The disposal price has been reduced. Member discounts are not applicable. 2024/6/2 sales price 1,600,000 yen ※This is a 50 Hz specification. Maintained! A new Studio Technik Dusch suspension on a glass turntable! Fonoico is also a nice setting at 155th in the Franz era. The sharpness, precision of contouring, and a very thick sound are just words. A world-class player who still grabs the hearts of many analog fans and never lets go. Enjoy sounds that can only be experienced with EMT. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.6.2 Maintained (930ST: motor detached/lubricated, adjusted. Replace deteriorated forward phase capacitors with new ones. Speed adjustment brake felt replacement. Main bearing housing detachment, gasket replacement, bearing ball damage replacement, etc., sealant attachment assembly. Replace the motor bush with a new one that has deteriorated. Replace the deteriorated turntable anti-noise rubber belt with a new one. Replace the idler with a new one that has deteriorated. 155ST: Balance adjustment trimmer resistor defective replacement. NF gain adjustment trimmer resistor noise exchange. Foundation solder deterioration correction. audio measurements. SW/VR cleaning, coat processing. Left and right output adjustment. (Running test OK)
Accessories: power cord, manual (copy), oil, connection cable (1 pair each of XLR and RCA)
Main specifications: idler drive system aluminum die-cast turntable rotation speed 33 1/3, 45, 78 rpm W490 x H234 x D410 mm [tone arm EMT929] dynamic balance type needle pressure range 0 to 5 g [equalizer amplifier 155 st] frequency characteristics 40 Hz to 20,000 Hz input impedance 140 to 200 ohms output impedance 200 to 600 ohms [cartridge TSD-15 ] MC type output voltage 0.15 mV, proper needle pressure 2.5 g, impedance 24 ohms
Maintained! A 4-way floor speaker made to order for the previous owner who was involved in Coral. It has an all-Alnico unit configuration, and the mysterious carbon-like diaphragm used in the driver, the 38cm carbon cone woofer, and giant magnet are unique things not seen in other corals. It has a strong and powerful sound typical of the company (Murakoshi Yoichi)
Maintenance information: 2024.6.6 maintenance (exterior repair/polishing/painting, rear baffle repair/painting. Driver maintenance: magnetic circuit gap cleaning center adjustment, sound absorbing material replacement. Network maintenance: frequency characteristic check, ATT cleaning, terminal installation, new wiring between units, rear terminal board mounting processing)
Accessories: none
Main specifications: 3 way 3 speakers 8 ohm crossover 300 Hz/4 kHz/13 kHz W620 x H1050 x D560 mm (main unit)
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/23 sales price 1,380,000 yen*Woofer saran net is out of stock. Limited edition of 500 units commemorating the 40th anniversary of B&W's founding. Not only are diamond tweeters that reproduce extremely clear, natural high frequencies, but their ability to reproduce low frequencies with a sense of volume is also attractive. The low range is well balanced with the mid to high range, and the localization is clear, and it is expressed with a rich sense of color, especially in classical music. As for the exterior, there is a feeling of use such as a line scratch or dullness on the back. Serial 0002291 0002292 (Asaine Tomoho)
Maintenance information: 2022.12.14 manufacturer maintained (tweeter replacement operation test)
Accessories: spike foot jumper sponge hex wrench
Main specifications: 2-way bass reflex playback frequency band 32 Hz to 33 kHz 8 ohms crossover frequency 3.8 kHz W230 x H930 x D375 mm 25 kg
The price has been drastically reduced! 2024/5/27 sales price 398,000 yen A popular model equipped with a diamond tweeter that rewrote the history of the 800 series. The color is rose. The excellent stretch that penetrates the high range without habit and the sense of volume in the mid to low range, which has a strong presence, are appealing not found in the current D3. The exterior has dullness, small scratches, and stickiness on the bass reflex. Serial 0012701 0012702 (Asaine Tomoho)
Maintenance information: 2024.5.27 sound output confirmed
Accessories: saran net jumper cable
Main specifications: 2 way 2 speakers bass reflex diamond dome tweeter 8 ohm crossover 4 kHz frequency characteristics 42 to 33 kHz W238 x H418 x D351 mm 12 kg
Both the interior and exterior have been fully restored and refreshed! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. It is beautiful due to exterior repairs (Sasaki Shota)
Maintenance information: 2024.5.10 Maintained (exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting. Saran net replacement/frame repair/reinforcement. Unit maintenance: low range/edge exchange, magnetic circuit gap cleaning/center adjustment, high pass/magnetic circuit rust removal/gap cleaning/center adjustment. Network maintenance: frequency characteristic check, ATT cleaning, faston terminal replacement, terminal cleaning)
Accessories: none
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
A masterpiece transistor type power amplifier from McKinn's heyday. The powerful, rich, and thick tone is a popular gem among jazz fans of yesteryear. The sound combined with speakers such as the 4343 is exceptional. The exterior is dull and scratched from use over time. Serial AX6653 (Tomonori Asaine)
Maintenance information: 2024.5.25 maintained (each SW VOL cleaning, lamp replacement, relay contact polishing power meter SW crack → internal reinforcement driver board capacitor replacement, power stage transistor check resistor replacement, additional meter board resistor installation capacitor replacement)
Accessories: copy of instruction manual
Main specifications: 200W+200W (1/2/4/8 ohms), equipped with an attenuator on the front, input sensitivity 0.75/2.5V, W411 x H181 x D368 mm, 38.6 kg
Full internal and external maintenance completed in 2022! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has some impact scratches and board repair marks on one side of the hakama part. Serial 003354/003047 (Fujisawa Yukishi)
Maintenance information: 2022.9.23 Maintained (terminal screws, rust removal, acid washing, cleaning. Internal connection terminal (faston) replaced with a new one. ATT (SW type) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. Check the input/output waveform and balance, and check the sound output. Unit maintenance (high range side: magnetic circuit gap cleaning/center adjustment) exterior repair/polishing/oil finish. Front and rear baffles/hakama repair/painting Saran net replacement)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Internally and externally maintained! This is the second generation of Tannoy's famous machine ARDEN. The warm and soft tone is attractive. It plays all kinds of music lusciously and gently. In particular, it works great with vacuum tube amplifiers, and the sense of orchestra scale and smooth playback of stringed instruments are satisfying enough to listen to. The exterior has been beautifully finished due to exterior maintenance. Serial 011093 016017 (Tomonori Asaine)
Maintenance information: 2024.4.18 Maintained (exterior repair/polishing/oil finish front and rear baffle/hakama repair/paint saran frame reinforcement painting/net replacement, batch polishing unit maintenance (high frequency magnetic circuit/in-gap cleaning/center adjustment diaphragm gap indirect attachment) ATT cleaning unit detachable)
Accessories: saran net
Main specifications: 2 way, 1 speaker, bass reflex system, floor type specification unit 3828, crossover frequency, 1 kHz, output sound pressure level, 91.5 dB, 8 ohms, dimensions W660 x H990 x D370 mm, weight 43 kg/book
Accuphase pre-main amplifier. The power amplifier section has a parallel push-pull configuration with a high power transistor, and the strong power supply unit and low impedance of the output circuit achieve high quality power of 120 W/ch (4 ohms) and a damping factor of 400. It is a model that pursues the performance and sound quality of separate amplifiers to the extreme, and has potential that exceeds its class. The exterior has a feeling of use such as dullness. Serial B7Y220 (Tomoho Asaine)
Maintenance information: 2024.6.7 operation confirmed
Accessories: remote control instruction manual power cable
Main specifications: output 120W+120W (4Ω) 90W+90W (8Ω) damping factor 400 W465 × H151 × D420 mm 20 kg
The price has been reduced! 2023/12/1 sales price 298,000 yen Interior and exterior refreshment maintenance has been completed and brushed up! A consumer model of the 2S-305, a timeless monitor speaker masterpiece that Japan is proud of. The thick and clear midrange and detailed high frequencies, which cannot be felt with the look, vividly reproduce vocals. The sound that accurately expresses the characteristics of an amplifier that is set regardless of whether it is a vacuum tube or transistor makes me feel the goodness of the device I have on hand that I haven't been able to see until now. The exterior is in perfect condition due to maintenance. Serial 351364 4851370 (Yamato Yuki)
Maintenance information: 2023.12.1 Maintained (exterior polishing, oil finish, exterior repair, front and rear baffle painting to create missing parts, saran net replacement, velcro replacement. Woofer maintenance center adjustment, edge damping agent application, disconnection solder treatment, center cap dent correction. Tweeter maintenance center cap internal cleaning and replacement, center adjustment, corn paper edge crack repair, edge damping agent application, unit detachment. Network maintenance frequency characteristics check, ATT contact cleaning, terminal cleaning sound operation confirmed)
Accessories: saran net
Main specifications: 2 way bass reflex system input impedance 8 ohms output sound thickness level 96 dB crossover frequency 1500 Hz W650 × H880 × D445 mm weight 50 kg
Full maintenance was carried out to replace all deteriorated parts such as capacitors and vacuum tubes! 38 FD, the most popular of the 38 series, is now in stock! The warm tone has plenty of warmth in the bass and mids, and you can enjoy the true essence of lackstone, where you can enjoy the afterglow of the tone. The exterior has a beautiful finish due to exterior maintenance, but rust etc. on the back remain. Serial 101 20007 (Tomoho Asaine)
Maintenance information: 2024.6.6 maintained (parts replacement, input/output waveform check, load test (1kHz sine wave, 8Ω load: 30W+30W, OK), sound output test) 2020.4.2 maintained (vacuum tube (50CA10), electrolytic capacitor, block electrolytic capacitor, coupling capacitor, vacuum tube socket, headphone jack, micro switch, rectifier diode, semi-fixed resistor, fuse replacement. Complete disassembly of SW/VOL contacts, polish, and apply grease to prevent oxidation and sulfidation. Circuit readjustment, input/output waveform confirmation, load test (1kHz sine wave, 8Ω load: 30W+30W), distortion adjustment (maximum output: 0.2%), sound output test)
Accessories: manual copy power cord
Main specifications: 30W+30W (4, 8, 16 ohms) line input 4 systems phono 2 systems (mm) W476 x H190 x D335 mm 18 kg
This is PLATANUS MC type phono cartridge. The connection from deep bass to high frequencies is good, and the playback ability is delicate and has a sense of density. You can honestly feel the vivid, dynamic sounds, and even the performer's emotions, and the records you've listened to over and over again until now will play richer and more beautiful music. Magnetic circuits are precision machined and integrated from large chunks of pure iron to enhance rigidity so that vibration energy from the needle tip to the power generation coil is not damaged. The printing has disappeared, and there are small scratches on the body, but the needle tip is good (Sasaki Shota)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, manual
Main specifications: Playback frequency 10 to 50,000 Hz impedance 2.5 ohms dead weight 16 g
The disposal price has been reduced. Member discounts are not applicable. 2024/5/26 sales price 348,000 yen The current ELAC speakers have arrived! It firmly follows the merits of ELAC up until now, and shines with a higher degree of perfection than ever before. With an expanse that doesn't make you feel the presence of the speaker, and the sound is delicate and bright, it is a practical speaker regardless of genre. There is a small dent in the lower woofer on one side. Serial 31800E000053/31800E000056 (Takasaki Atsushi)
Maintenance information: 2024.5.25 sound output confirmed
Accessories: instruction manual, jumper, spike holder, original box (cushioning material partially broken)
Main specifications: 2.5-way bass reflex type crossover frequency 450/2400 Hz frequency characteristics 30 to 50,000 Hz efficiency 88 dB recommended amplifier power 40 to 300 W rated input 130 W impedance 4 ohms W229 ✕ H1,000 x D266 mm 19.1 kg
Famous machines from yesteryear have been revived due to the creation of a new Saran Net and internal and external refreshment maintenance! Middle monitor walnut specification. The punchy bass and sharp, smooth mid-range are all very attractive models. In contrast to modern JBL speakers, listening to jazz with a thick mid to low range sound is excellent. Serial 72329/72332 (Murakoshi Yoichi)
Maintenance information: 2024.6.6 maintenance (exterior repair/polishing/oil finish
Front and rear baffle repair/painting, new saran net created. Unit maintenance: woofer cone paper painting/center cap dent repair on one side, mid cone paper coating/center cap dent repair on one side, TW cone paper/frame coating. Network maintenance: frequency characteristic check, ATT cleaning, terminal cleaning)
Accessories: saran net
Main specifications: Way3 speaker front bass reflex type sound pressure level 91 dB impedance 8 ohm crossover frequency 1.5 kHz/6 kHz playback frequency band 45 to 15,000 Hz W362 x H597 x D298 mm 20 kg/book
This is a standard JBL monitor that has undergone internal and external maintenance and has been refreshed. The darker and thicker tone compared to the current model still doesn't even seem to be declining in popularity. The thick, exhilarating sound goes well with jazz and rock, and the punchy sound becomes a habit. The exterior is in a beautiful state due to maintenance. Serial 32648 32951 (Yamato Yuki)
Maintenance information: 2024.6.7 operation confirmed
2021.10.15 Maintained (exterior cleaning/repair saran frame painting/net replacement cone paper touchup/tweeter grill dent correction ATT cleaning unit detachable)
2012.1.27 Maintained (ATT replacement, capacitor replacement, input/output waveform and balance check, sound output check, frequency characteristic measurement, front baffle repair (touch-up painting), exterior cleaning, plate attachment (not completely flat because there were already quite a few wrinkles)
Sound output test)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system frequency characteristics 45 Hz to 20 kHz sound pressure level 93 dB impedance 8 ohms allowable input 100 W dimensions W362 x H597 x D298 mm weight 20 kg/1
Full maintenance, such as internal and external maintenance, was carried out, and the finish was beautiful! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. Serial 55553L, 55553R (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (exterior repair/repaint) 2017.4.25 Maintained (exterior polishing/all coated woofer cone paper/unit frame paint chip putty repair grill dent correction/paint tweeter distortion and maintenance (edge deformation repair, magnetic circuit slit maintenance complete) unit detachment terminal replacement (banana plug compatible product) ATT cleaning capacitor replacement*Some capacitors before replacement Since it is difficult to remove, remove the wiring to check the remaining input/output waveform and balance, sound output check, frequency characteristic measurement check (~ 42 kHz)
Accessories: No accessories
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
This is a standard JBL monitor that has undergone internal and external maintenance and has been refreshed. The darker and thicker tone compared to the current model still doesn't even seem to be declining in popularity. The thick, exhilarating sound goes well with jazz and rock, and the punchy sound is captivating. The exterior has been beautifully finished due to maintenance. Serial 32547 32298 (Murakoshi Yoichi)
Maintenance information: 2024.5.16 maintenance (exterior repair/cleaning, saran net cleaning, repasting, ATT cleaning)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system frequency characteristics 45 Hz to 20 kHz sound pressure level 93 dB impedance 8 ohms allowable input 100 W dimensions W362 x H597 x D298 mm weight 20 kg/1
Internally and externally maintained! It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. The exterior has been finely polished to a beautiful finish. The mid-high range quality is high, and the sound of the piano sounds vividly. It is a powerful machine that can handle all genres with a sense of power even in the low frequencies. There is a very slight dent in the tweeter grill, and there are repair marks on the side (Murakoshi Yoichi)
Maintenance information: 2024.3.4 maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network frequency characteristic check, ATT cleaning, terminal replacement)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 39 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 6 ohms output sound pressure level 90 dB dimensions W427 x H695 x D335 mm weight 31 kg/bottle
The price has been reduced! 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg
A model that inherits the lineage of 4312. The sense of speed and range has been improved with a completely renewed unit, and it has been transformed into a high-fidelity speaker that can play all kinds of sources with a clean sound with good damping. There is a light thread on the top of the exterior. Serial 13466 13432 (Murakoshi Yoichi)
Maintenance information: 2024.6.6 sound output confirmed
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex impedance 6 ohms playback frequency band 45 Hz to 35 kHz output sound pressure level 93 dB size W362 x H597 x D299 mm weight 17 kg
Comes with original box This model was developed based on the 2.0S design concept of the company's higher-level model. The sound has good visibility across the entire band, has a solid sense of density, and has an excellent sense of air. Both stylus and cantilever are good (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, instruction manual
Main specifications: MC type 0.4 mV impedance 4 ohms needle pressure 1.9 to 2.2 g dead weight 12 g
The price has been reduced! 2024/6/3 sales price 148,000 yen Maintained! A driver unit suitable for sound reproduction for large halls and theaters, modeled after the standard 2-inch 375. High frequency characteristics have been enhanced while retaining a vintage feel. The cymbals play a sound that makes you think of jazz. The exterior has rust, paint peeling, etc. Serial 32769 32799 (Tomonori Asaine)
Maintenance information: 2024.6.3 maintained (diaphragm repair and installation adjustment pad dampener replacement, 18 mounting screws, replacement, distribution terminal, contact part cleaning, terminal cleaning, 8 insulating bushings, replacement, diaphragm cleaning)
Accessories: none
Main specifications: frequency characteristics, 500 to 18 kHz, crossover, 500 Hz, 16 ohms, diameter: 175 mm, height: 145 mm, approx. 11.8 kg/bottle
Woofer edge softening treatment! One of DIATONE's most popular speakers. The sharp high resolution line started with this speaker. It is a speaker representing DIATONE, which is delicate and has high transparency, and by successfully combining amplifiers, it is a very high quality speaker even now. The exterior has chipped veneer, stains, and scratches. Serial 15112, 15119 (Fujisawa Yukishi)
Maintenance Information: 2024.6.7 Maintained (woofer edge softening treatment)
Accessories: saran net
Main specifications: 3 way, 3 speakers, sealed bookshelf type, 6 ohms, playback frequency band, 28 Hz to 40,000 Hz, output sound pressure level, 90 dB, crossover frequency, 500 Hz/4.5 kHz, rated input 60 W, maximum input, 180 W, W410 x H710 x D362 mm, 38 kg
The price has been reduced! 2024/6/2 sales price 118,000 yen ROYAL AUDIO TSB-9 with dedicated stand! A popular Pioneer ribbon tweeter. A golden combination of beryllium diaphragms and alnico magnets. In addition to the ultra-high frequency sound quality correction, the expansion of spatial expression, and the wide sound field can be clearly experienced with classical sources. The exterior is dull, and there are scratches on the front mesh and pedestal (Takahashi Nobuyuki)
Maintenance information: 2024.6.2 operation confirmed
Accessories: dedicated stand
Main specifications: input impedance 8 ohms, playback frequency band, 5,000 Hz to 120,000 Hz, maximum input, 100 W, output sound pressure level, 97.5 dB, crossover frequency of 5,000 Hz or more, W134 x H89 x D179 mm, 2.6 kg
The disposal price has been reduced! Member prices are not applicable. 2024/6/2 sales price 128,000 yen Woofer edge softening treatment! Comes with a genuine stand DK-1000ZX (list price 50,000 yen). Standard diamond tone model. The characteristics of the Boron scoker, which is strong and has a good sound, shine through. The tight low range with supple stretch is a sound unique to Diatone. You can enjoy excellent sound regardless of genre. The exterior has small scratches and dullness. ※Saran net is out of stock. Serial 14308/14315 (Fujisawa Yukishi)
Maintenance Information: 2024.6.2 woofer edge softened
Accessories: Genuine stand DK-1000ZX ※Saran net missing
Main specifications: [DS-1000ZX] 3 way 3 speaker sealed type 6.3 ohm output sound pressure level 90 dB W360 × H690 × D341 mm 29 kg [DK-1000ZX] W360 × H195 × D300 mm 6.2 kg
The disposal price has been reduced (member prices are not applicable). 2023/11/26 Sales price 128,000 yen Maintained in 2022/6! An eye-catching power amplifier with its black and large power meter typical of Sansui. It entertains me with its power, which can be felt from its appearance, and its supple, stretchy sound quality. The exterior has dullness, scratches, rust, etc. over time (Oikawa Tetsuji)
Maintenance information: 2022.6.23 Maintained (both channel volumes replaced. SP relay bad contact replacement. Replace protectors, deteriorated transistors, resistors, and diodes in meter boards. Replace deteriorated transistors and resistors in the power supply board. Replace deteriorated transistors and capacitors in the drive board. OUTPUT selector switch cleaning. (General adjustment)
Accessories: none
Main specifications: left and right independent 2 power supply diamond differential circuit effective output 110W+110W (8Ω) load impedance 4 to 16 ohms W482 x H187 x D450 mm 20.3 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/12/13 Sales price 138,000 yen Maintenance completed! Newcomb tube mono prime. An output of about 12W is output using a 6V6 output tube. It has an adjustment function for a total of 36 fine phono curves, 6 low frequencies and 6 high frequencies. The stylish look reminiscent of Old Marantz, such as the hood on the back, is irresistible. Since the input terminals are on the bottom, it is necessary to devise how to insert the RCA cable. The standard LEVEL position is M. Adjust the volume with LOUDNESS. SELECTOR's RUMBLE FILTER is valid only for PHONO. ※The hood is fitted very tightly, so it cannot be removed normally. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Murakoshi Yoichi)
Maintenance information: 2023.12.12 maintenance completed (earth terminal added to bottom, vacuum tube 6AV6 replacement, 100 μF electrolytic capacitor and lug terminal added to 80/10 μF block capacitor, base leg replacement/HUM ADJ readjusted, vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 11 to 15 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Key Specifications: 6V6P.P. Rated output 12 W LINE 3 system, PHONO (MM) 1 speaker compatible impedance 8, 16 ohms, W322 x H112 x D240 mm, 6.8 kg
The price has been reduced. 2024/5/25 sales price 99,800 yen with 2447 exclusive horn! A coherent wave structure is used for the phase plug. It is designed so that the phase plug can be connected directly to the horn throat. A titanium diaphragm is used. You can see the exterior, dullness, dirt, abrasions, etc. and a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: stand
Main specifications: Throat diameter 3.8 cm 16 ohms Frequency characteristics: 500 Hz to 20 kHz
The price has been reduced! 2024/5/25 sales price 99,800 yen Maintained! Professional A version (8 ohm specification) of the LE15. This woofer has good response and allows you to enjoy a dry, tense sound. There is only one unit developed for monitors, and it is a unit that can handle large inputs. (YONEJIMA Satoshi)
Maintenance information: 2024.5.25 Maintained (edge replacement, operation check)
Accessories: No accessories
Main specifications: 38cm cone woofer Alnico 8Ω (measured DC value 7.0Ω/6.9Ω) 150W crossover 800Hz baffle opening diameter 355mm screw pitch (diagonal) 370 mm
The disposal price has been reduced. Member prices are not applicable. 2024/5/9 sales price 128,000 yen One side tweeter has been replaced! The successor model to the super popular “IKON Series.” It is equipped with a unit that uses wood fiber cone paper. The mid and low frequencies are rich, and the high frequencies sound smooth. You can feel the depth of the sound clearly (Daiki Goto)
Maintenance information: 2024.5.9 operation confirmed
Accessories: original box, jumper plate
Main specifications: 3 way 4 speakers, frequency characteristics, 39 Hz to 30 kHz, crossover 700 Hz, 2.6 kHz, 14 kHz, efficiency 89 dB impedance 6 ohms size W188 x D352 x H1028 mm weight 17.8 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/5/11 sales price 148,000 yen The BBC monitor speaker is equipped with an in-house manufactured unit based on the LS3/5A, and the phase characteristics and frequency characteristics of the mid to low range, and the responsiveness of music signals have been greatly improved. You can listen to traditional English sounds with a sense of calm. The exterior has a feeling of use such as dullness and small scratches. Serial 206B08481 206B08482 (Tomonori Asaine)
Maintenance information: 2024.5.11 operation confirmed
Accessories: saran net
Main specifications: 2 way 2 speakers sealed crossover 5 kHz impedance 8 ohms frequency characteristics 75 Hz to 20 kHz output sound pressure level 84 dB input terminal 4 mm terminal bywire compatible W165 ✕ H305 ✕ D 190 mm weight 4.6 kg
Maintained! A network using excellent parts such as high-voltage nonpolar capacitors and coils using low-loss Orient Cores. The cross is easy to use at 500 Hz, and it is a very easy to use network for those who are assembled with drivers such as 375 (Asaine Tomoho)
Maintenance information: 2024.5.16 Maintained (12 terminal terminal mounting screws, 24 insulation bushings, terminal part cleaning, main unit internal check, attenuator VR replacement, crossover check)
Accessories: none
Main specifications: 2 way network, 500 Hz, 8 ohms
Comes with original box It is an MC cartridge that uses diamond star rice chips and boron cantilevers, which are also used in higher-level models, and is characterized by outstanding high-pitched fineness and clear sound quality even in the same price range. Both the cantilever and stylus are good (Oikawa Tetsuji)
Maintenance information: 2024.6.3 operation confirmed
Accessories: original box, instruction manual
Main specifications: moving coil type, 4 ohm, needle pressure, 1.7 to 2.0 g, output voltage 0.3 mV or more, playback frequency 10 Hz to 30 kHz, solid boron, cantilever, machined aluminum, body, diamond stylus tip, 10.5 g
DALI's popular tall boy model. The high quality real wood finish exudes a sense of luxury. It features a mild, high-grade tone with a high texture, and demonstrates its strengths in acoustic sounds and female vocals. Small scratches and threads are scattered on the exterior, lower front, top, etc., and there is a feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.6.7 sound output confirmed
Accessories: instruction manual, saran net, spikes, hex wrench
Main specifications: 3 way 3 speakers, frequency characteristics, 43 Hz to 25 kHz, crossover, 3.4 kHz, sound pressure level, 90 dB, impedance, 4 ohms, W170 x H845 x D220 mm, 11.7 kg
The price has been drastically reduced. 2024/2/12 sales price 89,800 yen ※It has been replaced with a non-genuine edge. You can enjoy voluminous bass with highly efficient and heavy cone paper. It is also durable with a gathered edge, and is also recommended for backload and front load enclosures. There are viscoid sagging marks (Oikawa Tetsuji)
Maintenance information: 2024.2.12 Operation confirmed
Accessories: none
Main specifications: rated input 150 W frequency characteristics 30 Hz to 2 kHz 16 ohms efficiency 96 dB crossover frequency 800 Hz recommended enclosure volume 170 to 225 liters depth 146 mm 7.5 kg
Maintenance has been completed, such as edge softening treatment and exterior repairs. The successor to the DS-505 with a DUD boron dome in the high range. It is a model set to be the standard for the CD era, and the sound connection between each unit is smooth, and the sense of stability in the mid to low range is attractive. You can see a feeling of use, such as appearance, dullness, corrosion, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.6.4 maintenance (edge softening treatment, exterior repair/cleaning)
Accessories: saran net
Main specifications: 3-way 3-speaker bass reflex system 6 ohms playback frequency band 30 Hz to 40,000 Hz output sound pressure level 90 dB W390 x H720 x D377 mm 33 kg
The price has been reduced. 2024/5/24 sales price 79,800 yen This is a standard professional 1-inch screwdriver model. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance even when combined with various woofers and tweeters. There is a feeling of use due to appearance, dullness, small scratches, abrasions, etc. (Takasaki Atsushi)
Maintenance information: 2024.5.24 sound output confirmed
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms (measured 10/12 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Maintained. The grain of the sound is clear and the smoothness of the connection has also been improved. This is a 1200 Hz crossover network ideal for the combination of a 38 cm woofer and 1 inch driver. The exterior has dullness and scratches due to use over time, serial 18254 18275 (Asaine Satoshi Law)
Maintenance Information: 2024.4.16 Maintained (Screws, Insulated Washer Parts Replacement Switch Contact Cleaning)
Accessories: none
Key Specifications: Crossover 1200 Hz 8 Ohm 3 Position Switch with Level Control
Maintained! Professional crossover 800 Hz network. It's an exhilarating sound with a good view. How about making a 2-way horn system with a 16 ohm unit? In addition to dullness and small scratches on the exterior, there is a feeling of use such as paint peeling. Serial 8091 8074 (Hiroki Aso)
Maintenance information: 2024.5.4 maintained (12 terminal terminal mounting screws, 24 rust and insulation bushings, deterioration replacement. The capacitor used for terminal cleaning is a Dayton attenuator switch contact cleaning crossover 800Hz check red terminal cap partial deterioration replacement)
Accessories: none
Main specifications: crossover frequency 800 Hz impedance 12 to 16 ohms W122 x H154 x D132 mm 1.9 kg/1 unit
2023.12.18Maintained professional cross 800Hz network. It is used in the 4320, etc., and the low frequencies are pushed out smoothly, giving the impression that the clarity of the mid-high range has improved. This network is useful for creating 2-way systems where woofers have a certain amount of area. How about making a 2-way horn system with a 16Ω unit? There are stains and rust on the main body. (TERAMOTO Hidehiko)
Maintenance information: 2023.12.18 Maintained (terminal rust removal treatment, cleaning, mounting screw replacement. SW type ATT contact cleaning. Frequency characteristics are measured and checked, and the original capacitors are continuously used for good results. (Check the input/output waveform and balance, check the sound output)
Main specifications: crossover frequency 800 Hz impedance 12 to 16 ohms W122 x H154 x D132 mm 1.9 kg/1 unit
The price has been reduced! 2024/5/25 sales price 79,800 yen Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has rust and paint peeling due to aging. ※The diaphragm is DR16R2421. (YONEJIMA Satoshi)
Maintenance information: 2024.5.25 Maintained (diaphragm installation adjustment, pad dampener, mounting screw rust replacement. Material terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning. This is a genuine diaphragm, but it comes with DR16R2421. DCR (A/7.1 ohm diaphragm scratch) DCR (b/6.3 ohm diaphragm scratch))
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg/piece
The price has been reduced! 2024/6/4 sales price 79,800 yen The Silver series is used in woofers that use the new DCF technology. The unit, which has the familiar high-speed texture, is stored in a relatively large enclosure. The low range, which has more volume than the size, and the clear mid to high range are attractive. The exterior has a feeling of use such as dullness. Cereals (Tomoho Asaine)
Maintenance information: 2024.6.3 sound output confirmed
Accessories: jumper cable (general purpose)
Main specifications: 2-way bus reflex type frequency characteristics 40 Hz to 35,000 Hz, crossover frequency 2,800 Hz, efficiency 88 dB, impedance 8 ohms, W230 x H375 x D329 mm, weight 9.3 kg/unit
The price has been reduced! 2024/5/18 sales price 79,800 yen Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. Serial 60878/74750 (Tamura Eiji)
Maintenance information: 2024.5.18 Maintained (diaphragm installation adjustment. Pad dampener, mounting screw rust replacement. Wiring terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning, internal wiring cable replacement. DCR (74750/6Ω diaphragm no scratch) DCR (60878/5.7Ω diaphragm no scratch))
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Accuphase's dedicated analog disc input board. Using the latest circuitry and selected high-quality sound materials, extremely low noise and high-accuracy RIAA deviations have been achieved. The optimal impedance can be selected from 30/100/300 ohms during MC. It is also equipped with a subsonic filter, so you can enjoy an even higher grade analog sound than the AD-30 (Kojima Yosuke)
Accessories: instruction manual, original box
Main specifications: [MM] gain 40dB, input impedance 47kΩ [MC] gain 66dB, input impedance 30/100/300Ω switching [compatible models] C-2000, C-2110, C-2120, C-245, C-265, CX-260, E-211, E-212, E-213, E-250, E-260, E-270, E-306V, E-307, E-308, E-350, E-360, E-370, E-406 ・E-407 ・E-408 ・E-450 ・E-460 ・E-470 ・E-530 ・E-550 ・E-560 ・E-600 ・E-650
The price has been drastically reduced! 2024/4/19 sales price 79,800 yen ※1 unit only. Maintained! It is originally a professional mono amplifier, but there is only 1 unit. You can feel the strong power of the sound quality even with just one unit. It seems to be useful for mono and center speakers. There are scratches and paint peeling on the exterior. Serial Q001769 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (XLR speaker cable created (3 meters)). Electrolytic capacitor replacement. ATT cleaning. Solder correction. Rubber feet added. Bias offset check. Output audio check. Input ① GND ② HOT ③ GND (unbalanced) output ① not used ② is set to plus ③ minus 8 Ω load. (Also, a pop sound is made when the power is on and off, but this is a specification)
Accessories: speaker cable, power cable
Main specifications: 8 ohms W482.6 x H88 x D320 mm weight 13 kg
It hasn't been in stock in a long time! Accuphase Premium Cartridges Using a sapphire tube cantilever, the sound is straightforward with no specific sound, almost no distortion, and a perfect sense of range. Now it's a manufacturer that pushes ahead with the cutting edge of digital audio, but it's a cartridge where you can once again feel the high level of analog audio technology (Yamato Yuki)
Maintenance information: 2024.5.31 operation confirmed
Accessories: The original box needle cover is missing
Main specifications: MC type output voltage 0.18 mV needle pressure 1.5 to 2.5 g optimal 2 g impedance 4 ohms line contact needle
The price has been reduced! 2020/11/9 sales price 70,000 yen maintenance completed. This is a 2-way network. Since bass can be pushed out well, and high frequency adjustment ranges can be obtained with 2 types of HF/MF attenuators, it is a model that is easy to match the desired sound quality. There are small scratches on the exterior due to the feeling of use. Serial 05234 07210 (Makoto Kono)
Maintenance information: 2020.11.9 maintained (common wiring reinforcement terminal solder removal, rust removal treatment, cleaning, ATT (x4) contact disassembly cleaning, contact grease application, frequency characteristic measurement check (~ approx. 42 kHz), continue using the original capacitor for good results, input/output waveform and balance confirmation sound check)
Accessories: none
Main specifications: W114 x H190 x D228 mm 1.8 kg Crossover frequency 1.2 kHz Impedance 8 ohms Level control is continuously variable up to -8 dB in the middle range is 2 kHz and the high range is continuously variable up to -6 dB at 10 kHz
The price has been reduced! 2024/5/25 sales price 69,800 yen ※The exterior is in poor condition, so it's cheap. An upgraded model of PMC's small monitor DB1. It has excellent characteristics as a near-field monitor, and is characterized by good phase characteristics and rich spatial expression. It is a high-quality model that can be further upgraded by adding an amplifier. There are line scratches and bumps on the exterior. Also, there are cracks or tears in the urethane on the back. Serial 012503/012504 (Yonejima Satoshi)
Maintenance information: 2024.5.25 sweep test good
Accessories: saran net
Main specifications: 2 way 2 speakers, frequency characteristics, 50 Hz to 25 kHz, output sound pressure level, 87 dB, impedance, 8 ohms, dimensions: H290 x W155 x D240 mm (including grille), mass: 4.5 kg
The price has been reduced! 2024/6/1 sales price 69,800 yen Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. There are some scratches on the diaphragm on one side. Serial 60878/74750 (Yonejima Satoshi)
Maintenance information: 2024.6.1 Maintained (diaphragm installation adjustment, pad dampener installation, screw rust replacement. Wiring terminal contact cleaning, terminal dirt cleaning. Insulating bushing replacement. Diaphragm dirt cleaning. DCR (29324/6Ω diaphragm undamaged) DCR (33387/5.8Ω diaphragm damaged)
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
The price has been reduced! 2024/6/2 sales price 69,800 yen This is an EV PA speaker. You can enjoy a clean sound with crisp high frequencies and responsive low frequencies. It's made of resin and is lightweight, so it's easy to carry around. It can be used for a wide range of purposes, such as reeds at home and at events. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2024.6.2 sound output confirmed
Accessories: none
Main specifications: 1 inch driver, 30 cm woofer impedance, 8 ohms, 300 W, 80 to 25,000 Hz, size W430 x H585 x D314 mm (actual measurement), 15.3 kg (actual measurement)