamond edges. It is the same product as the 050Ti, but has been plated with 24K gold. There are wrinkles on the center cap. (FUJISAWA KOSHI)
Maintenance information: 2026.5.22 operation confirmed
Accessories: No accessories
Main specifications: 2.5 cm dome type 3 kHz to 30 kHz -6 dB input impedance 4 Ω screw pitch diagonal 11.5 mm diameter 130 x H30 mm 0.84 kg/piece (both measured)
Comes with original box! In addition to conventional MC/MM cartridges, this is a Soul Note all-in-one phono equalizer that can reproduce all types of cartridges compatible with DS Audio photoelectric cartridges. Uses the fully balanced non-feedback circuit of the signboard technology. The bold sound, where you can feel the extrusion and power, is irresistible. Made in 2023 Serial 230310008 (Fujisawa Yukishi)
Maintenance information: 2026.5.21 operation confirmed
Accessories: instruction manual, power cord, original box, spike, spanner
Main specifications: input sensitivity MC0.4mV, mm4mV, opt50mV gain MC72dB, mm52dB, opt30dB rated output voltage BALANCE2.8V, UNBALANCE 1.4V MC load resistance 3Ω/6Ω/12Ω/24Ω/40Ω/100Ω MM load capacity 100P/200P/350P W430 x H160 x D410 mm weight 21 kg
The price has been drastically reduced! 2026/5/17 sales price 798,000 yen This is the first time in stock in about 6 years! Comes with a stand! This is the British ATC mid-size monitor speaker SCM50P. The characteristic 7.5 cm soft dome mid-range has a strong sense of energy, and the strong, thick sound due to the strong enclosure are attractive. Small scratches can be seen throughout. ※ Since the main unit and stand are fixed, they cannot be removed. Serial 1597, 1598 (Fujisawa Yukishi)
Maintenance information: 2026.5.17 Operation confirmed
Accessories: stand, saran net
Main specifications: 3-way bass reflex type 24cm cone woofer 7.5cm dome type mid-range 2cm dome tweeter 8Ω 85dB size W304 ✕ H716 ✕ D400mm (main body, measurement) H967 mm (including stand, actual measurement) Weight 42.4 kg (including stand, actual measurement)
The price has been drastically reduced. 2026/5/6 sales price 478,000 yen Deteriorated parts including capacitors have been replaced and maintained! 220V specification (with 100V to 220V step-up transformer) with wood cab. A separate amplifier that is still popular even now, 70 years after its release. The thickness, luster, and tension of the sound are all emotionally composed, and perfectly express the sound of the instrument. Anyway, it is a famous machine with thick, firm mid-bass, and a tasteful sound unique to vacuum tubes. The exterior is oxidized on the volume knob, and there are text fragments (Mizusaki Ryo)
Maintenance information: 2026.5.3 maintained (◎ QUAD2 (common) · oil capacitor 0.1 μF deterioration replacement 3 x 2 · electrolytic capacitor 25 μF deterioration replacement x 2 · resistor 3W deterioration replacement 1 x 2 ◎ No. 36252 · vacuum tube KT66 damage replacement (it seems that it was broken into pieces during transportation. 2026.4.9 Supplies have arrived) ◎ QUAD22 · Filter selector hardening replacement · block capacitor 16 μF x 3 deterioration → replaced with 3 electrolytic capacitors · 0.5 μF other domestic products → replaced with European ones 4 · electrolytic capacitors 22 μF domestically produced → replaced with European products 4 · lamp defect replacement/resistance 1W deterioration replacement 4 · Radio1 only gang error improvement measures → 1/4 W resistor added 3 units* other with AC 220V Operation checked (measured at rated output 17W SP:8Ω) *KT66 1 glass shard is mixed in and makes a rattling sound, but operation is not affected)
Accessories: power cable, 220V step-up transformer
Main specifications: 17W (8Ω) with rated output AC220V [QUAD22] EF86 × 2 ECC83 × 2 input PHONO, RADIO, TAPE W267 × H89 × D148 mm 3.2 kg [QUAD2] KT66 × 4 EF86 × 2 GZ32 15W+15W W321 × H162 × D119 mm 8.2 kg/unit
The price has been drastically reduced. 2026/5/17 sales price 598,000 yen Maintenance has been completed, such as replacing 5 capacitors and 4 diodes, disassembling and repairing the power switch! Changed to Japanese specification 100V. A mono power amplifier for broadcasters developed at the North West German Broadcasting Center. The tone is quite thick, supple, and soft. It's a model I'd like to try with Old Tannoy, Quad ESL, Eurodyne, etc. There is rust and dullness over time (Oikawa Tetsuji)
Maintenance information: 2026.5.17 maintained (◎ common · selenium deterioration countermeasures → diode addition 2 x 2 · power switch disassembly repair · BIAS readjustment · HUM ADJ. readjustment · vacuum tube socket caulking repair ◎ 1 side · 100 μF x 2 liquid leak replacement 2 pieces · electrolytic capacitor 33 μF and others defective replacement and 3 additions
*Operation has also been checked with AC 100 to 110 V (rated output measured at 41 to 55 W SP: 4 ohms) *For BIAS adjustments at AC100V, please perform BIAS adjustments near the left end of the green line under the meter)
Accessories: none
Main specifications: F2A11 push-pull effective output 40w (8Ω) vacuum tube F2A11 x 2, EF804 x 2 W522 x H171 x D290 mm
*Rubber mats and subweights are missing. Hingeless 5th generation of the SL-1200 series. This is a high-grade model manufactured to commemorate the 30th anniversary. Its accuracy and durability are outstanding among many players, and it features clear sound with clear outlines. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.5.24 Operation confirmed
Accessories: copy of instruction manual, EP adapter
Main specifications: manual quartz direct drive 33/45 rotation universal S-shaped tone arm static balance type needle pressure adjustment range 0 to 4 g W453 x H162 x D353 mm 11.7 kg
*Rubber mats and subweights are missing. 5th generation of the SL-1200 series with hingeless specifications (metal fittings missing on one side). This is a high-grade model manufactured to commemorate the 30th anniversary. Its accuracy and durability are outstanding among many players, and it features clear sound with clear outlines. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.5.23 Operation confirmed
Accessories: copy of instruction manual, EP adapter
Main specifications: manual quartz direct drive 33/45 rotation universal S-shaped tone arm static balance type needle pressure adjustment range 0 to 4 g W453 x H162 x D353 mm 11.7 kg
RCA cable is a 1.5 m pair titanium-containing sheath boasting low loss/high Sn, an extra thick cable with the largest cross-sectional area in its class, and a basic, affordable RCA cable from Audio-Technica. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2026.5.25 continuity confirmed
Accessories: none
The price has been drastically reduced! 2026/5/17 sales price 148,000 yen beautiful item with box! Condenser-type ear speakers that focus not only on the amount of information, but also on the texture of the sound. The classical expression of the hall feeling is truly one word. Genuine leather is used for the part that comes into contact with the skin. There are no noticeable scratches and it is relatively good (Asae Tomoho)
Maintenance information: 2026.5.17 Operation confirmed
Accessories: original box
Main specifications: frequency characteristics 6 to 41,000 Hz impedance 170 kΩ sensitivity 100 dB standard bias voltage 580 VDC wide low capacity 6-core parallel cord length 2.5 m weight 365 g (recommended driver unit: SRM-007TA/SRM-727A, and other driver units equipped with STAX's 5-pin PRO bias can be used)
Famous machines are back! Thorough maintenance was carried out from the exterior to the interior, such as exchanging terminals. In addition to the sound quality, we are also concerned about the appearance, from the feel of the knobs, the texture of the wood grain, to the frame and screws. It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. It's been half a century since it went on sale, but the brillium diaphragm unit and precise cabinet, which have become rare in modern times, far from being comparable to other current speakers, stand out even more (Oikawa Tetsuji)
Maintenance information: 2026.4.27 Maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network maintenance: frequency characteristic check/ATT cleaning/terminal replacement, unit detachment)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 40 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 8 ohms output sound pressure level 90 dB dimensions W375 x H675 x D326 mm weight 31 kg/bottle
The price has been reduced. 2025/5/23 sales price 29,800 yen. TAOC's current speaker stand. Cast iron powder is sealed inside, and the top plate part has a double iron plate structure. It is a model where TAOC's vibration damping technology was fully demonstrated. The exterior has small scratches and dullness, etc., but it is generally good (Tomoho Asaine)
Accessories: spikes
Main specifications: Top plate dimensions W160 x D250 mm Bottom plate dimensions W250 x D350 mm H600 mm (including spikes) Weight 11 kg
The disposal price has been reduced. Member discounts are not applicable. 2026/5/12 sales price 79,800 yen*Cheap because spikes are out of stock. A tall boy speaker that combines KEF's standard coaxial unit with a double woofer. It has a very good balance from low to high frequencies, and also faithfully reproduces the subtle nuances of vocal songs. This model is very easy to integrate into a home theater. There are slight creases at the top and bottom corners of the exterior. There is a feeling of use on the saran net due to holes, fraying, dirt, etc. Serial QIQ9015412B53N8J QIQ9015467B53N8J (Murakoshi Yoichi)
Maintenance information: 2026.5.11 sound output confirmed
Accessories: saran net, jumper (general purpose)
Main specifications: impedance 8 ohms output sound pressure level 91 dB frequency characteristics 33 Hz to 40 kHz size W220 x H924 x D327 mm weight 16.3 kg
The price has been reduced. 2026/5/11 sales price 35,000 yen*Set of 8 The 2 pieces of felt are attached upside down. A TAOC speaker stand with a high vibration damping effect. Made from high-carbon cast iron, the speaker system improves pitch, depth, and transparency. Recommended for middle class speakers. Exterior, other emblems described above are missing, marks, dullness, abrasions, etc., and a feeling of use can be seen (Kobayashi Hitoshi)
Accessories: none
Main specifications: Uses high-carbon cast iron W100 x H140 x D170 mm, weight 5.0 kg
The disposal price has been reduced. Member discounts are not applicable. 2026/4/24 sales price 99,800 yen ※For commercial use, there is no guarantee and it will be delivered as is. Speaker with built-in amplifier. It sounds better than its size, and has crisp low frequencies and high frequencies that are smooth and not too thin. It was fine to play fusion, and guitar vocals, rock, etc. went well together. The ring part on the outer periphery of the unit is slightly sticky, and the meter lamp does not go out even when the display SW is turned off (Takasaki Atsushi)
Maintenance information: 2026.4.24 sound output confirmed
Accessories: power cord, manual CD
Main specifications: 10 inch LF driver, 1 inch titanium dome rear firing compression driver, coaxial design, 200W (LF) /200W (HF) power amplifier, approx. W381 x H381 x D381 mm, approx. 25 kg
Accuphase A grade premain. It was equipped with the “Balanced AAVA” volume control system that the C-3850, the top model of the preamp at the time, was equipped, and the resistance to external noise interference was greatly improved. As a result, the low frequencies can also be removed cleanly, making it extremely powerful. Smooth sound startup and deep reproduction of the sound field. This is one unit that boasts an amount of information that exceeds the boundaries of a pre-main amplifier (Kojima Yosuke)
Maintenance information: 2026.5.24 Operation confirmed
Accessories: remote control, instruction manual, power cable, original box
Main specifications: Class A drive rating continuous average output: 150 w/ch (1 Ω) 120 w/ch (2 Ω) 60 w/ch (4 Ω) 30 w/ch (8 Ω) frequency characteristics: 20 Hz to 20 kHz damping factor: 800 (8 50 Hz) load impedance: 2 to 16 ohms W465 × H191 × D428 mm 25.3 kg
Thorough maintenance has been carried out from polishing the contacts to replacing the deteriorated capacitors! ES Primaine's standard model. It is also equipped with a cartridge load selector, making it a perfect car for those who want to use it in a wide range of ways. The sound has momentum, and the thick sound is attractive. There are spots and small scratches on the exterior (Wang Zhan)
Maintenance information: 2026.5.21 Maintained (main volume dismantling and cleaning, phono selector, input selector, tape, tone, turnover, reck-out, muting, source direct, subsonic, etc.) Balance, tone volume sound wave cleaning Solder repair, pin jack polishing Replace the protector capacitor. (Interior and exterior inspection and cleaning, operation confirmation, running test)
Accessories: copy of instruction manual
Main specifications: 105W+105W (8Ω) PHONO input MM/MC compatible W470 x H161 x D436 mm 18.6 kg
This is a standard 5.0 m pair accuphase XLR cable with a balanced cable. Uses high-purity 7N copper wire. The plastic part at the base of the connector is cracked and defective. (FUJISAWA KOSHI)
Maintenance information: 2026.5.24 continuity confirmed
Accessories: No accessories
This is a standard 5.0 m pair accuphase XLR cable with a balanced cable. Uses high-purity 7N copper wire. The plastic part at the base of the connector is cracked and defective. (FUJISAWA KOSHI)
Maintenance information: 2026.5.24 continuity confirmed
Accessories: No accessories
This is a standard 3.0 m pair accuphase XLR cable with a balanced cable. Uses high-purity 7N copper wire. The sheath is slightly sticky, and the plastic part at the base of the connector is cracked and defective. (FUJISAWA KOSHI)
Maintenance information: 2026.5.24 continuity confirmed
Accessories: No accessories
This is a standard 3.0 m pair accuphase XLR cable with a balanced cable. Uses high-purity 7N copper wire. The sheath is slightly sticky, and the plastic part at the base of the connector is cracked and defective. (FUJISAWA KOSHI)
Maintenance information: 2026.5.24 continuity confirmed
Accessories: No accessories
This is a standard 3.0 m pair accuphase XLR cable with a balanced cable. Uses high-purity 7N copper wire. The sheath is slightly sticky, and the plastic part at the base of the connector is cracked and defective. (FUJISAWA KOSHI)
Maintenance information: 2026.5.24 continuity confirmed
Accessories: No accessories
This is a standard 2.0m pair accuphase XLR cable with a balanced cable. Uses high-purity 7N copper wire. The sheath is slightly sticky, and the plastic part at the base of the connector is cracked and defective. (FUJISAWA KOSHI)
Maintenance information: 2026.5.24 continuity confirmed
Accessories: No accessories
There is no problem with the operation, but since it is cheap, it will be handed over as is. Logitech PC speakers. Although it is a model for computers, it has passed the world standard THX standard for home theaters, so you can easily enjoy 2.1 channel sound. There is a feeling of use on the exterior due to small scratches etc. (Tomoho Asae)
Maintenance information: 2026.5.23 sound output confirmed
Accessories: none
Main specifications: 2.1 ch total output 200W (satellite 35W x 2, subwoofer 130W) 2 input systems (RCA, 3.5mm mini jack) satellite: 92 dB or more, subwoofer: 105 dB or more, 35 Hz to 20,000 Hz satellite section: W117 x H197 x D126 mm 1.9 kg/1 piece Subwoofer section: W305 x H284 x D266 mm 7 kg
An easy-to-use Orthophone MI cartridge with light needle pressure and high output. It has an accent in the mid to low range and is recommended for jazz and rock. There is dullness on the body (Kojima Yosuke)
Maintenance information: 2026.5.24 Operation confirmed (sound output OK. (Needle tip, cantilever, damper OK)
Accessories: none
Main specifications: MI type 5 mV optimal needle pressure 1 g playback frequency band 20-20,000 Hz load resistance 47 kΩ needle tip oval dead weight 5g
The price has been reduced! 2026/5/10 sales price 20,000 yen large insulator set of 4. The weight capacity is 60 kg, and the height can be adjusted by 7 mm. Please use it under the foot of a rotating device such as a record player. (FUJISAWA KOSHI)
Accessories: No accessories
Main specifications: load resistance 60 kg diameter 10 x height 50 mm weight 425 g per piece
The disposal price has been reduced! (Member prices are not applicable) 2026/5/11 sales price 1,200,000 yen Manufacturer maintenance completed in 2025! This is a crossfire preamp that follows the Cello ENCORE 1MΩ flow. The sound is innocent yet supple and nostalgic. It is a valuable car where you can experience the awesomeness of the infinitely neutral and transparent sound that VIOLA promotes without any coloring. *Gaps between VOL-30 and -20 remain, but the supply of repair parts has been discontinued, so this is the current situation. Serial 0266 (Fujisawa Yukishi)
Maintenance information: 2025.10.9 manufacturer maintained (attenuator re-adjusted. (There is still a gap between -30 and -20, but the supply of repair parts has been discontinued, so this is the current situation.) 2025.5.14 Manufacturer maintenance completed (volume contact cleaning, contact misalignment, contact float correction at specific contacts, shaft rotation misalignment VOL. Position correction)
Accessories: instruction manual, power cord, connection cord
Main specifications: fixed resistance switching type analog amplifier circuit module equipped with 4 output systems (XLR x 2, Fischer x 1, RCA x 1), 6 input systems (XLR x 1, Fischer x 1, RCA x 4) TAPE OUT (RCA x 1) main body W445 x H110 x D430 mm 9 kg power supply unit W225 x H110 x D400 mm 7.6 kg
The disposal price has been reduced. Member discounts are not applicable. 2026/5/9 sales price 448,000 yen Fully maintained, including replacement of deteriorated capacitors and resistors! The 220V specification (with 100V to 220V step-up transformer) is still popular even now, 70 years have passed since its release. The thickness, luster, and tension of the sound are all emotionally composed, and perfectly express the sound of the instrument. Anyway, it is a famous machine with thick, firm mid-bass, and a tasteful sound unique to vacuum tubes. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance Information: 2026.5.9 Maintained (QUAD2: Step Up Transformer Additional Block Capacitor 16 μF x 2 Hum Noise Replacement and Mounting Bracket Manufacture 1 x 2 Oil Capacitor 0.1 μF Deterioration Replacement x 2 Electrolytic Capacitor 22 μF Deterioration Replacement 1 x 2 x 2 Resistance 3W Deterioration Replacement 1 x 2 QUAD22: Vacuum Tube EF86 Replacement (2026.4.13 Supply Arrived) Adapter Missing 2 Block Capacitors Manufactured 16 μF x 3 → 3 additional electrolytic capacitors, 4 electrolytic capacitors, 22 μF deterioration replacement, 4 film capacitors, 0.1 μF, other deterioration exchanges, 2 resistors, 1 W and 1/2 W replacement, 8 gang error improvement measures → 1/4 W additional resistors, 5 AC plugs, additional vacuum tube socket and RCA jack caulking repair ※ Other operation check with AC 220V (rated output 13 W SP: 16 Ω wiring)
Accessories: power cable, copy of instruction manual, step-up transformer
Main specifications: 13W (16Ω) with rated output AC220V QUAD22: EF86 × 2 ECC83 × 2 input PHONO, RADIO, TAPE W267 × H89 × D148 mm 3.2 kg QUAD2: KT66 × 4 EF86 × 2 GZ32 15W+15W W321 × H162 × D119 mm 8.2 kg
The price has been reduced! 2026/5/22 sales price 278,000 yen Maintained! It is a 2+22 mono type. The analog EQ curve can be switched with a single button, perfect for mono recording enthusiasts. This is one that you want to play in combination with vintage speakers such as Tannoy and Altec. The nostalgic atmosphere you can't get on a modern aircraft is pleasant. The exterior has a feeling of wear over time, such as scratches and dullness. Serial 8275/73383 (Tomonori Asaine)
Maintenance information: 2026.5.22 maintained (Quad2 · step up transformer added · AC cord replaced with normal type · lamp defect exchange 3 · 0.1 μF deterioration exchange · 3 oil capacitors · 22 μF deterioration exchange · resistance 3W deterioration exchange · vacuum tube socket caulking repair QC2 · poor contact disassembly repair with each button · new manufacturing of oil capacitors 0.1 μF, etc. · 3 deterioration replacements · 22 μF electrolytic capacitors 4 other faults and deterioration replacements · 2 Mylar capacitors 1500 pF and other deterioration replacements · vacuum tube socket and RCA jack caulking repair ※ Other operation checked with AC230V (rated output 21W, measured at SP:8Ω) *Please press the 1 and 2 buttons on the radio 3 at the same time. Also, due to the structure of the selector, switching noise is high. ※The GZ32 guide pin of the rectifier tube is broken, but there is no problem with performance. Please be careful not to mismatch the position when inserting and inserting. (The rectifier tube and main body are marked in white)
Accessories: power cord step-up transformer
Main specifications: QUAD2 frequency characteristics 20 to 20,000 Hz input sensitivity 1.4 V signal-to-noise ratio 80 dB W313 x H165 x D106 mm weight approx. 9 kg QC2 line 2 systems, phono MM1 system W263 x H88 x D150 mm weight approx. 3 kg