Maintained! With the density and suppleness of the sound typical of THORENS, you can enjoy an analog feel not found in recent players. The arm is equipped with the SME3009R, and it is a car that can be enjoyed in a wide range of ways, from light needle pressure to heavyweight cartridges such as SPUs. There are small scratches, cracks, etc. on the dust cover (Oikawa Tetsuji)
Maintenance information: 2026.5.11 Maintained (belt replacement, internal inspection, spindle lubrication, arm operation, sound check) 2021.11.19 Maintained (replacement for belt extension, servo circuit capacitor replacement, lead screw cleaning because it is heavy, replacement due to poor rubber in the subweight, arm operation/voice check, arm end lift detection cam crack repair due to cam misalignment, fixed, rotation speed adjustment)
Main specifications: [TD-320MK3] belt drive type floating cabinet size W440 x H170 x D350 mm [3009R] static balance type short type 9 inch needle pressure 0 to 5 g compatible cartridge weight 9.5 to 22 g
Maintenance has been completed, including LED changes to the dial pointer lamp, tuner tracking, and MPX re-adjustment. KENWOOD's highest-grade vari-control tuner is still highly popular! It uses a high-precision 7-frequency linear varicon, and has a vividness as if you were listening directly to the sound of a studio. Please experience the sound quality you can't enjoy with a digital synthesizer tuner. You can see a feeling of use on the exterior, dullness, stains, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.5.11 maintenance completed (high-frequency front-end varicon gear box shaft correction, backlash improvement treatment dial pointer lamp LED change, power supply change tuner part tracking, IF characteristics, MPX, etc.)
Accessories: copy of instruction manual
Main specifications: FM dedicated tuner, 7-speed varicon, W480 x H147 x D423 mm, 12.4 kg
40th anniversary limited edition Specially designed with a special headshell It is a high cost performance cartridge characterized by high quality sound, which combines a clean and extended sense of range with just the right amount of density. Both the cantilever and stylus are good (Oikawa Tetsuji)
Maintenance information: 2026.5.11 operation confirmed
Accessories: needle cover
Main specifications: MC type playback frequency range 15 to 50,000 Hz output voltage 0.5 mV needle pressure 1.6 to 2.0 g (1.8 g standard) coil impedance 17 ohms
Maintained! Stax headphones+driver set Although it is entry grade, you can enjoy the expansive sound field expression and fresh sound typical of Stax. There is a slight flaw in the head pad (Oikawa Tetsuji)
Maintenance information: 2026.5.11 Maintained (replaced due to power circuit resistance disconnection. I checked the volume and input circuit. I checked the headphone sound. Each input was checked and the terminals were cleaned)
Accessories: power cable
Main specifications: SRM-006ts: frequency characteristics DC to 80 kHz (when using SR-407 x 1 unit) harmonic distortion ratio 0.01% or less/1 kHz (when using SR-407 x 1 unit), rated input level 100 mV maximum output voltage 300 V input impedance/50 kΩ (RCA), 100 kΩ (XLR) input terminal/XLR x 1, RCA x 2 (parallel out terminal) bias voltage DC580V power supply voltage AC100V 50/60 Hz power consumption 49 W vacuum tube/6FQ7 x 1, 6CG7 x 1 W195 x H103 x D380 mm (including protrusions) weight 3.4 kg SR-407: electrostatic ear speaker, open rear type, high moisture permeability, high-grade artificial leather earpads, playback frequency 7 to 41,000 Hz, cable length 2.5 m, 340 g (main body only)
Comes with a booklet. The original digital amplifier from the Stereo magazine appendix. It is a joint project between Luxman and Stereo magazine, and has been upgraded from the previous model, such as increased output, high sound quality capacitors, and gold-plated terminals (Oikawa Tetsuji)
Maintenance information: 2026.5.11 operation confirmed
Accessories: booklet, power adapter
Main specifications: rated output 12 W+12 W (8 ohms) frequency characteristics 10 Hz to 40,000 Hz S/N ratio 90 dB speaker impedance 4 ohms to 8 ohms
This is an 8cm metal cone full range unit. It uses a black aluminum diaphragm and features clear bass and sound quality that is straightforward and easy to listen to. It is good at reproducing bass with a sense of volume in spite of its caliber. The exterior has small scratches, dullness, etc. and a feeling of use (Tomoho Asaine)
Maintenance information: 2026.5.11 operation confirmed
Accessories: original box
Main specifications: 8 cm metal cone, full range aluminum diaphragm, neodymium (anti-magnetic type), rubber edge impedance, 8 ohms, output sound pressure level, 80 dB, playback frequency band, 80 to 15,000 Hz, minimum resonance frequency, Fo to 80 Hz, baffle aperture diameter 77 mm, external dimensions 88.5 x 88.5 mm, weight approx. 240 g
*Currently sold. DALI small speakers. It features a compact, inexpensive yet solid low range, and a glossy, easy-to-hear mid to high range. It's a sound with excellent sound spread and good visibility. Serial 7124803/7124803 (Matsumoto Tsuyoshi)
Main specifications: 2 way bass reflex type 6 ohm 84.5 dB recommended amplifier output 25 to 100 W frequency characteristics 54 Hz to 26 kHz W170 x D238 x H292 mm 4.2 kg
Visaton's 10cm full range unit. Why don't you try making your own full-range system easily? The exterior is generally good (Tomonori Asae)
Maintenance information: 2026.5.11 sweep check is good
Accessories: original box
Main specifications: impedance 8 ohms, playback frequency 95 Hz to 22 kHz, output sound pressure level 86 dB
*Set of 8 The 2 pieces of felt are attached upside down. A TAOC speaker stand with a high vibration damping effect. Made from high-carbon cast iron, the speaker system improves pitch, depth, and transparency. Recommended for middle class speakers. Exterior, other emblems described above are missing, marks, dullness, abrasions, etc., and a feeling of use can be seen (Kobayashi Hitoshi)
Accessories: none
Main specifications: Uses high-carbon cast iron W100 x H140 x D170 mm, weight 5.0 kg
*Currently sold. This is an upgraded model of the popular monitor speaker, Control 1. It can be freely placed vertically, horizontally, or mounted on a wall. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.5.10 Operation confirmed
Accessories: instruction manual, original box
Main specifications: 2-way bookshelf type playback frequency 80 Hz to 20 kHz impedance 4 ohms, LF/135 mm x 1 HF/19 mm x 1 dimensions W159 x H235 x D 143 mm weight 1.8 kg
※The saran net's broken dowel is being repaired. JBL medium bookshelf speaker. Equipped with a newly developed compression driver, it uses a port-front twin port bass reflex system. It has both an extended high range and a low range with good sound separation. There is slight dullness, but there are no major scars (Oikawa Tetsuji)
Maintenance information: 2026.5.10 operation confirmed
Accessories: saran net
Main specifications: 2-way bookshelf type frequency characteristics 50 Hz to 40 kHz impedance 6 ohms crossover frequency 3.2 kHz W278 x H460 x D300 mm 12 kg
The price has been reduced! 2026/5/7 sales price 178,000 yen The flagship CD/SACD player that DENON is proud of. The thick mid to low range and the highly textured mid to high range sound were the deciding factors for the best seller. The high level of musicality stands out even when compared to modern players. There is a feeling of use on the exterior, such as dullness, small scratches, and bald paint on the remote control. Serial 1101503891 (Tomonori Asaine)
Maintenance information: 2026.5.2 operation confirmed
Accessories: instruction manual copy remote control power cord
Main Specifications: Compatible Format SACD/CD/CD-R/CD-RW Frequency Characteristics 2Hz to 50kHz (SACD) 2Hz to 20kHz (CD) SNR 117 dB (SACD) 120dB (CD) Total Harmonic Distortion Ratio 0.0005% (SACD) 0.0015% (CD) Analog Output 2.0V Digital Output Coaxial/Optical Advanced AL24 Processing Equipped High Rigidity Chassis Structure Power Consumption 30W External Dimensions W434×H150×D410mm weight 21.8 kg
Super tweeter with built-in network capable of playback up to 70kHz. You can select where to connect the high frequency range from 3 types of input. You can use it simply by placing it on top of a normal speaker and connecting it as is. The bright, clear high frequencies and carefree tone are the perfect match for JBL speakers. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2026.5.6 operation confirmed
Accessories: none
Main specifications: 25mm sintered carbon graphite dome tweeter playback frequency band FC to 70kHz crossover 12kHz/16kHz/22kHz impedance 5Ω sound pressure level 90dB W190 × H130 × D130 mm 1.3 kg
The price has been reduced! 2026/4/27 sales price 19,800 yen RCA cable 1.0 m pair handmade cable. Details such as specifications are unknown, but it is a cable with a wide range that is well-balanced from high to low frequencies. *Please connect the green side of the plug to the amplifier. (FUJISAWA KOSHI)
Maintenance information: 2026.4.27 continuity confirmed
Accessories: No accessories
The price has been reduced! 2026/5/3 sales price 13,000 yen*There is a slight smell of tobacco. Comes with original box! A convenient tweeter when you want to add a little more high frequency from the full range. Since it's cone-shaped, it's not too tight, and it's easy to use with a soft high range. (FUJISAWA KOSHI)
Maintenance information: 2026.5.3 operation confirmed
Accessories: instruction manual, original box
Main specifications: 5 cm cone tweeter unit 8 ohms 92 dB 2500 Hz to 20,000 Hz 0.15 kg
The disposal price has been reduced! (Member prices are not applicable) 2026/4/23 sales price 398,000 yen Full maintenance has been completed from the exterior to unit, network, and attenuator overhauls! LANCASTER equipped with Alnico Magnet HPD315. The unit, which is bright and sounds in a well-balanced manner, is packaged in an airtight TANNOY box where you can feel its goodness. In addition to being able to enjoy the classic color and luster, the vocals are in good harmony due to good localization, and although it is in a beautiful state due to maintenance, there are some fraying on the saran net. ※The size of the holes in the saran net is different on the left and right (Yamato Yuki)
Maintenance information: 2025.11.20 maintained (exterior repair/polishing/clear finish front and rear baffle repair/paint saran net cleaning/reapplication, fraying repair unit maintenance (low frequency side edge replacement/magnetic circuit gap cleaning/center adjustment, corn paper unnecessary material removal/reinforcement high frequency side magnetic circuit gap cleaning/center adjustment, diaphragm noise adjustment) network maintenance (frequency characteristic check, ATT Cleaning, terminal cleaning/4-pin terminal cleaning, cleaning various places) Unit detachable)
Accessories: saran net
Main specifications: 12inch coaxial 2-way (HPD315) frequency characteristics 20Hz to 20,000 Hz allowable input 85W output sound pressure level 92dB 8Ω W535 x H840 x D320 mm weight 26 kg/book
The disposal price has been reduced! (Member prices are not applicable) 2026/4/13 sales price 898,000 yen Unit and network maintenance, exterior repairs, etc. were overhauled in 2025/8! This is a genuine British original enclosure and monitor gold 15 inch. It is an individual that sounds much better, probably because of individual differences. It is a speaker representing Tannoy that brings out the appeal of all kinds of sources. In particular, once you hear the beautiful, glossy sound in string music and vocal music, it makes a sound that you won't be able to leave your ears. A repair mark remains on the center of one side of the saran net. Serial 111936/028182 (Yamato Yuki)
Maintenance information: 2025.8.28 Maintained (exterior repair/polishing/clear finish maintenance: net cleaning/repasting, fraying repair, sound-absorbing material removal. Unit maintenance: Magnetic circuit gap cleaning center adjustment for both low and high frequencies. Network maintenance: frequency characteristic check, ATT cleaning, terminal/4 pin terminal cleaning)
Accessories: none
Main specifications: 2 way 1 speaker bass reflex system floor type 15 inch coaxial 2 way (Monitor Gold 15 inch) frequency characteristics 30 Hz to 2000 Hz crossover frequency 1,000 Hz maximum input 50 W impedance 8 ohms size W597 x H1,070 x D375 mm
The price has been drastically reduced! 2026/5/7 Denon SACD player flagship model with sales price 378,000 yen. Adopts “Advanced AL32 Processing” bit expansion and data completion technology and an “HD master clock design” that minimizes jitter in digital audio signals. The texture, which has a sense of scale and feels good against the skin, is a degree of perfection unique to flagship aircraft. The USB-DAC function is also compatible with DSD up to 5.6 MHz. The exterior is dull, and there are small scratches on the front panel. Serial 4061500623 (Tomonori Asaine)
Maintenance information: 2026.5.7 sound output confirmed (long check is being performed on CD/SACD)
Accessories: original box remote control, instruction manual, power cable
Main specifications: input terminal/optical digital input x 1, coaxial digital input x 1, USB (Type B) x 1, USB (Type A) x 1 output terminal/balanced analog audio output (L/R) x 1, unbalanced analog audio output (L/R) x 1, optical digital output x 1, coaxial digital output x 1, W434 x H149 x D406 mm 25 kg
The disposal price has been reduced! (Member discounts are not applicable) 2026/4/30 sales price 398,000 yen LINN high-end speakers have arrived. While this speaker is delicate and has a high amount of information, it is a high quality speaker with a high level of texture that is easy to listen to, so you won't get tired of listening. It is an excellent product that can also be finely adjusted with wiring and spikes. There are small scratches and dullness on the exterior. Serial 1171917/1171918 (Tamura Eiji)
Maintenance information: 2026.4.30 sweep check OK
Accessories: saran net, spikes, instruction manual
Main specifications: 5-way floor type playback frequency 49 Hz to 33 kHz (passive) 40 Hz to 33 kHz (active) input impedance 8 ohms efficiency 87 dB W210 x H1,000 x D380 mm mass 32 kg/book
The disposal price has been reduced! Member prices are not applicable. 2026/5/2 sales price 698,000 yen Maintained! A mono power amplifier with a fully balanced design worthy of being called the culmination of TRIGON. The two completely independent amplifiers inside control the movement of the speaker unit's diaphragm with independent power amplifiers for an astonishing response.*Since BTL amplifiers also emit a signal on the negative side of the speaker terminal, please do not share the negative side. The exterior has dullness and small scratches. Serial 2129, 2130 (Fujisawa Yukishi)
Maintenance information: 2026.5.2 Maintained (push switch replacement (both units) created due to insulator damage. Fixed because the ribbon cable clamp came off. Loosen the screws and tighten them. Bias and offset checks. I checked the output sound. *This model has a BTL configuration. There is also an audio output on the negative side of the speaker terminal. (Please do not ground or share the negative terminal)
Accessories: power cord
Main specifications: maximum output 650 W (4 ohms), 400 W (8 ohm) input RCA x 1, XLR x 1 output XLR (line output for bi-amp) input impedance 47 kΩ playback frequency band 0.5 Hz to 250 kHz W299 x H170 x D464 mm weight 23.9 kg
The disposal price has been reduced! Member prices are not applicable. 2026/5/2 sales price 128,000 yen with remote control and SD card! Master recorder AD/DA converter for business use. This device was originally developed for master recording in studios. In addition to PCM192 kHz recording, it also supports DSD 2.8/5.6 MHz recording and playback. It can also be used as an AD/DA converter. It is also compatible with file name editing etc. using only the main unit or connecting to a USB keyboard. It also has plenty of input/output terminals, and is also multi-functional as an AD/DA converter. This is an excellent device that allows you to record and edit high-resolution sound sources with just one unit. *Depending on the standard, SD cards may not be played, but these are specifications. As for the exterior, there is a slight unevenness in the display. (TAMURA Eiji)
Maintenance information: 2026.5.2 operation confirmed
Accessories: remote control, SD card, power cord
Main specifications: Compatible media/SDHC card (4GB to 32GB) /CF card (1GB to 64GB) Type I/*Only files can be copied with CF/SD to USB memory (2GB to 64GB), recording and playback format/44.1/48/88.2/96/176.4/192 kHz (16 bits/24 bits), analog input/output/RCA/balanced XLR digital input/output/S/PDIF/CASCADE, input Frequency/SRC off 44.1/48/88.2/96/176.4/192 kHz, SRC on 32 to 216 kHz W483 × H45 × D305 mm 4.2 kg
The price has been drastically reduced. 2026/5/5 sales price 1,380,000 yen The unit has been refreshed with internal and external maintenance including edge replacement and overhaul! A system equivalent to Westminster's modifications. Improvements have been made, such as adopting internal wiring with less transmission distortion and replacing the level control part with gold-plated parts. It has an overwhelming presence, and it is a famous machine that plays high-quality playback sound from an elegant design that looks like a work of art. The exterior has also been beautifully finished due to maintenance (Oikawa Tetsuji)
Maintenance information: 2026.5.5 maintained (exterior repair/polishing/oil finish, saran net cleaning/repasting, frame repair
Unit maintenance: low band edge exchange/magnetic circuit gap cleaning/center adjustment, high frequency side magnetic circuit gap cleaning/center adjustment network maintenance: frequency characteristic check/ATT part contact cleaning, faston terminal cleaning unit detachment)
Accessories: key, instruction manual
Main specifications: compound horn type enclosure+dual concentric unit (3839W) W1030×H1300×D631mm 115kg/bottle
The price has been drastically reduced. 2026/5/6 sales price 198,000 yen Maintenance was completed in 2023/2. This speaker system uses Sansui's unique cloisonne lattice using natural cypress wood for the front panel. It has a retro exterior and sounds full of atmosphere with good localization and a sense of volume unique to the full range. You can also enjoy upgrading to your favorite system by adding 075 or LE175DLH. It has a beautiful finish due to exterior maintenance (Oikawa Tetsuji)
Maintenance information: 2026.5.4 operation confirmed
2023.2.13 Maintenance completed (enclosure polishing, oil/wax coating, baffle painting, lattice repair/polishing/painting, backside cleaning/repasting)
Accessories: none
Main specifications: unit configuration D123 W474 x H754 x D400 mm 32 kg/1 bottle
The disposal price has been reduced! Member prices are not applicable. 2026/5/3 sales price Equipped with a beautiful lute type laminated cabinet presented by Italy, the country of strings, and a driver unit designed only for this unit at the time, this speaker is elegant in both design and sound quality. It is a famous machine that entertains the music with its relaxed atmosphere and bright sound, and continues to be popular even now. There are abrasions on one side and color loss due to sunburn. Serial 1679 (Fujisawa Yukishi)
Maintenance information: 2026.5.3 operation confirmed
Accessories: spikes, strings
Main specifications: 3 way 4 speakers bass reflex type playback frequency 32 to 40 kHz 4 ohms sound pressure level 90 dB W220 x H1,050 x D410 mm 36.8 kg/unit
Famous machines are back! Thorough maintenance was carried out from the exterior to the interior, such as exchanging terminals. In addition to the sound quality, we are also concerned about the appearance, from the feel of the knobs, the texture of the wood grain, to the frame and screws. It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. It's been half a century since it went on sale, but the brillium diaphragm unit and precise cabinet, which have become rare in modern times, far from being comparable to other current speakers, stand out even more (Oikawa Tetsuji)
Maintenance information: 2026.4.27 Maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network maintenance: frequency characteristic check/ATT cleaning/terminal replacement, unit detachment)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 40 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 8 ohms output sound pressure level 90 dB dimensions W375 x H675 x D326 mm weight 31 kg/bottle
Famous machines are back! Thorough maintenance was carried out from the exterior to the interior, such as exchanging terminals. In addition to the sound quality, we are also concerned about the appearance, from the feel of the knobs, the texture of the wood grain, to the frame and screws. It is a monitor speaker that Japan is proud of, and was also used by Swedish national broadcasting and Finnish national broadcasting. It's been half a century since it went on sale, but the brillium diaphragm unit and precise cabinet, which have become rare in modern times, far from being comparable to other current speakers, stand out even more (Mizusaki Ryo)
Maintenance information: 2026.5.3 maintained (exterior repair/polishing/full coating, unit frame painting, woofer cone paper coating, network maintenance: frequency characteristic check/ATT cleaning/terminal replacement, unit detachment)
Accessories: none
Main specifications: 3 way, 3 speakers, sealed system, bookshelf type, 30 cm cone type for low range/8.8 cm dome type for medium range/3.0 cm dome type playback frequency band for high frequencies 40 Hz to 20,000 Hz crossover frequency 500 Hz/6,000 Hz impedance 8 ohms output sound pressure level 90 dB dimensions W375 x H675 x D326 mm weight 31 kg/bottle
The price has been reduced! 2026/5/7 sales price 398,000 yen ※Jumper pins are being arranged. Maintained! A genuine Harman product. Levinson's masterpiece power amplifier. The overall response of the sound is better than the previous No. 27L, and it has been brushed up to a careful sound that makes you feel more intelligent. The way it's easy to drive a large woofer makes me feel even exhilarating. It's a powerful machine that can't help but be popular even now. As for the exterior, there are small scratches and threads on the top plate and front. Serial 3175 (Yonejima Satoshi)
Maintenance information: 2026.5.7 Maintained (34 capacitors and 8 resistors replaced. There was some deterioration in the solder, and it was fixed. DC voltage/DC offset voltage/idling current/other adjustments)
Accessories: Remo pin power cable
Main specifications: 100W+100W (8Ω) 200W (4Ω) dual mono configuration toroidal power transformer dimensions W483 x H175 x D450 mm weight 32 kg
The price has been reduced. 2026/5/7 sales price 178,000 yen Maintenance such as LEVEL volume replacement and main VR disassembly and cleaning was completed in 2021/12. The second-generation premain amplifier for NEC's masterpiece A-10. Occasionally, it makes a surprising sound when it touches the strings. It drives jazz and rock briskly with thick low frequencies and clear mid-high frequencies. Another reason for its popularity is that it is easy to separate power from pre. There is a feeling of use on the exterior, such as stains and dullness on the left side of the front panel, scratches on the VOL, paint peeling, etc. Serial 04Y0959 (Takasaki Atsushi)
Maintenance information: 2021.12.25 maintenance completed (POWER AMP LEVEL volume x 2 replacement, main VR disassembly, cleaning, input/output waveform confirmation, left and right balance confirmation, load test, comprehensive operation test to confirm normal operation, input/output waveform confirmation, rated output test (1kHz sine wave, at 8Ω load: 60W+60W, OK), sound output test) 2020.9.21 maintained (power lamp converted to LED, (Transistors, capacitors, fuses, heat dissipation sheets, IC relays, resistors, semi-fixed resistors, diodes, and power supplies SW/SP terminal replacement, re-soldering after removing old solder from substrates, switch relay/VR contact cleaning, RCA terminal cleaning/plating processing, circuit adjustment, exterior cleaning, confirmation of each input/output, running test)
Accessories: copy of instruction manual
Main specifications: output 60+60W (8Ω) phono MM/MC W430 × H150 × D430 mm 23.2 kg
The price has been drastically reduced. 2026/4/18 sales price 198,000 yen 67 electrolytic capacitors, 68 transistors, refreshed and maintained with attention to details such as main VR replacement to switch disassembly and cleaning, etc. The strong, extruded sound is full of appeal that cannot be obtained with modern audio. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.4.17 maintained (67 electrolytic capacitors, 68 transistors, 4 semi-fixed resistors, 6 rear double volumes, 2 spark killers, 2 microphone terminals, DIN terminals, power supply micro switch, fuse, 2 power cushions (ept sealer), 2 meter lamps, main VR replacement. Disassemble and clean 12 rotary switches (power, meter level, BASS, TREBLE, OVER BASS, OVER TREBLE, mode, filter, function 1, function 2, monitor), output level switch, balance VR, microphone mixing VR, headphone VR, impedance select switch, and grease is applied to the contacts. Replace the 20-point caulking fixture on the DIN terminal and RCA terminal with an M3 x 10 screw nut spring washer. Headphone jack and AUX3 jack terminals were cleaned. Each board is re-soldered and flux cleaned.
Disassemble and clean 23 RCA terminals. Power supply high voltage 150V, low voltage 37V adjustment. (Check input/output waveforms, check left and right balance, and conduct comprehensive operation tests)
Accessories: instruction manual (copy)
Main Specifications: Input Phono (MM/MC compatible) Tuner/AUX/Tape Phono input switching load switching function Frequency characteristics Phono RIAA deviation within ± 0.5 dB High level 10 Hz to 100 kHz S/N ratio High level 90 dB or more Phono 70 dB or more harmonic distortion ratio 0.03% or less Tone control Bass/Treble filter Low/High equipped with 2 output lines RCA/headphone terminal Equipped power supply AC 100V power consumption 23W dimensions W400 x H149 x D315 mm weight 9 kg
The disposal price has been reduced. Member discounts are not applicable. 2026/4/9 sales price 1,280,000 yen Full maintenance from the exterior to the unit, attenuator, and network! This is an AUTOGRAPH with an HPD385 mounted in a genuine TEAC box. I am overwhelmed by the majestic sense of scale and profound and vivid sound image expressed by the low range backroad horn and the mid to low range front short horn, and it also has a good supple and beautiful tone that cannot be obtained with TANNOY in recent years. The letters have disappeared on the attenuator (Murakoshi Yoichi)
Maintenance information: 2026.2.25 maintained (exterior repair/cleaning, rear baffle repair/polishing/painting, saran net cleaning/repasting, fraying repair, unit maintenance: low frequency side edge replacement, magnetic circuit gap cleaning/center adjustment, fastener polishing, high range side: magnetic circuit gap cleaning/center adjustment, network maintenance: frequency characteristic check/ATT cleaning, terminal cleaning, 4 Pin terminal cleaning)
Accessories: saran net
Main specifications: 2-way, 1 speaker, all-horn system, corner type usage unit, 15 inch (38 cm), HPD385 impedance 8 ohms, W1070 x H1530 x D660 mm, 78 kg