The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg
※1 bottle only. Maintained! This is a rare blue frame (above) model LX5. The impedance is 8 ohms, and the cross is 500 Hz, so be sure to use a 175 or 375 driver that uses 8 ohms! There are spots, rust spots, and small scratches. (Honda Maki)
Maintenance information: 2021.12.21 Conductivity confirmed 2019.4.4 Maintained (re-fix the internal coil with silicone agent. Remove rust from terminals and mounting screws, clean, and tighten. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: No accessories
Key Specifications: Crossover Frequency: 500 Hz Level Control: 3 Position Switch Input Impedance: 16 ohms 159 x 153 x 120 mm 2.3 kg
The price has been drastically reduced. 2023/9/9 sales price 69,800 yen*The diaphragm has been replaced with a D8R2421, and the label on one side is missing, so it's cheap. Maintained! Representative of JBL's 1-inch driver units. The playback band is wide, so you can enjoy changing the network cross freely. The toughness, sound pressure, and full-bodied mid-high range sound are appealing, which is unbelievable for some input. There are small scratches and paint peeling (Oikawa Tetsuji)
Maintenance information: 2023.9.9 maintained (diaphragm installation adjustment (vibration plate is equipped with D8R2421)
Accessories: none
Main specifications: 1 inch driver, 500 to 20,000 Hz, 8 ohms, W145 x D97 mm, 5.1 kg/bottle
2023.12.18Maintained professional cross 800Hz network. It is used in the 4320, etc., and the low frequencies are pushed out smoothly, giving the impression that the clarity of the mid-high range has improved. This network is useful for creating 2-way systems where woofers have a certain amount of area. How about making a 2-way horn system with a 16Ω unit? There are stains and rust on the main body. (TERAMOTO Hidehiko)
Maintenance information: 2023.12.18 Maintained (terminal rust removal treatment, cleaning, mounting screw replacement. SW type ATT contact cleaning. Frequency characteristics are measured and checked, and the original capacitors are continuously used for good results. (Check the input/output waveform and balance, check the sound output)
Main specifications: crossover frequency 800 Hz impedance 12 to 16 ohms W122 x H154 x D132 mm 1.9 kg/1 unit
※This item is currently sold. Onkyo enabled speaker. It is a design that makes it possible to construct a Dolby Atmos sound field using sound reflection from the ceiling. Accessories such as brackets and cables are missing (Sasaki Shota)
Maintenance Information: 2023.12.11 Sweep Test Good
Accessories: none
Main specifications: sealed impedance 6 ohms, playback frequency band 90 Hz to 20 kHz, W120 x H155 x D153 mm, 1.2 kg
A classic MC boost transformer. With 2 input systems, an impedance of 3.40 ohms switchable, and a PASS line, you can freely enjoy a variety of cartridges and tone arms. There is an appearance, dullness, and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.11.18 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input, 2 systems, switchable, 1st order impedance 40 Ω, 3 Ω, switching, 2nd order impedance 4 kΩ, boost ratio 1:10, frequency characteristics, 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
The price has been reduced. 2023/10/6 sales price 29,800 yen ※Since it is only 1 bottle, it is cheap. JBL professional 2" screwdriver. It is an item that continues to be used in large horn systems, etc. The quality unique to titanium diaphragms, the breathing of the vocals, and the high hat on the drums are all appealing, and the outstanding realism is appealing. The exterior has dullness, dirt, and scratches. Serial 31316 (Tamura Eiji)
Maintenance Information: 2023.10.6 Oscillator Test Good
Accessories: no accessories
Main specifications: slot diameter 5 cm, allowable input 100 W, sound pressure level 111 dB/W/m, frequency characteristics, 500 Hz to 20 kHz, crossover frequency, 500 Hz or more, 16 ohms, diameter 235 x depth 132 mm, 13.6 kg/1
The price has been reduced. 2023/9/22 Sales price 69,800 yen ※Since this is a remodeled product, it is currently sold. 3-way network. The details of the crossover are unknown. The attenuator comes with FOSTEX's AT-50H (16 ohms for the middle range only). There is a slight creak, but the sound output has been confirmed. I even took pictures of the interior. Please refer to it. There is no original terminal block (Sasaki Shota)
Maintenance information: 2023.9.22 sound output confirmed
Accessories: none
Main specifications: 3-way network W210 x H235 x D158 mm 4.5 kg (actual measurement)
Line matching transformer sold 1 piece Primary: 600 Ω - CT Secondary: 600 ohms Output 10 dBm Frequency Range 50 to 10 kHz W44 x H65 mm 0.25 kg/piece There are bumps and paint peeling in places (Yosuke Kojima)
Accessories: none
* Since there are difficulties with the attachment part on both sides, it is inexpensive. Line matching transformer sold primary: 600 ohms, output 10 dBm, frequency range, 50 to 10 kHz, W44 x H65 mm, 0.25 kg/piece, the head of the mounting bolt on one side is flying off, and there is distortion in the screw hole on the other side (Kojima Yosuke)
Accessories: none
* It seems to be an output transformer from the specifications; sold 1 piece, primary: 10 kΩ, secondary: 600 ohms, W76 x H71 x D43 mm, 0.6 kg (actual measurement, not including protrusions), there is paint peeling in places (Kojima Yosuke)
Accessories: none
※Since it is inexpensive, it will be handed over as is. Tamban 10cm full range unit. An ultra-thin PP diaphragm with reinforced ribs is used. The sound is clear and crisp. A 6-8 liter bass reflex box is recommended (Tamura Eiji)
Maintenance information: 2023.10.1 sweep check OK
Accessories: none
Main Specifications: Rubber Edge Impedance 4 Ohms Sound Pressure Level 87 dB Frequency Band 63 to 17,000 Hz Maximum Input 40 W Baffle Aperture Diameter 94 mm Weight 380 g
Output transparent pair for push-pull output 40W primary: 10 kΩ secondary: 4-8-16 ohms Usage: VT-62, VT-25, 6F6, 6V6, etc. W83 x H105 x D78 mm approx. 2.3 kg/piece (actual measurement, not including protrusions) with original box with scuffs and tape marks in places (Kojima Yosuke)
Accessories: original box
Disposal prices have been reduced! (Member discounts are not applicable) 2023/2/5 sales price 10,000 yen ※1 bottle only. DynAudio's classic 17cm cone woofer. It has resolution and is recommended for bookshelves, etc. The urethane on the back magnet side has not deteriorated (Tamura Eiji)
Maintenance information: 2023.2.5 good sweep test
Accessories: There are no accessories
Main specifications: 17 cm cone type impedance 4 ohms diameter 176 mm depth 66.5 mm
※1 bottle only. This is a 10 cm full range unit from FOSTEX. It is a very popular model for those who make their own speakers. The sound quality is bright and has an impression of tension. Dull, there is a feeling of use (Sasaki Shota)
Maintenance information: 2023.8.11 sound output tested
Accessories: manual, original box
Main specifications: full range aperture 10 cm maximum input 15 W 8 ohms magnetic flux density 13000 gauss baffle aperture diameter 9 cm recommended enclosure volume 15 L
Since the condition is poor, such as cracks in the body, it is currently being sold. A small full-range speaker that is compact, can be placed freely, and has a gentle impression. The sound quality is soft and the sound is relaxed. You can see a feeling of use such as cracks, dullness, and abrasions on the exterior and body (Kobayashi Hitoshi)
Maintenance Information:2023.6.5 Operation confirmed
Accessories: none
Main specifications: full range compact speaker 8ohm maximum input 40W W230 x H150 x D163 mm 1.6 kg
Maintained in October 2022! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, paint is bald and oxidized (Yonejima Satoshi)
Maintenance Information: 2022.10.7 Maintained (Terminal rust removal, acid cleaning, insulation bushing & mounting screw replacement. ATT replacement A frequency characteristic measurement check (~ approx. 42 kHz) was performed, and the original capacitor was continuously used for good results. Input/output waveform and balance check, sound output check.)
Accessories: no accessories
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg
The price has been reduced! 2020/11/9 sales price 70,000 yen maintenance completed. This is a 2-way network. Since bass can be pushed out well, and high frequency adjustment ranges can be obtained with 2 types of HF/MF attenuators, it is a model that is easy to match the desired sound quality. There are small scratches on the exterior due to the feeling of use. Serial 05234 07210 (Makoto Kono)
Maintenance information: 2020.11.9 maintained (common wiring reinforcement terminal solder removal, rust removal treatment, cleaning, ATT (x4) contact disassembly cleaning, contact grease application, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound check)
Accessories: none
Main specifications: W114 x H190 x D228 mm 1.8 kg Crossover frequency 1.2 kHz Impedance 8 ohms Level control is continuously variable up to -8 dB in the middle range is 2 kHz and the high range is continuously variable up to -6 dB at 10 kHz
Disposal prices have been reduced! Member discounts do not apply. 2023/4/2 sales price 10,000 yen*Currently sold. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use such as exterior, fading, abrasions, etc. (Kanai Hidetsugu)
Maintenance information: 2023.4.2 sound output confirmed
Accessories: none
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced. Member discounts do not apply. 2022/12/29 sales price 10,000 yen. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information:2022.12.28 operation confirmed
Accessories: instruction manual (copy)
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced! Member discounts do not apply. 2023/4/2 sales price 10,000 yen*Currently sold. The safety wire is broken. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, such as fading, abrasions, etc. (Kanai Hidetsugu)
Maintenance information:2023.4.2 sound output confirmed
Accessories: none
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced! Member discounts do not apply. 2023/4/2 sales price 10,000 yen*Currently sold. The safety wire is broken. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. On the exterior, there is a feeling of use, such as cracks, fading, abrasions, etc. on the main body (Kanai Hidetsugu)
Maintenance information: 2023.4.2 sound output confirmed
Accessories: none
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced. Member discounts do not apply. 2022/12/29 sales price 10,000 yen. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information:2022.12.28 operation confirmed
Accessories: instruction manual (copy)
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Disposal prices have been reduced. Member discounts do not apply. 2022/12/30 sales price 10,000 yen. In-ceiling subwoofer Equipped with a single 5.25-inch woofer, it provides deep bass up to 40Hz without distortion. There is a feeling of use on the exterior, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information:2022.12.28 operation confirmed
Accessories: instruction manual (copy)
Main specifications: 50 Hz to 230 kHz 96 dB 6 ohm φ391 mm depth 205 mm 6.4 kg
Variable Resistor Attenuator Bridge T Type 21 Steps Maximum Attenuation 50 dB Impedance 600 Ohms W45 x 64 mm 140 g with Volume Knob (Kojima Yosuke)
Accessories: volume knob (attached to the main unit)
Maintained! A network with a crossover frequency of 7 kHz. Ideal for MID/HIGH 3-WAY systems using the 2440. On the exterior, there is a feeling of use, such as paint peeling off and scratches scattered around. Serial 17041 17049 (Hiroki Aso)
Maintenance information: 2023.3.31 Maintained (terminal rust removal, acid wash, insulating bushing & mounting screw replacement, ATT brand new replacement, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound output check)
Accessories: none
Main specifications: crossover frequency 7 kHz allowable input (continuous program) 50 W impedance bass range: 12 to 16 ohms treble range: 12 to 16 ohms treble attenuation/variable volume mounting hole W140 x 108 mm 0.7 kg