Maintained! Original Model 7 You can enjoy a glossy mid to high range sound with a high sense of transparency and a thick, exquisite balance. It's a model that has been over half a century since it went on sale for analog fans, but it's still one they admire. The lustrous, indescribable tone is an appeal that cannot be enjoyed on modern devices. You can see a feeling of use, such as appearance, dullness, small scratches, etc. Serial 7-14836 (Kobayashi Hitoshi)
Maintenance information: 2023.5.20 maintained (balance volume B curve → MN curve replaced, block capacitor, 50 μF x 3, oil capacitor, 0.1 μF, other deterioration replacement, 8 electrolytic capacitors, 200 μF deterioration replacement, 2 vacuum tubes, 12AX7 deterioration replacement, 2 shield case replacement, high pressure selenium deterioration countermeasures → diode addition, side pad deterioration exchange, vacuum tube socket and RCA jack caulking repair, etc. Operation has been checked with AC 100 to 117 V)
Accessories: none
Main specifications: tubular control amplifier, vacuum tube, ECC83/12AX7, 3-stage NF equalizer, NF type step switching control, W453 x H185 x D267 mm, weight 7.5 kg
Transistors, capacitors, and many other parts have been replaced and refreshed and maintained! It was the highest-grade model at the time and had a vintage sound that overwhelmed the others, and by actively replacing deteriorated parts, the sound, which tends to be cloudy, has become clear, and the original momentum of the sound has been revived. It is particularly compatible with the JBL Lancer series back then. The exterior is dull, but it is in a good category even when viewed from the year it was released (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (capacitor, transistor, heat dissipation sheet, semi-fixed resistor, fuse replacement. SP terminal created. Various SW/VR internal cleaning. Clean each board contact. Solder again after removing the old solder. Internal and external cleaning, idle DC offset adjustment. (Audio output tested for various inputs and all SP terminals)
Accessories: copy of instruction manual
Main specifications: 80W+80W (8Ω) frequency characteristics 5Hz to 100kHz tone control/bass, midrange, treble 3-stage adjustment W462 x H155 x D316 mm 17.5 kg
The price has been drastically reduced. 2024/5/15 sales price 118,000 yen Maintained! A famous direct drive machine representative of Technics. The torque is high, the start and stop times are extremely short, and the stable operation that immediately enters constant speed is unique. It also drives LP heavyweights without difficulty. Overall there are small wounds, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (due to disconnection of the FG coil in the motor core, the FG/ angular velocity detection coil was taken out after disassembling the motor core, and the coil pack was rewound. The rotation speed has been reset)
Accessories: copy of instruction manual, power supply unit
Main specifications: Direct drive aluminum die-cast turntable 33, 45, 78 rotating body W365 x H100 x D360 mm 9.5 kg power supply unit W110 x H85 x D300 mm 3.8 kg
Maintained! A famous player that is still extremely popular even now, 20 years after its release. Despite its exceptional design and compact size, its sound quality is authentic, with thickness and depth unique to the heyday of CDs. It is a famous machine that is still highly popular today. The exterior is dull overall ※The remote control is out of stock (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (replaced and power supply resistor replaced due to FL tube drive IC failure. All operation switches have been replaced due to dust and dirt inside the main unit. Due to poor contact with the door opening/closing detection switch, the switch part was disassembled and the interior was polished and cleaned. Disassemble the SPDL motor, refill the bearing part with oil, and apply slide rail cleaning oil. (The optical system has been cleaned)
Accessories: instruction manual, stabilizer, power cable
Main specifications: frequency characteristics 2 Hz to 20 kHz terminal shape pin jack Coaxial digital output/coaxial connector optical digital output/optical output connector dimensions W280 x H90 x D370 mm weight 6.0 kg
All internal deteriorated capacitors and parts have been replaced! Furthermore, a new dust cover has also been created so you can use it comfortably. A masterpiece model of a semi-auto player. The torque and braking power of the motor are excellent, and the stability of operation is impressive. The sound quality, which is delicate and has an excellent sense of resolution, brings out the performance of the cartridge well. There are thin threads on the exterior. Serial 10700499 (Yonejima Satoshi)
Maintenance information: 2024.2.29 Maintained (new dust cover created, motor part removed, shaft and bearing cleaned and lubricated. The tact SW on the operation part and the electrolytic capacitor on the internal board were replaced with a new one. Resolder the board. Remove the area around the arm, clean each part after disassembly, replace the shaft bearing, inspect the internal lead wire, and reassemble. Dust cover hinge reinforcement bracket created. Exterior cleaning, cabinet scratch polishing, rotation speed check, operation test of each part, sound test)
Accessories: instruction manual, screws, EP adapter
Main Specifications: Quartz Lock DD Drive Auto Lift Up Static Balance Type Compatible Cartridge Weight 2 to 12 g Needle Pressure Range 0 to 3 g W490 x H182 x D410 mm 14.5 kg
M/MC compatible A tubular phono equalizer developed with the aim of better analog reproduction. You can enjoy a warm, natural sound using a vacuum tube non-feedback amplifier and a CR-type equalizer. The impedance can be switched according to the cartridge. Externally, there are line scratches on the top plate. Serial 00180 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: power cable
Main specifications: MM/MC compatible 12AX7 (ECC83) x 2 W300 x H100 x D260 mm 4.8 kg
The price has been drastically reduced! 2024/5/15 sales price 198,000 yen 800 Diamond series center speaker It is well connected to the Diamond Series due to unit groups that have evolved further from the previous game. High quality mid-range is reproduced. It is a cheap character that can be combined with other speakers for the center. There are thin threads on the exterior. Serial 12120002808 (Yonejima Satoshi)
Maintenance information: 2024.5.15 sweep test good
Accessories: jumper cable
Main specifications: 2-way bass reflex drive unit 25mm diamond dome tweeter x 1, 165mm Woben Kevlar cone FST mid woofer x 1 playback frequency band 42Hz to 33kHz output sound pressure level 88dB nominal impedance 8Ω W486 x H279 x D287 mm weight 12.5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/15 sales price 128,000 yen LINN network audio player with an integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1220444 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/15 sales price 128,000 yen LINN network audio player with an integrated amplifier. The built-in amplifier makes it easy to use, and you can easily enjoy network audio. It sounds soft and natural, and is perfect for those who want to enjoy music casually. As for the exterior, there are threads and dullness on the top plate. Serial 1234701 (Yonejima Satoshi)
Maintenance information: 2024.5.15 Operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible audio files FLAC, ALAC, WAV, AIFF, AAC, MP3 compatible sampling frequencies 7.35k, 8k, 11.025k, 12k, 14.7k, 16k, 22.05k, 24k, 29.4k, 32k, 44.1k, 48k, 88.2k, 96k176.4k, 192 k compatible bits 16 - 24 bit input terminal Ethernet analog audio RCA x 3 front AUX x 1 MM Phono digital audio coaxial RCA (SPDIF) x 3 TOSLINK (Optical) x 3 output terminal SP terminal 100W+100W W381 x H80 x D355 mm weight 5.0 kg
An XLR cable 0.6 m pair uses the world's most advanced virtual coaxial structure, and by using the same structure as a line cable as well as a microphone cable, it achieves low capacitance and broadband transmission (Satoshi Yonejima)
Maintenance information: 2024.5.15 continuity confirmed
Accessories: No accessories
*We were able to confirm the simple sound output, but since it is cheap, it is currently sold. A 2.1 channel (wireless subwoofer) system developed to match the company's Bravia X9000F series. The S-Force PRO front surround mechanism virtually creates a three-dimensional stereoscopic sound image without installing a rear speaker. The exterior is good, with a slight dullness (Kobayashi Hitoshi)
Maintenance information: 2024.5.13 Operation confirmed (video, remote control, simple BT sound)
Accessories: remote control, instruction manual, power cord, connection cord
Main specifications: 2.1 ch maximum power output 300W front 100W/100W subwoofer 100W size: bar speaker W930 x H58 x D85 mm 2.5 kg subwoofer W190 x H382 x D387 mm 7.8 kg
In January 2023, both the interior and exterior were maintained and brushed up! ORIGINAL LANSALOY EDGE! The OLYMPUS S8R representing JBL has arrived. The 075 tweeter is full of realism, with the sound of a driver blowing fire into the thick, dry low frequencies, and a sense of realism that leaves graininess. You can enjoy the real thrill of vintage audio. Outside of the exterior, the back plate on one side is missing, and the finish is beautiful due to maintenance (Kobayashi Hitoshi)
Maintenance information: 2023.1.10 maintenance (exterior repair, polishing, baffle/hakama repair before and after oil finishing, painting, lattice repair, polishing, painting, lining replacement. Woofer maintenance (edge softening treatment, corn paper coating, passive corn paper coating). Driver maintenance (magnetic circuit rust removal/gap cleaning/center adjustment, sound-absorbing material replacement, terminal contact cleaning). Tweeter maintenance (horn disassembly/polishing, magnetic circuit rust removal/gap cleaning, terminal contact cleaning). Network maintenance (LX5: terminal rust removal, acid washing, insulation bush & mounting screw replacement. ATT (SW type) disassembly contact polishing and cleaning. Reinforced with silicone to prevent the coil from coming off. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. N7000 terminal rust removal, acid cleaning, insulation bush, and mounting screw replacement. ATT replacement with a brand new one. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check input/output waveform and balance, check sound output))
Accessories: saran net, diffuser, instruction manual
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1020 x H670 x D510 mm weight 82 kg
Maintained! A power amplifier with a characteristic large meter. A straightforward tone with no peculiarities. There is momentum unique to the 80s, and you can enjoy crisp sound quality. It is also ideal as an introduction to separate amplifiers. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2024.5.14 maintained (output relay, meter relay replacement, indicator lamp replacement, meter lamp replacement, volume replacement, operational amplifier replacement, solder repair, interior and exterior inspection and cleaning, operation confirmation)
Accessories: copy of instruction manual
Main specifications: 130W+130W (8Ω) 170W+170W (4Ω) frequency characteristics 1Hz to 100kHz impedance 4Ω to 16Ω W450 × H174 × D422mm 18.5 kg
*Currently sold. Details of Sony's 15 cm full range unit pair are unknown, but there is a description of i-502-437-11 on the back. I was able to sweep and make a sound. The exterior has dullness, stains, etc. (Tomoho Asaine)
Maintenance information: 2024.5.14 sound output confirmed
Accessories: none
*Currently sold. Details of only one Sony 15 cm full range unit are unknown, but there is an I-502-437-11 description on the back. I was able to sweep and make a sound. The exterior has dullness, stains, etc. (Tomoho Asaine)
Maintenance information: 2024.5.14 sound output confirmed
Accessories: none
The price has been drastically reduced. 2024/5/14 sales price 158,000 yen The top plate has line damage, so it's cheap. Genuine Rin Japan A famous player that brought network audio to the world at a high level. Equipped with the same functions as the KLIMAX DS, such as balanced output. The density of sound and the rich amount of information are attractive. The remote control is LINN's general-purpose type (Oikawa Tetsuji)
Maintenance information: 2024.5.14 operation confirmed (PCM/playback up to 192 kHz OK)
Accessories: power cable, universal remote control
Main specifications: support files FLAC, WAV, AIFF, AAC, MP3, WMA W381 x D360 x H80 mm 4.0 kg
The price has been drastically reduced! 2024/5/14 Torrens entry model with sales price 118,000 yen. Although it is an entry model, the silence and smoothness of the belt drive, and the delicate sound are attractive, and the tone arm is easy to adjust. Recommended for introductory belt drive machines. There are a few small scratches on the exterior. Serial 00262803 (Fujisawa Yukishi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: copy of instruction manual, power cord, connection cord, spike base, original box
Main specifications: W420 x H125 x D330 mm 8 kg Drive system: belt drive motor: synchronous motor speed: 33 1/3, 45 rpm electronic speed selection platter: diameter 300 mm, 3 kg, aluminum power supply unit housing tone arm: static balance type
Over 300 deteriorated parts, including 133 transistors and 65 capacitors, have been replaced and maintained! Shell (AT-LH15/OCC) with cartridge (AT-F3/2). A supreme record player made by combining the best of Yamaha's engineering. In addition to adopting a linear tracking system, what is surprising is the amount of material that was put in without hesitation. The total weight of the main body alone is 27 kg, and the turntable made of super duralumin cut from solid wood weighs 5.6 kg. The well-structured low range and the delicate, clean sound that spans the entire range are remarkable. The smooth operation feeling of auto play and multifunctionality such as pitch control are also attractive. There are small scratches and dullness, but it is a beautiful category even when viewed from the model year (Oikawa Tetsuji)
Maintenance information: 2024.5.14 Maintained (replacement of deteriorated parts, re-soldering of each board, board cleaning, volume disassembly cleaning, circuit adjustment of each part, operation check, sound test)
Accessories: power supply unit, screw, shell (AT-LH15/OCC), cartridge (AT-F3/2)
Main specifications: Direct drive system motor 20 pole 15 winding slotless DC motor tone arm/dynamic balance linear tracking arm mounting cartridge dead weight range 4 to 13 g rated power consumption 27 W body/W480 x H154 x D416 mm 27 kg power supply/W124 x H90 x D385 mm 5 kg
Maintained by the manufacturer. The third generation of the Denon 2000 series. Frequency characteristics have been improved and low noise has been achieved by reviewing power parts, volume circuits, etc., while keeping the low frequency range with a sense of volume unique to the company and the high frequency range with elongation unchanged. Of course, it is a big hit model that is compatible with modern sauces, and doesn't make you feel that it's poor to listen to old sources. There are abrasions on the exterior and volume, and dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 manufacturer maintained (1 PSW rework, 12V relay, function SW replacement. (Amplifier board inspection, solder correction, operation confirmation test)
Accessories: instruction manual, power cord
Main specifications: output 80W+80W (8Ω) PHONO (MM/MC) bi-wiring compatible W434 x H180 x D478 mm 22 kg
Maintained! 15th anniversary model of the 607 series. MOS-FET is used for the power stage, adding a sense of transparency to its characteristic heat, and is compatible with various music genres. It has a configuration that exceeds its class, such as balanced input support, and it is a powerful machine that is still popular today. You can see a feeling of use, such as appearance, dullness, small scratches, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 maintenance completed (tone and other switches dismantled and polished, coated with grease (loudness, muting, processor, subsonic, input selector, power amplifier direct, source direct switch), output relay replacement, protector part capacitor replacement, solder repair, internal inspection and cleaning, bottom repair, operation confirmation)
Accessories: power cable, copy of manual
Main specifications: 45W+45W (8Ω) PHONO (MM/MC) W460 × H159 × D446mm 18.8 kg
Maintained by the manufacturer! A special edition model of VRDS-10. This is the only TEAC player model that uses a Philips TDA1547 as a D/A converter. The sound quality is not sharp due to the hardware of VRDS, and the sound quality is well-balanced, which brings out the characteristics of the relaxed DAC7. In addition to being able to see many scratches on the exterior and top plate and abrasions on the front panel, there is dullness and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.14 manufacturer maintained (flat cable adjustment) 2024.4.13 manufacturer maintained (belt replacement, deteriorated parts replacement, inspection and adjustment of various parts)
Accessories: remote control, copy of instruction manual, lock key
Main specifications: 2-channel CD player frequency characteristics 1 Hz to 20 kHz 8 times oversampling 20 bit digital filter W442 x H149 x D331 mm 11 kg
*Currently sold. A small Yamaha speaker with a piano finish. Rich bass reproduction is achieved by deepening the depth while being small. Deep low frequencies are added to the sharp, stretchy mid-high range unique to Yamaha, so you can enjoy sound that's more than the price. There are scuffs and dents on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.14 sound output confirmed
Accessories: saran net
Main specifications: output sound pressure level 85dB impedance 6Ω allowable input 40W playback frequency band 55Hz to 80kHz W154 x H274 x D287 mm weight 3.9 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/13 sales price 30,000 yen model number, convenient for small amplifiers, etc. such as unspecified steel satin finish audio racks, spike specification LINN products, etc. There is a feeling of use on the exterior such as small scratches and dullness (Asaine Tomoho)
Accessories: none
Main specifications: size W395 x H540 x D395 mm shelf board 350 x 350 mm between shelves 105 mm weight 11.7 kg (actual measurement)
The price has been reduced! 2024/5/13 sales price 84,800 yen ※The rubber on the saran net cloth cover is fully stretched, so it's cheap! LINN tall boy speaker. It is a speaker with a relaxed, mature sound like a circle, and the more you listen to it without decoration, the more delicious it is. There is a feeling of use on the exterior due to scratches, dullness, etc. ※The active module is not included. Serial 004963 004964 (Tomonori Asaine)
Maintenance information: 2024.5.13 sweep test is good
Accessories: Saran net cloth cover
Main specifications: 3 way 8 ohm maximum input 75 W crossover 2.5 kHz efficiency 87 db W 192 x H900 x D 280 mm 25 kg/book
The price has been drastically reduced! 2024/5/13 sales price 108,000 yen Speaker from Taiwanese manufacturer Usher Audio with a unique design. The mid to high frequencies are delicate and stretchy, and the low frequencies have an attractive, bouncy, and tense sound. It is a model that works very well with current pop and piano sounds when played clearly with a powerful amplifier. There is a feeling of use on the exterior such as small scratches and dullness (Asaine Tomoho)
Maintenance information: 2024.5.13 operation confirmed
Accessories: Saran net spike spike receiving jumper plate
Main specifications: 3-way 3-speaker bi-wire specification 8Ω 87dB 25Hz to 28,000 Hz W350 x H1250 x D650 mm 58.2 kg
※Chips and oxidation are conspicuous in the horn part, so it is inexpensive. A tweeter representing JBL. It gives an expression with a greater sense of depth and breadth than 075. It has a punchy, dynamic sound quality, and is a model unique to this era that excelled in characteristics such as a sense of attack and horsepower. The exterior has dullness, rust, and scratches due to aging. Serial 33996/33998 (Yonejima Satoshi)
Maintenance information: 2024.5.13 good oscillator test
Accessories: No accessories
Main specifications: horn type ferrite magnet playback frequency band 2,500 to 15,000 Hz impedance 8 ohms output sound pressure level 110 dB diameter 119 x depth 94 mm weight 2.4 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/5/13 Tall Boy with a sales price of 148,000 yen. The woofer uses a wood fiber cone, and the tweeter is equipped with a 28mm dome tweeter and ribbon tweeter. In addition to the conventional mid-high range with a high texture, we have acquired a new low range where you can feel the high response. Serial 1917336 (Murakoshi Yoichi)
Maintenance information: 2024.5.13 sound output confirmed
Accessories: saran net, jumper cable, spikes, metal fittings
Main specifications: 3 way 4 speakers bass reflex type frequency characteristics 49 Hz to 32 kHz efficiency 89 dB impedance 4 ohms W195 x H001 x D330 mm weight 18.9 kg
Maintained! A power amplifier using the AB/LR independent power supply system, which is a further development of the A class B class 2 independent power supply system. Contrary to its solid appearance, it has a beautiful sound with a sense of transparency. The sound quality is moderately tight and firm, and it naturally handles crisp and energetic intonation expressions. The exterior has small scratches and dullness appropriate for the model year (Oikawa Tetsuji)
Maintenance information: 2024.5.12 Maintained (replacement of defective output relay contacts. (Replace deteriorated capacitors in power supply circuits and other circuits)
Accessories: none
Main specifications: 100W+100W (8Ω) compatible speakers 4Ω to 16Ω SNR 110dB W420 x H166.5 x D300 mm 19.2 kg
Maintained! The dust cover is hingeless. A classic record player that Technics is proud of. It is attractive for its simple design, stable operation, and outstanding durability. This model is recommended as an introductory model and as a secondary unit. There is a feeling of use (Daiki Goto)
Maintenance information: 2024.5.13 Maintained (by disassembling the upper and lower mechanism of the arm, wipe off the stuck grease and apply new grease and reassemble. There were no other operation or sound inspection abnormalities.)
Accessories: EP adapter
Main specifications: quartz lock direct drive, full manual type, 33/45 rotation, adjustable pitch control, W453 x H360 x D162 mm, 12 kg
Mono exclusive MC cartridge. It's not flashy, but it stretches and makes a gentle sound that is pleasant. There is a feeling of use such as dullness (Daiki Goto)
Maintenance information: 2024.5.13 operation confirmed
Accessories: original box, instruction manual
Main specifications: MC type 0.5 mV needle pressure 2.5 to 4.5 g dead weight 5 g
The disposal price has been reduced (member prices are not applicable). 2024/5/12 reprint model of the famous MINIMA with a sales price of 298,000 yen. The unique expanse and colorful sound transcends the boundaries of compact speakers. If you set it slightly away from the wall, a deep sound field space will be drawn. The beautiful wood grain and good texture are also attractive. There are small scratches on the side etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.12 operation confirmed
Accessories: instruction manual, cover
Main specifications: 2-way speaker bass reflex type frequency characteristics 55 Hz to 25 kHz impedance 8 ohms output sound pressure level 84 dB W200 x H330 x D275 mm weight 6.9 kg
The disposal price has been reduced (member prices are not applicable). 2024/5/12 sales price 148,000 yen B&W middle class “tweeter on top” model from the new commercial series. You can enjoy high-response sounds and vivid and realistic spatial expressions. The exterior has scratches, line wounds, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.12 operation confirmed
Accessories: instruction manual
Main specifications: 8Ω 88dB 45Hz to 50kHz W200 × H403 × D301 mm weight 8.9 kg
Balance cable, 0.7 m pair, PC-Triple C conductor, conductor with stable electrical characteristics such as ultra-low distortion ratio and high conductivity, and double shielding for perfect noise countermeasures. It has an edgy, well-cut sound using a gold plated plug made by Neutrik. The lettering is frayed and thinned. (FUJISAWA KOSHI)
Maintenance information: 2024.5.12 continuity confirmed
Accessories: No accessories
Power cable 1.2m Power cable using the original precision conductor “102SSC”. A cable with a strong monitor color that clearly reproduces music. Recommended for connecting to professional audio devices. (FUJISAWA KOSHI)
Maintenance information: 2024.5.12 continuity confirmed
Accessories: original box
The A3500 vacuum tube power amplifier has been refreshed by thorough maintenance down to the smallest details, such as volume disassembly and polishing. The warm, fresh tone, filled with the appeal of a vacuum tube type, is still appealing enough today. You can enjoy music with a rich, thick tone that contrasts with the clicking tones of recent vacuum tube amplifiers. As for the exterior, paint deterioration and peeling can be seen on the transformer on one side, and there is a feeling of use such as dullness, small scratches, etc., and there is a dent in the hood. ※3-pole tube connection specification. 20W+20W (actual measurement) is output as specified by the manufacturer (Takasaki Atsushi)
Maintenance information: 2023.2.3 maintained (main tube (6CA7) replacement vacuum tube socket, block capacitor, electrolytic capacitor, oil capacitor, SP and RCA terminals, complete disassembly of semi-fixed VR replacement power input gain volume, contact polishing, anti-oxidation/sulfation grease coating load test (8Ω load 1kHz 20W+20W) input/output waveform confirmation sound output check performed)
Accessories: copy of the manual
Main specifications: 20W+20W (8Ω) vacuum tube 6CA7×4/6AQ8×3 W465×H168×D206mm 16kg
Maintained by the manufacturer! The 3rd generation model of the S10 series. Equipped with AL24 Processing, an analog waveform reproduction technology. The degree of perfection of the sound is extremely high, and in addition to the heavy mid-low range, the music is pleasantly enjoyable with colorful tones unique to Denon. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 1021503089 (Yamato Yuki)
Maintenance information: 2024.4.22 Maintained (current laser pickup level is within regulations, but if it breaks down in the future, pickups cannot be obtained. Loading belt tray opening/closing SW replacement sound test)
Accessories: instruction manual copy remote control power cable
Main specifications: 24bit/96kHz alpha processor, HDCD decoder with DA converter function (coaxial/optical switching), W430 x H130 x D330 mm, 14 kg
A new standard model for the SL-1200 series, inheriting the efforts and results that began with the development of the SL-1200G. Outstanding reliability and stability are now available at an affordable price. I'm also happy that it is compatible with 78 revolutions. There is a thread on the dust cover on the exterior (Satoshi Yonejima)
Maintenance information: 2024.5.12 Operation confirmed.
Accessories: power cord, connection cord, EP adapter, weight sold separately, original box
Main Specifications: Direct Drive Turntable System Brushless DC Motor Speed 33 1/3, 45, 78 Universal S-shaped Tone Arm Static Balance Needle Pressure Adjustment Range 0 to 4 g Applicable Cartridge Weight/5.6 to 12.0 g, 14.3 to 20.7 g (including headshell) /when using auxiliary weight/10.0 to 16.4 g, 18.7 to 25.1 g (headshell included) W453 mm x H173 mm x D372 mm approx. 11.5 kg
DENON analog player. It is a model that is easy to use and has excellent cost performance. The phono cable is detachable and can be replaced with a cable of your choice. This model is also suitable for introductory use. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.12 Operation confirmed
Accessories: connecting cable, adapter, dust cover
Main specifications: quartz servo type direct drive speed 33 1/3 rpm, 45 rpm static balance S-shaped pipe arm needle pressure adjustment range 0 to 4.0 g compatible cartridge weight 14.0 to 20.0 g W450 x H170 x D370 mm 10.1 kg
There is a well-balanced connection between all bands and a good sense of localization, and the three-dimensional grasp of sound is simple and can be reproduced with high quality. I think the AV settings are good along with the other Platinum series, but I think you can enjoy it with 2CH regardless of genre. There are 2 dents on the exterior and top plate, and a feeling of use can be seen such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.5.10 Operation confirmed
Accessories: zipper cross grill
Main Specifications: Input 20-150W Allowable Input (RMS) 75W Maximum Allowable Input (Instantaneous) 300W Efficiency 87dB (1W/1m) Impedance 8Ω Frequency Characteristics 40Hz to 20kHz (-6dB) LF (Woofer) 165 mm (6.5 inch), Multi-fiber Paper Cone MF (Mid) 165 mm (6.5 inch) HF (Tweeter) 25.4 mm (1 inch) Silk Dome Tweeter Crossover Type 3 Way, low loss passive type, hardwired crossover frequency 350Hz, 2.5kHz enclosure type bass reflex W235×H1,078×D300mm 17.1 kg
The price has been drastically reduced! 2024/5/11 sales price 128,000 yen Maintained! Late QUAD44 with CD input terminal. It's not flashy, but the thick, glossy tone is attractive. In particular, it softens female vocals. Serial Q36114 (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (internal power supply switch contact dirt contact polishing treatment, balance VOL cleaning ~ check OK. Check the other boards and re-solder the holes. C, R check OK)
2024.5.9 Internal power supply switch contact polishing treatment
Accessories: power cord
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321 x H103 x D203 mm, 4.0 kg
Both the interior and exterior have been fully restored and refreshed! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. It is beautiful due to exterior repairs (Sasaki Shota)
Maintenance information: 2024.5.10 Maintained (exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting. Saran net replacement/frame repair/reinforcement. Unit maintenance: low range/edge exchange, magnetic circuit gap cleaning/center adjustment, high pass/magnetic circuit rust removal/gap cleaning/center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, faston terminal replacement, terminal cleaning)
Accessories: none
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
YAMAHA's heavyweight premain amplifier. The low frequency with good damping by a good power transformer and the clear sound typical of YAMAHA are attractive. The PHONO input is equipped with MC, making it a great specification for analog fans. The pre-main part can be separated, and there is potential for development into a separate part. There are a lot of front panel stains on the exterior. There is deterioration on the back side of the wood panel (Sasaki Shota)
Maintenance information: 2024.5.11 Maintained (right amplifier power circuit fault repair. Soldering correction in each circuit, including the left and right main amplifiers. Disassemble the switch and polish the contacts and apply contact cleaner. Bad output relay contact replacement. Knob installation correction. (I/O pin jack polish)
Accessories: copy of the manual
Main specifications: 130W+130W (8Ω) 150W+150W (6Ω) PHONO (MM/MC) pre-main separable W473 x H169 x D464 mm 26 kg
Maintained! The strength of the extrusion of the entire range and the clear sound are truly sounds unique to the heyday of JBL. The mid-high range with a unique sense of spaciousness and strong linearity makes hard bop and trumpet sounds pleasant. The sense of volume in the mid to low range is also attractive not found in modern speakers. The exterior has been beautifully finished due to maintenance (Mizusaki Ryo)
Maintenance information: 2024.5.11 maintained (exterior repair/polishing/oil finish, front and rear baffle/horn repair/painting, saran net replacement/frame repair, woofer edge replacement, driver maintenance: magnetic circuit rust removal/gap cleaning/center adjustment, network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/screw replacement, unit detachment)
Accessories: saran net
Main specifications: 2-way bass reflex, 30cm woofer, frequency band, 40Hz to 16kHz, impedance, 8Ω, sound pressure level, 91 dB, dimensions W406 x H635 x D311 mm, weight 26 kg/book
Refresh yourself with internal and external maintenance! This is an attractive mid-size model with the large 38cm HPD385 unit pressed into a compact enclosure. It has good phase characteristics and plays classical music and vocals in a pleasant tone with a high texture and a good, moist tone (Mizusaki Ryo)
Maintenance information: 2024.5.11 Maintained (exterior repair/cleaning
unit assembly)
2019.12.30 Maintained (input terminal rust removal (pickling) treatment, cleaning. Internal connection terminal (faston) replaced with a new one. Output terminal polish cleaning. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Exterior repair/polishing/oil finish. Front and rear baffle/hakama paint Saran net replacement. Unit maintenance (low range side: edge exchange, magnetic circuit gap cleaning center adjustment, high range side: magnetic circuit gap cleaning center adjustment) unit detachment)
Accessories: none
Main specifications: coaxial 2-way speaker, front bass reflex system, 8Ω, 91 dB, W540 x H840 x D310 mm, 32 kg
The disposal price has been reduced (member prices are not applicable). 2024/5/15 sales price 298,000 yen Orthophone Japan has been maintained! One owner item! It is a system equipped with the company's WTB-211 tonearm. The sound quality created by the wooden base and heavyweight metal turntable is a player that achieves well-balanced sound quality from low to high frequencies. It is a system that can be used stably without the need for frequency conversion (pulley), and allows you to fully sense not only the MM needle, but also the delicate nuances of the MC needle (Oikawa Tetsuji)
Maintenance information: Maintained by 2024.5.11 Orthophone (bearing replacement, correction process, operation confirmed)
Accessories: power cable, strobe, instruction manual
Main specifications: thread drive speed 45/33 W 470 x H250 x D370 mm 35.5 kg tone arm execution length 229 mm effective length 214 mm overhang 15 mm compatible cartridge weight 18 g to 26 g (shell cartridge included)
The price has been reduced! 2023/5/11 sales price 49,800 yen ※Since manufacturer repairs are not possible, it will be sold as is. The remote control is now in stock. It is a compact premain amplifier equipped with plenty of inputs in a 214mm half-size housing. Compatible with a total of 3 digital inputs, 1 optical 2 coaxial, USB input up to 192 kHz/24 bit, and Bluetooth audio transmission. It is compatible with all kinds of music sources. The exterior is dull. Serial 53330E001473 (Yonejima Satoshi)
Maintenance information: 2024.5.9 operation confirmed
Accessories: instruction manual (English characters), power cord, remote control
Main specifications: output 80W x 2ch (4Ω) output terminal subwoofer x 1/headphone x 1/input terminal LINE x 2/COAXIAL x 1/OPTICAL x 2/USB x 1 digital input USB maximum 192 kHz/24 bit COAX/OPTICAL maximum 192 kHz/24 bit other Bluetooth audio compatible (A2DP with aptX) W214 x H60 x D284 mm mass 2.8 kg
Full maintenance, such as internal and external maintenance, was carried out, and the finish was beautiful! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. Serial 55553L, 55553R (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (exterior repair/repaint) 2017.4.25 Maintained (exterior polishing/all coated woofer cone paper/unit frame paint chip putty repair grill dent correction/paint tweeter distortion and maintenance (edge deformation repair, magnetic circuit slit maintenance complete) unit detachment terminal replacement (banana plug compatible product) ATT cleaning capacitor replacement*Some capacitors before replacement Since it is difficult to remove, remove the wiring to check the remaining input/output waveform and balance, sound output check, frequency characteristic measurement check (~ 42 kHz)
Accessories: No accessories
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
Both the interior and exterior have been maintained and brushed up! The OLYMPUS S8R representing JBL has arrived. The combination of thick, dry low frequencies, the sound of a driver that seems to blow fire, and the 075, which leaves a gritty feeling of realism, is impressive. Please enjoy the real thrill of vintage audio. The exterior is also beautifully finished (Yonejima Satoshi)
Maintenance information: 2024.5.11 Maintained (network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning/screw replacement, exterior cleaning. Woofer maintenance: edge replacement, cone paper coating, passive cone paper coating. Exterior repair/polishing/oil finish, front and rear baffle/hakama repair/painting. Lattice repair/polishing/painting, lining replacement. (Detaching the unit, repairing the diffuser)
Accessories: saran net
Main specifications: 3-way 3-speaker passive radiator system low range unit 38cm cone type (LE15A) mid range unit horn type (375) high range unit (075) passive radiator 38cm cone type (PR15) network LX5/N7000 sound pressure level 95dB allowable input 125W dimensions W1,020 x H670 x D510 mm weight 82 kg
The exterior has been fully restored, edge replaced, and network maintained! This speaker was introduced as a successor to the Arden, but the width has been drastically cut, and the finish is moderately sized and easy to use. The tunings organized in the middle range make me feel comfortable listening to vocals and violin. The exterior has a beautiful finish. Serial 002563/002668 (Yonejima Satoshi)
Maintenance information: 2024.5.11 Maintained (unit maintenance: low range side: edge replacement, magnetic circuit gap cleaning center adjustment, high range side: magnetic circuit gap cleaning center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, faston terminal replacement, terminal cleaning, exterior repair/polishing/oil finish, front and rear baffle/hakama repair/painting, saran net replacement)
Accessories: saran net
Main specifications: used unit 3839/15 inch coaxial 2 way 120W 113 dB 8 ohm dimensions W498 x H1,000 x D489 mm weight 46 kg
Internally and externally maintained! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. There is a very slight dent in the tweeter grill, and there are repair marks on the side (Murakoshi Yoichi)
Maintenance information: 2024.3.4 maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network frequency characteristic check, ATT cleaning, terminal replacement)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle