*Currently sold. Yamaha superwoofer equipped with a 20 cm x 2 double woofer. Equipped with active servo technology and a 150W high-power amplifier, it plays bass that is small yet full of volume. There is dirt, dirt and dullness on the exterior, and some floating on the bottom. Serial Z117079QS (Tamura Eiji)
Maintenance information: 2024.3.3 sweep test is good
Accessories: No accessories
Main specifications: used unit 20 cm cone type x 2 rated output 150 W (5 ohms) playback frequency band 20 Hz to 160 Hz high cut filter 40 Hz to 140 Hz, continuously variable W235 x H602 x D463 mm 20 kg
The 1.8 m PSE standard MK2 power cable is not only flexible and easy to use, but the sound quality has also been brushed up with fewer habits. You can get clear, sharp sound. There is a frayed sheath (Tamura Eiji)
Maintenance information: 2024.4.24 continuity confirmed
Accessories: none
The 1.8 m PSE standard MK2 power cable is not only flexible and easy to use, but the sound quality has also been brushed up with fewer habits. You can get clear, sharp sound. There is a frayed sheath (Tamura Eiji)
Maintenance information: 2024.4.24 continuity confirmed
Accessories: none
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
※Since it is inexpensive, it will be handed over as is. Tamban 10cm full range unit. An ultra-thin PP diaphragm with reinforced ribs is used. The sound is clear and crisp. A 6-8 liter bass reflex box is recommended (Tamura Eiji)
Maintenance information: 2023.10.1 sweep check OK
Accessories: none
Main Specifications: Rubber Edge Impedance 4 Ohms Sound Pressure Level 87 dB Frequency Band 63 to 17,000 Hz Maximum Input 40 W Baffle Aperture Diameter 94 mm Weight 380 g
* Since there are difficulties with the attachment part on both sides, it is inexpensive. Line matching transformer sold primary: 600 ohms, output 10 dBm, frequency range, 50 to 10 kHz, W44 x H65 mm, 0.25 kg/piece, the head of the mounting bolt on one side is flying off, and there is distortion in the screw hole on the other side (Kojima Yosuke)
Accessories: none
Line matching transformer sold 1 piece Primary: 600 Ω - CT Secondary: 600 ohms Output 10 dBm Frequency Range 50 to 10 kHz W44 x H65 mm 0.25 kg/piece There are bumps and paint peeling in places (Yosuke Kojima)
Accessories: none
Line matching transformer sold 1 piece Primary: 600 Ω Secondary: 600 Ω Winding Ratio 1:1 Output 10 dBm Frequency Range 50 to 10 kHz W34 x H42 x D22 mm Approx. 0.1 kg (Yosuke Kojima)
Accessories: none
Wood cabinet for TD-124 of unknown manufacturer. It can be equipped with an SME long arm. The exterior has scratches, threads, chips, etc. (Tamura Eiji)
Accessories: no accessories
Main Specifications: W597 ✕ H160 ✕ D445mm Weight 3.9 kg
Maintained. This is the highest grade deck in the ES series, bearing the “7,” the final model of the Sony cassette deck. The overwhelming weight and stable operation with a strong body are suitable for a reference machine, and it is also easy to operate intuitively. The sound quality is also sharp, and it is a top level car that achieves both sound and operability. The exterior has line scratches, bumps, and threads. Serial 252215 (Tamura Eiji)
Maintenance information: 2024.4.30 maintained (mechanical drive belt replacement, capstan belt replacement, left pinch roller replacement, head base cleaning and grease up, pinch roller cleaning and grease up, mechanical shaft cleaning and grease up, capstan motor control part electrolytic capacitor replacement. Contact cleaning by detaching the tape half detection switch. Check the tape running path, adjust the left pinch roller height, and check and adjust the playhead azimuth angle. Recording level adjustment volume/BIAS level/EQ volume contact cleaning, Dolby switch contact cleaning, headphone volume replacement, print pattern status check, and additional soldering treatment. Playback level check adjustment, recording level check adjustment, bias level check adjustment, recording calibration operation check adjustment, recording playback test is good, Dolby recording and playback test is good, timer operation test is normal. *Reference value: W&F (WTD): 0.025%, blank residual noise level (-52 dB linear measurement))
Accessories: No accessories
Main specifications: 4 tracks, 2 channels, 3 heads, frequency characteristics, 15 Hz to 22 kHz, W430 x H135 x D380 mm, 12 kg
SAEC long-selling model with a 0.6 m digital cable. 6N ultra-high purity copper with excellent transmission characteristics is used as the conductor material, and transmission loss is reduced with accurate impedance matching (Tamura Eiji)
Maintenance information: 2024.4.4 continuity confirmed
Accessories: none
The price has been reduced! 2024/3/6 sales price 25,000 yen speaker cable 1.0 m pair banana on both ends uses the company's highest-grade cable material. Recommended for those who want to improve the tightness of the low frequencies. On the exterior, there is a part where the rubber ring on the terminal is off. ※The cable is stiff, so please be careful when routing (Tamura Eiji)
Maintenance information: 2024.3.6 continuity confirmed
Accessories: No accessories
The disposal price has been reduced! Member prices are not applicable. 2024/4/24 sales price 118,000 yen*The saran net is cheap because it is not in good condition due to lack of stock, scratches, etc. ATC small bookshelf The thick and powerful mid-low range is attractive. If you pair it with a good amplifier that has torque, you can enjoy it on a scale that greatly exceeds its size. There are scratches on the exterior. Serial 0819/0820 (Tamura Eiji)
Maintenance information: 2024.4.24 sweep test good
Accessories: No accessories
Main specifications: 2 way 2 speakers sealed impedance 8 ohms size W211 x H380 x D250 mm weight 11.4 kg
※It has a cigarette smell, so it's cheap. Currently sold. 115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are scratches on the exterior. Serial 217380XCK00185 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
※It has a cigarette smell, so it's cheap. Currently sold. 115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are scratches on the exterior. Serial 2172380XCK00186 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
※It has a cigarette smell, so it's cheap. Currently sold. 115V specification A German stereo power amplifier with resolution and expressiveness not typical of commercial use. It is proud of its exhilarating sound and outstanding driving power that comes out quickly. The exterior has scratches and paint bald spots. Serial 2172380UGD01107 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 85W+85W (8Ω) 150W+150W (4Ω) W483 x H88 x D270 mm 11.5 kg
Y lug plug set of 4 have mirror-polished terminal contact parts made of leadless brass material with excellent conductivity, and rhodium plating treatment has been applied to the surface to further improve conductivity and durability (Tamura Eiji)
Accessories: original box, instruction manual
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
Disposal prices have been reduced! (Member discounts are not applicable) 2022/5/18 sales price 2,000 yen When used between an S-terminal AV noise filter device and a display, unnecessary noise is removed without deteriorating the amount of information or high frequency characteristics of the video signal at all, and the video signal is organized. The exterior is dull and dirty, and there are floating marks on the label. (TAMURA Eiji)
Maintenance Information: 2022.5.18 Continuity Confirmed
Accessories: There are no accessories
Unused item! Power transformer primary: 90-100-110V secondary: 6.3V/3A x 2, 400-325-0-325-400V/230mA, 5V/3A W122 x H150 x D102 mm 5.4 kg (actual measurement) (Kojima Yosuke)
Accessories: none
Power cable 2.0m PSE standard oxygen-free copper (OFC: oxygen-free copper) is an expressive power cable with high resolution, full of speed (Tamura Eiji)
Maintenance information: 2024.4.30 continuity confirmed
Accessories: case
Power cable 2.0m PSE standard oxygen-free copper (OFC: oxygen-free copper) is an expressive power cable with high resolution, full of speed (Tamura Eiji)
Maintenance information: 2024.4.30 continuity confirmed
Accessories: case
※It is inexpensive because the condition is poor due to scratches, threads, and partial sheath deformation. Off sale power cable, 1.0 m, has an unprocessed end that combines performance and safety at an astonishing level. There are dirt and scratches on the exterior (Tamura Eiji)
Accessories: No accessories
※Because it smells like tobacco, it's cheap. 1 bottle only. Balance cable 4.0m is a standard Neutrik microphone cable. It is also characterized by its soft sound quality and ease of handling (Tamura Eiji)
Maintenance information: 2024.4.30 continuity confirmed
Accessories: No accessories
* It seems to be an output transformer from the specifications; sold 1 piece, primary: 10 kΩ, secondary: 600 ohms, W76 x H71 x D43 mm, 0.6 kg (actual measurement, not including protrusions), there is paint peeling in places (Kojima Yosuke)
Accessories: none
Output transformer sold 1 piece Primary: 14 kPPΩ Secondary: 600 Ω WW76 × H71 × D43 mm 0.6 kg (actual measurement, protrusions not included) There are paint peeling and seal marks in places (Kojima Yosuke)
Accessories: none
A speaker stand with a height of about 20 cm. It is recommended for those who want to build a desktop or compact audio system. The exterior has dullness and small scratches (Tamura Eiji)
Accessories: No accessories
Main specifications: top plate 240 x 210 mm thickness 2.3 mm bottom plate 240 x 210 mm thickness 2.8 mm load capacity 12 kg size W210 x H206 x D 240 mm weight 2.2 kg
The price has been reduced! 2024/3/22 sales price 29,800 yen The tuning hole uniquely arranged on Oyaide's turntable plate thoroughly eliminates unnecessary vibrations that disrupt the record board's trace, and can also be used in combination with a stabilizer to correct the warpage of the record board and expect an appropriate trace. There are small scratches and dullness on the exterior (Tamura Eiji)
Accessories: instruction manual, original box
Main specifications: dimensions: 294 mm, thickest part: 5 mm, 670 g
※Since it is cheap, it will be handed over as is. 1 bottle only 25cm full range speaker made by RCA in the USA. The Alnico magnet responds well and the sound is easy to remove. There are repair marks on the edge (Tamura Eiji)
Maintenance information: 2024.3.22 sweep test good
Accessories: No accessories
Key Specifications: Unit Diameter 25cm 8Ω Fixed Edge
Balance cable is a standard 1.5m pair Accuphase balance cable. It is a natural sound that removes disguise to enhance the characteristics of amplifiers and players. As for the exterior, there is room odor on the sheath (Tamura Eiji)
Maintenance information: 2024.3.14 continuity confirmed
Accessories: none
※It is cheap because it is out of stock and is a spike replacement. A speaker stand that fits the top plate perfectly with JBL's signature speakers 4312, 4425, and 4428 series. Control the sound by filling the pillars with cast iron powder. The sound is like a control monitor with a sharp focus. The exterior has strokes and bruises (Tamura Eiji)
Accessories: spikes (replacement)
Main specifications: top plate W360 x D293 mm bottom plate W440 x H334 x D370 mm (actual measurement) weight 29 kg/bottle
Output transformer sold 1 piece Primary: 5 kΩ Secondary: 6 Ω/600 Ω NFB W68 × H91 × D72 mm 1.28 kg (actual measurement, not including protrusions). From specifications, it seems to be a line output transformer. There are rust spots, scratches, and paint peeling in places (Kojima Yosuke)
Accessories: none
The price has been drastically reduced! 2024/4/17 sales price 69,800 yen ※It is cheap because it has a tobacco smell. Hi-Fi Man's planar drive headphones have a high resolution, and the low frequencies are clear and easy to listen to. The sound balance is flat and the high cushioning is also impressive. The exterior smells like tobacco and there are creases on the cable (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: original box, connection cable
Main specifications: planar drive impedance 50 ohms sound pressure sensitivity 83.5 dB playback frequency band 8 Hz to 65 kHz 505 g
Light and compact, stylish headphones from JVC. The sound has excellent sound insulation and is comfortable to listen to (Tamura Eiji)
Maintenance information: 2024.3.15 sweep check OK
Accessories: case
Main specifications: dynamic type 12 to 24,000 Hz 32 ohms 103 dB 66 g
It is a USB-connected bus-powered D/D converter that uses the C-Media “CM6642” as the digital audio control IC and is compatible with high-resolution sound sources (maximum 24 bit/192 kHz) (Tamura Eiji)
Maintenance information: 2024.4.13 operation confirmed
Accessories: instruction manual, original box
Main specifications: digital input: USB TypeB terminal USB 1.1/2.0 compatible, USBAudioClass 1.0/2.0 compatible digital output: coaxial digital audio output (COAXIAL) optical digital audio input (square) compatible format: PCM maximum 24 bit 192 kHz W40 x H25 x 81 mm 90 g
The disposal price has been reduced. Member prices are not applicable. 2023/12/7 sales price 25,000 yen*Exclusive earth cable is out of stock. Since the cable is soldered to the connection part, it is inexpensive. A sandwich structure with an electromagnetic wave absorbing sheet sandwiched between two aluminum panels. Both sides of the aluminum panel are dark gray and light gray and can be reversed for use. There are line scratches and tape marks on the exterior (Tamura Eiji)
Main specifications: W470 x H7 x D420 mm weight 3.4 kg
The disposal price has been reduced. Member prices are not applicable. 2023/12/7 sales price 25,000 yen*Exclusive earth cable is out of stock. Since the cable is soldered to the connection part, it is inexpensive. A sandwich structure with an electromagnetic wave absorbing sheet sandwiched between two aluminum panels. Both sides of the aluminum panel are dark gray and light gray and can be reversed for use. There are line scratches and tape marks on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: W470 x H7 x D420 mm weight 3.4 kg
*Fully automatic player with built-in Denon phono equalizer currently sold. It is recommended for those who want to enjoy records casually without worrying about the location, or for beginners. There are scratches on the exterior. Serial 0063373998 (Tamura Eiji)
Maintenance information: 2023.12.8 operation confirmed
Accessories: none
Main specifications: fully automatic player belt drive, suitable needle pressure 3.5 g, W360 ✕ H97 ✕ D370 mm, weight 2.9 kg
※It has a cigarette smell, so it's cheap. Since it is 120V specification for commercial use, it will be handed over as is. A compact commercial power amplifier that is highly regarded as a professional studio monitor amplifier. The driving power that cannot be imagined from its size is truly the real thrill of a professional aircraft. The range is reasonable, but it is characterized by a sound image that does not lose sound even at high volumes. There are scratches on the exterior. Serial 8001337592 (Tamura Eiji)
Maintenance information: 2024.4.16 Operation confirmed
Accessories: none
Main specifications: 40W+40W (8Ω) W483 x H44.5 x D213 mm 4.5 kg
*Currently sold. 120V specification. CROWN commercial power amplifier. It features driving power unique to professional use that lifts straight. The high braking power at high volume fully demonstrates the quality of a professional device. The exterior is dull. *There are no fixing brackets for mounting racks. Also, the AC plug has been replaced. Serial 8001294201 (Tamura Eiji)
Maintenance information: 2024.4.11 operation confirmed
Accessories: none
Main specifications: output 25W+25W (8Ω) 120V specification natural air cooling method W483 × H45 × D213 mm 4.5 kg
Mini plug to stereo standard plug conversion cable It is a model using OFC as a wire rod. (Eiji Tamura)
Maintenance information: 2022.1.5 continuity confirmed
Accessories: original box
The price has been reduced! 2024/4/3 sales price 15,000 yen This is a crossover board crossover frequency of 300 Hz for the F-5/F-15. The damping slope can be changed with an internal switch (Tamura Eiji)
Maintenance information: 2024.4.3 operation confirmed (can be checked with F-15)
Accessories: original box
Main specifications: 300Hz attenuation slope 12dB/18dB switchable
The price has been reduced! 2024/4/3 sales price 15,000 yen A rare 1,400Hz frequency board is in stock! It seems to be an Accuphase special order item. A crossover board that can be used for the F-5/F-15. The damping slope can be changed with an internal switch (Tamura Eiji)
Maintenance information: 2024.4.3 operation confirmed (can be checked with F-15)
Accessories: No accessories
Main specifications: 1400 Hz attenuation slope 12 dB/18 dB switchable
Maintained! This is the first AUDIO OF OREGON control amplifier to be in stock in a long time. It is compatible with 117V specification American speakers such as ALTEC and JBL, etc., and although it is a transistor, it doesn't become too stiff and makes you enjoy the firm sound. The exterior has dullness and scratches. ※The plug has been changed. Genuine RF Serial 02117 (Tamura Eiji)
Maintenance information: 2024.4.27 Maintained (no running symptoms. The board vibration check connection was checked. (All pattern parts of the flat amplifier module unit have been added and soldered.) 2024.4.13 Maintained (Electrolytic capacitor replacement in amplifier module. Pattern contact defect correction. (Voice operation check)
Accessories: No accessories
Main specifications: All stages use pure class A operation circuit input phono (mm/47 kΩ) tuner, tape, aux dimensions W483 x H89 x D190 mm weight 4.5 kg