The disposal price has been reduced. Member prices are not applicable. 2023/9/13 sales price 2,980,000 yen Maintained with attention to details such as drivers and wiring! The Georgian 4 is attractive for its elaborate horn configuration and beautiful furniture-like design. It is a model with a built-in crispy horn, a structure that creates a unique sound with a rich sense of scale, and the loud sound is truly an American masterpiece, but you can also feel a somewhat English-like sex appeal. *The attenuator has been maintained, but slight chipping occurs when turning due to deterioration of the original winding resistance (Oikawa Tetsuji)
Maintenance information: 2023.9.13 Maintained (828HF disassembly and maintenance: separation from magnetic circuit and diaphragm, magnetic circuit diaphragm maintenance: cleaning of the magnetic circuit, rustproof vibration system, round out, stop noise, T350 disassembly and maintenance: separation from the magnetic circuit and diaphragm, sound pressure difference adjustment: stop noise due to resonance sound generation, elimination of sound pressure drop due to rear sound leakage. Confirm that there are no modifications inside the housing. Remove rust from screws on screw-type terminals, pickle, and polish and clean the receiving side. ATT (x4) contact cleaning. A frequency characteristic measurement check (~ 42 kHz) was performed, and the original capacitor was continuously used because the results were good. (Input/output waveform and balance check, sound output check)
Accessories: none
Main specifications: 4-way 15WK, 828HF, T350, X336 (300/3500) approx. W860 x D660 x H1,350 mm approx. 90 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/2/16 sales price 448,000 yen Maintained in 2022/7! Comes with a hood! This is a famous gem that has both thickness and sex appeal while making a quick sound. There is no boomy sound, which is a drawback of vacuum tube amplifiers, and it is a vintage sound that is still popular today due to its good tone and good balance. The exterior has stains, stains, paint peeling, etc. Serial 2417 (Tomoho Asaine)
Maintenance information: 2022.7.13 Maintained (replacement of 2 vacuum tubes 6CA7 deteriorated, 2 electrolytic capacitors → block capacitors replaced with 47 μF x 2, resistance 1W domestically produced → replaced with USA-made, bottom leg deterioration replacement/vacuum tube socket and RCA jack re-caulking repair. *Other operation checks have been performed (measured at 32 to 43 W SP: 8 Ω at rated output AC 100 to 117 V)
2021.3.28 Maintained (vacuum tube socket partially loosened, re-caulking repair, other RCA jack re-caulking repairs and AC BAL. /DC BAL. /BIAS realignment implemented. Rated output AC 100 to 117 V measured at 32 to 41 W SP: 8 Ω) Maintained on 2015.1.23 (2 VT6BH6 noisy replacements · block.c40/20/20 μf deterioration exchange and external coating · R1/2W 100Ω combustion exchange · Fuse3A Slowblow ⇒ 2.5A SlowBlow replacement with original · EL.C10μF ⇒ 20 μF original replacement 2 pieces ※ other parts check ( EL.c has been added to Block.c2 by another company. Other EL.C has been replaced by another company))
Accessories: none
Main specifications: vacuum tube EL34, 6CG7 x 2, 6BH6 x 2 output 35W+35W W346 x H192 x D250 mm 21.9 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/4/10 sales price 450,000 yen The output tube has been replaced with a GE 6550! Genuine Electri A stainless steel chassis version of the 2nd generation reprinted model. It is a model that stands out for its good SNR feel and improved fine particle feel, etc., and its depth of pocket is attractive, compatible with the latest sources. The heavy, vintage look is also wonderful. The hood is missing, there are many transformer paint peeling repair marks on the exterior, and the letters on the back have disappeared. Serial E10122 (Murakoshi Yoichi)
Maintenance information: 2017.10.18 Maintained (SW/VR disassembly contacts repolished, oxidized/vulcanized grease coated. Replace all 9P socket pins Voltage check for each part, check input/output waveforms, load test (at 1kHz, 8Ω load: 75W x 2) sound output test)
Accessories: instruction manual (copy)
Main specifications: 6550 push-pull input 2 systems (XLR/RCA) rated output 75W+75W (4/8/16Ω) mono 150W (2/4/8Ω) W406 x H190 x D305 mm 30.5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/7 sales price 398,000 yen Exterior maintenance completed! Replace network capacitors with SOLEN film capacitors. The unit is DENTECH Tune HDP385, and the enclosure is made by Shinkosha. The unit is attached by removing the back plate, and the net does not come off the front. Classical music also goes well with symphonies. The exterior is generally beautifully finished due to maintenance. Serial AYT71012 AYT71012 (Tomonori Asaine)
Maintenance information: 2024.3.7 Maintained (exterior repair/cleaning)
Rear baffle paint saran net replacement unit maintenance (exterior cleaning, low range center adjustment, screw tightening, high frequency magnetic circuit slit cleaning/center adjustment) ATT cleaning/knob adjustment unit detachment)
2015.5.14 Maintained (network capacitors replaced with SOLEN. Unit edge replacement. Magnetic circuit overhaul and operation adjustment. Saran net partial cleaning net tear repair, complementary color correction)
Accessories: none
Main specifications: used unit HPD385 frequency characteristics 20Hz to 20kHz allowable input 85W 92dB 8Ω W600 x H1075 x D380 mm approx. 42 kg/bottle
The disposal price has been reduced! (Member prices are not applicable) 2024/4/13 sales price 398,000 yen For the first time in about 7 years, CM10S2 has arrived! It lets you listen to high-response sounds. In addition to simplifying the crossover with Mundorf EVO capacitors, all important internal components have been improved, such as Vandenhall internal wiring, nickel-plated terminal trays, and the driver's anti-vibration dust plug. As for the exterior, there are scratches, threads, and deterioration in part of the urethane. Serial 1508-0011895, 1508-0011896 (Fujisawa Yukishi)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, saran net, spikes, rubber feet, jumper plates
Main specifications: 3-way bass reflex type playback frequency band 28 Hz to 50 kHz output sound pressure level 90 dB nominal impedance 8 ohms W366 x H1087 x D414 mm weight 33.5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/1 sales price 298,000 yen Interior and exterior refreshment maintenance has been completed and brushed up! A consumer model of the 2S-305, a timeless monitor speaker masterpiece that Japan is proud of. The thick and clear midrange and detailed high frequencies, which cannot be felt with the look, vividly reproduce vocals. The sound that accurately expresses the characteristics of an amplifier that is set regardless of whether it is a vacuum tube or transistor makes me feel the goodness of the device I have on hand that I haven't been able to see until now. The exterior is in perfect condition due to maintenance. Serial 351364 4851370 (Yamato Yuki)
Maintenance information: 2023.12.1 Maintained (exterior polishing, oil finish, exterior repair, front and rear baffle painting to create missing parts, saran net replacement, velcro replacement. Woofer maintenance center adjustment, edge damping agent application, disconnection solder treatment, center cap dent correction. Tweeter maintenance center cap internal cleaning and replacement, center adjustment, corn paper edge crack repair, edge damping agent application, unit detachment. Network maintenance frequency characteristics check, ATT contact cleaning, terminal cleaning sound operation confirmed)
Accessories: saran net
Main specifications: 2 way bass reflex system input impedance 8 ohms output sound thickness level 96 dB crossover frequency 1500 Hz W650 × H880 × D445 mm weight 50 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/4/25 sales price 198,000 yen manufacturer maintenance completed! Tubular premain amplifier equipped with 300B. In addition to combining a vacuum tube with a modern design, it is easy to use with easy bias adjustment. Since it can also be used as a power amplifier using the PRE-IN terminal, it is also recommended for those considering separating them in the future. Serial 05050050 (Hiroki Aso)
Maintenance information: 2024.4.25 Maintained (maintenance including restoration of the contact point of the selector polishing volume ※ vacuum tubes can still be used, but they have deteriorated appropriately over time, so please understand that this is a current product)
Accessories: instruction manual copy power cable
Main specifications: maximum output 18W+18W (8Ω) vacuum tube 300B/A grade push-pull input terminal input RCA4 system
(4 rear systems, 1 tape out system) output terminals 6/8/16 ohm, 1 system each, TRIODE original 300B power consumption 220W size 440 x depth 320 x height 200 mm weight 20 kg
Maintained! Single stereo power amplifier using 2A3 output tubes. You can enjoy the aftertaste of sound and air unique to vacuum tubes. It expresses vocals and string music in a sweet and glamorous manner. This is a well-built car at an affordable price. The appearance is fine, with no noticeable scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.29 maintenance completed (power supply capacitor replacement, RCA jack replacement, cord clamp added to keep unused wire away from heat source, fixed solder defects, vacuum tube pin cleaning, bias check ham balance adjustment, output approx. 4.5 W (current load set to 8 Ω), interior and exterior cleaning)
Accessories: power cable
Main specifications: rated output 3.5W+3.5W vacuum tube 2A3 x 2 6H8C x 2 5U4G x 1 W360 x D210 x H190 mm 16 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/14 sales price 198,000 yen This model takes the configuration of the flagship 7S1. The quality of the sound has improved compared to the predecessor, and in particular, the thickness of the sound has increased from low to medium, making it a well-balanced sound. The clear and clean spatial expression and smooth, gentle mid-high sound are attractive. There is a scratch on the top plate. Serial 20011208001208 (Fujisawa Yukishi)
Maintenance information: 2024.4.14 Operation confirmed
Accessories: remote control, instruction manual, power cord, connection cord
Main specifications: original mechanical module SACDM-1 1 bit DSD SEIKO NPC SM5866AS D/A converter with external clock terminal W440 x H127 x D413 mm 16.5 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/6/24 sales price 178,000 yen Maintenance has been carried out and deteriorated capacitors etc. have been replaced! A newly created power supply is included. Genuine RF MC cartridge head amplifier The RCA terminal specification makes it easy to use, and has a separate power supply structure. The delicate, clear, and powerful sound is attractive (Daiki Goto)
Maintenance information: 2023.6.24 maintained (new power supply manufactured because the power module is defective but cannot be repaired, all deteriorated capacitors replaced, pin jack deterioration replaced, gain changeover switch replaced due to poor contact, each gain readjusted, operation inspected, (there are no current problems with the module)
Accessories: copy of instruction manual
Main specifications: Gain can be adjusted in 3 levels; input impedance can be used up to 45 ohms W175 x H60 x D210 mm 1.4 kg
The disposal price has been reduced! (Member prices are not applicable) 2024/4/22 sales price 148,000 yen Maintained! A driver unit suitable for sound reproduction for large halls and theaters, modeled after the standard 2-inch 375. High frequency characteristics have been enhanced while retaining a vintage feel. The cymbals play a sound that makes you think of jazz. The paint is peeling off. Serial 32769, 32799 (Fujisawa Yukishi)
Maintenance information: 2024.4.22 maintained (diaphragm installation adjustment, pad dampener replacement)
Accessories: No accessories
Main specifications: frequency characteristics, 500 to 18 kHz, crossover, 500 Hz, 16 ohms, diameter: 175 mm, height: 145 mm, approx. 11.8 kg/bottle
D/A converter with a dual monaural configuration equipped with 2 “ES9038PRO” units. Using 3 Talema toroidal transformers, you can feel the creator's commitment. More natural sound can be reproduced. On the exterior, there are noticeable line marks on the top plate (Tamura Eiji)
Maintenance information: 2024.4.28 Operation confirmed
Accessories: power cable
Main Specifications: Coaxial/BNC/AES/Optical: PCM44.1k to 192 K/16 to 24 bit, DOP64 I2S Input: RJ45/HDMI PCM44.1K to 768K 24/32 bit DSD64 to DSD1024 DOP64 to 256 W430 x H80 x D335 mm Weight 5.4 kg
Denon's SACD player. It is a standard model equipped with the Advance AL32 Processor, the latest version of Denon's Alpha processing technology, and has generously introduced the latest technology. You can fully enjoy the depth of the sound, and the SN has been further improved compared to the previous model. There are small scratches on the exterior. Serial 3081502128 (Jun Tamai)
Maintenance information: 2024.4.29 sound output confirmed
Accessories: Remote control* instruction manual in preparation, power cable
Main specifications: SACD compatible analog audio output/optical digital output x 1, coaxial digital output x 1 optical digital input x 1 USB (TypeB) x 1 USB (TypeA) x 1 D/A converter compatible sampling frequency 32 to 192 kHz size W434 x H138 x D335 mm weight 13.7 kg
The disposal price has been reduced. Member prices are not applicable. 2024/3/21 sales price 128,000 yen Maintained! Quad power amplifier Despite its compact body, you can enjoy a smooth, thick sound. It really goes well with speakers made in England, and makes you listen to 70s analog sound with a sense of dynamism. The exterior has a feeling of use appropriate for the model year, such as line scratches on the top plate, rubber footprints, and overall dullness (Mizusaki Ryo)
Maintenance information: 2024.3.21 maintained (internal Tn, C, R check, Tn OK, gain setting C, DC cut C, etc. → replacement, DINININPUT connector replacement, cable creation ~ operation check)
Accessories: power cord, connection cord, copy of instruction manual
Main specifications: 100W+100W frequency characteristics 20 to 20 kHz dimensions W341 x H115 x D195 mm weight 9 kg
The disposal price was lowered. Member discounts are not applicable. 2021/11/27 Selling price 148,000 yen The product around 1920 features a telescopic tone arm, needle pressure, and volume adjustment possible. 2-spring, oval straight horn The volume is not large, but the tone is delicate and coherent. The rotation is relatively stable, but there is sound cracking, so it is currently sold. The appearance has dirt scratches of age. (Takimoto Yutaka)
Maintenance information: 2021.11.27 operation confirmed
Accessories: handle
Main specifications: W440 × H380 × D520mm 17.9kg (actual measurement)
Maintained! A classic British Quad stereo power amplifier. Small in size yet full torque. The sound, which is as deep as a tube amp, exudes an appeal that won't fade. The exterior has a feeling of use over time, such as dullness and small scratches. Serial 62226 (Yonejima Satoshi)
Maintenance Information: 2024.3.25 Maintained (INPUT DIN 4P replacement, internal Tr, C, R all checks. DIN4P-RCA female cable created. Operation check, pattern solder processing)
Accessories: power cable, connection cable
Main specifications: 45W+45W W120×H159×D324mm 8.2 kg
The 3rd generation model of the S10 series. Equipped with analog waveform reproduction technology AL24 Processing. The degree of perfection of the sound is extremely high, and in addition to the heavy mid-low range, the music is pleasantly enjoyable with colorful tones unique to Denon. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 1021503089 (Hiroki Aso)
Maintenance information: 2024.4.22 Maintained (current laser pickup level is within regulations; if it breaks down in the future, pickups cannot be obtained loading belt tray opening/closing SW replacement sound test)
Accessories: instruction manual copy remote control power cable
Main specifications: 24bit/96kHz alpha processor, HDCD decoder with DA converter function (coaxial/optical switching), W430 x H130 x D330 mm, 14 kg
The disposal price has been reduced (member prices are not applicable). 2023/11/26 Sales price 128,000 yen Maintained in 2022/6! An eye-catching power amplifier with its black and large power meter typical of Sansui. It entertains me with its power, which can be felt from its appearance, and its supple, stretchy sound quality. The exterior has dullness, scratches, rust, etc. over time (Oikawa Tetsuji)
Maintenance information: 2022.6.23 Maintained (both channel volumes replaced. SP relay bad contact replacement. Replace protectors, deteriorated transistors, resistors, and diodes in meter boards. Replace deteriorated transistors and resistors in the power supply board. Replace deteriorated transistors and capacitors in the drive board. OUTPUT selector switch cleaning. (General adjustment)
Accessories: none
Main specifications: left and right independent 2 power supply diamond differential circuit effective output 110W+110W (8Ω) load impedance 4 to 16 ohms W482 x H187 x D450 mm 20.3 kg
The disposal price has been reduced. Member prices are not applicable. 2024/1/18 sales price 118,000 yen Maintained! QUAD's first transistor preamp. The deep sound image and the impression that the natural atmosphere has definitely increased, and the glossy way it rides and the sound that goes through the core make you think it's a vacuum tube amplifier. Of course, it's a combination with the 303, and the sound doesn't feel out of place even when paired with a vacuum tube power amplifier. BAL knobs are worn out (Daiki Goto)
Maintenance information: 2024.1.18 Maintained (front push button contact failure → cleaning, PHONO/LINE in-board coupling capacitor replacement. AC spark killer capacitor broken → replaced, each VOL cleaned, power cable created)
Accessories: copy of instruction manual
Main specifications: external dimensions W550 x H110 x D220 mm, weight approx. 7.4 kg (actual measurement) [33] 3 input/line systems, 1 phono system (MM) [FM3] tubular FM dedicated tuner with automatic stereo/mono switching
The disposal price has been reduced! (Member prices are not applicable) 2023/4/16 sales price 138,000 yen genuine Rin Japan product. The Sneaky DSM with built-in network player function and 2ch amplifier has arrived. It has a smart design that eliminates anything superfluous, and can be operated with an iPod or the like. Of course, it also has an excellent external input function. There are no noticeable scratches on the exterior. Serial 1324171 (Fujisawa Yukishi)
Maintenance information: 2024.4.16 Operation confirmed (Ver. 4.104.518)
Accessories: remote control, power cord, original box
Main specifications: analog input: RCA1 system digital input: coaxial, 1 optical system, 3 HDMI output, 1 HDMI system*RCA has variable output and fixed output can be changed by setting Compatible files: FLAC, WAV, Apple Lossless, AIFF, MP3, WMA, AAC, OGG Compatible Bits: 16 to 24 bits 33W ✕ 4ch (4Ω) W350 ✕ H54.5 ✕ D215mm Weight 2.3 kg
The price has been drastically reduced. 2024/3/2 sales price 99,800 yen Maintained! professional monitor amplifier It has strength unique to commercial use, and the driving power in the low range is truly remarkable. However, it also has a strong sense of temperature typical of a quad, so it is an amplifier that I would like people who are shunned when the sound is too straight for commercial use to try it once. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.3.2 maintained (internal dismantling all check, Tr, C, R check, ±B INPUT bypass C replacement, Tr, R, etc., all OK, INPUT photocoupler check, operation check)
Accessories: copy of instruction manual, power cord, dedicated SP cord (cable length 2.5 m)
Main specifications: 100W+100W (8Ω) W483 × H88 × D310 mm 12.5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/15 sales price 118,000 yen Maintained! The thin preamp from the musical Fidelity has an English style taste where you can feel the elegance, and the perfect balance of high frequencies that don't insist too much on the thick, thick mid-low range unique to this era feels good. The tape/monitor switch has been repaired and replaced and is a non-genuine product. The exterior is dull overall, with small scratches and a lot of feeling of use (Asaine Tomoho)
Maintenance information: 2023.10.26 maintained (TAPE1 monitor switch defective → non-genuine silver knob replacement. Rear terminal screw idle rotation all replacement, operation check) 2023.10.12 maintained (main VOL noise → replacement. Treble distortion noise VOL replacement (original not available, replacement with replacement, no click on the midpoint position) IC, DC leak defect replacement, capacitor deterioration replacement, operation check.
(We will not be able to respond if the dedicated parts are defective in the future)
Accessories: none
Main specifications: external power supply system with PHNON (MM MC) CR type RIAA equalizer output 2 systems W482 x H57 x D166 cm 3.0 kg
The core model for Marantz SACD players. Although it is an entry model, it has a high S/N feel typical of the company's products, and the sound quality is excellent for listening for a long time. It is an attractive player with a sense of quality in the mid to high range with a fine particle feel. The exterior has a feeling of use such as dullness and small scratches. Serial 20000540002323 (Takahashi Nobuyuki)
Maintenance Information: 2024.4.25 Operation confirmed
Accessories: remote control instruction manual power cable
Main specifications: SACD/CD player, 1 analog output system (RCA), 2 digital output systems (coaxial x 1, optical x 1), digital filter, switch to 3 modes, W440 x H123 x D419 mm, 13.5 kg
The disposal price has been reduced. Member prices are not applicable. 2023/9/23 sales price 118,000 yen This is a high sound quality studio preamp with feedback on design and development technology for professional consoles and DC power amplifiers. It has a high-grade design, such as an input level equipped with a large machined aluminum knob, monitor level volume, an R core transformer, and a luxurious power supply unit using a large capacity capacitor. There are hit scratches and line scratches overall (Daiki Goto)
Maintenance information: 2023.9.23 Operation confirmed
Accessories: power cable
Main specifications: Input SOURCE INPUT 4 stereo systems (1 of which is balanced input) DECK INPUT stereo 4 systems output MONITOR OUTPUT stereo 2 systems (1 of which is balanced output 2 hot) DECK OUTPUT stereo x 4 W483 x H181 x D44 mm 3.4 kg
The price has been drastically reduced. 2024/2/18 Marantz pre-main amplifier with sales price 89,800 yen. The preamp circuit has been revamped to enhance spatial expression ability and detail reproducibility. Similar to the PM-10 and PM-14S1, a highly accurate electronically controlled volume is used for the volume circuit. It makes it possible to reproduce bass that combines a sense of scale and instantaneous power. Serial AWY15180500756 There are scratches on the top plate on the exterior (Hiura Katsuji)
Maintenance information: 2024.2.18 Operation confirmed
Accessories: remote control power cable
Main specifications: 100W+100W (4Ω), 70W+70W (8Ω) frequency characteristics 5Hz-100kHz
W440×H128×D379mm 12.0kg
The price has been reduced! 2024/4/19 sales price 79,800 yen ※1 unit only. Maintained! It is originally a professional mono amplifier, but there is only 1 unit. You can feel the strong power of the sound quality even with just one unit. It seems to be useful for mono and center speakers. There are scratches and paint peeling on the exterior. Serial Q001769 (Fujisawa Yukishi)
Maintenance information: 2024.4.19 Maintained (XLR speaker cable created (3 meters)). Electrolytic capacitor replacement. ATT cleaning. Solder correction. Rubber feet added. Bias offset check. Output audio check. Input ① GND ② HOT ③ GND (unbalanced) output ① not used ② is set to plus ③ minus 8 Ω load. (Also, a pop sound is made when the power is on and off, but this is a specification)
Accessories: speaker cable, power cable
Main specifications: 8 ohms W482.6 x H88 x D320 mm weight 13 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/29 sales price 99,800 yen Maintenance completed! The design full of oldies is attractive, and Newcam's mono mixer premain for PA. 6L6 is used as the output tube. Channel 1 is compatible with LINE, PHONO, and MIC, and channels 2 to 4 are compatible with microphones. The volume for each channel is around 12 o'clock, and MASTER is used for volume adjustment. There is a feeling of use such as small scratches and paint deterioration appropriate to the exterior model year (Kobayashi Hitoshi)
Maintenance information: 2023.12.12 maintenance (master volume disassembly, cleaning repair, contact repair for each part such as MIC input transformer, etc., left side front lamp off, 12AX7, 150 μF electrolytic capacitor replacement. Vacuum tube socket and RCA jack caulk repair. Operation checked (measured at 41 to 61 W SP: 8 Ω with rated output AC 100 to 117 V).
Accessories: none
Main specifications: 6L6 push-pull 60W mono LINE, 1 PHONO system each, MIC4 system W440 x H190 x D350 mm 16.5 kg
This model is specialized for 3009S2 light needle pressure and has narrowed down applications. The sharpened, sharp followability is attractive. You can enjoy the sharp cuts and the large amount of information typical of an analog disc. The stoic and beautiful design, similar to a precision machine, is also excellent. Serial 182902 (Fujisawa Yukishi)
Maintenance information: 2024.3.1 continuity confirmed
Accessories: phono cable
Main specifications: static balance type needle pressure 0 to 1.5 g cartridge dead weight 4 to 9 g
The speaker cable is a conductor consisting of 350 cores in all, a 2.0m pair of end rod terminals, and is very heavy (about 2 kg per piece with only the core box part!). It has a unique presence, full of a sense of craftsmanship that cannot be found with other cables. Contrary to being rugged, the sound is detailed and smooth. As you raise the volume, you can see its true value. There are scuffs, fraying, and dirt on the sheath ※Since the core box is extremely heavy, installation requires ingenuity so that no load is applied to the cable and speaker terminals. The distance from the box to the cable terminal is approximately 15 cm. Connect the terminal side with the red seal in the middle of the sheath to the amplifier, and the terminal on the core box side to the speaker (Kojima Yosuke)
Accessories: none
Main specifications: total weight 4.8 kg
The speaker cable is a conductor consisting of 350 cores in all, a 2.0m pair of end rod terminals, and is very heavy (about 2 kg per piece with only the core box part!). It has a unique presence, full of a sense of craftsmanship that cannot be found with other cables. Contrary to being rugged, the sound is detailed and smooth. As you raise the volume, you can see its true value. There are scuffs, fraying, and dirt on the sheath ※Since the core box is extremely heavy, installation requires ingenuity so that no load is applied to the cable and speaker terminals. The distance from the box to the cable terminal is approximately 15 cm. Connect the terminal side with the red seal in the middle of the sheath to the amplifier, and the terminal on the core box side to the speaker (Kojima Yosuke)
Accessories: none
Main specifications: total weight 4.8 kg
MARK LEVINSON JC-2 power supply box produced by Rizaye. Operation has been confirmed. The main unit connection cable is not included. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.21 Operation confirmed (sound output confirmed on JC-2)
Accessories: power cable
Main specifications: W140 x H83 x D204 mm 1.1 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/4/18 sales price 79,800 yen with MA15 woofer fixing bracket! An original product. A floor-type enclosure that uses a rear loading horn system. The interior has a folding horn structure with a total length of 2 meters, making it possible to reproduce powerful bass far exceeding its size. The exterior has chipped corners, scratches, repair marks, and paint peeling. Serial 11154 (Tomoho Asaine)
Accessories: MA15 woofer grill net
Main specifications: hole diameter 365 mm, screw pitch 420 mm backroad horn compatible speakers 2205, 2225, E140 minimum playback frequency 50 Hz main material particle board+Yonematsu laminated plywood (front baffle/road horn) W603 x H12 x D603 mm approx. 54 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/12 sales price 69,800 yen Maintained! A slightly unusual Crown consumer power amplifier. It is thin and rack-mountable. A lot of straight sounds are alive and well. It is also suitable as a separate introductory machine. The exterior is dark and has small scratches (Oikawa Tetsuji)
Maintenance information: 2024.3.12 Maintained (volume volume noise was confirmed, so custom-made volume left and right were replaced, (click sound will disappear due to replacement of custom-made product) Running test with other sounds)
Accessories: none
Main specifications: 50W+50W (8Ω) W480 x H40 x D320 mm 7.5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/12/15 sales price 79,800 yen Maintained! JBL professional 2 inch screwdriver It is an item that continues to be used today in large horn systems, etc. The quality unique to titanium diaphragms makes the vocal breathing, drum hi-hat, and outstanding realism no matter which one you take. The exterior has dullness, scratches, rust, etc. due to use over time. Serial 53400 63923 (Tomonori Asaine)
Maintenance information: 2023.12.15 Maintained (diaphragm installation adjustment throat cleaning DCR 63923/8,3 ohm, no vibration damage
(DCR 53400/7.8Ω vibration has scratches and small dents)
Main specifications: throat diameter 5 cm; allowable input: 100 W; sound pressure level: 111 dB/w/m; frequency characteristics: 500 Hz to 20 kHz; crossover frequency: 500 Hz or more; 16 ohms; diameter: 235 x depth: 132 mm; 13.6 kg/1
The disposal price has been reduced! Member prices are not applicable. 2024/4/12 sales price 70,000 yen B&W 805D series speaker stand. Equipped with a spike insulator “T-PROP”. It is a speaker stand with a completely new concept developed with the theme of eliminating speaker stress as much as possible by absorbing and releasing it in a natural way without putting a load on the diamond formation structure. The exterior has scratches, paint peeling, and bumps. (FUJISAWA KOSHI)
Accessories: insulator T-PROP, screws
Main specifications: top plate W227 x D306 mm B&W 805 Diamond, D3 specially designed bottom plate W280 x D360 mm height 500 mm approx. 15 kg
The disposal price has been reduced. Member discounts are not applicable. 2024/2/6 sales price 59,800 yen ※1 shelf board is missing and has 3 tiers, and is cheap because there are many scratches. A popular large rack. It is a model that can even adjust the storage capacity and height. It also has high performance as an audio rack, and is made of full-bodied natural wood, with a sturdy structure and interior design. You can see a feeling of use, such as appearance, dullness, small scratches, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W1230 x H703 x D563 mm Weight approx. 52 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/1/18 sales price 49,800 yen Maintained! An American-made amplifier from the 1970s that can hardly be seen today. Circuits for self-preservation, such as security, correction, and protection, have been cut off, and I think that handsome atmosphere is well reflected in the sound. It has the same feeling of use as the model year (Daiki Goto)
Maintenance information: 2024.1.18 Maintained (LED installation (original not available) poor power stage transistor deterioration, defective transistor in the board → replacement. Bias adjustment, operation check.)
Accessories: none
Main specifications: size (actual measurement) W406 x H155 x D327 mm weight (actual measurement) 12.2 kg
A record player equipped with Bluetooth and USB that has sold a total of approximately 1 million units worldwide. You can listen to the sound of records with your wireless speakers or wireless headphones. Since you can move freely within the range of Bluetooth radio waves, you can easily enjoy the sound of records. Furthermore, it is equipped with a USB terminal that can convert record sound sources into digital data. The condition is generally in good condition. *The included shell cartridge is out of stock. Serial 234198228 (Yamato Yuki)
Maintenance information: 2024.4.8 operation confirmed
Accessories: copy of the instruction manual, EP adapter, USB cable, phono cable (general purpose)
Main specifications: Direct drive system 33-1/3, 45 or 78 rotations/minute communication system Bluetooth standard Ver.5.2 compliant USB function 16 bit, 44.1 kHz or 48 kHz USB 1.1 compliant Microsoft Windows 8.1 or higher, MAC OSX or higher W452 x H141.6 x D352 mm 8 kg
The disposal price has been reduced. Member discounts are not applicable. 2023/6/12 sales price 49,800 yen ※1 mono amplifier only. The display lamp visible through the lattice is a transistor mono power amplifier with an indescribable design. As for the sound quality, it is a powerful sound with a sense of overhang while making you feel thick, and the low frequencies are not sluggish, making you listen to a pleasant sound. The exterior is dull all over, scratches on the top plate, etc., and there is a feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.6.13 Maintained (output relay contact correction input volume disassembly contact correction protection circuit transistor replacement input terminal polish)
Accessories: none
Main specifications: effective output 150 W, input level adjustment, SNR 110 dB, dimensions W436 x H95 x D328 mm, weight 11.5 kg/1 unit
The price has been reduced. 2024/4/15 sales price 35,000 yen It is a high-end masterpiece that has been loved by Sennheiser for a long time. As a studio monitor, it demonstrates its power without regret. It expresses delicate sound and clear space, and provides both vocals and performances with high resolution. There is a slight feeling of use on the earpads (Kanai Hidetsugu)
Maintenance information: 2024.4.15 sound output confirmed
Accessories: original box, instruction manual, cable
Main specifications: dynamic open air, 300 ohms, 103 dB, playback frequency band 10 to 39,500 Hz, cable length: 3.0 m, mass: approx. 260 g
Speaker cable, 8.5 m pair terminal, banana - QED 40th anniversary model, cylindrical 6-core structure, has a high sound density, and the sound full of strength and dynamism is attractive. The handling is poor, but the excellent cost performance in terms of sound is truly QED! The exterior is dull and has a feeling of use (Jun Tamai)
Maintenance information: 2024.4.28 continuity confirmed
Accessories: none
Key Specifications: Comments in progress
Speaker cable 1.1 m pair terminal The company's highest-grade cable using 4 types of 8N wires with different unprocessed wire diameters. As it looks, the center of gravity is low, and it is very stable. Definitely for those who want to enjoy the majestic sound! There is a scuff stain on the sheath (Kojima Yosuke)
Accessories: none
Power cable 3.0 m A power cable that uses the company's KS-00 cable, uses an AET PSE-018V2HG as the outlet plug, and an AET PSE-320HG as the inlet plug. Compared to the predecessor, it is a monitor and high-resolution oriented model that has excellent high-frequency reproduction capability and resolution, and transmits sound images more clearly than ever before (Kojima Yosuke)
Accessories: none
The disposal price has been reduced. Member prices are not applicable. 2023/10/23 sales price 29,800 yen ※Currently sold. Comes with a special case! Portable headphone amplifier with built-in D/A converter. DSD256 (11.2 MHz/1 bit) PCM supports native playback of up to 768 kHz/32 bit. Please enjoy the sound quality unique to a thick mojo in the mid to low range. There is dullness and a feeling of use (Sasaki Shota)
Maintenance information: 2023.10.23 Operation confirmed
Accessories: original box
Main specifications: output level 35 mw/600 ohm, 720mw/8 ohm, output impedance 0.075 Ω, dynamic range, 125 dB input system, 3 optical systems, 1 coaxial x 1, microUSB x 1, 2 output systems, headphone jack x 2, charging time, approx. 5 hours continuous operation time, approx. 8 hours W82 x H60 x D22 mm 180 g
The price has been reduced! 2024/3/6 sales price 25,000 yen speaker cable 1.0 m pair banana on both ends uses the company's highest-grade cable material. Recommended for those who want to improve the tightness of the low frequencies. On the exterior, there is a part where the rubber ring on the terminal is off. ※The cable is stiff, so please be careful when routing (Tamura Eiji)
Maintenance information: 2024.3.6 continuity confirmed
Accessories: No accessories
Amplifier/Speaker Selector It can be used to switch between 3 amplifiers and 2 sets of speakers (or 3 sets of speakers and 2 amplifiers). High quality, which pays attention to the quality of domestic cables, is selling well. There is a slight feeling of use (Takasaki Atsushi)
Maintenance information: 2024.4.28 continuity confirmed
Accessories: none
Main specifications: 24K gold-plated speaker terminal compatible with both stripped wire and banana plug input 3 (L/R) /output 2 (L/R) or input 2 (L/R) /output 3 (L/R) dimensions H55 x W200 x D175 mm, weight approx. 1.4 kg
The disposal price has been reduced. Member prices are not applicable. 2023/12/10 sales price 25,000 yen*Since the output terminal has been remodeled to an XLR terminal, it is inexpensive. It is a pretty niche product that uses 2 stereo amplifiers so that it can be used like a mono amplifier. Actually, it seems to be a product intended for use with the company's 405-2. There is a lot of dullness on the exterior due to aging (Fujisawa Yukishi)
Maintenance information: 2023.6.4 sound output confirmed
Accessories: none
Main specifications: W80xH47xD140mm approx. 1.0 kg/unit
Amplifier/Speaker Selector It can be used to switch between 3 amplifiers and 2 sets of speakers (or 3 sets of speakers and 2 amplifiers). High quality, which pays attention to the quality of domestic cables, is selling well. There is a slight feeling of use (Takasaki Atsushi)
Maintenance information: 2024.4.28 continuity confirmed
Accessories: none
Main specifications: 24K gold-plated speaker terminal compatible with both stripped wire and banana plug input 3 (L/R) /output 2 (L/R) or input 2 (L/R) /output 3 (L/R) dimensions H55 x W200 x D175 mm, weight approx. 1.4 kg
The price has been reduced. 2023/6/1 sales price 25,000 yen A fully discrete genuine analog amplifier designed with an amplifier using a total of 10 pairs of carefully selected transistors without using an operational amplifier. It's lightweight, compact, and useful for portable applications. The exterior has scratches and scratches on the main body (Mizusaki Ryo)
Maintenance Information: 2023.6.1 Sound output confirmed
Accessories: AC adapter, USB cable, silicone band, carrying case, original box
Main specifications: input 3.5mm mini terminal output 3.5mm mini terminal input impedance 30kΩ output 200mW (32Ω) 100mW (50Ω) 50mW (300Ω) 15mW (600Ω) W97 x D46 x H19 mm (including volume knob) weight approx. 117 g
RCA cable, 0.5 m, pearitz coated OCC copper, has a relatively clean tone, and is a product made by Wireworld that is particular about sound quality while keeping costs down. (FUJISAWA KOSHI)
Maintenance information: 2024.4.12 continuity confirmed
Accessories: original box