2018 fully restored item. This model omits the MC step-up transformer. The rear speaker terminal has also been changed to one compatible with banana plugs to match modern usability. Although it is a model from the 60s, there is no sense of a faded sound, and it feels like the flat, thick lackstone has been revived energetically. The sound without getting tired even after listening to it for a long time makes me fully experience the luster and warmth of stringed instruments. There are stains all over the exterior, and there are line scratches, fading, etc. on the cabinet (Sasaki Shota)
Maintenance information: 2018.8.25 Maintained (9P socket, SP terminal, RCA terminal, block capacitor, volume/BAL/TCVR, semi-fixed resistor, coupling capacitor, AC cord, resistor replacement. Power SW contact deterioration prevention relay added. SW/VR disassembly, cleaning, solder correction. (Internal and external cleaning, circuit readjustment, waveform check, input/output check, load test, sound output test)
Accessories: copy of the manual
Main specifications: output 10W+10W input terminal AUX1 · 2 Phono 1 · 2 (mm) W470 x H175 x D275 mm weight 14 kg
*Needle cover missing. Elliptical type with built-in boost transformer. It has a rich, rich sound and sounds like an SPU. Clarity has been improved by incorporating a transformer that creates a well-balanced sound. Although it is an MC type, it can be used in the MM position. The exterior has small scratches, dullness, and a feeling of use (Murakoshi Yoichi)
Maintenance information: 2024.5.17 sound output confirmed
Accessories: none
Main specifications: MC type transformer built-in elliptical needle output 10 mV playback frequency band 20 to 20,000 Hz needle pressure 3 to 4.5 g dead weight 32 g
Maintained! SPU round needle type with built-in transformer. This is a shell from the Knicks era. The rich, rich SPU-like sound is attractive. The built-in transformer gives the impression that transparency and clarity have been improved. Needle cover missing. The exterior has a feeling of use such as dullness. Serial 340898 (Murakoshi Yoichi)
Maintenance information: 2024.5.29 Maintained (cantilever, damper adjustment, rubber cover replacement, cleaning)
Accessories: none
Main specifications: MC type with built-in transformer output 10 mV needle pressure 3 to 4.5 g dead weight 32 g
*Needle cover missing. G-shell elliptical needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal cartridge that fully conveys the appeal of analog. There are slight corrosion irregularities on the shell (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
*The headshell is an SPU-G (M) one, but the body is inexpensive because it is GE. Needle cover missing. G-shell oval needle model. The glossy, rich, and heavy sound is attractive without fading. It is an eternal staple cartridge that fully conveys the original appeal of analog. The exterior has rust on the metal parts, and dullness and dirt throughout the body. The needle tip is in good condition (Murakoshi Yoichi)
Maintenance information: 2024.4.17 sound output confirmed
Accessories: none
Main specifications: G shell oval needle MC type output 0.2 mV needle pressure 3 to 4.5 g internal impedance 2 ohms dead weight 31 g
YAMAHA speaker stand The compact stand is made to feel stiff, and you can expect tight sound quality. It can be used for small speakers such as the NS-10M and medium speakers. There are line marks, threads, and tape marks on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: W270 x H494 x D350 mm top plate part W190 W x D175 mm 7 kg/unit
A Yamaha mid-size speaker bracket that can be mounted on a wall or ceiling. It can be used for small speakers such as the NS-10MT and surround speakers. The exterior has dark spots and small scratches (Hitoshi Kobayashi)
Accessories: none
Main specifications: W155 x H190 x D80 mm 0.85 kg
The price has been drastically reduced. 2024/5/15 sales price 118,000 yen Maintained! A famous direct drive machine representative of Technics. The torque is high, the start and stop times are extremely short, and the stable operation that immediately enters constant speed is unique. It also drives LP heavyweights without difficulty. Overall there are small wounds, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (due to disconnection of the FG coil in the motor core, the FG/ angular velocity detection coil was taken out after disassembling the motor core, and the coil pack was rewound. The rotation speed has been reset)
Accessories: copy of instruction manual, power supply
Main specifications: Direct drive aluminum die-cast turntable 33, 45, 78 rotating body W365 x H100 x D360 mm 9.5 kg power supply unit W110 x H85 x D300 mm 3.8 kg
The price has been drastically reduced. 2024/5/3 sales price 99,800 yen Hi-Res compatible USB-DAC, DAC that also functions as a network player. Equipped with ESS Technology's latest generation flagship DAC chip “ES9038PRO.” In addition to PCM sound sources of up to 32 bits/768 kHz, the USB input supports playback of high-resolution sound sources with the highest specifications, such as being compatible with playback of DSD sound sources of up to 22.6 MHz (DSD512) (Tetsuji Oikawa)
Maintenance information: 2024.5.3 operation confirmed
Accessories: remote control, instruction manual, power cable, original box
Main specifications: USB audio input (USB B type) input format stereo PCM stereo DSD (DoP v1.1 or native) PCM sampling frequency 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 352.8 kHz, 384 kHz, 705.6 kHz, 768 kHz PCM quantization bits 16 bits, 24 bits, 32 bit DSD Sampling frequency 2.8224 MHz (DSD64) 5.6448 MHz (DSD128) 11.2896 MHz (DSD256) 22.5792 MHz (DSD512, native only) [coaxial, optical digital input] input format stereo PCM stereo DSD (DoP v1.1) PCM sampling frequency 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz DSD sampling frequency 2.8224 MHz (DSD64 DoP v1.1) compatible audio formats AAC, AIF, AIFF, APE, FLAC, M4A, M4A (Apple Lossless) ALAC, OGG, WAV, WMA, DSF, DFF maximum sampling frequency PCM192 kHz/24 bit/DSD2.8224 MHz (DSD64) W254 x H76 × D360mm weight 4.7 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/3/29 sales price 138,000 yen Sneaky DSM with built-in network player function and 2ch amplifier has arrived. It has a smart design that eliminates anything superfluous, and can be operated with an iPod or the like. Of course, it also has an excellent external input function. There are some minor scratches on the exterior. Genuine Rin Japan. Serial 1333455 (Tomonori Asaine)
Maintenance information: 2024.3.29 Operation confirmed
Accessories: Speakon remote control power cable setup manual
Main specifications: analog input: RCA1 system digital input: coaxial, 1 optical system, 3 HDMI output, 1 HDMI system*RCA has variable output and fixed output can be changed by setting Compatible files: FLAC, WAV, Apple Lossless, AIFF, MP3, WMA, AAC, OGG Compatible Bits: 16 to 24 bits 33W ✕ 4ch (4Ω) W350 ✕ H54.5 ✕ D215mm Weight 2.3 kg
The price has been reduced! 2024/5/12 sales price 148,000 yen A new standard model for the SL-1200 series that inherits the efforts and results that began with the development of the SL-1200G. Outstanding reliability and stability are now available at an affordable price. I'm also happy that it is compatible with 78 revolutions. There is a thread on the dust cover on the exterior (Satoshi Yonejima)
Maintenance information: 2024.5.12 operation confirmed
Accessories: power cord, connection cord, EP adapter, subway, original box
Main Specifications: Direct Drive Turntable System Brushless DC Motor Speed 33 1/3, 45, 78 Universal S-shaped Tone Arm Static Balance Needle Pressure Adjustment Range 0 to 4 g Applicable Cartridge Weight/5.6 to 12.0 g, 14.3 to 20.7 g (including headshell) /when using auxiliary weight/10.0 to 16.4 g, 18.7 to 25.1 g (headshell included) W453 mm x H173 mm x D372 mm approx. 11.5 kg
※This item is currently sold. Onkyo enabled speaker. It is a design that makes it possible to construct a Dolby Atmos sound field using sound reflection from the ceiling. Accessories such as brackets and cables are missing (Sasaki Shota)
Maintenance Information: 2023.12.11 Sweep Test Good
Accessories: none
Main specifications: sealed impedance 6 ohms, playback frequency band 90 Hz to 20 kHz, W120 x H155 x D153 mm, 1.2 kg
The price has been reduced. L2024/2/10 sales price 19,800 yen arm pipe storage keeper It stores the company's 4 arm pipes and is compatible with both AC-300MK2, 400MK2, 3000MC, and 4000MC lengths. Main weights, sub weights, etc. can also be inserted. There is dirt and dullness (Daiki Goto)
Accessories: none
Main specifications: W430 x H40 x D135 mm 740 g (actual measurement)
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/18 sales price 79,800 yen ※It is cheap because the saran is torn or the speaker terminal LF+ on one side does not tighten until the end. Slim tall boy speaker MONITOR AUDIO's middle class, SILVER series, is now in stock. The RS8 has a delicate, highly clear mid to high range tone with good tightness in the low range. The owner has well-balanced characters that can be used from the living room to the tatami room. In addition to dullness and small scratches on the exterior, there is a feeling of use such as a tear on the saran net and sunburn on the main body. Serial 801702/801702 (Tomonori Asae)
Maintenance information: 2024.5.17 sound output checked (good sweep test)
Accessories: Saran net jumper cable (general purpose)
Main specifications: Format: 2.5-way 4 speakers, floor type (anti-magnetic), front & rear port, bass reflex impedance, 6 ohms, allowable input, 175 W, efficiency, 91 dB, frequency characteristics, 33 Hz to 25 kHz, W185 x H900 x D 270 mm, weight 21.0 kg
The price has been reduced. 2024/4/27 sales price 79,800 yen This is a 3-way center speaker with the tuning that best matches the 500, 300, and 100 of the company's Silver series. Since the C350 was designed to pursue only performance without considering size restrictions, the dynamism in terms of sound quality is impressive. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.4.26 Operation confirmed
Accessories: saran net, jumper (general purpose) original box
Main specifications: 3-way sealed frequency characteristics 40Hz-35,000Hz crossover frequency 830Hz/3,200Hz allowable input 200W recommended amplifier output 80-200W W560×H235×D240mm 14.9kg
The disposal price has been reduced! (Member prices are not applicable) 2024/5/21 sales price 1,398,000 yen B&W 40th anniversary limited model of 500 units. Color white. Not only are diamond tweeters that reproduce extremely clear and transparent high frequencies, but their ability to reproduce well-balanced low frequencies is also attractive. The localization is also clear throughout the entire area, and classical music and vocals are reproduced with high quality. There is a line scratch on the base part on one side, a slight thread on the TW dome (no dents), and dents on the grill edge. Serial 0003431,0003432 (Fujisawa Yukishi)
Maintenance information: 2024.5.21 operation confirmed
Accessories: instruction manual, spike, rubber foot, jumper cable
Main specifications: 2-way bass reflex playback frequency band 32 Hz to 33 kHz impedance 8 ohms crossover frequency 3.8 kHz output sound pressure level 88 dB W230 x H930 x D375 mm 25 kg
A classic Technics headshell. Aluminum die-cast body with excellent vibration damping properties (Oikawa Tetsuji)
Accessories: screws
Main specifications: Weight 9.2 g
A rare item. Technics meter unit. 3 modes can be switched. One meter can be used properly for 3 types, making it extremely easy to use. It's a rare gem just for visually enjoying the sound. There are scratches and rust (Oikawa Tetsuji)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: meter sensitivity 0 dBm 20 dBm switchable 3 system input switching W450 x H92 x D378 mm weight 5.3 kg
A rare item. Technics meter unit. 3 modes can be switched. One meter can be used properly for 3 types, making it extremely easy to use. It's a rare gem just for visually enjoying sound (Oikawa Tetsuji)
Maintenance information: 2024.5.29 Operation confirmed
Accessories: none
Main specifications: meter sensitivity 0 dBm 20 dBm switchable 3 system input switching W450 x H92 x D378 mm weight 5.3 kg
Sony die-cast aluminum shell. While it is sturdy, it has a smart design and is easy to use (Oikawa Tetsuji)
Accessories: none
Main specifications: die-cast aluminum, 10.5g dead weight
The disposal price has been reduced. Member discounts are not applicable. 2024/2/6 sales price 59,800 yen ※1 shelf board is missing and has 3 tiers, and is cheap because there are many scratches. A popular large rack. It is a model that can even adjust the storage capacity and height. It also has high performance as an audio rack, and is made of full-bodied natural wood, with a sturdy structure and interior design. You can see a feeling of use, such as appearance, dullness, small scratches, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W1230 x H703 x D563 mm Weight approx. 52 kg
The price has been reduced. 2024/5/30 sales price 128,000 yen*It is cheap because it is in poor condition such as being scratched or the saran net peeling. It is tightly packed with a strong sealed enclosure and a high-quality unit, and the sound is moist and calm. If you drive with an amplifier with a strong drive, you can enjoy the dense mid and low frequencies. The exterior has scratches, scratches, and creases. Serial 02093/02092 (Murakoshi Yoichi)
Maintenance information: 2024.5.29 sound output confirmed
Accessories: saran net
Main specifications: impedance 8Ω output sound pressure level 85dB W220 × H390 × D255 mm 15 kg
※It is inexpensive because there are many scratches on the whole. Although it is small, it is an attractive car with a low range and medium to high range with a solid core in the middle. Bi-wire compatible It is compatible with a wide range of genres, and is recommended not only for pure audio but also for surround sound (Ryo Mizusaki)
Maintenance information: 2024.6.1 sweep test is good
Accessories: nothing
Main specifications: Bi-wiring compatible anti-magnetic design impedance 6 ohms playback frequency band 33 Hz to 45 kHz output sound pressure level 88 dB dimensions W194 x H326 x D318 mm weight 8.4 kg
※There is no problem with operation, but since it is cheap, it will be handed over as is. A threatening center speaker that supports playback up to 90 kHz. If you are looking for detailed sound, please consider it. Equipped with a direct drive super tweeter. There are 4 corks attached to the top plate (Oikawa Tetsuji)
Maintenance information: 2024.4.7 operation confirmed
Accessories: none
Main specifications: 6Ω 80W dimensions W360 x H71 x D163 mm weight 2 kg
HAMILEX speaker stand for small speakers. Recommended for installing small speakers and adjusting the height. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: W230 x H150 x D250 mm 2.0 kg total load capacity 20 kg (1 unit)
This wooden speaker stand is ideal for small and medium speakers. The height is 44cm, making it easy to adjust the listening point. A hard urethane cushioning material is attached to the 4 corners of the top plate (Oikawa Tetsuji)
Accessories: none
Main specifications: top plate W340 x D245 mm height 440 mm bottom plate W380 x D 340 mm 5 kg
High position small speaker stand High density compression boards are used, and rigidity can be expected. The round curved silhouette on the front side is also a point. There are abrasions in places (Kojima Yosuke)
Accessories: none
Main specifications: height 500 mm top plate W240 x D270 (W200 x D250) mm bottom plate W280 x D330 mm weight 6.0 kg/book
The disposal price has been reduced. Member discounts are not applicable. 2023/12/16 sales price 25,000 yen ※1 bottle only. Bass reflex enclosure imitating JBL's mid-size speaker S-99Athena. The lattice grill that symbolizes old JBL is well-made. In addition to being able to see many defects in the exterior and lattice, there is a feeling of use such as dullness, abrasions, small scratches, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: woofer aperture diameter 316 mm, screw pitch (diagonal) 338 mm high range aperture diameter 134 mm, screw pitch (diagonal) 160 mm W610 x H450 x D314 mm 16.5 kg
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are small scratches on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: instruction manual, power cable, original box
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
115V specification A power amplifier that is supported by a heavyweight power transformer and reproduces tight low frequency reproduction with good visibility. It shows high cost performance that exceeds size and price. There are small scratches on the exterior (Hiura Katsuji)
Maintenance information: 2024.5.26 sound output confirmed
Accessories: instruction manual, power cable, original box
Main specifications: 45W+45W (8Ω) 75W+75W (4Ω) W483 × H51 × D295mm 7.5 kg
The disposal price has been reduced! (Member price not applicable) 2024/4/12 sales price 70,000 yen B&W 805D series speaker stand. Equipped with a spike insulator “T-PROP”. It is a speaker stand with a completely new concept developed with the theme of eliminating speaker stress as much as possible by absorbing and releasing it in a natural way without putting a load on the diamond formation structure. The exterior has scratches, paint peeling, and bumps. (FUJISAWA KOSHI)
Accessories: insulator T-PROP, screws
Main specifications: top plate W227 x D306 mm B&W 805 Diamond, D3 specially designed bottom plate W280 x D360 mm height 500 mm approx. 15 kg
Speaker stand for B&W 805D series Equipped with a spike insulator “T-PROP”. It is a speaker stand with a completely new concept developed with the goal of suppressing speaker stress by absorbing and releasing it without applying a load due to the diamond formation structure (Daiki Goto)
Accessories: spikes, T-PROP
Main specifications: top plate W227 x D306 mm B&W 805 Diamond, D3 specially designed bottom plate W280 x D360 mm height 500 mm approx. 15 kg
The disposal price has been reduced! (Member discounts are not applicable) 2023/5/11 sales price 148,000 yen The BBC monitor speaker is equipped with an in-house manufactured unit based on the LS3/5A, and the phase characteristics and frequency characteristics of the mid to low range, and the responsiveness of music signals have been greatly improved. You can listen to traditional English sounds with a sense of calm. The exterior has a feeling of use such as dullness and small scratches. Serial 206B08481 206B08482 (Tomonori Asaine)
Maintenance information: 2024.5.11 operation confirmed
Accessories: saran net
Main specifications: 2 way 2 speakers sealed crossover 5 kHz impedance 8 ohms frequency characteristics 75 Hz to 20 kHz output sound pressure level 84 dB input terminal 4 mm terminal bywire compatible W165 ✕ H305 ✕ D 190 mm weight 4.6 kg
A popular SME classic headshell with a stylish design. It's lightweight, which is essential for light needle pressure arms and heavy cartridges, and after all, this is the best fit for SME arms. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.26 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 8g
Internal and external maintenance has been applied and brushed up! JBL 40th anniversary model! A reprint model of the L101. You can enjoy the excellent sound unique to horn drivers. It has a good response and is a spacious speaker that can be matched with music of a wide range of ages. The traditional lattice net design is also attractive. There is slight discoloration on the marble (Murakoshi Yoichi)
Maintenance information: 2024.5.29 maintenance (exterior repair/polishing/oil finish
Front and rear baffles/hakama repair/painting. Lattice repair/polishing/painting, lining replacement. Woofer edge replacement. Driver maintenance (magnetic circuit gap cleaning center adjustment). Network maintenance (frequency characteristic check, ATT cleaning).)
Accessories: lattice
Main specifications: 2 way · 2 speakers · bass reflex system · floor type frequency characteristics 35 Hz to 16,000 Hz directional characteristics (horizontal x vertical) 90 degrees x 40 degrees sound pressure level 92 dB 8 Ω allowable input 150 W crossover frequency 900 Hz enclosure volume 53.5 L W445 x H629 x D320 mm 29.1 kg/book
Real sound processor for home theaters Just by connecting to a home theater speaker, the sound image and localization become clear, the live feeling increases, and the surround effect is enhanced. There are tape marks on the exterior. Serial 001288 (Tamura Eiji)
Maintenance information: 2024.4.24 Operation confirmed
Accessories: none
Main specifications: Compatible impedance of 4 ohms to 6 ohms is desirable, maximum output of 1 kW or less is desirable, W113 x H41 x D56 mm, mass approx. 170 g
A rare tone arm from RS Labs that was introduced and sold in a radio technical magazine in 1996. As with linear tracking, the tracking error is zero. The head shell part rotates freely, and the structure automatically adjusts so that tracking errors are always zero. The straight arm lowered from a high position to eliminate downforce is impressive. It is a legendary device that goes beyond the overview of traditional tone arms and reproduces analog (Murakoshi Yoichi)
Maintenance information: 2024.5.31 continuity confirmed
Accessories: original box, main weight, sub weight, hex wrench, instruction manual (English copy)
Main specifications: One-point support arm effective length 215mm
A rare Rotel thin phono equalizer. It has a flat, neutral tone with no distractions, and I like how simple it is to use. There are small scratches, dullness, and the electrical outlet has changed (Oikawa Tetsuji)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual, original box
Main specifications: input sensitivity MM: 2.5 mV/47 kΩ MC: 210 mV/100 Ω size W440 × H72 × D195 mm weight 3.1 kg
The price has been reduced. 2024/2/23 sales price 35,000 yen KRK powered speaker equipped with a Class D power amplifier. The amplifier section is equipped with an equalizer to help adjust room acoustics (Sasaki Shota)
Maintenance information: 2024.2.23 Operation confirmed
Accessories: power cable, original box
Main specifications: 2-way 145 W playback frequency band 42 Hz to 40 kHz input balance, standard jack W225 x H339 x D284 mm 7.6 kg
Currently sold. The tuner's auto tuning is not working, but the current situation is. This K series CD/USB receiver is compatible with playback of iPods/iPhones, USB memory devices, etc. This is a flat, unobtrusive amplifier with a straightforward sound. It can also be connected to a PC and is recommended for those who want to get started with desktop audio. Appearance, dullness, small scratches, and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 operation confirmed (tuner auto tuning not working, other operations confirmed)
Accessories: remote control, power cord
Main specifications: 50W+50W W245 x H104 x D309 mm weight 5.7 kg
The disposal price has been reduced. Member prices are not applicable. 2024/5/20 sales price 198,000 yen Kappa series improved model Renaissance 90. The mid-high range is composed of EMIM and EMIT special units, and the sound is extremely delicate and clear. The deep sound field space and glossy, moisturized mid to high frequencies are unique to ribbon units. It has high resolution throughout the entire range and is suitable for classical and vocal styles. There are small scratches and line wounds, and there are repair marks of broken decorative plates at the foot (Oikawa Tetsuji)
Maintenance information: 2013.12.15 Maintained (exterior repair and cleaning. (Back side urethane deteriorated, replaced with substitute urethane)
Accessories: spikes
Main specifications: 4 way 4 speakers sealed floor type EMIT tweeter EMIM mid-range ribbon type 87dB 4Ω 250W W435 x H1245 x D315 mm 35.8 kg
The 1.2m pair of unprocessed speaker cable has excellent balance from low to high frequencies, and has an energetic and warm tone. There are threads and disappearing characters on the exterior (Tamura Eiji)
Maintenance information: 2024.5.24 Operation confirmed
Accessories: none
Tannoy rectangular yoke type enclosure by Shinkosha, a popular domestic box manufacturer. It is attractive because it is made to sound good. A 30cm unit adapter (detachable) is attached to the baffle surface, and casters are attached to the bottom (Murakoshi Yoichi)
Accessories: none
Main specifications: W597 x H108 x D37 mm weight 30 kg
The price has been reduced. 2024/4/26 sales price 12,800 yen. This is a rare KEF center speaker Q6C in stock. It is a well-balanced and well-organized sound character typical of the Q series. It seems to express a sufficient sense of sound field even when used in combination with Q1 for theaters. There is a bruise on the upper back corner. Serial 2027685G (Murakoshi Yoichi)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: jumper plate, saran net
Main specifications: 2-way bass reflex low range/130mm Uni-Q high range/19mm Luminiumdome frequency characteristics 50Hz-27kHz crossover frequency 2.8kHz 89dB 8Ω W432xH160xD215mm 4.1 kg
※1 bottle only. Woofer for the famous Japanese instrument 2S-305. The Alnico magnet makes a pleasant low frequency. How about for repairs or for a new system? The urethane part is defective due to deterioration. (FUJISAWA KOSHI)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: No accessories
Main specifications: Alnico magnet, 30 cm, 8 ohms, 20 W, 40 Hz to 1500 Hz, diameter: 313 x depth: 168 mm, weight: 8.5 kg
The price has been reduced. 2017/10/6 sales price 3,000 yen This is a speaker mounting bracket when using the speaker system PS-S200 series etc. as a ceiling suspension. There are spots, rust, and small scratches on the exterior. One single-sided pin is missing (Wang Exhibition)
Accessories: none
Main specifications: compatible models PS-S224W/WH, PS-S226W, PS-S203W, PS-S204W, PS-S207W,
PS-S550W, PS-S552W, PS-S553, etc. Load capacity 12 kg, angle adjustable 1.13 kg
A record player equipped with a Bluetooth (R) function and a USB output terminal. It can be connected to a Bluetooth (R) compatible wireless speaker, etc., and is recommended for those who want to enjoy a record player casually. As for the exterior, there is a thread on the dust cover. Serial 1007740 (Tamura Eiji)
Maintenance information: 2024.5.19 Operation confirmed
Accessories: AC adapter, EP adapter
Main specifications: W516 × H198 × D433m mass 5 kg
Maintained! A popular DENON control amplifier for its excellent phono equalizer. MC head amplifiers are famous for their quality, and they fully draw out the amount of information in the cartridge. It's a neat sound typical of a domestic amplifier with clear yet solid mid-range sound. In addition to the exterior, noticeable scuffs on the top plate, scratches on the VOL dial, and stains on the back of the front flap, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.2.16 Maintained (main volume, balance volume internal contact cleaning, cleaning. All input terminals are polished and cleaned, electrolytic capacitor replaced, PHONO2 impedance changeover switch disassembly, contact polishing, cleaning, and grease is applied. (Check the operation of each input/output)
Accessories: instruction manual (copy)
Main specifications: CR equalizer with 3 PHONO inputs MC head amplifier W455 x H132 x D357 mm 10.5 kg